To enable HS400(ES) and UHS for imx8m platforms, update the driver data
to share with imx8qm esdhc_soc_data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
During mmc initialization, there are several calls to mmc_set_clock
and mmc_set_ios. When mmc_power_off, the mmc->clock will be set,
but the imx driver will use 400KHz. So the following calls
to mmc_set_ios will set the clock several times which is redundant
in fsl_esdhc_imx driver. So let's simplify to remove redundant
clock settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The QorIQ eSDHC on all platforms supports checking write protect
state through register bit. So check it always.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The fsl_esdhc_init() was actually to get configuration of mmc_config.
So rename it to fsl_esdhc_get_cfg_common() and make it common for both
DM_MMC and non-DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to clean up bus width setting code.
- For DM_MMC, remove getting "bus-width" from device tree.
This has been done in mmc_of_parse().
- For non-DM_MMC, move bus width configuration from fsl_esdhc_init()
to fsl_esdhc_initialize() which is non-DM_MMC specific.
And fix up bus width configuration to support only 1-bit, 4-bit,
or 8-bit. Keep using 8-bit if it's not set because many platforms
use driver without providing max bus width.
- Remove bus_width member from fsl_esdhc_priv structure.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Voltage validation should be done by CMD8. Current comparison between
mmc_cfg voltages and host voltage capabilities is meaningless.
So drop current comparison and let voltage validation is through CMD8.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Controller initialization is not needed in fsl_esdhc_init().
It will be done in esdhc_init() for non-DM_MMC, and in
esdhc_init_common() in probe for DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Conver TI CPSW driver to use dev/ofnode api.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[trini: Add <dm/ofnode.h> to provide the prototype to ofnode]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add support for Intel FSP-S and FSP-T in binman
- Correct priority selection for image loaders for SPL
- Add a size check for TPL
- Various small SPL/TPL bug fixes and changes
- SPI: Add support for memory-mapped flash
On i.MX7 in a sake of reducing the disturbances caused by a neighboring
cells in the FCB page in the NAND chip, a randomizer is enabled when
reading the FCB page by ROM bootloader.
Add API for setting BCH to specific layout (and restoring it back) used by
ROM bootloader to be able to burn it in a proper way to NAND using
nandbcb command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Need to pass total 5 arguments for SIP HAB call on i.MX8MQ,
so update the interface to add new argument.
Signed-off-by: Ye Li <ye.li@nxp.com>
[agust: fixed imx8m-power-domain build]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Set gd->fb_base so it can be shown with bdinfo command.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The expire_now function was previously setting the watchdog timeout to
minimum and waiting for the watchdog to expire. However, this watchdog
also has bits to trigger immediate reset. Use those instead, like the
Linux imx2_wdt driver does.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
The Linux imx2_wdt driver uses a fsl,ext-reset-output boolean in the
device tree to specify whether the board design should use the external
reset instead of the internal reset. Use this boolean to determine which
mode to use rather than using external reset unconditionally.
For the legacy non-DM mode, the external reset is always used in order
to maintain the previous behavior.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Now AM65x CPSW2G driver will disable MAC TX internal delay for PHY
interface mode "rgmii-rxid" which is incorrect. Hence, fix it by keeping
default value (enabled) for MAC TX internal delay when "rgmii-rxid"
interface mode is selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Now TI CPSW driver will disable MAC TX internal delay for PHY interface
mode "rgmii-rxid" which is incorrect.
Hence, fix it by keeping default value (enabled) for MAC TX internal delay
when "rgmii-rxid" interface mode is selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
This patch adds support for standard Ethernet "max-speed" DT property to
allow PHY link speed limitation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
According to TRMs the 10Mbps link speed is supported in RGMII only when
CPSW2G MAC SL is configured for External Control ("in band") mode
CPSW_SL_MACCTRL.EXT_EN(18) = 1.
Hence update cpsw_slave_update_link() to follow documentation.
[1] https://patchwork.kernel.org/patch/10285239/
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
At present the value of the timer base is used to determine whether the
timer has been set up or not. It is true that the timer is essentially
never exactly 0 when it is read. However 'time 0' may indicate the time
that the machine was reset so it is useful to be able to denote that.
Update the code to use a separate flag instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function can be called before the timer is set up. Make sure that the
init function is called so that it works correctly.
This is needed so that bootstage can work correctly in TPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 platforms the SPI flash can be mapped into memory so that the
contents can be read with normal memory accesses.
Add a new SPI method to find the location of the SPI flash in memory. This
differs from the existing device-tree "memory-map" mechanism in that the
location can be discovered at run-time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ARC fixes for v2020.01-rc2
The main change is move to DM_MMC of yet 2 another ARC boards:
AXS101 & IoTDK.
Among that we improve handling of stock-formatted SD-cards of high volume
on EM SDP as well as introduction of reset driver for HSDK which is required
for prepser reinitialization of some peripherals like USB etc.
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
-----BEGIN PGP SIGNATURE-----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=f0m8
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc2
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
Bootstage improvements for TPL, SPL
Various sandbox and dm improvements and fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl24zDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZRiwf+Mf7oG//zjiZcHaPP6KOFb1CjwqLSuiaI
eCYB6GEZXuSpc8MjAw+baAfIw8MMFuaCfPsUQ5dDo391neK0sW9kkEsdcXnQBpB3
GdJYcewLN1UuJZovriGobIisGc0GQHh8gmRcVGWSKoEt+gAQauRtVYBIUPuS3JG+
ihZgYmVgICa+3tqavIbP2oZdXLuLAxR65mfiQHtiJwdCN3OOzyls2v0T0slQX9GV
ln6EvTk8OMIudBmkB7YiTmJF7AB+3PH/uBaiYyTKO9gtjLhnmCFvG5HxJTRFOKvU
F4oVWZJDEcqfZvYgWg8i5vgokMP41nzLfBr7j5ifUX1f3xwCHy/Tpw==
=S4XI
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-29oct19' of git://git.denx.de/u-boot-dm
- Fix for patman with email addresses containing commas
- Bootstage improvements for TPL, SPL
- Various sandbox and dm improvements and fixes
For some controllers PHYs can be optional. Handling NULL pointers without
crashing nor failing, makes it easy to handle optional PHYs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Change the stack-allocated buffer for the identification command
to explicitly allocate page-aligned buffers. Even though the spec
seems to allow having admin queue commands on non page-aligned
buffers, it seems to not be possible on my i.MX8MQ board with a
a Silicon Power P34A80. Since all of the NVMe drivers I have seen
always do admin commands on a page-aligned buffer, which does work
on my system, it makes sense for us to do that as well.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It's possible that the data cache for the buffer still holds data
to be flushed to memory, since the buffer was probably used as stack
before. Thus we need to make sure to flush it also on reads, since
it's possible that the cache is automatically flused to memory after
the NVMe DMA transfer happened, thus overwriting the NVMe transfer's
data. Also add a missing dcache flush for the prp list.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Profiling the EHCI driver shows a significant performance problem in
ehci_submit_async(). Specifically, this function keeps enabling and
disabling async schedule back and forth for every single transaction.
However, enabling/disabling the async schedule does not take effect
immediatelly, but instead may take up to 1 mS (8 uFrames) to complete.
This impacts USB storage significantly, esp. since the recent reduction
of maximum transfer size to support more USB storage devices. This in
turn results in sharp increase in the number of ehci_submit_async()
calls. Since one USB storage BBB transfer does three such calls and
the maximum transfer size is 120 kiB, the overhead is 6 mS per 120 kiB,
which is unacceptable.
However, this overhead can be removed simply by keeping the async
schedule running. Specifically, the first transfer starts the async
schedule and then each and every subsequent transfer only adds a new
QH into that schedule, waits until the QH is completed and does NOT
disable the async schedule. The async schedule is stopped only by
shutting down the controller, which must happen before moving out
of U-Boot, otherwise the controller will corrupt memory.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Add weak callback to allow board specific behavior
- flush
- initiated
This patch prepare usage of DFU back end for communication with
STM32CubeProgrammer on stm32mp1 platform with stm32prog command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a virtual DFU backend to allow board specific read and write
(for OTP update for example).
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the support of MTD partition for the MTD backend.
The expected dfu_alt_info for one alternate on the mtd device :
<name> part <part_id>
<name> partubi <part_id>
"partubi" also erase up to the end of the partition after write operation.
For example: dfu_alt_info = "spl part 1;u-boot part 2; UBI partubi 3"
U-Boot> dfu 0 mtd nand0
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add DFU backend for MTD device: allow to read
and write on all MTD device (NAND, SPI-NOR,
SPI-NAND,...)
For example :
> set dfu_alt_info "nand_raw raw 0x0 0x100000"
> dfu 0 mtd nand0
This MTD backend provides the same level than dfu nand
backend for NAND and dfu sf backend for SPI-NOR;
So it can replace booth of them but it also
add support of spi-nand.
> set dfu_alt_info "nand_raw raw 0x0 0x100000"
> dfu 0 mtd spi-nand0
The backend code is based on the "mtd" command
introduced by commit 5db66b3aee ("cmd: mtd:
add 'mtd' command")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch allows the DFU backend to indicate that that it can't
provide no more data to fill the DFU buffer, by setting b_left =0
without error, even if the size of received data is lower of the
expected total size indicated by get_medium_size.
For USB DFU stack point of view, it is acceptable:
the read length < requested size in DFU_UPLOAD and the
transaction is stopped.
That avoid infinite loop issue in dfu_read_buffer_fill because the
size for the DFU read is limited by get_medium_size = r_left
and the DFU stack expects that read is allowed up to this size.
This issue never occurs for current flash device (where chunk are
always completely read, and b_left will be never 0) but it is useful for
virtual partition when the backend only know the max size of this
alternate, the real size of the data are only known in the read
treatment.
PS: for file access on mmc, EOF is never reached as
dfu_get_medium_size_mmc returns the exact size of the file.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of DFU for several interface/device
with one command.
The format for "dfu_alt_info" in this case is :
- <interface> <dev>'='alternate list (';' separated)
- each interface is separated by '&'
The previous behavior is always supported.
One example for NOR (bootloaders) + NAND (rootfs in UBI):
U-Boot> env set dfu_alt_info \
"sf 0:0:10000000:0=spl part 0 1;u-boot part 0 2; \
u-boot-env part 0 3&nand 0=UBI partubi 0,3"
U-Boot> dfu 0 list
DFU alt settings list:
dev: SF alt: 0 name: spl layout: RAW_ADDR
dev: SF alt: 1 name: ssbl layout: RAW_ADDR
dev: SF alt: 2 name: u-boot-env layout: RAW_ADDR
dev: NAND alt: 3 name: UBI layout: RAW_ADDR
U-Boot> dfu 0
$> dfu-util -l
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=3, name="UBI", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=2, name="u-boot-env", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=1, name="u-boot", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=0, name="spl", serial="002700333338511934383330"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Copy the partition support from NAND backend to SF,
support part and partubi option.
In case of ubi partition, erase the rest of the
partition as it is mandatory for UBI.
The added code is under compilation flag CONFIG_DFU_SF_PART
activated by default.
for example:
U-Boot> env set dfu_alt_info "spl part 0 1;\
u-boot part 0 2;u-boot-env part 0 3;UBI partubi 0 4"
U-Boot> dfu 0 sf 0:0:10000000:0
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Calling cache flush on invalid buffer, even with zero length might cause
an exception on certain platforms.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Add possibility to define a part of partition as a separate DFU entity.
This allows to have more than one items on the given partition.
The real use case for this option is TM2 board. It can use u-boot stored
as Linux kernel on the defined partition (as RAW data) and load the real
kernel from the same partition, but stored under the certain offset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This is needed to make Windows THOR flash tool happy, because it
starts sending data only when interrupt packet is received on the 3rd
endpoint.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
In combination with multiple partitions in NAND, this printf() ends up
being more noise than helpful. Change it to debug() instead.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Lukasz Majewski <lukma@denx.de>
Some boards don't populate clk/reset entries as these are are optional
as per binding documentation. Therefore, don't fail driver probe if
clk/reset entries are absent in DT.
This fixes fastboot failures seen due to enabling of CONFIG_CLK on AM57xx
Fixes: e8e683d33b ("board: ti: am57xx-idk: Configure the CDCE913 clock synthesizer")
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
_gpio_direction_output function currently calls gpio_set_value
with the wrong gpio number. gpio_set_value in the uclass driver
expects a different gpio number and the _gpio_direction_output
is currently providing the number specific to the bank.
Hence fix it by calling the _gpio_set_value function instead.
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Fixes: 8e51c0f254 ("dm: gpio: Add DM compatibility to GPIO driver for Davinci")
Signed-off-by: Keerthy <j-keerthy@ti.com>
- Add I2C clocks for i.MX6Q CCF driver
- Fix check in clk_set_default_parents()
- Managed API to get clock from device tree
- Fixes for core clock code (including sandbox regression tests)
The ext4 file system requires log2blksz to be set. So when setting the
block size on the block descriptor we should fill this field too.
This fixes a problem with EFI block devices providing ext4 partitions, cf.
https://lists.denx.de/pipermail/u-boot/2019-October/387702.html.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
A previous patch below adding DDR mode support was actually for i.MX
platforms. Now i.MX eSDHC driver is fsl_esdhc_imx.c. For QorIQ eSDHC,
it uses different process for DDR mode, and hasn't been supported.
Let's drop DDR support code for i.MX in fsl_esdhc driver.
0e1bf61 mmc: fsl_esdhc: Add support for DDR mode
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
U-boot prefers DM_MMC + BLK for MMC. Now eSDHC driver has already
support it, so let's force to use it.
- Drop non-BLK support for DM_MMC introduced by below patch.
66fa035 mmc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled
- Support only DM_MMC + BLK (assuming BLK is always enabled for DM_MMC).
- Use DM_MMC instead of BLK for conditional compile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Use log() insted of debug() for uclass_find_device_by_seq function,
since this print is very much and we can filter it out with log()
interface.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move #define to top of file as per docs:
Signed-off-by: Simon Glass <sjg@chromium.org>
This function assumes that the 'val' parameter has no masked bits set.
This is not defined by the function prototype though. Fix the function to
mask the value and update the documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
-----BEGIN PGP SIGNATURE-----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=6G/J
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
The J721E DDR subsystem comprises DDR controller, DDR PHY and wrapper
logic to integrate these blocks in the device. The DDR subsystem is
used to provide an interface to external SDRAM devices which can be
utilized for storing program or data. Introduce support for the
DDR controller and DDR phy within the DDR subsystem.
Signed-off-by: Kevin Scholz <k-scholz@ti.com
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Added the following registers to the DDR configuration:
- ACIOCR0,
- ACIOCR3,
- V2H_CTL_REG,
- DX8SLxDQSCTL.
Modified enable_dqs_pd and disable_dqs_pd to only touch the associated
bit fields for pullup and pulldown registers (to preserve slew rate and
other bits in that same register). Also update the dts files in the same
patch to maintain git bisectability.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Added training support for LPDDR4 and DDR3L DDRs. Also added/changed
some register configuration to support all 3 DDR types
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdspnqAAoJEB6zHgIOrC/Ixi4IAJEEiCZPu6Z3fbkFX/Um7vCX
eMTltJN8nz4oiSi3xdx3ejueqWdW3F8VuCkHb0j0bVAhMlUlVgwCzfd0cD+D2iwS
jkrgzASNAr+JeYKYEdWqqfaUxOCd2qfuBu9EXlpvKQLWLt+KRfsOsHWcgR4bf095
aGCihvd/fKhKYUvbf5cEQnsWa3UwtsKk4Web5MKjxXx3p0iVNlu4KLd/vDWfTios
X1NqiO5ZjXNrDxyG6Aj8lgDXlE5kfeKaN/aCJU1/0U2cXm8JRu2w2dv1P/e/kU+j
NHIGzICAG4Lk/4gQTeuohJxLyvj7K3i1H12ik9Qeh4H1/5fsyybyltGUo7H443s=
=JYe3
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features and fixes for 2020.01 cycle
This feature set includes Eugen's work on a new tiny flexcom driver and
eeprom mac retrieval for the sam9x60-ek board.
This patch adds a dts property cd-active-high for builtin-cd mode to make
it configurable instead of using hardcoded active-low.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch add support for mt7628-eth to isolate LAN/WAN ports mainly to
prevent LAN devices from getting IP address from WAN.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
When received a packet with an invalid length recorded in rx descriptor,
we should free this rx descriptor to allow us to continue to receive
following packets.
Without doing so, u-boot will stuck in a dead loop trying to process this
invalid rx descriptor.
This patch adds a call to mt7628_eth_free_pkt() after received an invalid
packet length.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7628 has an embedded ethernet switch (5 phy ports + 1 cpu port).
Although in IOT mode only port0 is usable, the phy0 is still connected
to the switch, not the ethernet gmac directly.
This patch rewrites it and makes it optional. It can be turned on by adding
mediatek,poll-link-phy = <?> explicitly into the eth node. By default the
driver is switch mode with all 5 phy ports working without link detection.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch removes hardcoded gpio settings as they have been replaced by
pinctrl in dts, and also replaces regmap-based phy reset with a more
generic reset controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds slew rate calibration for mt76x8-usb-phy, removes code
which belongs to mt7620, and gets rid of using syscon and regmap by using
clock driver and reset controller.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl support for mt7628, with a file for common pinmux
functions and a file for mt7628 which has additional support for pinconf.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently this driver uses a different way to implement the spi xfer,
by modifying some fields of two registers, which is incompatible with the
MTK's original SDK linux driver. This will cause the flash data being
damaged by the SDK driver.
This patch lets the mt7621_spi_set_cs() restore the original register
fields after cs deactivated.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7621 spi controller supports continuous generic half-duplex spi
transaction. There is no need to cache xfer data at all.
To achieve this goal, the OPADDR register must be used as the first data
to be sent. And follows the eight generic DIDO registers. But one thing
different between OPADDR and DIDO registers is OPADDR has a reversed byte
order.
With this patch, any amount of data can be read/written in a single xfer
function call.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch lets the spi driver to use clock provided by the clk driver
since the new clk-mt7628 driver provides accurate sys clock frequency.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a clock driver for MediaTek MT7628/7688 SoC.
It provides clock gate control as well as getting clock frequency for
CPU/SYS/XTAL and some peripherals.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds non-DM version for mtk hsuart driver and makes it
compatible with ns16550a driver in configuration.
This is needed in SPL with CONFIG_SPL_DM disabled for reducing size.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The current brcmnand driver is based on 4.18 linux kernel which uses
mtd_set_ooblayout to set ecc layout. But nand base code in u-boot is from
old kernel which does not use this new API and expect nand_chip.ecc.layout
structure to be set. This cause nand_scan_tail function running into a bug
check if the device has a different oob size than the default ones.
This patch ports the brcmstb_choose_ecc_layout function from kernel 4.6.7
that supports the ecc layout struture and replaces the mtd_set_ooblayout
method
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
This adds support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add an entry for the Adesto AT25SL321 SPI NOR chip.
This SPI NOR chip is found in the Embedded Artist i.MX7ULP COM board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.
Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).
We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.
We do this all in one patch to guarantee bisectibility.
This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
n25q* and mt25q* (both 256Mb and 512Mb) flashes support Flag status
register that indicates various errors that may be encountered during
erase/write operations. Therefore add USE_FSR flag wherever missing.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
mt25q* flashes support stateless 4 byte addressing opcodes. Add entries
for the same. These flashes have bit 6 set in 5th byte of READ ID
response when compared to n25q* variants.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Per datasheets of n25q256* and n25q512* not all variants of n25q256* and
n25q512* support 4 Byte stateless addressing opcodes. Therefore drop
SPI_NOR_4B_OPCODES flag from these entries
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Disable and free clock when remove driver.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot uses CONFIG_SPI_FLASH_USE_4K_SECTORS to enable 4K small sector
support. Use that instead of MTD_SPI_NOR_USE_4K_SECTORS.
Reported-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Use dev_err() when reporting reason for erase/write failures so that
users can be made aware of the reason for failure.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To allow SPI_FLASH_MTD being enabled separately in SPL we add a new
option. The only user currently is the stm32mp15_basic board.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
SPI_SUNXI driver is fully dm-aware and the Allwinner
architecture kconfig would have logic to enable the
DM_SPI. So, select default spi sunxi driver for
sunxi architecture.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
DM_SPI_FLASH should require spi flash interface code for dm
version, so imply SPI_FLASH core by default if any board
enabled DM_SPI_FLASH.
This overcome the explicit enablement of CONFIG_SPI_FLASH on
respective boards when DM_SPI_FLASH being used.
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
We need distinguish the following two situations in various SPI APIs:
- given chip select num is invalid
- given chip select num is valid, but no device is attached
Currently -ENODEV is returned for both cases.
For the first case, it's more reasonable to return -EINVAL instead of
-ENODEV for invalid chip select numbers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>