This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_SPI_FLASH_SPANSION in defconfigs of LS1046ARDB and
LS1046AQDS which have two spansion flases i.e s25fs512s each of size
64M.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Some of these options are not used by the driver anymore and some of
them are obsolete as the information is gathered from the dt. Also
consolidating defines in common headers.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
TFABOOT support includes:
- ls1046aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- FMAN address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_MISC_INIT_R
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
Sata is equipped on ls1046a and can be a boot source. Add sata boot
support as an option if available.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Increase setup, assertion and hold time related to chip-select signal.
Additional delay is needed for the signal to propogate through FPGA.
This adjustment slightly increase the read and write cycle but has no
impact on burst read or write.
Signed-off-by: York Sun <york.sun@nxp.com>
This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.
Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>
Because COMFIG_DM_USB has been enabled and will not use it anymore.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
use Kconfig to select xhci accordingly.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Use Kconfig to select QE-HDLC and USB pin-mux.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Fix a bug of 'commit 8104deb2d6 ("armv8: layerscape: Adjust memory
mapping for Flash/SD card on LS1046A")' as NAND block size is 256KB
on LS1046AQDS.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This commit removes definitions of CONFIG_SYS_BARGSIZE defined to be
equal to CONFIG_SYS_CBSIZE in numerous configuration files.
We remove such definitions in two situations:
- CONFIG_SYS_CBSIZE is otherwise not defined in the board
configuration file, which means the default value of
CONFIG_SYS_CBSIZE == 256 applies. In this case, the default value
of CONFIG_SYS_BARGSIZE == 512 (common/image.c) is suitable, as it is
larger.
- CONFIG_SYS_CBSIZE is defined in the board configuration file, but
to a value equal or less than 512. In this case, the default value
of CONFIG_SYS_BARGSIZE == 512 (common.image.c) is suitable, as it
is equal or larger.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that the fallback value of CONFIG_SYS_PBSIZE in
include/config_fallbacks.h has been adjusted, remove its definition
from a large number of board configuration files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This syncs all of the currently Kconfig'd symbols out of the headers and
into the defconfig files. This has two exceptions, first am335x_evm
needs to be converted to DM in SPL and then it can stop undef'ing
CONFIG_DM_USB. Leaving this as-is results in a build failure, and
without work, run time failure. The other case is am43xx_evm.h and in
turn am43xx_evm_usbhost_boot. The problem here is that we need DWC3 USB
host mode in SPL, but still desire to have gadget mode in U-Boot proper.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested on ls1046ardb with automatically boot Ubuntu from SD card or
USB disk, if it fails to detect external storage disk, fall back to
qspi boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch is to adjust the memory mapping for FLash/SD card on
LS1046AQDS and LS1046ARDB, such as FMAN firmware load address, U-Boot
start address on serial flash and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
With d53ecad92f some unused interrupt related code was removed.
However all of these options are currently unused. Rather than migrate
some of these options to Kconfig we just remove the code in question.
The only related code changes here are that in some cases we use
CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename
and move the value local to the code in question.
Fixes: d53ecad92f ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi")
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix the offsets of MTD partitions on Nor flash on ls1043ardb,
ls1043aqds and ls1046aqds boards. Delete the rcw, uboot env and fman
partitions. Add user partitions for general usage.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the DDR interactive debugging to reduce the size of spl image.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The LS1046AQDS processor has three integrated USB 3.0 controllers
(USB1, USB2, and USB3) that allow direct connection to the USB
ports with appropriate protection circuitry and power supplies.
USB1 and USB2 ports are powered by a NX5P2190UK device, which
supplies 5v power at up to 1.2 A. The power enable and
power-fault-detect pins are connected to the LS1046A processor
via CPLD for individual port management.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
