Previous patch "MLK-18044-4: crypto: caam: Fix pointer size to 32bit
for i.MX8M" breaks the 64 bits CAAM.
Since i.MX CAAM are all 32 bits no matter the ARM arch (32 or 64),
to adapt and not break 64 bits CAAM support, add a new config
CONFIG_CAAM_64BIT and new relevant type "caam_dma_addr_t".
This config is default enabled when CONFIG_PHYS_64BIT is set except
for iMX8M.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The signature is generated using manufacturing protection private key.
Fix typo in fsl_mfgprot.c.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add DEK blob encapsulation support for IMX8M through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application call.
U-boot sends and receives the DEK and the DEK blob binaries through OP-TEE
dynamic shared memory.
To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The CAAM block used in i.MX8M is 32 bits address size but when the flag
PHYS_64BIT is enabled for armv8, the CAAM driver will try to use a
wrong pointer size.
This patch fixes this issue.
Signed-off-by: Aymen Sghaier <aymen.sghaier@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enabling CAAM driver for i.MX8M platforms, a 64 bits architecture,
lead to casting warnings: from/to pointer to/from integer with
different size. This patch fix these warnings
Signed-off-by: Aymen Sghaier <aymen.sghaier@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The blob command is not working on i.MX7D, i.MX8MQ and i.MX8MM
devices.
Due to different cache management it's necessary to flush dcache
range for destination address so data can be available in memory.
Add necessary operations in blob_encap() and blob_decap() functions.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This code was originally developed by Raul Cardenas <raul.casas@nxp.com>
and modified to be applied in U-Boot imx_v2017.03.
More information about the initial submission can be seen
in the link below:
https://lists.denx.de/pipermail/u-boot/2016-February/245273.html
i.MX7D has an a protection feature for Manufacturing process.
This feature uses asymmetric encryption to sign and verify
authenticated software handled between parties. This command
enables the use of such feature.
The private key is unique and generated once per device.
And it is stored in secure memory and only accessible by CAAM.
Therefore, the public key generation and signature functions
are the only functions available for the user.
The manufacturing-protection authentication process can be used to
authenticate the chip to the OEM's server.
Command usage:
Print the public key for the device.
- mfgprot pubk
Generates Signature over given data.
- mfgprot sign <data_address> <data_size>
Signed-off-by: Raul Ulises Cardenas <raul.casas@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MQ B2 also has fixed value in OCOTP_READ_FUSE_DATA register,
so it does not support "fuse sense" command like B1.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
VDD SOC normal run changed to 0.85V
LPDDR4 freq0 change from 4000MTS to 2400MTS
Signed-off-by: haidong.zheng <haidong.zheng@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Linux commit a75bbe71a27 ("mtd: rawnand: fsl_ifc: fix FSL NAND driver to
read all ONFI parameter pages")
Per ONFI specification (Rev. 4.0), if the CRC of the first parameter page
read is not valid, the host should read redundant parameter page copies.
Fix FSL NAND driver to read the two redundant copies which are mandatory
in the specification.
Signed-off-by: Jane Wan <Jane.Wan@nokia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As on some incipient Layerscape platforms (LS1043A series) there isn't
separate PF control register block, these registers reside in the LUT
register block, so when the driver detected there isn't 'ctrl', it will
assign the 'lut' address to the ls_pcie->ctrl.
The current code allocate memory for the struct ls_pcie with random
contents, this can result in skipping to assign the ls_pcie->ctrl with
the 'lut' address, then further crash with the incorrect address.
Fixes: 118e58e26e ("pci: layerscape: Split the EP and RC driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As far as u-boot is concerned the ds1339 is compatible with the other
devices supported by the ds1307 driver. The Linux driver does expose
some additional functionality but as far as u-boot is concerned just
adding the compatible string is enough.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At the moment the nvme_get_features() and nvme_set_features() functions
carry a (somewhat misleading) comment about missing cache maintenance.
As it turns out, nvme_get_features() has no caller at all in the tree,
and nvme_set_features' only user doesn't use a DMA buffer.
Mention that in the comment, and leave some breadcrumbs for the future,
should those functions attract more users.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At the moment nvme_read_completion_status() tries to invalidate a single
member of the cqes[] array, which is shady as just a single entry is
not cache line aligned.
The structure is dictated by hardware, and with 16 bytes is smaller than
any cache line we usually deal with. Also multiple entries need to be
consecutive in memory, so we can't pad them to cover a whole cache line.
As a consequence we can only always invalidate all of them - U-Boot just
uses two of them anyway. This is fine, as they are only ever read by the
CPU (apart from the initial zeroing), so they can't become dirty.
Make this obvious by always invalidating the whole array, regardless of
the entry number we are about to read.
Also blow up the allocation size to cover whole cache lines, to avoid
other heap allocations to sneak in.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
The module defines a duplicate uclass driver for UCLASS_SIMPLE_BUS, but
it is not allowed. This breaks of-platdata and makes the result
non-deterministic.
The driver does not need to be an uclass driver, so lets remove it. I
had turned it into an uclass driver because I thought wrongly it had to
call the dm_scan_fdt_dev routine to work properly, but some tests on the
board have shown otherwise.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
building with MTK_AHCI enabled results in implicit declaration and
undefined reference of dev_err followed by a segfault of gcc
drivers/ata/mtk_ahci.c: In function 'mtk_ahci_parse_property':
drivers/ata/mtk_ahci.c:65:4: warning:
implicit declaration of function 'dev_err'
drivers/ata/mtk_ahci.c:65: undefined reference to `dev_err'
in function `mtk_ahci_probe':
drivers/ata/mtk_ahci.c:92: undefined reference to `dev_err'
Segmentation fault
fix this by adding the dm/device_compat.h to includes
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
commit e58e68d9 ("mmc: mtk-sd: assign plat->cfg.f_max with a correct value")
wrongly assumed that plat->cfg.f_max is always unset at the time
mscd_drv_probe() is run. This is not true in case max-frequency being
defined in device tree, as it is then already set by mmc_of_parse()
in msdc_of_to_plat().
Only set plat->cfg.f_max to the default maximum value in case it is
not already set to a sane value.
Fixes: e58e68d93e ("mmc: mtk-sd: assign plat->cfg.f_max with a correct value")
Cc: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
-----BEGIN PGP SIGNATURE-----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=nIJc
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210312' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Add WATCHDOG_RESET() in MTD framework and STM32 QSPI driver
- stm32mp1_trusted_defconfig rely on SCMI support
- Remove the nand MTD configuration for NOR boot in stm32mp1 board
- STM32programmer update
- Bsec: manage clock when present in device tree
- stm32mp15: move bootdelay configuration in defconfig
- Update for stm32 dsi and dw_mipi_dsi
- STM32 MCU's cleanup
- Fix compilation issue depending on SYS_DCACHE_OFF and SYS_ICACHE_OFF flags
- Update stm32mp1 doc
Config option ARMADA_39X is never set so remove all dead code hidden under
ifdef CONFIG_ARMADA_39X blocks.
Also remove useless checks for CONFIG_ARMADA_38X define as this macro is
always defined for a38x code path.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marvell Armada 3720 Functional Errata, Guidelines, and Restrictions
document describes in erratum 4.1 PCIe value of vendor ID (Ref #: 243):
The readback value of VEND_ID (RD0070000h [15:0]) is 1B4Bh, while it
should read 11ABh.
The firmware can write the correct value, 11ABh, through VEND_ID
(RD0076044h [15:0]).
Implement this workaround in U-Boot PCIe controller driver aardvark for
both PCI vendor id and PCI subsystem vendor id.
This change affects PCI vendor id of PCIe root bridge emulated by Linux
kernel. With this change Linux kernel reports correct vendor id 11AB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The arrays `pbs_dq_mapping`, `div_ratio1to1` and `div_ratio2to1` have
different bounds declared in header files where these variables are also
defined from the ones declared in source files.
This causes the compiler to complain (when building with LTO):
ddr3_sdram.c:24:12: warning: type of ‘pbs_dq_mapping’ does not match
original declaration
[-Wlto-type-mismatch]
ddr3_patterns_64bit.h:911:5: note: array types have different bounds
ddr3_patterns_64bit.h:911:5: note: ‘pbs_dq_mapping’ was previously
declared here
ddr3_dfs.c:45:11: warning: type of ‘div_ratio1to1’ does not match
original declaration [-Wlto-type-mismatch]
ddr3_axp_vars.h:167:4: note: array types have different bounds
ddr3_axp_vars.h:167:4: note: ‘div_ratio1to1’ was previously declared
here
ddr3_dfs.c:46:11: warning: type of ‘div_ratio2to1’ does not match
original declaration [-Wlto-type-mismatch]
ddr3_axp_vars.h:196:4: note: array types have different bounds
ddr3_axp_vars.h:196:4: note: ‘div_ratio2to1’ was previously declared
here
CI managed to trigger this as an error when compiling with LTO for AXP.
Fix this by using values from the header files, which seem to be the
correct ones.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
In arch/arm/mach-mvebu/dram.c we always include axp's xor.h for common
XOR definitions, regardless whether we compile for axp or a38x.
But the declaration of this function has a different signature in axp's
xor.h from the one used in a38x' implementation - one parameter is u64
instead of u32. This can result in wrong argument's being passed to that
function on a38x with no one the wiser.
I discovered this when building U-Boot for Turris Omnia with LTO. The
compiler complains about the different signatures being thrown into the
same linking process:
axp/xor.h:67:5: warning: type of ‘mv_xor_mem_init’ does not match
original declaration [-Wlto-type-mismatch]
67 | int mv_xor_mem_init(u32 chan, u32 start_ptr, u32 block_size,
| ^
a38x/xor.c:165:5: note: type mismatch in parameter 3
165 | int mv_xor_mem_init(u32 chan, u32 start_ptr, unsigned long long
| ^
a38x/xor.c:165:5: note: type ‘long long unsigned int’ should match
type ‘u32’
Fix this by changing the type of the block_size argument in the axp's
implementation and header file to the one used in a38x (and upstream
mv-ddr-marvell).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This syncs drivers/ddr/marvell/a38x/ with the master branch of repository
https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git up to the
commit 7c351731d196 ("Merge pull request #29 from pali/sync-a38x-uboot").
This patch was created by following steps:
1. Replace all a38x files in U-Boot tree by files from upstream github
Marvell mv-ddr-marvell repository.
2. Run following command to omit portions not relevant for a38x and ddr3:
files=drivers/ddr/marvell/a38x/*
sed 's/#if defined(CONFIG_ARMADA_38X) || defined(CONFIG_ARMADA_39X)/#ifdef TRUE/' -i $files
unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_DDR4 -UCONFIG_APN806 \
-UCONFIG_MC_STATIC -UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \
-UCONFIG_PHY_STATIC_PRINT -UCONFIG_CUSTOMER_BOARD_SUPPORT \
-UCONFIG_A3700 -UA3900 -UA80X0 -UA70X0 -DTRUE $files
3. Manually omit SPDX-License-Identifier changes from this patch as
upstream license in upstream github repository contains long license
texts and U-Boot is using just SPDX-License-Identifier.
After applying this patch, a38x ddr3 code in upstream Marvell github
repository and in U-Boot would be fully identical. So in future applying
above steps could be used to sync code again.
The only change in this patch is removal of dead code and some fixes with
include files.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
commit 258be123226f8f5cd516b7813fe201fb7d7416e9 upstream.
At this moment, only page 0 of SPD is being read but to support
smbios, we need to read page 1 also which has more info. In order
to do that, we need to allocate more space.
Signed-off-by: Sujeet Baranwal <sujeet.baranwal@cavium.com>
Tested-by: sa_ip-sw-jenkins <sa_ip-sw-jenkins@marvell.com>
Reviewed-by: Sujeet Kumar Baranwal <Sujeet.Baranwal@cavium.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <judge.packham@gmail.com>
The DSI phy can be turned on from the DSI digital interface in
the dphy_enable() function or from a dedicated DSI phy "wrapper"
in phy_ops->init() function. If the STM32MP1 case, the wrapper
is used then the dphy_enable() "warning" traces are not relevant.
This patch moves these "warning" traces to "debug" traces so
they are still available for DSI phy based on the digital
interface in debug logging mode, but not there in normal mode
for both cases.
Note: The related Linux kernel driver uses a "debug"
message too.
Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Yannick Fertre <yannick.fertre@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove the child device of the STM32 DSI bridge when the driver probe
failed to stop futher probe request on panels used with STMicroelectronics
board (orisetech_otm8009a.c or raydium-rm68200.c driver).
This patch avoid the trace "cannot get reset GPIO" when
STM32MP157 device tree is used on stm32MP151 SOC without DSI support.
In this hw_version value is 0, as DSI bridge is absent and the panel
ofdata_to_platdata is called for each try of panel probe,
the gpio reset pin is requested but after dsi father probe failed).
For the next request, the PANEL ofdata_to_platdata failed as the gpio
is already used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reorder include files in expected order.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Define LOG_CATEGORY to allow filtering with log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Include the file needed for log function prototype, this patch solves the
compilation issue for undefined reference to `dev_err'.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This change makes stm32mp1 clock driver to get the root clocks
reference from the device node in the FDT rather than fetching
straight these clocks by their name. Driver now stores the
clock reference and use it to know if a root clock is present,
get its rate or gets its related udevice reference.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
In case of big area read/write on spi nand, watchdog timeout may occurs.
To fix that, add WATCHDOG_RESET() in spinand_mtd_read() and
spinand_mtd_write() to ensure that watchdog is reset.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case of big area erased on nand, watchdog timeout may occurs.
To fix that, add WATCHDOG_RESET() in nanddev_mtd_erase() to ensure that
watchdog is reset.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case of reading large area and memory-map mode is misconfigured
(memory-map size declared lower than the real size of the memory chip)
watchdog can be triggered.
Add WATCHDOG_RESET() in _stm32_qspi_read_fifo to fix it.
Issue reproduced with stm32mp157c-ev1 board and memory map size set to
1, with following command:
sf read 0xC0000000 0 0x4000000
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case of big area write/erase on spi nor, watchdog timeout may occurs.
Issue reproduced on stm32mp157c-ev1 with following commands:
sf write 0xC0000000 0 0x3000000
or
sf erase 0 0x1000000
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When flush cache of the current GPD and resume QMU, the controller
will try to access the next GPD after processing the current one,
if not flush the next GPD, the controller may get wrong GPD status.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
This option is better placed in the x86 code since it is not generic
enough to be in the core code. Move it.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed a typo in arch/x86/Kconfig]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Fix the treshold typo in code by threshold.
Fixes: c0165c85c3 ("button: add a simple Analog to Digital Converter device based button driver")
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
sysreset uclass driver provides an implementation of 'reset'
command using the sysreset_ APIs unconditionally. It also
supports the 'poweroff' command using the sysreset_ APIs,
but under a Kconfig option CONFIG_SYSRESET_CMD_POWEROFF.
Let's do the same for the 'reset' command, by introducing a
new Kconfig option CONFIG_SYSRESET_CMD_RESET, and set it to
on by default, to allow a board that don't have a sysreset
reset driver yet, but have a sysreset poweroff driver to
compile without any issue.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
dev_read_addr_size_index() returns fdt_addr_t which might be a
64-bit physical address. This might be true for some 85xx SoCs
whose CCSBAR is mapped beyond 4 GiB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The VirtIO BLK driver depends on the blk uclass driver.
Add the dependency in the Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present the driver only supports 32-bit bus and cpu address.
The controller's outbound registers/fields for extended address
are not programmed. Let's program them to support 64-bit bus and
cpu address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
devfdt_get_addr_index() returns fdt_addr_t which might be a 64-bit
physical address. Use map_physmem() to return the virtual address
that can be used by a 32-bit machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For the QEMU ppce500 machine, LAW registers are not implemented
hence CONFIG_FSL_LAW is not turned on and all LAW APIs are not
available. We should wrap all LAW registers programming in the
mpc85xx PCI driver with CONFIG_FSL_LAW.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
