`nand_get_flash_type()` allows identification of supported NAND flashs.
The function is useful in SPL (like mxs_nand_spl.c) to lookup for a NAND
flash (which does not support ONFi) instead of using nand_simple.c and
hard-coding all required NAND parameters.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
The PFUZE3000 uses registers addresses up to 0xff.
The DM pfuze100 driver supports both pfuze100 and pfuze3000. Allow it
to use the device type to return the correct number of registers.
Also rename the too generic PMIC_NUM_OF_REGS enumeration value for
pfuze3000 to match the other "PFUZE3000_" prefixed enumerations and the
pfuze100 enumeration value PFUZE100_NUM_OF_REGS.
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add support for specified ECC strength/size using device tree
properties nand-ecc-strength/nand-ecc-step-size.
This aligns behavior with the mainline driver, such that:
- If fsl,use-minimal-ecc is requested it will use data from
data sheet/ONFI. If this is not available the driver will fail.
- If nand-ecc-strength/nand-ecc-step-size are specified those
value will be used.
- By default maximum possible ECC strength is used
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Support driver data from device tree. Also support fsl,use-minimal-ecc
similar to Linux' GPMI NAND driver.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
In preparation for device tree support separate board init
from controller init similar to other raw NAND drivers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This function initializes DMA descriptors so mxs_nand_init_dma is
more precise. It also frees up the rather generic name mxs_nand_init.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Move GPMI and BCH register structs to the driver struct mxs_nand_info
in prepartion for device tree support.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Add support for minimum ECC strength supported by the NAND chip.
This aligns with the behavior when using the fsl,use-minimum-ecc
device tree property in Linux.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Report correct ECC parameters back to the stack. Do not report
bytes as we have it not immeaditly available and the Linux version
also does not report it. It seems to have no aversive effect.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Calculate BCH geometry at start and store the information in
a structure. This avoids recalculation on every page access
and allows to calculate ECC relevant information in one place.
This patch does not change ECC layout or driver behavior in
any way.
The patch aligns the driver somewhat with the Linux GPMI NAND
driver which drives the same IP.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Add config option which allows to enable on flash bad block table
support. This has the same effect as when using the device tree
property "nand-on-flash-bbt" in Linux.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Instead of completing initialization via scan_bbt callback use
NAND self init to initialize the GPMI (MXS) NAND controller.
Suggested-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
In preparation to convert the driver to use NAND self init
provide a new minimal init for SPL builds. As a side effect
this also reduces size of SPL by about 4KiB.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
commit 8480792287
("spi: omap3: Skip set_mode, set_speed from claim") did break SPI
support on my AM335x board.
The named commit:
- ignored the responsible arguments (speed, mode)
The set speed/mode function must use the supplied function arguments to
work properly. With this commit we take those arguments and transfer
them to the priv-data.
- used wrong udevice pointer for getting priv data
the udevice-pointer within function argument is already the spi-bus
device, so it is wrong looking here for some parent (ocp-bus in this
case) and getting priv-pointer from there.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Otherwise the frequency is zero and the clock divider cannot be setup by
'omap3_spi_set_speed' function.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
CS GPIO activation low/high is determinated by the device tree
so we don't need to take in accoung in cs_activate and cs_deactivate
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch replaced "return 0" with "return status" to fix the
incorrect return value error reported by the coverity.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
In Linux, the clock rate of the UART is given by the clock driver.
If you try to follow that in U-Boot, you would end up with adding
more u-boot,dm-pre-reloc properties, and also the clock driver would
be too big for SPL, which is used for UniPhier ARMv7 platform.
The current solution is to add 'clock-frequency' property to the
UART nodes, but it does not exist in the DT files in Linux. I do
not want to let DT diverge for U-Boot.
Check the SoC compatible and set the clock rate according to it.
This will be helpful to sync DT between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the clk framework to initialize clocks from drivers that need them
instead of having hardcoded frequencies and initializations from board
code.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a basic clock driver for Amlogic Meson SoCs which supports
enabling/disabling clock gates and getting their frequency.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SARADC driver was merged after the following commit :
commit d35812368a ("regmap: change regmap_init_mem() to take ofnode instead udevice")
Thus breaking build, this patch fixes the regmap_init_mem accordingly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
At present the code overruns the bar[] array. Fix this.
At the same time, drop the leading / from the "/spl" path so that we can
run U-Boot SPL with:
spl/u-boot-spl
rather than requiring:
/path/to/spl/u-boot-spl
Reported-by: Coverity (CID: 131199)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move the strdup() call so that it is only done when we know we will bind
the device.
Reported-by: Coverity (CID: 131216)
Signed-off-by: Simon Glass <sjg@chromium.org>
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The RAVB only supports 100Full and 1000Full operation, it does not support
10Full or any Half-duplex modes. The PHY could still advertise those features
though, so filter out the PHY features accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Do not stop the clock in the start callback in case of failure, keep
them running to also keep the PHY running. The failure could be ie.
PHY failing to negotiate link and if the clock get shut down, another
attempt at bringing the link up would fail. The clock right now are
started in probe function and stopped in remove function, which is
the correct behavior.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The sh_pfc_{read,write}() must operate on the register address directly
rather than on an offset, fix this to prevent illegal access.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There are multiple GPIO banks with up to 32 pins / bank. When
using 'gpio status -a' to read the pins, this patch displays
both GPIO<bank>_<index> similar to how the device trees
display in addition to displaying gpio_#
Signed-off-by: Adam Ford <aford173@gmail.com>
When enabling BLOCK_CACHE on devices with limited RAM during SPL,
some devices may not boot. This creates an option to enable
block caching in SPL by defaults off. It is dependent on SPL_BLK
Fixes: 46960ad6d0 ("block: Have BLOCK_CACHE default to y in some cases")
Signed-off-by: Adam Ford <aford173@gmail.com>
The naming with "UART" is obviously wrong, we fix this here.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This adds a DM video driver for U-Boot as the EFI payload. The driver
makes use of all necessary information from the passed EFI GOP info
to create a linear framebuffer device, as if it were initialized by
U-Boot itself.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This function is used only inside this driver that's why should be
static.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This issue was found when OF_LIVE was enabled that there are scrambled
chars on the console like this:
Chip ID: zu3eg
Watchdog: Started��j� sdhci@ff160000: 0, sdhci@ff170000: 1
In: serial@ff010000
I found a solution for this problem exactly the same as I found later in
serial_msm fixed by:
"serial: serial_msm: initialize uart only before relocation"
(sha1: 7e5ad796bc)
What it is happening is that output TX fifo still contains chars to be
sent and _uart_zynq_serial_init() resets TX fifo even in the middle of
transfer.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change logic and put char to fifo till there is a space in output fifo.
Origin logic was that output fifo needs to be empty. It means only one
char was in output queue.
Also remove unused ZYNQ_UART_SR_TXEMPTY macro.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Coding style is checking to use BIT macros instead of shifts.
The patch is also fixing the rest of macros which should be BITs instead
of hex numbers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use u32 instead of int for max_bank, bank_min and bank_max. These values
can't be negative that's why no reason to use signed type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Code around tuning_loop_counter variable expects to go below zero.
That's why this variable can't use unsigned type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch fixes the mmc tuning command failures
when tuning pattern data needs to read back for
comparision against the expected bit pattern.
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This function is required for adding bootstage support.
Also enable it directly for ZynqMP R5 configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
struct sunxi_ccm_reg doesn't have ahb_reset0_cfg on sun4i and sun5i,
thus compilation fails with:
drivers/usb/host/ohci-sunxi.c:96:26: error: 'struct sunxi_ccm_reg' has
no member named 'ahb_reset0_cfg'
Access this reg using its offset to fix this issue.
Fixes commit 1ed9c1118 ("usb: sunxi: ehci: get rid of ifdefs")
and commit 56830cee3 ("usb: sunxi: ohci: get rid of ifdefs")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Functions can return NULL in case of error that's why checking return
value is needed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In case of phyread()/phy_setup_op() timeout code is working with
uninitialized phyreg variable. Initialize this variable to make sure
that code it not working with random value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
wait_for_bit_le32 returns negative value on failure. Fix phy...() to
handle these failures properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Combine repeated code from smi_reg_read/smi_reg_write into a common
function smi_wait_ready.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On the SPEAr600 SoC, which has the dwmac1000 variant of the IP block,
the DMA reset never succeeds when a MII PHY is used (no problem with a
GMII PHY). The designware_eth_init() function sets the
DMAMAC_SRST bit in the DMA_BUS_MODE register, and then
polls until this bit clears. When a MII PHY is used, with the current
driver, this bit never clears and the driver therefore doesn't work.
The reason is that the PS bit of the GMAC_CONTROL register should be
correctly configured for the DMA reset to work. When the PS bit is 0,
it tells the MAC we have a GMII PHY, when the PS bit is 1, it tells
the MAC we have a MII PHY.
Doing a DMA reset clears all registers, so the PS bit is cleared as
well. This makes the DMA reset work fine with a GMII PHY. However,
with MII PHY, the PS bit should be set.
We have identified this issue thanks to two SPEAr600 platform:
- One equipped with a GMII PHY, with which the existing driver was
working fine.
- One equipped with a MII PHY, where the current driver fails because
the DMA reset times out.
Note: Taken from https://www.spinics.net/lists/netdev/msg432578.html
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When connecting to from a CPU direct to a 88e6097 typically RGMII is
used. In order for traffic to actually pass we need to force the link up
so the CPU MAC on the other end will see the link.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This makes sure the DMA buffers are properly aligned for the
hardware.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add driver for Socionext AVE ethernet controller that includes MAC and
MDIO bus supporting RGMII/RMII modes.
The driver behaves the ethernet driver model (DM_ETH) with devicetree.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
VCAP tables must be initialized even if no advanced classification
is used. If no initialization is performed, then ECC error will
be observed by the user when the first packet enters the l2switch.
The error is marked in MPIC_EISR0 -bit 29 which means - Internal RAM
multi-bit ECC error.
This patch fixes the aforementioned ECC error by performing the
initialization of VCAP tables.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If you send a final packet just before stopping the interface (e.g. a final
ACK as part of the UDP fastboot protocol), then that packet isn't reliably
delivered onto the wire.
Reap packets prior to stopping the interface to ensure any which are
in-flight make it out. Also remove buffer and len from the call to
cpdma_process() as we weren't using them on their return.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for Cortina CS4223 10G PHY
- As per the CS4223 specs, an EEPROM module is
connected to the PHY. At startup the PHY reads
the firmware line and tries to load the firmware
into the internal memory.
- This driver reads the EEPROM status
and checks if firmware has been loaded
Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Put the enetaddr data in the same order as it was before the change in
commit ace1520cb5 ("net: sunxi-emac: Write HW address via function")
Reported-by: Udo Maslo <u.maslo@web.de>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Bus translations should be applied when reading the address of the sgmii
phy registers from the DT. Use ofnode_get_addr_index instead of the
plain ofnode_read_u32_default to fix this.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On A64 OHCI1 clock source is OHCI0 clock, so we need to enable OHCI0
clock when OHCI1 is in use.
Fixes commit dd3228170a ("usb: sunxi: Switch to use generic-phy")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
If U-Boot gets used as coreboot payload all pci resources got
assigned by coreboot. If a dts without any pci ranges gets used
the dm is not able to access pci device memory. To get things
working make use of a 1:1 mapping for bus <-> phy addresses.
This change makes it possible to get the e1000 U-Boot driver
working on a sandybridge device where U-Boot is used as coreboot
payload.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed 'u-boot' in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If we use U-Boot as coreboot payload with a generic dts without
any ranges specified we fail in pci pre_probe and our pci bus
is not usable.
So convert decode_regions(..) into a void function and do the simple
error handling there.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed 'u-boot' in the commit message and checkpatch warning]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This fixes the following compiler warning:
"warning: cast from pointer to integer of different size
[-Wpointer-to-int-cast]"
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Starting with cpuid level 0x16 (Skylake-based processors)
it is possible to get CPU base freq via cpuid.
This fixes booting on a skylake based system.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed wrong indention of labels]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add WARN_ONCE definition to allow single time notification
of warnings to the user.
Taken from Linux kernel (4.17) with slight changes
(Removed __section(.data.once))
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
[trini: Drop the musb and dwc3 compat versions]
Signed-off-by: Tom Rini <trini@konsulko.com>
When dealing with filesystems that come from block devices we can get a
noticeable performance gain in some use cases from having the block
cache enabled. The code paths are valid in other cases when we have BLK
set and may provide wins in raw reads in some use cases, so have this be
default when BLK is enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
Equivalent code that disables the hidden i2c0 slave already exists in
the Turris Omnia platform specific code. But this hidden i2c0 slave that
interferes the i2c bus is not board specific. Armada 38x SoCs and at
least some Kirkwood variants are affected as well. Add code to disable
this slave to the i2c bus driver to make it work on all affected
hardware.
Use the bind callback because we want this to always run at boot,
regardless of whether U-Boot uses the i2c bus.
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
I just stumbled over some cluttered UBI messages. It seems some newline
chars are missing in the current U-Boot UBI source. Lets fix this
in U-Boot as well (Linux has those fixes already).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Since commit 0e373c0ade ("spl: add SPL_RESET_SUPPORT"),
reset is supported in SPL, enable this flag for STM32F SoCs family.
This allows to remove a specific case in RCC mfd driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Split the rtc_{get,set,reset} functions so that the bodies can be used
in a DM driver.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This flash IC is used in some chromebook models
manufactured by Bitland.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The clean_bar() function resets the SPI NOR BAR register to 0, but
does not set the flash->curr_bar to 0 , therefore those two can get
out of sync, which could ultimatelly result in corrupted flash content.
The simplest test case is this:
=> mw 0x10000000 0x1234abcd 0x4000
=> sf probe
=> sf erase 0x1000000 0x10000
=> sf write 0x10000000 0x1000000 0x10000
=> sf probe ; sf read 0x12000000 0 0x10000 ; md 0x12000000
That is, erase a sector above the 16 MiB boundary and write it with
random pre-configured data. What will actually happen without this
patch is the sector will be erased, but the data will be written to
BAR 0 offset 0x0 in the flash.
This is because the erase command will call write_bar()+clean_bar(),
which will leave flash->bank_curr = 1 while the hardware BAR registers
will be set to 0 through clean_bar(). The subsequent write will also
trigger write_bar()+clean_bar(), but write_bar checks if the target
bank == flash->bank_curr and if so, does NOT reconfigure the BAR in
the SPI NOR. Since flash->bank_curr is still 1 and out of sync with
the HW, the condition matches, BAR programming is skipped and write
ends up at address 0x0, thus corrupting flash content.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Change to use devfdt_get_addr_index() function to get fdt address.
Original code has compilation warning below:
drivers/spi/cadence_qspi.c: In function ‘cadence_spi_ofdata_to_platdata’:
drivers/spi/cadence_qspi.c:297:18: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
plat->regbase = (void *)data[0];
^
drivers/spi/cadence_qspi.c:298:18: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
plat->ahbbase = (void *)data[2];
^
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
If compile with support for the efi loader we need to mark the pages
allocated for the framebuffer as reserved so the kernel won't attempt
to use them for other uses.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Also fix bad accents in my name.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Also fix bad accents in my name.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Also fix bad accents in my name.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Also fix bad accents in my name.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds support for loading secure bitstreams on ZynqMP
platforms. The secure bitstream images has to be generated using
Xilinx bootgen tool.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to load secure bitstreams(authenticated or
encrypted or both). As of now, this feature is added and tested only
for xilinx bitstreams and the secure bitstream was generated using
xilinx bootgen tool, but the command is defined in more generic way.
Command example to load authenticated and device key
encrypted bitstream is as follows
"fpga loads 0 100000 2000000 0 1"
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add new compatible to the Ethernet AVB driver for R8A77990 E3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add new compatible to the Uniphier SD driver for R8A77990 E3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add new compatible to the GPIO driver for R8A77990 E3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds initial pinctrl driver to support for the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This follows the style of existion PORT_GP_X macros and
will be used by a follow-up patch for the r8a77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The PE clock have two parents, add support for picking the correct
one and deriving the clock from it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The PLL rate could be in the GHz range, which could overflow a 32bit
data type. Since the hardware is 64bit anyway, pass the clock rates
as 64bit number internally to avoid this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The mul and div arguments were reported in reverse order in the debug
message, swap them to fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds HS200 suuport for ZynqMP and enables
the same for ZC1751 DC1 board which has eMMC on it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use live-tree functions.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reason to specify header with full soc name.
Symlink is setup automatically (arch -> arch-zynqmp)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Convert USB fastboot code to use shared fastboot protocol.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce 'oem format' which matches the USB implementation, guard this
with CONFIG_FASTBOOT_CMD_OEM_FORMAT so that you can configure it out.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce CONFIG_IMAGE_SPARSE and CONFIG_CMD_MMC_SWRITE so the "mmc
swrite" command is separated from the fastboot code.
Move image-sparse from common to lib so it's clear it's library code.
Rename CONFIG_FASTBOOT_FLASH_FILLBUF_SIZE to CONFIG_IMAGE_SPARSE_FILLBUF_SIZE
and migrate it to Kconfig.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add FASTBOOT_FLASH_NAND_TRIMFFS to Kconfig; note there are no in-tree
users of it.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename fb_mmc_flash_write/fb_mmc_erase/fb_nand_flash_write/fb_nand_erase to
fastboot_... as they form a public interface
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move FASTBOOT_VERSION to include/fastboot.h so when we merge the UDP code
we only have one definition.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Rename fb_set_reboot_flag to fastboot_set_reboot_flag so it matches
all other fastboot code in the global name space. Fix the guards around
them so that they're dependent on FASTBOOT, not just USB_FUNCTION_FASTBOOT.
Move the weak implementation of fastboot_set_reboot_flag to fb_common.c
so we can call it from non-USB fastboot code.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Compiling on a 64 bit target the arguments to _fb_nand_write are
incompatible:
drivers/fastboot/fb_nand.c: In function ‘_fb_nand_write’:
drivers/fastboot/fb_nand.c:101:42: warning: passing argument 3 of ‘nand_write_skip_bad’ from incompatible pointer type [-Wincompatible-pointer-types]
return nand_write_skip_bad(mtd, offset, &length, written,
^
In file included from drivers/fastboot/fb_nand.c:16:0:
include/nand.h:107:5: note: expected ‘size_t * {aka long unsigned int *}’ but argument is of type ‘unsigned int *’
int nand_write_skip_bad(struct mtd_info *mtd, loff_t offset, size_t *length,
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
CONFIG_FASTBOOT_GPT_NAME and CONFIG_FASTBOOT_MBR_NAME are always defined
by Kconfig if you're compiling this code, so remove these redundant
defaults.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add newlines so we format our output correctly.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jocelyn Bohr <bohr@google.com>
Ensure that when selecting FASTBOOT_FLASH you end up with a buildable
configuration. Prior to this you could select NAND without MTDPARTS
and end up with an image which (surprisingly) excluded NAND.
Also fix dependencies on FASTBOOT_GPT_NAME/FASTBOOT_MBR_NAME which require
you have EFI_PARTITION/DOS_PARTITION enabled.
Delete redundant FASTBOOT_FLASH_NAND_DEV from Kconfig - it was only ever
used as a guard and the value was ignored in all cases, we're using
FASTBOOT_FLASH_NAND as the guard now.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Add drivers/fastboot/fb_common.c, where fastboot_okay/fail are implemented
so we can call them from a non-USB implementation.
Introduce fastboot_response which takes varargs parameters so we can
use it to generate formatted response strings. Refactor fastboot_okay/fail
to use it.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Add the response string as a parameter to fastboot_okay/fail, instead
of modifying a global, to match the contract expected by the AOSP
U-Boot code.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.
Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There are memory leaks of usb request and its buffer for ep0,
in_ep, and out ep. Fix memory leaks of usb request and its buffer.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
The xhci wrapper-driver for Rockchip searches the DTS to find its
child node compatbile with 'rockchip,rk3399-usb3-phy' to retrieve the
base-address of the PHY. However, this is currently broken (and
always has been), returning NULL. However, the (wrongly) retrieved
base-address is never used.
We thus remove this code for now.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
In xhci_set_configuration(), 'Context Entries' field in the slot
context was cleared with mask LAST_CTX_MASK, but it should have
taken the endianness into consideration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If a full speed hub connects to a high speed hub which supports MTT,
the MTT field of its slot context will be set to 1 when xHCI driver
setups an xHCI virtual device in xhci_setup_addressable_virt_dev().
Once usb core fetch its hub descriptor, and need to update the xHC's
internal data structures for the device, the HUB field of its slot
context will be set to 1 too, meanwhile MTT is also set before, this
will cause configure endpoint command fail. In the case, we should
clear MTT to 0 for full speed hub according to section 6.2.2.
This keeps in sync with Linux kernel commit:
096b110: usb: xhci: fix config fail of FS hub behind a HS hub with MTT
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Per xHCI spec chapter 6.2.2 table 6-7, as input, software shall
initialize the dev_state field to '0'. Though this does not seem
to cause any issue with most xHC implementations, let's do this
to conform with the spec.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
If a USB 3.0 hub is plugged into the root port of the xHC, the xHCI
driver will issue a 'Configure Endpoint' command to the xHC for it
to update its internal data structure for this hub device. The hub
attributes are in the slot context so we need tell xHC to update the
slot context by setting the add context flags of the input control
context to only cover the slot context.
At present the add context flags is or'ed with the slot context bit,
but it should really be accurately set to the slot context, as the
variable that holds the value of the add context flags comes from
whatever was set in the last command execution, which may contain
additional contexts that 'Configure Endpoint' command should not
touch. Some xHC implementations like x86 don't complain such, but
it was observed on Renesas RCar Gen3 platform that the RCar xHC
complains with a 'TRB error' completion codes as the response.
Reported-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
During the execution of xhci_deregister xHCI registers are accessed. If
the clock is already deactivated when xhci_deregister is called this can
lead to undefined behavior. Change the order to deregister the device
before deactivating the clock.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
ftsmc020_init is not used anymore.
So it can be removed.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
The compatible string of ftsdc010_mci.c is different from
the mmc driver in Linux Kernel. Modify it for consistency.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Fix warnings as below when compile in 64-bit.
warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Fix warning as below when compile in 64-bit.
warning: format '%u' expects argument of type
'unsigned int', but argument 6 has type 'size_t
{aka long unsigned int}
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Mvebu AHCI is AHCI driver which uses SCSI under the hood.
This patch adjusts AHCI setup to support SCSI by creating
a SCSI device as a child. Since the functions of creating
SCSI device need the kconfig option DM_SCSI, so let
AHCI_MVEBU select DM_SCSI.
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This workaround was added for A8040/7040 A0.
A8040/7040 A0 is no longer supported so this workaround
can be removed.
Signed-off-by: David Sniatkiwicz <davidsn@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently mvebu sata driver is in arch/arm/mach_mvebu directory, this
patch moves it to drivers/ata directory with renaming "sata.c" to
"ahci_mvebu.c" which is aligned to Linux.
New ahci driver's kconfig option is added as AHCI_MVEBU which selects
SCSI_AHCI and is based on AHCI.
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
When the pin control driver selects SD/eMMC function for
a pin group, there is additional configuration to be done
for this case - switch the PHY to work with SDHCI interface.
This patch adds the missing functionality into the pin
control driver.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
For pinctrl driver of mvebu, the compatible strings
supported are defined differently from Linux version.
The patch aligned the compatible string with
Linux 4.17-rc4.
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Allwinner USB PHY handling can be done through driver-model
generic-phy so add the generic-phy ops to relevant places
on host and musb sunxi driver and enable them in respective
SOC's.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.
The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner A23 has 2 USB PHY's and 0x04 has phy ctrl offset.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner A33 has 2 USB PHY's and 0x10 has phy ctrl offset.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Add PHY configs for Allwinner A10/A13/A20 which are SUN4I.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Unlike, other Allwinner SUN4I Phy supporting SOC, A83T has
2 USB PHY's and second one is HSIC. So phy control need to
configure to handle these HSIC and SIDDQ requirement.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
ID and VBUS detection code require when musb changing
between Host and/or Peripheral modes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
USB PHY implementation for Allwinner SOC's can be handling
in to single driver with different phy configs.
This driver handle all Allwinner USB PHY's start from 4I to
50I(except 9I). Currently added A64 compatibility more will
add in next coming patches.
Current implementation is unable to get pinctrl, clock and reset
details from DT since the dm code on these will add it future.
Driver named as phy-sun4i-usb.c since the same PHY logic
work for all Allwinner SOC's start from 4I to A64 except 9I
with different phy configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Like other Allwinner SoC, the H3/H5/A64 is missing the config register
from the musb hardware block. Use a known working value for it
like other SoC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Add OTG device clkgate and reset for H3/H5 through driver_data.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Unlike other Allwinner SOC's H3/H5/V3s OTG support 4 endpoints
with relevant fifo configs, rest all have 5 endpoints.
So add the fifo configs and defer them based on driver_data.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Filling musb_hdrc pdata using structure will unnecessary
add extra ifdefs, so fill them inside probe call for
better code understanding and get rid ifdefs using
devicetree compatible.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
- add proper macros for musb_config members
- use bool 'true' for multipoint and dyn_fifo instead of numerical 1
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Move struct sunxi_ccm_reg pointer to private structure
so-that accessing ccm reg base become more proper way
and avoid local initialization in each function.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
SDMMC_CMD_CPSMEN bit is wrongly check and set in
SDMMC_ARG register instead of SDMMC_CMD register.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add support of fuse command (read/write/program/sense)
on bank 0 to access to BSEC SAFMEM (4096 OTP bits).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add possibility to update the serial parity used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Rename USART_ISR_FLAG_xxx bits to USART_ISR_xxx bits and
USART_ICR_OREF to USART_ICR_ORECF in order to match datasheets.
Sort defines by descendant order.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for early debug printf, before the availability of
driver model and device tree support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Serial port configuration was missing from previous implementation.
It only worked because it was preconfigured by LK.
This patch configures the uart for 115200 8N1.
It also configures the pin mux for uart pins using DT bindings.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The uart is already initialized prior to relocation,
reinitialization after relocation is unnecessary.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Failure to set the clocks will causes data abort exception when
trying to write to AHB uart registers.
This patch ensures that we don't touch these registers if clock
setting failed.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, if we happen to allocate an address requiring 64 bits to a
device only supporting 32-bit BARs, the address eventually gets silently
truncated to 32 bits. Avoid this by adding a new flag to
pciauto_region_allocate() to bail out in such situations.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
All of the debug output from this file is squished to one line. Fix
it.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, qemu_arm_defconfig and qemu_arm64_defconfig only work with
the 'highmem=off' parameter passed to QEMU's virt machine. The reason is
that when 'highmem' is not disabled, QEMU appends 64-bit a memory
resource to the PCI controller's regions property in DT in addition to
the 32-bit PCI memory window in low memory. And the current DT parsing
code picks the last (thus the 64-bit one) memory resource, whose address
eventually gets silently truncated to 32 bits because
CONFIG_SYS_PCI_64BIT is not set, which obviously causes PCI to break.
Avoid this problem by ignoring memory regions whose addresses are above
the 32-bit boundary when CONFIG_SYS_PCI_64BIT is not set.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver can emulate all the basic functionalities of a TPMv2.x
chip and should behave like them during regular testing.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
On some designs, the reset line could not be connected to the SoC reset
line, in this case, request the GPIO and ensure the chip gets reset.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the tpm2_tis_spi driver that should support any TPMv2 compliant
(SPI) module.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Choice between v1 and v2 compliant functions is done with the
configuration.
Create the various files that will receive TPMv2-only code on the same
scheme as for the TPMv1 code.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are no changes in this commit but a new organization of the code
as follow.
* cmd/ directory:
> move existing code from cmd/tpm.c in cmd/tpm-common.c
> move specific code in cmd/tpm-v1.c
> create a specific header file with generic definitions for
commands only called cmd/tpm-user-utils.h
* lib/ directory:
> move existing code from lib/tpm.c in lib/tpm-common.c
> move specific code in lib/tpm-v1.c
> create a specific header file with generic definitions for
the library itself called lib/tpm-utils.h
* include/ directory:
> move existing code from include/tpm.h in include/tpm-common.h
> move specific code in include/tpm-v1.h
Code designated as 'common' is compiled if TPM are used. Code designated
as 'specific' is compiled only if the right specification has been
selected.
All files include tpm-common.h.
Files in cmd/ include tpm-user-utils.h.
Files in lib/ include tpm-utils.h.
Depending on the specification, files may include either (not both)
tpm-v1.h or tpm-v2.h.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix a few more cases of tpm.h -> tpm-v1.h, some Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
Because both major revisions are not compatible at all, let's make them
mutually exclusive in Kconfig. This way we will be sure, when using a
command or a library function that it is supported by the right
revision.
Current drivers are currently prefixed by "tpm_", we will prefix TPMv2.x
files by "tpm2_" to make the distinction without moving everything.
The Kconfig menu about TPM drivers is now divided into two sections, one
for each specification. Compliant drivers with one specification will
only show up if this specification _only_ has been selected, otherwise a
comment is displayed.
Once a driver is selected by the user, it selects automatically a
boolean value, that is needed in order to activate the TPM commands.
Selecting the TPM commands will automatically select the right
command/library files.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework deps as TPM_V1 and TPM_V2 depend on TPM,
drop TPM_DRIVER_SELECTED]
Signed-off-by: Tom Rini <trini@konsulko.com>
TPM are shipped with a few read-only register from which we can retrieve
for instance:
- vendor ID
- product ID
- revision ID
Product and vendor ID share the same register and are already referenced
in the tpm_chip structure. Add the revision ID entry which is missing.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for DEBUG_UART on ARC devboards
This required us to do 2 things:
1) Insert a call to debug_uart_init() in early boot code
2) Convert serial_arc to Kconfig
Once both items above are done we just patched defconfigs.
Some minor fixes for the Raspberry Pi:
- Fix SD writes on new sdhost controller
- Sanitize default load addresses, allowing for better payload placement
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=te7/
-----END PGP SIGNATURE-----
Merge tag 'signed-rpi-next' of git://github.com/agraf/u-boot
Patch queue for rpi - 2018-05-24
Some minor fixes for the Raspberry Pi:
- Fix SD writes on new sdhost controller
- Sanitize default load addresses, allowing for better payload placement
Last user of this driver went away in May 2017 in commit
eb5ba3aefd ("i2c: Drop use of CONFIG_I2C_HARD").
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Heiko Schocher <hs@denx.de>
Last user of this driver went away in June 2015 in commit
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Heiko Schocher <hs@denx.de>
Last user of this driver went away in June 2015 in commit
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
dm_warn is too noisy, replace with dev_dbg for less noise.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Convert CONFIG_SUPPORT_EMMC_RPMB to Kconfig. Split the command handling
from the underlying support and expose this through CMD_MMC_RPMB.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The bcm2835 sdhost driver has a problem with "write multiple" commands.
It seems to boil down to the fact that the controller dislikes its FIFO
to get drained at the end of a block when a write multiple blocks command
is in flight.
The easy fix is to simply get rid of all the IRQ driven logic and make
the driver push as much data into the FIFO as it can. That way we never
drain and we never run into the problem.
Reported-by: Jan Leonhardt <jan@cyberdesigner.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since 'commit f82290afc8 ("mtd: ubi: Fix worker handling")',
when booting from NAND, on a fresh NAND just after being flashed (and
only in this case), we got the following log:
ubi0: default fastmap pool size: 200
ubi0: default fastmap WL pool size: 100
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0 error: ubi_update_fastmap: could not find any anchor PEB
ubi0 error: ubi_update_fastmap: could not find any anchor PEB
ubi0 error: ubi_wl_get_peb: Unable to get a free PEB from user WL pool
ubi0 error: autoresize: cannot auto-resize volume 1
UBI error: cannot attach mtd2UBI error: cannot initialize UBI, error
-28UBI init error 28
After analysis, in ubi_wl_init(), when performing schedule_erase(),
thread_enabled flag is not yet set to 1, which forbids ubi_do_worker()
to execute pending works.
This has to effect to not populate ubi->free with free physical
eraseblocks.
Following Richard Weinberger's advice, this patch has been
backported from kernel tree :
'commit 1cb8f9776c7d ("ubi: fastmap: Implement produce_free_peb()")'
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Heiko Schocher <hs@denx.de>
Add derivative of the rcar_i2c driver which is capable of
probing itself from DM and uses DT.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Remove the rcar_i2c driver, since it's no longer used by any
board and will be superseded by a DM and DT capable variant.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
devm_zalloc() is already defined in dm/device.h header, so
devm_zalloc can be removed from linux_compact.h beader file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Switch to DM_USB was done and there is no need to keep !DM_USB code in
tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By enabling BLK by default this is the next driver which needs to get
support for DM_USB. Adding generic DWC3 glue logic which only
parse nodes and read device mode. Based on it probe proper
host/peripheral DWC3 drivers for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support to get maximum speed from dt so that usb drivers
makes use of it for DT parsing.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
(rebase and fix errors)
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch is preparing dwc3 core for enabling DM_USB with peripheral
driver with using driver model support.
The driver will be bound by the DWC3 wrapper driver based on the
dr_mode device tree entry.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
(Remove dwc3-omap changes)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds phy tranceiver driver for STM32 USB PHY
Controller (usbphyc) that provides dual port High-Speed
phy for OTG (single port) and EHCI/OHCI host controller
(two ports).
One port of the phy is shared between the two USB controllers
through a UTMI+ switch.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
During file download, it only uses 32bit variable for file size and
it limits maximum file size less than 4GB. Update to support more
than 4GB file with using two 32bit variables for file size as thor
protocol 5.0.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
The thor sender can send filename without null character and it is
used without consideration of overflow. Actually, character array
for filename is assigned with DEFINE_CACHE_ALIGN_BUFFER() and it
is bigger than size of memcpy, so there was no real overflow.
Fix filename overflow for code level integrity.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
This patch enables DDR Kconfig support for Arria 10.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
Current sdram driver is only applied to gen5 device, hence it is better
to rename sdram driver to more specific name which is related to gen5
device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
This change enables support for MC34708 PMIC in sandbox. Now we can
emulate the I2C transfers larger than 1 byte.
Notable changes for this driver:
- From now on the register number is not equal to index in the buffer,
which emulates the PMIC registers
- The PMIC register's pool is now dynamically allocated up till
64 regs * 3 bytes each = 192 B
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for MC34708 PMIC, to be used with driver model
(DM).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit provides support for transmissions larger than 1 byte for
PMIC devices used with DM (e.g. MC34708 from NXP).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The struct uc_pmic_priv's trans_len field stores the number of types to
be transmitted per PMIC transfer.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When Kconfig support was added for MVGBE it included automatically
selected PHYLIB support. But MVGBE does not need PHYLIB it will build
fine without it. Commit ed52ea507f ("net: add Kconfig for MVGBE")
should have been a no-op in terms of build size but because of the
selecting PHYLIB the openrd configs increased in size.
Remove the automatic selection of PHYLIB, boards that need it will have
already enabled it in their config header file.
Fixes: commit ed52ea507f ("net: add Kconfig for MVGBE")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
In
void *rx_addr = NULL;
rx_add = A;
the first assignment has no effect. Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
