The multi serial support has a "ctlr" field which almost no one uses,
but everyone is forced to set to useless strings. So punt it.
Funny enough, the only code that actually reads this field (the mpc8xx
driver) has a typo where it meant to look for the SCC driver. Fix it
while converting the check to use the name field.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Rather than sticking arch/board/driver specific logic in the common
serial code, push it all out to the respective drivers. The serial
drivers declare these funcs weak so that boards can still override
things with their own definition.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Tested-by: Minkyu Kang <mk7.kang@samsung.com>
Newer SST flashes have dropped the Auto Address Increment (AAI) word
programming (WP) modes in favor of the standard page programming mode
that most flashes now support. So add a flags field to the different
flashes to support both modes with new and old styles.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Every spi flash uses the same write disable command, so unify this in
the common code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fixed commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Now that the common spi_flash structure tracks all the info that these
drivers need, kill off their local state indirection and use just what
the common code provides.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Once we add a new page_size field for write lengths, we can unify the
write methods for most of the spi flash drivers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If we don't want to build support for any partition types we can now
add #undef CONFIG_PARTITIONS in a board config file to keep this from
being compiled in. Otherwise boards assume this is compiled in by
default
Signed-off-by: Matthew McClintock <msm@freescale.com>
andes_spi is an spi interface developed by Andes Tech.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
When CONFIG_DW_SEARCH_PHY is disabled, the local phy_addr variable
never gets initialized which causes random behavior at runtime and a
gcc warning. So set it by default to the stored phy address.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Fix commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The ctrl variable is only used when autoneg support is disabled, so only
declare it under those conditions to avoid an unused variable warning.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
* 'master' of git://git.denx.de/u-boot-mmc:
mmc: rescan fails on empty slot
AT91:mmc:fix multiple read/write error
mmc: Access mode validation for eMMC cards > 2 GiB
mmc: sh_mmcif: add support for Renesas MMCIF
mmc: fix the condition for MMC version 4
MMC: add marvell sdhci driver
MMC: add sdhci generic framework
MMC: add erase function to both mmc and sd
MMC: unify mmc read and write operation
mmc: Tegra2: Enable SD/MMC driver for Seaboard and Harmony
mmc: Tegra2: SD/MMC driver for Seaboard - eMMC on SDMMC4, SDIO on SDMMC3
According to datasheet,set block count before multiple read/write.
Signed-off-by: elen.song <elen.song@atmel.com>
Acked-by: Andy Fleming <afleming@freescale.com>
This patch provides handling of the two way handshake when SEND_OP_COND
(CMD1) is send to mmc card. It is necessary to inform eMMC card if the
host can work with high capacity cards (Jedec JESD84-A441, point 7.4.3).
The extra flag MMC_MODE_HC (high capacity) is added to indicate if the
host is capable of handling the high capacity eMMC cards.
Since this change is added to the generic mmc framework, then it requires
other boards to indicate if their mmc controllers can handle high capacity
cards. As it is now - the old behaviour of the framework is preserved.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some Renesas SuperH have MMCIF module. This driver supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Fix the problem that if we use the chip of MMC version 4 and
the capacity is smaller than 2GB or equal, the mmc->capacity is
invalid. According to the JEDEC Standard, the value of ext_csd's
capacity is valid if the value is more than 2GB.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Andy Fleming <afleming@freescale.com>
This could support both armada100 and pantheon serial in the mainline,
while this driver also be tested to support upcoming mg, mmp2 and mmp3
hardware.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Nowdays, there are plenty of mmc driver in uboot adopt the sd standard
host design, aka as sdhci. It is better to centralize the common logic
together to better maintenance.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Erase is a very basic function since the begin of sd specification is
announced. Although we could write a bulk of full 0xff memory to the
range to take place of erase, it is more convenient and safe to
implement the erase function itself.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Adding support for USB host on imx25 using the internal PHY. Changing the name
of base address define for imx31 to get some unification.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Commit 359ec49319 broke support for the
Freescale DMA engine on the 83xx parts. This is due to using registers
which do not exist on 83xx. Remove the attribute register accesses from
the 83xx build.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: York Sun <yorksun@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for 16 bit NAND devices attached to the
NDFC on ppc4xx processors. Two config entries were added:
CONFIG_SYS_NDFC_16 - Setting this tells the NDFC that a
16 bit device is attached.
CONFIG_SYS_NDFC_EBC0_CFG - This is for the External Bus
Controller configuration register.
Also, a new ndfc_read_byte() function was added which does not
first convert the data to little endian.
The NAND SPL was also modified to do 16bit bad block testing
when a 16 bit chip is being used.
Signed-off-by: Alex Waterman <awaterman@dawning.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add a flag to nand_read_skip_bad() such that if true, any trailing
pages in an eraseblock whose contents are entirely 0xff will be
dropped.
The implementation is via a new drop_ffs() function which is
based on the function of the same name from the ubiformat
utility by Artem Bityutskiy.
This is as-per the reccomendations of the UBI FAQ [1]
[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_flasher_algo
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Artem Bityutskiy <dedekind1@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When specified in the flags argument of nand_write, WITH_YAFFS_OOB causes an
operation which is mutually exclusive with the 'usual' way of writing.
Add a check that client code does not specify WITH_YAFFS_OOB along with any
other flags and add a comment indicating that the WITH_YAFFS_OOB flag should
not be mixed with other flags.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
In a future commit the behaviour of nand_write_skip_bad()
will be further extended.
Convert the only flag currently passed to the nand_write_
skip_bad() function to a bitfield of only one allocated
member. This should avoid an explosion of int's at the
end of the parameter list or the ambiguous calls like
nand_write_skip_bad(info, offset, len, buf, 0, 1, 1);
nand_write_skip_bad(info, offset, len, buf, 0, 1, 0);
Instead there will be:
nand_write_skip_bad(info, offset, len, buf, WITH_YAFFS_OOB |
WITH_OTHER);
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Replace an incorrect 'read' with 'write' in a comment.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
For newer STM parts where CFI >= 1.1, there is a byte in the extended
structure that declares the flash layout type (just like the AMD parts),
so key off of that to find out when we need to reverse the geometry.
This can be seen with M29W640 parts where U-Boot does:
Bank # 1: CFI conformant FLASH (16 x 16) Size: 8 MB in 135 Sectors
AMD Standard command set, Manufacturer ID: 0x20, Device ID: 0x22ED
Erase timeout: 8192 ms, write timeout: 1 ms
Buffer write timeout: 1 ms, buffer size: 16 bytes
Sector Start Addresses:
20000000 RO 20002000 RO 20004000 RO 20006000 RO 20008000 RO
2000A000 RO 2000C000 RO 2000E000 RO 20010000 RO 20020000 RO
...
But Linux does:
physmap platform flash device: 00800000 at 20000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank.
Manufacturer ID 0x000020 Chip ID 0x0022ed
physmap-flash.0: Swapping erase regions for top-boot CFI table.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>
When dealing with non-multipoint devices, if the software root hub code
accepted the message, then we still need to process it normally. So only
return quickly when the root hub skipped the message or is otherwise in
an error state.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-arm:
run arm_pci_init after relocation
IXP42x PCI rewrite
update/fix PDNB3 board
update/fix IXDP425 / IXDPG425 boards
add dvlhost (dLAN 200 AV Wireless G) board
IXP NPE: add support for fixed-speed MII ports
update/fix AcTux4 board
update/fix AcTux3 board
update/fix AcTux2 board
update/fix AcTux1 board
use -ffunction-sections / --gc-sections on IXP42x
support CONFIG_SYS_LDSCRIPT on ARM
fix "depend" target in npe directory
Fix IXP code to work after relocation was added
trigger hardware watchdog in IXP42x serial driver
add support for IXP42x Rev. B1 and newer
add XScale sub architecture (IXP/PXA) to maintainer list
Conflicts:
arch/arm/lib/board.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
clean up IXP PCI handling: get rid of IXP-private bus scan, BAR assign etc.
code and use u-boot's PCI infrastructure instead. Move board-specific PCI
setup code (clock/reset) to board directory.
Signed-off-by: Michael Schwingen <michael@schwingen.org>
The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it. Drop it.
This includes support for VFD displays which have always been used by
this board only.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch fixes following compile warning:
---8<---
macb.c: In function 'macb_write_hwaddr':
macb.c:525:2: warning: dereferencing type-punned pointer will break strict-aliasing rules
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
This patch removes the warning
---8<---
at91_emac.c: In function 'at91emac_write_hwaddr':
at91_emac.c:487:2: warning: dereferencing type-punned pointer will break strict-aliasing rules
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
The rework effort for ATMEL (AT91/AVR32) accidentially broke build of
this driver. Fix this to make it build again. However this driver should
be reworked as soon as possible!
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
* convert at91rm9200ek and eb_cpux9k2 board to ATMEL_xxx name scheme
* Fix: timer.c compile error io.h not found with arm/at91rm9200
* update arm920t/at91 to ATMEL_xxx name scheme
* update arm920t/at91 soc lib
* update at91_emac driver
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Tested-by: Andreas Bießmann <andreas.devel@gmail.com>
The status polling can take a while, so make sure we kick the
watchdog after each successful poll.
Signed-off-by: Patrick Sestier <psestier@mircom.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This allows this configuration to be defined differently for some
boards that request it.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This patch added set_mmc_clk for external clock control.
c210 didn't support host clock control.
So We need external_clock_control function for c210.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Fix typo resulting in the compilation error
s5p_mmc.c: In function 's5p_mmc_initialize':
s5p_mmc.c:469: error: 'struct mmc' has no member named 'm_bmax'
introduced by commit "MMC: make b_max unconditional"
(8feafcc49c)
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: John Rigby <john.rigby@linaro.org>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Before the actual initialization do a hard reset of the SATA port and the
connected device.
changes v1->v2:
- add comment for udelay
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Add missing header file to fix compilation warning
omap_hsmmc.c: In function 'omap_mmc_init':
omap_hsmmc.c:474: warning: implicit declaration of function 'get_cpu_family'
omap_hsmmc.c:474: warning: implicit declaration of function 'get_cpu_rev'
introduced by commit "MMC: omap_hsmmc.c: disable
multiblock rw on old rev omap34xx silicon"
(4ca9244d74)
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: Andy Fleming <afleming@freescale.com>
CC: John Rigby <john.rigby@linaro.org>
For emmc, it may have up to 7 partitions: two boot partitions, one
user partition, one RPMB partition and four general purpose partitions.
(Refer to JESD84-A44.pdf/page 154)
As bootloader may need to read out or reflashing images on those
different partitions, it is better to enable the partition switch with
console command support.
Also for partition would be restore to user partition(part 0) when CMD0
is used, so change mmc_init routine to perform normal initialization
only once for each slot, unless use the rescan command to force init
again.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
A "send status" command is added with the commit "mmc: checking
status after commands with R1b response". But the status register
returned from send status command of SPI protocol is different from
that of MMC/SD protocol. We do a simple test and generate a response
in stead of full bit-by-bit translation.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Faraday's ftide020_s is an IDE-AHB controller for SoC design.
This patch add the u-boot driver (PIO) of ftide020 ATA (IDE) driver.
IDE commands include read, info, and other functions has been implemented.
Because this IDE controller support AHB interface only which is differ
from other most IDE controller supports PCI interface. Some registers
access is required during CMD/DATA I/O. Hence a configuration
"CONFIG_IDE_AHB" is required to be defined according to the feature in
cmd_ide.c.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
This patch adds support for the National LM64 temperature
sensor with integrated fan control to lm63.c.
Main difference between LM63 and LM64 is 16°C offset in sensor
readings.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
This is needed for the upcoming TFTP server implementation.
This also simplifies PingHandler() and fixes rxhand_f documentation.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Two new options:
CONFIG_PL011_SERIAL_RLCR
Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
have separate receive and transmit line control registers. Set
this variable to initialize the extra register.
CONFIG_PL011_SERIAL_FLUSH_ON_INIT
On some platforms (e.g. U8500) U-Boot is loaded by a second stage
boot loader that has already initialized the UART. Define this
variable to flush the UART at init time.
empty fifo on init
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Singed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For freescale i.MX53 eSDHCv2, when using CMD12, cmdtype need
to be set to ABORT, otherwise, next read command will hang.
This is a software Software Restrictions in i.MX53 reference manual:
29.7.8 Multi-block Read
For pre-defined multi-block read operation, that is,the number of blocks
to read has been defined by previous CMD23 for MMC, or pre-defined number
of blocks in CMD53 for SDIO/SDCombo,or whatever multi-block read without
abort command at card side, an abort command, either automatic or manual
CMD12/CMD52, is still required by ESDHC after the pre-defined number of
blocks are done, to drive the internal state machine to idle mode. In this
case, the card may not respond to this extra abort command and ESDHC will
get Response Timeout. It is recommended to manually send an abort command
with RSPTYP[1:0] both bits cleared.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Make existing field b_max field in struct mmc unconditional
and use it instead of CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_bread
and mmc_bwrite.
Initialize b_max to CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_register
if it has not been initialized by the hw driver.
Initialize b_max to 0 in all callers to mmc_register.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for the ARM PrimeCell MultiMedia Interface - PL180.
Ported from original device driver written by ST-Ericsson.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration. Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.
The old definition of the "monitor" environment variable only determines
which video port to use for output. This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The
resolution was hard-coded into board-specific code. The Linux command-line
arguments needed to be hard-coded to the proper video definition string.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add function video_get_video_mode(), which parses the "video-mode" environment
variable and returns each of its components. The format matches the video=
command-line option used for Linux:
video-mode=<driver>:<xres>x<yres>-<depth>@<freq><,option=string>
<driver> The video driver, ignored by U-Boot
<xres> The X resolution (in pixels) to use.
<yres> The Y resolution (in pixels) to use.
<depth> The color depth (in bits) to use.
<freq> The frequency (in Hz) to use.
<options> A comma-separated list of device-specific options
Signed-off-by: Timur Tabi <timur@freescale.com>
There seems to be tools producing incorrect 'end of bitmap data'
markers '0100' in a RLE bitmap. Drawing such bitmaps can result
in overwriting memory above the frame buffer. E.g. on MPC5121e
based boards this memory can contain U-Boot environment.
We may not rely on the correct end of bitmap data marker 0001
only, but also have to check whether we are going to draw a
valid frame buffer scan line.
The patch provides a fix by maintaining a pixel counter
which is incremented by the amount of pixels we are going
to draw. If the counter exceeds frame buffer pixels limit
we stop the drawing with the error message.
Reported-by: Michael Weiss <michael.weiss@ifm.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Anatolij Gustschin <agust@denx.de>
Deblock i2c bus when switching to another i2c bus, if using
i2c_set_bus_num().
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Move the header file and definitions of ftsmc020
static memory control unit from a320 SoC folder to
"drivers/mtd" folder.
This change will let other SoC which also use ftsmc020
could share the same header file.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
1. ftpmu010.h: fix and add definitions
Enhanced for more features and asm related support
according to datasheet.
Note:
- FTPMU010_PDLLCR0_HCLKOUTDIS is "incorrect" in datasheet.
- FTPMU010_PDLLCR0_DLLFRANG is only 1 bit at bit #19. (not 20-19)
- FTPMU010_PDLLCR0_HCLKOUTDIS is 4 bits at bit #20. (not 24-21)
2. ftpmu010.c: enhance features and fix relocation
- The following functions is added for pmu features.
ftpmu010_mfpsr_select_dev()
ftpmu010_sdramhtc_set()
- This patch also fix the declare statement for relocation.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Add the ability to support multiple i2c bus for mv_i2c
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
Add i2c_clk_enable in the cpu specific code, since previous platform it,
while new platform don't need. In the pantheon and armada100 platform,
this function is defined as NULL one.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
The original 10000 value would be 100ms, which is not
the comments said.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
For better sharing with other platform other than pxa's,
it is more convenient to put the driver to the common place.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
I ran into a problem where the reset was failing except when I enabled
debugging support. After talking with Garret Swalling at Spansion I
was told that the GL-N series of devices require a 500ns wait for the
reset to complete. The below patch adds a 1us delay after all reset
commands.
-Aaron Williams
Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The M29W800DT parts also report their geometry with the sector layout
reversed. So add that ID to the flash_fixup_stm function.
Otherwise, we get:
bfin> flinfo
Bank # 1: CFI conformant FLASH (16 x 16) Size: 1 MB in 19 Sectors
AMD Standard command set, Manufacturer ID: 0x20, Device ID: 0x22D7
Erase timeout: 8192 ms, write timeout: 1 ms
Sector Start Addresses:
20000000 20004000 20006000 20008000 20010000
20020000 20030000 20040000 20050000 20060000
20070000 20080000 20090000 200A0000 200B0000
200C0000 200D0000 200E0000 200F0000
Reported-by: Jianxi Fu <fujianxi@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
This converts tsec to use the new PHY Lib. All of the old PHY support
is ripped out. The old MDIO driver is split off, and placed in
fsl_mdio.c. The initialization is modified to initialize the MDIO
driver as well. The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
The tsec driver had a bunch of PHY drivers already written. This
converts them all into PHY Lib drivers, and serves as the first
set of PHY drivers for PHY Lib.
While doing that, cleaned up a number of magic numbers (though
not all of them, as PHY vendors like to keep their numbers as
magical as possible). Also, noticed that almost all of the
vitesse/cicada PHYs had the same config/parse/startup functions,
so those have been collapsed into one.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme. The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support
The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).
The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.
We now have MDIO drivers and PHY drivers
An MDIO driver provides:
read
write
reset
A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed
The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()
Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)
We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.
We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,
we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.
Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
There were a few files which were already using phy_read and phy_write
for their PHY function names. It's only a few places, and the name
seems most appropriate for the high-level abstraction, so let's
rename the other versions to something more specific.
Also, uec_phy.c had a marvell_init function which I renamed to not
conflict with the one in marvell.c
Lastly, uec_phy.c was putting a space between the phy writing
function names, and the open paren, so I fixed that
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
This is merely a rearrangement. No changes to the code, except
to remove now-useless declarations.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
This patch sync with Brian's patch on Linux in nand_flash_detect_onfi()
commit b7b1a29d94c17e4341856381bccb4d17495bea60
Author: Brian Norris <computersforpeace@gmail.com>
Date: Sun Dec 12 00:23:33 2010 -0800
mtd: nand: rearrange ONFI revision checking, add ONFI 2.3
In checking for the ONFI revision, the first conditional (for checking
"unsupported" ONFI) seems unnecessary. All ONFI revisions should be
backwards-compatible; even if this is not the case on some newer ONFI
revision, it should simply fail the second version-checking if-else block
(i.e., the bit-fields for 1.0, 2.0, etc. would not be set to 1). Thus, we
move our "unsupported" condition after having checked each bit field.
Also, it's simple enough to add a condition for ONFI revision 2.3. Note
that this does *NOT* mean we handle all new features of ONFI versions
above 1.0.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
This patch sync with David's patch on Linux in nand_flash_detect_onfi()
commit 4ccb3b4497ce01fab4933704fe21581e30fda1a5
Author: David Woodhouse <David.Woodhouse@intel.com>
Date: Fri Dec 3 16:36:34 2010 +0000
mtd: nand: Fix integer overflow in ONFI detection of chips >= 4GiB
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
The omap24xx driver only seems to support devices that have a single subaddress
byte. With these types of devices, the first access in a bus transaction is
usually a write (writes the subaddress) followed by either a read or write to
access the devices registers.
Many such devices will respond to a read as the first access, but there are at
least some that will NACK such a read. (e.g. ADV7180.)
The probe function attempts to detect a devices ACK to a read access only and
fails to find devices that NACK a read.
This commit modifies the probe function to start a write instead. This detects
devices that respond to reads (since they must also respond to writes) as well
as those that only respond to writes. The bus is immediately set to idle after a
(N)ACK avoiding actually writing anything to the device.
Signed-off-by: Nick Thompson <nick.thompson@ge.com>
Commit 6ee1416e81 (mtd, cfi: introduce
void flash_protect_default(void)) introduced a bug which resulted in
boards that define CONFIG_SYS_FLASH_AUTOPROTECT_LIST not compiling with
the the following errors and warning:
ptyser@petert u-boot $ make -s xpedite520x
Configuring for xpedite520x board...
cfi_flash.c: In function 'flash_protect_default':
cfi_flash.c:2118: error: 'i' undeclared (first use in this function)
cfi_flash.c:2118: error: (Each undeclared identifier is reported only once
cfi_flash.c:2118: error: for each function it appears in.)
cfi_flash.c:2118: error: 'apl' undeclared (first use in this function)
cfi_flash.c:2118: error: invalid application of 'sizeof' to incomplete type 'struct apl_s'
cfi_flash.c: In function 'flash_init':
cfi_flash.c:2137: warning: unused variable 'apl'
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reported-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Heiko Schocher <hs@denx.de>
Hi Terry,
> So I guess:
> mmc_init calls mmc_send_op_cond that set high_capacity,
> than it calls mmc_startup, that, with MMC_CMD_SEND_CSD command, set
> the capacity, using values in CSD register.
> So I guess that mmc_change_freq should not recalculate high_capacity.
>
> It seems better, isn't it?
>
> Regards,
> Raffaele
>
Finally I think that it is enough to apply the following patch in order
to fix the issue.
Regards,
Raffaele
Signed-off-by: Andy Fleming <afleming@freescale.com>
Defining CONFIG_MMC_TRACE in the include board file it is possible to activate
a tracing support.
This code helps in case of eMMC hw failure or to investigate possible eMMC
initialization issues.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The first SEND_OP_COND (CMD1) command added is used to ask card capabilities.
After it an AND operation is done between card capabilities and host
capabilities (at the moment only for the voltage field).
Finally the correct value is sent to the MMC, waiting that the card
exits from busy state.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
It is recommended to check card status after these kind of commands.
This is done using CMD13 (SEND_STATUS) JEDEC command until
the card is ready.
In case of error the card status field is displayed.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports multi
blocks read/write.
The crc checksum on data packet is enabled with the def,
There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Andy Fleming <afleming@freescale.com>
These local vars need not be writable nor exported.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
As DATA_ERROR includes the value IRQSTAT_DTOE, a timeout error
would yield the first error return instead of TIMEOUT.
By swapping the test TIMEOUTs are reported as such
An alternate solution would be to remove the IRQSTAT_DTOE from the DATA_ERROR define
but as that one might be less desired I've opted for the simplest solution
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch adds CONFIG_SPI_IDLE_VAL to cf_spi.c
The default setting is 0x0 to behave same as current version, in case
CONFIG_SPI_MMC is set, the value is set to 0xFFFF (all ones). In either
case, the value can be overwritten by board configuration.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The maximum blocks value was hardcoded to 65535 due to a 16 bit
register length. The value can change for different platforms.
This patch makes the default the current value of 65535, but it
is configurable for other platforms.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. Move header to include/faraday
2. Fix include path in ftwdt010_wdt.c
3. Fix function prototype and declaration to
- ftwdt010_wdt_settimeout
- ftwdt010_wdt_reset
- ftwdt010_wdt_disable
4. Add "#if definde (CONFIG_HW_WATCHDOG)" let user have flexibilty
to choose which better to his product.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
This patch adds a new member to struct spi_flash (u16 sector_size)
and updates the spi flash drivers to start populating it.
This parameter can be used by spi flash commands that need to round
up units of operation to the flash's sector_size.
Having this number in one place also allows duplicated code to be
further collapsed into one common location (such as erase parameter
and the detected message).
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The AT45 flashes are completely different (at the command set and
status register level) from all other SPI flashes, so we can't unify
their logic with common code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Faraday ftwdt010 watchdog is an architecture independant
watchdog. It is usually used in SoC chip design.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add Intel E1000 82574L PCIe card support. Test on MPC8544DS
and MPC8572 board.
Add the missing contact information for future support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes ea20 after 8ef583a035 where
the u-boot custom PHY_ macros were replaced with those of linux/mii.h MII_
definitions except in the RMII support for davinci_emac. Probably also due to
the merge path of changes in 2010.12.
Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca>
CC: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
All of the spi flash drivers implement the status register polling for
detecting the device ready state, so unify them all in a new helper
function -- spi_flash_wait_ready.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark
level register description has been changed:
9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00
25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Don't forget to count full data size for the multiblock operation request.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The timer register is 32bits, not 16bit, so 0xFFFF won't fill it.
Write out -1 to make sure to fill the whole thing.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
collect code which protects default sectors in a function, called
flash_protect_default. So boardspecific code can call it too.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
P1021 has some QE pins which need to be set in pmuxcr register before
using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and
UCC5 in Eth mode. QE9 and QE12 are set for MII management. QE12 needs to
be released after MII access because QE12 pin is muxed with LBCTL signal.
Also added relevant QE support defines unique to P1021.
The P1021 QE is shared on P1012, P1016, and P1025.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ULI1575 EHCI controller to the list of the supported devices.
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If some pre-boot or earlier stage bootloader (NAND SPL) has setup LAW
entries consider them good and mark them used.
In the NAND SPL case we skip re-initializing based on the law_table
since the SPL phase already did that.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL PCIe controller v2.1:
- New MSI inbound window
- Same Inbound windows address as PCIe controller v1.x
Added new pit_t member(pmit) to struct ccsr_pci for MSI inbound window
FSL PCIe controller v2.2 and v2.3:
- Different addresses for PCIe inbound window 3,2,1
- Exposed PCIe inbound window 0
- New PCIe interrupt status register
Added new Interrupt Status register to struct ccsr_pci & updated pit_t array
size to reflect the 4 inbound windows.
To maintain backward compatiblilty, on V2.2 or greater controllers we
start with inbound window 1 and leave inbound 0 with its default value
(which maps to CCSRBAR).
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the PI7C9X442SL PCIe EHCI host controller
from Pericom.
Tested at P4080DS eval board from Freescale.
Signed-off-by: Ralf Trübenbach <ralf.truebenbach@men.de>
Cc: Remy Bohmer <linux@bohmer.net>
The anomaly workarounds we need for older silicon might break things
if used on newer versions where the anomalies don't exist. So check
the silicon rev at runtime too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If NCE is hooked up to NCS3, we don't need to (and can't)
explicitly set the state of the NCE pin. Instead, the
controller asserts it automatically as part of a
command/data access. Only "CE don't care"-type NAND chips
can be used in this manner.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
This patch adds support for reading an ONFI page parameter from a NAND
device supporting it. If this is the case, struct nand_chip onfi_version
member contains the supported ONFI version, 0 otherwise.
This allows NAND drivers past nand_scan_ident to set the best timings for the
NAND chip.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The P1011, P1012, P1015, P1016, P1020, P1021, P1024, & P1025 SoCs require
that we initialize the SERDES registers if the lanes are configured for
PCIe. Additionally these devices PCIe controller do not support ASPM
and we have to explicitly disable it.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The function find_sector() does not take into account if the flash bank
has changed since the last call. This could lead to illegal accesses inside
and beyond the flash_info_t info strcture. For example if the current
flash bank has less sectors than the last used flash bank.
This patch adds two cheks. One that insures, that the current sector does
not exceed the allowed maximum (which is always a good idea). And one that
checks if the current access is to the same flash bank as the last access.
If not, the search loop will start with sector 0.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Blocksize was hardcoded to 512 bytes. But the blocksize varies
depeding on various mmc subsystem commands (between 8 and 512).
This hardcoding was resulting in interrupt error during data
transfer.
It is now calculated based upon the request sent by mmc subsystem.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use get_timer() the same way as drivers/net/ftgmac100.c
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Reviewed-by: Macpaul Lin <macpaul@gmail.com>
Tested-by: Macpaul Lin <macpaul@gmail.com>
- Timeout counter value is set as DTOCV bits in SYSCTL register
For counter value set as timeout,
Timeout period = (2^(timeout + 13)) SD Clock cycles
- As per 4.6.2.2 section of SD Card specification v2.00, host should
cofigure timeout period value to minimum 0.25 sec.
- Number of SD Clock cycles for 0.25sec should be minimum
(SD Clock/sec * 0.25 sec) SD Clock cycles
= (mmc->tran_speed * 1/4) SD Clock cycles
- Calculating timeout based on
(2^(timeout + 13)) >= mmc->tran_speed * 1/4
Taking log2 both the sides and rounding up to next power of 2
=> timeout + 13 = log2(mmc->tran_speed/4) + 1
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We had an extra '0x' in the output of the LAWAR header that would cause
output like:
LAWBAR11: 0x00000000 LAWAR0x11: 0x80f0001d
intead of:
LAWBAR11: 0x00000000 LAWAR11: 0x80f0001d
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add waiting for receiving Ethernet gadget state on the Windows host
side before dropping pullup, but keep it for debug.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Port USB gadget RNDIS protocol support from linux-2.6.26
(.27 gadget stack actually has composite drivers).
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Disconnecting USB gadget with pending interrupt may cause its wrong
handling in the next time when interface will be started again
(especially actual for RNDIS). This interrupt may force the gadget
to queue unexpected response before setup stage.
Despite the fact that such interrupt handled after dropped pullup
also may add pending response, this will not bring to any issues due to
usb_ep_disable (which clears the queue) called on gadget unregistering.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
This adds support for using USB Ethernet dongles in host mode. This is just
the framework - drivers will come later. A new config option called
CONFIG_USB_HOST_ETHER can be defined in board config files to switch this
on.
The was originally written by NVIDIA and was cleaned up for release by the
Chromium authors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Changed both to use a common timeout for URB submission, since they were using
different values and EHCI's was too short.
Also fixed EHCI to actually check if urb submission succeeded, rather than
silently continuing into the weeds.
Change-Id: I7f71499ffaa05187d8e5618db2419e1606007b82
Signed-off-by: Simon Glass <sjg@chromium.org>
Added this for mmc_spi driver. Though altera spi core does not
support programmable speed. It is fixed when configured in
sopc-builder.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some CPU needs cache handling. So this patch add the config of
CONFIG_SH_ETHER_CACHE_WRITEBACK, and it calls wback function.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Added arch/arm/cpu/arm926ejs/davinci/et1011c.c for handling
ET1011C gigabit phy. which overrides get_link_speed function
from default implementation. This enables output of 125 MHz
reference clock on SYS_CLK pin.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Adds "DaVinci-EMAC" as the name of the device so that
it gets printed as "Using DaVinci-EMAC device"
during network access (dhcp, tftp) instead of empty name
in "Using" statement.This name also gets
reflected in 'ethact' env variable.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Enabling the gigabit was overwriting the
previous configuration by setting up only GIGAFORCE and
GIG bits of MAC control register.
Modified to retain previous configuration while
gigabit enabling.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Added support for MMC/SD cards for Davinci. This feature is enabled by
CONFIG_DAVINCI_MMC and is dependant on CONFIG_MMC and CONFIG_GENERIC_MMC
options. This is tested on DM355 and DM365 EVMs with both the available mmc
controllers.
Signed-off-by: Alagu Sankar <alagusankar@embwise.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Drop warnings due to unused variables.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This patch cleans driver code replacing all accesses
to registers with fixed offsets with a corresponding
structure.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The MXC SPI driver didn't calculate the SPI clock up to
now and just used highest possible divider 512 for DATA
RATE in the control register. This results in very low
transfer rates.
The patch adds code to calculate and setup the SPI clock
frequency for transfers.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Stefano Babic <sbabic@denx.de>
We need to shift only one time in each cycle in the swapping loop
for unaligned tx case. Currently two byte shift operations are
performed in each loop cycle causing zero gaps in the transmited
data, so not all data scheduled for transmition is actually
transmited.
The proper swapping in unaligned rx case is missing, so add it
as we need to put the received data into the rx buffer in the
correct byte order.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
The patch adds helper funtions for basic access to the registers
of the MC9sdz60 chip (multifunctional device with RTC and CAN) via
I2C interface.
Signed-off-by: Stefano Babic <sbabic@denx.de>
There is sporadic failures when more as one I2C slave
is on the bus and the processor tries to communicate
with more as one slave.
The problem was seen on a mx35pdk (two I2C slaves,
PMIC controller and CAN/RTC chip).
The current driver uses the IIF bit in the status register
to check if the bus is busy or not. According to the manual,
this is not correct, because the IIB bit should be checked.
Not only, to check if a transfer is finished must be checked
the ICF bit, and this is not tested at all.
This patch comes from analyse with a corresponding driver
provided by Freescale as part of the LTIB tool. Comparing
the two drivers, it appears that the current u-boot driver checks
the wrong bits, and depending on race condition, the transfer
can be successful or not.
The patch gets rid also of own debug function (DPRINTF),
replaced with the general debug().
Tested on Freescale mx35pdk.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This driver accesses to processor's register
via __REG macros, that are removed (or are planned
to be removed) and replaced by C structures.
This patches replaces all occurrencies of __REG macros.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Make at91 header includes in soft_i2c depend only on CONFIG_AT91FAMILY
rather than individual SoCs.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Reinhard Meyer<u-boot@emk-elektronik.de>
Faraday's ftpmu010 is a power managemnet unit which support cpu
sleep and frequency scaling. It has been integrated into many SoC.
This patch also move ftpmu010 to a proper place for later enhancement.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Patch 8ef583a0 [miiphy: convert to linux/mii.h] introduced the following
compiler warnings in the uec ethernet driver:
In file included from /local/home/galak/git/u-boot-85xx/include/miiphy.h:37:0,
from uec.c:32:
/local/home/galak/git/u-boot-85xx/include/linux/mii.h:133:0: warning: "LPA_1000FULL" redefined
uec_phy.h:34:0: note: this is the location of the previous definition
/local/home/galak/git/u-boot-85xx/include/linux/mii.h:134:0: warning: "LPA_1000HALF" redefined
uec_phy.h:35:0: note: this is the location of the previous definition
In file included from /local/home/galak/git/u-boot-85xx/include/miiphy.h:37:0,
from uec_phy.c:27:
/local/home/galak/git/u-boot-85xx/include/linux/mii.h:133:0: warning: "LPA_1000FULL" redefined
uec_phy.h:34:0: note: this is the location of the previous definition
/local/home/galak/git/u-boot-85xx/include/linux/mii.h:134:0: warning: "LPA_1000HALF" redefined
uec_phy.h:35:0: note: this is the location of the previous definition
Fix them be removing the duplication in the uec code and utlizing the
linux/mii.h version instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.
Eventually this should be handled by Kconfig & defconfigs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Add P2040 SoC specific information:
* SERDES Table
* Added p2040 to cpu_type_list and SVR list
* Added number of LAWs for p2040
* Set CONFIG_MAX_CPUS to 4 for p2040
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1014 is similar to the P1010 processor with the following differences:
- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
* TCP/IP acceleration and classification capabilities
* IEEE 1588 support
* Lossless flow control
* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
software watchdog timer, and four general-purpose timers
* Dual DUARTs
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Calling eth_bind at usb_eth_init time causes renaming of the network
device from 'usb_ether' to 'usb0'. Fixing this to keep the first name.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Since the ether may not be the only one usb gadget would be used
in the uboot, it is neccessary to do the register each time the
eth begin to work to make usb gadget driver less confussed when
we want to use two different usb gadget at the same time.
Usb gadget driver could simple ignore the register operation, if
it find the driver has been registered already.
Signed-off-by: Lei Wen <leiwen@marvell.com>
There's no compelling reason to have the output on bootup or the
"flinfo" command print "flash" in uppercase, so use the proper case
where appropriate.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The default value of the SRS, VS18 and VS30 and ADMAS fields in the host
controller capabilities register (HOSTCAPBLT) are incorrect. The default
of these bits should be zero instead of one.
Clear these bits out when we read HOSTCAPBLT.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Do not issue a manual asynchronous CMD12. Instead, use a (software)
synchronous CMD12 or AUTOCMD12 to abort data transfer.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This change does the following:
- Adds printing of negotiated link width. This information can be
useful when debugging PCIe issues.
- Makes it optional for boards to implement board_serdes_name().
Previously boards that did not implement it would print unsightly
output such as "PCIE1: Connected to <NULL>..."
- Rewords the PCIe boot output to reduce line length and to make it
clear that the "base address XYZ" value refers to the base address of
the internal processor PCIe registers and not a standard PCI BAR
value.
- Changes "PCIE" output to the standard "PCIe"
Before change:
PCIE1: connected to <NULL> as Root Complex (base addr ef008000)
01:00.0 - 10b5:8518 - Bridge device
02:01.0 - 10b5:8518 - Bridge device
02:02.0 - 10b5:8518 - Bridge device
02:03.0 - 10b5:8518 - Bridge device
PCIE1: Bus 00 - 05
PCIE2: connected to <NULL> as Endpoint (base addr ef009000)
PCIE2: Bus 06 - 06
After change:
PCIe1: Root Complex of PEX8518 Switch, x4, regs @ 0xef008000
01:00.0 - 10b5:8518 - Bridge device
02:01.0 - 10b5:8518 - Bridge device
02:02.0 - 10b5:8518 - Bridge device
02:03.0 - 10b5:8518 - Bridge device
PCIe1: Bus 00 - 05
PCIe2: Endpoint of VPX Fabric A, x2, regs @ 0xef009000
PCIe2: Bus 06 - 06
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since all the PCIe controllers are connected over SERDES on the SoCs we
can utilize is_serdes_configured() to determine if a controller is
enabled. After which we can setup the ATMUs and LAWs for the controller
in a common fashion and allow board code to specify what the controller
is connected to for reporting reasons.
We also provide a per controller (rather than all) for some systems that
may have special requirements.
Finally, we refactor the code used by the P1022DS to utilize the new
generic code.
Based on patch by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously we passed in a specifically named struct pci_controller to
determine if we had setup the particular PCI bus. Now we can search for
the struct so we dont have to depend on the name or the struct being
statically allocated.
Introduced new find_hose_by_cfg_addr() to get back a pci_controller struct
back by searching for it means we can do things like dynamically allocate
them or not have to expose the static structures to all users.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Some new platform's esdhc pins don't share with other function.
The eSDHC shouldn't be disabled, even if "esdhc" isn't defined
in hwconfig env variable.
Use CONFIG_FSL_ESDHC_PIN_MUX to fix this problem.
Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch sync with David's patch on Linux for handling nand_scan_ident.
commit 5e81e88a4c140586d9212999cea683bcd66a15c6
Author: David Woodhouse <David.Woodhouse@intel.com>
Date: Fri Feb 26 18:32:56 2010 +0000
mtd: nand: Allow caller to pass alternative ID table to nand_scan_ident()
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
This patch add addition suffix to nand write to give the uboot
the power to directly burn the yaffs image to nand.
Signed-off-by: Lei Wen <leiwen@marvell.com>
The eth_device.name field length is limited by NAMESIZE,
which is 16 defined in include/net.h. Unfortunately, two
of the names in lan91c96.c are beyond that.
Signed-off-by: YanJun Yang <yangyj.ee@gmail.com>
This adds support for for the PCA9535/PCA9539 family of gpio devices which
have 16 output pins.
To let the driver know which devices are 16-pin it is necessary to define
CONFIG_SYS_I2C_PCA953X_WIDTH in your board config file. This is used to
create an array of {chip, ngpio} tuples that are used to determine the
width of a particular chip. For backwards compatibility it is assumed that
any chip not defined in CONFIG_SYS_I2C_PCA953X_WIDTH has 8 pins.
Acked-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>