Commit Graph

109 Commits

Author SHA1 Message Date
Ashok Reddy Soma
702de89cc6 treewide: mem: Move mtest related defines to Kconfig
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-08 12:02:56 -04:00
Miquel Raynal
88718be300 mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND
Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Adam Ford
97605d3ca3 ARM: omap3_logic: Fix SPL boot failure when EHCI enabled
Some of the USB code is still being built into SPL even when the
SPL menu options have it explicitly disabled for SPL. Unit there is
a better solution, This patch undefines CONFIG_USB_EHCI_OMAP when
building SPL which reduces the code and lets the board boot again.

Fixes: 25e4ff45b1 ("ARM: omap3_logic: Enable OMAP EHCI support
for SOM-LV Boards")

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-26 11:46:27 -04:00
Simon Glass
37304aaf60 Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig
This converts the following to Kconfig:
   CONFIG_USE_PREBOOT
   CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-02 11:19:14 -04:00
Simon Glass
b06da06dd4 Add CONFIG_USE_PREBOOT to boards that use CONFIG_PREBOOT
In order to use CONFIG_PREBOOT with Kconfig, CONFIG_USE_PREBOOT must be
defined for each board. To prepare for conversion to Kconfig, add this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-02 11:17:58 -04:00
Adam Ford
25e4ff45b1 ARM: omap3_logic: Enable OMAP EHCI support for SOM-LV Boards
The SOM-LV boards support the OMAP EHCI driver using port 2.
With the driver updated to support device tree, this patch sets
the corresponding pin muxing for the tranceiver as well as the
reset pin.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-27 13:36:52 -04:00
Markus Klotzbuecher
a9221f3ebd at91, omap2plus: configs: migrate CONFIG_ENV_ to defconfigs
Enable the extended ENV options for AT91 and OMAP2PLUS in order to be
able to use CONFIG_ENV_UBI_* on these architectures.

As this change also makes the configs ENV_SIZE, ENV_SECT_SIZE,
ENV_OFFSET visible to AT91 and OMAP2PLUS, migrate users of these to
KConfig.

This migration was run using an extended moveconfig.py which evaluates
expressions such as "(512 << 10)". See patch ("moveconfig: expand
simple expressions").

All modified boards were built with SOURCE_DATE_EPOCH=0 before and
after the change and successfully confirmed that the identical binary
is generated (the only exception was igep00x0, which does not define
CONFIG_ENV_IS_IN_UBI in the original board header. Once that is
defined, the test passes too).

hs: rebased patch to:
  68b90e57bc: "configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT"

Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Tom Rini <trini@konsulko.com>
2019-07-09 07:00:21 +02:00
Tom Rini
b4ee6daad7 Porting to DM and i.MX8
------------------------
 
 - warp7 to DM
 - kp_imx53 to DM
 - Warnings in DT
 - MX8QM support
 - colibri-imx6ull to DM
 - imx7d-pico to DM
 - ocotp for MX8
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlzDBtoPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3UpQL/ipaUejQOOr00oOgUBQqt3JCPZ7KNu8ruih/
 nIFUDrI8nP+4psaOhRp1sEPFJUxUjdIqODeAZD8zrlEi1pXNAgPWYrFRfbz54bzw
 jLsqqMz1/djQseLydQTcqZTSz8Ys7o+8OfKH64fdsZn+y9no9tHBN5hz5qWdXexN
 kbyykkg8TJC3eUyRZqKuULOqzDV9BAdASOXu7UTa04sEekLdVvS2+zkUdB6UVZTN
 LOAzm+7xY8Tey1BZxLuZUJDpHzFEMvPvlbbQRrxeDn/feZJwNgIP6hGcMeVOwOIf
 KEwFn/m/HI2JWS4taXb5aT+v3xmiQvyCC3jNW0XTf5rq02pbfgyPsVhGQIGyU2yY
 Fj7zIN7hVCLJNBpctvXyuAd1MjOlGEPIrHNjRnIZjtr7/iA1AIRn7Hg4cGNCHw6V
 5gdza3B/xFODN+Ts6O+UVIukI61MJ6mGGdNCueOnWDviNROOL82D7Jh02KfNNNxR
 q+yPsHSpo6rC1MGXv4SOReZtgpng/w==
 =CzWQ
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx

Porting to DM and i.MX8
------------------------

- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
2019-05-01 07:25:51 -04:00
Simon Goldschmidt
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Adam Ford
c7d00f63d1 ARM: omap3_logic: Enable UUID
Instead of hardcoding the mmcroot to /dev/mmcblkX, use the UUID
method.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-25 17:03:25 +02:00
Adam Ford
290097fe27 ARM: omap3_logic: Add NOR Flash Support for SOM-LV
The DM37 and OMAP35 SOM-LV SOM-LV products both support a NOR
flash part connected to CS2 in addition to the NAND part on CS0.
This patch setups the GPMC timings for the MT28 NOR Flash and
enables the CFI-Flash driver now that the CFI stuff is in Kconfig

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-22 09:18:49 -04:00
Adam Ford
46580f2fd5 ARM: LogicPD: omap3logic: Remove Torpedo/SOM-LV autodection
With there now being four device tree files, and 4 separate
defconfig files, the code necessary to determine which board is
being used is no longer necessary as the corresponding pin-muxing
and board names are determined by the device tree.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-10-06 14:09:40 -04:00
Adam Ford
8ccf98b1cf Convert CONFIG_MISC_INIT_R to Kconfig
This converts the following to Kconfig:
   CONFIG_MISC_INIT_R

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17 13:04:00 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Adam Ford
ab5814f992 configs: omap: Remove dead config CONFIG_SYS_NAND_ADDR
CONFIG_SYS_NAND_ADDR is defined and never referenced. This patch
removes the dead code.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-08-10 13:45:33 -04:00
Adam Ford
bdaf24f8a5 ti_omap3_common: Add CONFIG_SYS_NS16550_COMx entries
Several boards do not use the default UART3, so they do a check
for ifdef CONFIG_SPL_BUILD and enable the pointer for
CONFIG_SYS_NS16550_COMx to point to OMAP34XX_UARTx.

Let's consoldate this all into one place, and remove them from the
individual boards.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-08-03 19:53:54 -04:00
Adam Ford
9c5b00973b Convert CONFIG_MTD_PARTITIONS et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MTD_PARTITIONS
   CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-22 19:20:17 -04:00
Adam Ford
e745782c25 omap3_logic: Change console from ttyO0 to ttyS0
Newer kernels have moved from ttyO0 to ttyS0, and when booting
it drops a notice:

  WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
  This ensures that you still see kernel messages. Please
  update your kernel commandline.

This patch updates the console to use ttyS0 and eliminate the
chatter.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-10 16:55:59 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Adam Ford
62896dcbf3 omap3_logic: Fix FDT ADDR for ramdisk booting
The boot scripts for booting from ramdisk are using
${fdtimage} when they really should be using ${fdtaddr}

This patch will fix it so the RAMdisk bootscripts operate
correctly.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-04-06 17:04:33 -04:00
Tom Rini
6f6b7cfa89 Convert all of CONFIG_CONS_INDEX to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-16 10:28:52 -04:00
Adam Ford
61ec4e0742 omap3_logic: Remove unnecessary undefs
Due to evolution of the MMC driver and better support, let's
remove unnecessary undefs.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-03-05 10:16:29 -05:00
Tom Rini
75670c81e4 configs: Migrate CONFIG_SPL_FRAMEWORK
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig.  We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important.  In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-14 12:14:13 -05:00
Adam Ford
3b9e2a2520 Convert CONFIG_TWL4030_USB to Kconfig
This converts the following to Kconfig:
   CONFIG_TWL4030_USB

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-01-22 16:43:30 -05:00
Adam Ford
e13a9dc370 Convert CONFIG_USB_MUSB_HCD et al to Kconfig
This converts the following to Kconfig:
   CONFIG_USB_MUSB_HCD
   CONFIG_USB_MUSB_UDC
   CONFIG_USB_DAVINCI
   CONFIG_USB_OMAP3
   CONFIG_USB_DA8XX
   CONFIG_USB_AM35X

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-01-22 16:43:29 -05:00
Adam Ford
86362221fc Convert CONFIG_USB_MUSB_OMAP2PLUS et al to Kconfig
This converts the following to Kconfig:
   CONFIG_USB_MUSB_OMAP2PLUS
   CONFIG_USB_MUSB_AM35X
   CONFIG_USB_MUSB_DSPS
   CONFIG_USB_MUSB_PIO_ONLY

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-01-22 16:43:29 -05:00
Adam Ford
157af4f81f ARM: omap3_logic: Unlock NAND automatically in U-Boot
The Micron Flash is locked by default.  This will automaticlly
unlock so manually unlocking is unnecessary in U-Boot.

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-12-12 21:33:38 -05:00
Tom Rini
43ede0bca7 Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.

Tested-by: Adam Ford <aford173@gmail.com>  #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-05 11:21:35 -05:00
Adam Ford
8daec2d9d3 net: Add SMC911X driver to Kconfig, convert
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
   CONFIG_SMC911X
   CONFIG_SMC911X_BASE
   CONFIG_SMC911X_16_BIT
   CONFIG_SMC911X_32_BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20 21:40:26 -04:00
Adam Ford
0a9ef45158 Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to Kconfig
This converts the following to Kconfig:
   CONFIG_NAND_MXC
   CONFIG_NAND_OMAP_GPMC
   CONFIG_NAND_OMAP_GPMC_PREFETCH
   CONFIG_NAND_OMAP_ELM
   CONFIG_SPL_NAND_AM33XX_BCH
   CONFIG_SPL_NAND_SIMPLE
   CONFIG_SYS_NAND_BUSWIDTH_16BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
        add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20 16:44:07 -04:00
Maxime Ripard
3f33d3c8f4 usb: gadget: Convert USB_ETHER to Kconfig
The USB Ethernet gadget option has not yet been moved to Kconfig, let's
deal with that.

Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Adam Ford
7672d9d582 include/configs: remove references to SMNAND_ENV_OFFSET
In mancy cases both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR point
to an otherwise-unused SMNAND_ENV_OFFSET.
This patch will set both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR to
whatever value was defined by SMNAND_ENV_OFFSET.

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-13 09:24:26 -04:00
Chris Packham
8ffb23cbf5 Kconfig: drop CONFIG_USB_ETHER_RNDIS
This is not a valid option. Drop it.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-08 10:17:17 -04:00
Adam Ford
db35573a71 omap3_logic: Move CONFIG_SYS_NAND_U_BOOT_OFFS to Kconfig
Manually enable SYS_NAND_U_BOOT_LOCATIONS.
Set CONFIG_SYS_NAND_U_BOOT_OFFS=0x80000 and remove it from header

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-02 10:45:24 -04:00
Adam Ford
6ef2f90108 Convert CONFIG_BCH to Kconfig
This converts the following to Kconfig:
   CONFIG_BCH

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-01 20:45:26 -04:00
Adam Ford
edd1653f04 Convert CONFIG_SPL_OMAP3_ID_NAND to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_OMAP3_ID_NAND

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-01 20:45:26 -04:00
Tom Rini
48f6232e58 Kconfig: Migrate all of cmd/fastboot/Kconfig to defconfigs
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
  not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the README

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-01 16:18:21 -04:00
Simon Glass
e7881d85a9 dm: mmc: Drop CONFIG_DM_MMC_OPS
All boards which use DM_MMC have now been converted to use DM_MMC_OPS.
Drop the option and good riddance.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:59:55 +09:00
Simon Glass
3a91a25376 Convert CONFIG_CMD_SPL_WRITE_SIZE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_SPL_WRITE_SIZE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:58 -04:00
Simon Glass
203dc1b3a8 Convert CONFIG_CMD_SPL_NAND_OFS to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_SPL_NAND_OFS

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:58 -04:00
Adam Ford
daa0f0500f Convert CONFIG_SYS_I2C_OMAP24XX to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_OMAP24XX

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-08-10 12:02:32 +02:00
Adam Ford
94d50bed65 Configs: Migrate CONFIG_SYS_I2C_OMAP34XX to CONFIG_SYS_I2C_OMAP24XX
The driver is for all boards 24XX and up, so let's eliminate the
extra option called CONFIG_SYS_I2C_OMAP34XX since the driver checks
for CONFIG_OMAP34XX we don't need CONFIG_SYS_I2C_OMAP34XX.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2017-08-09 06:14:13 +02:00
Tom Rini
8f1a80e99e configs: Migrate CMD_NAND*
Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.

Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-31 12:21:40 -04:00
Adam Ford
3158eebd21 Remove unused CONFIG_TWL4030_PWM
CONFIG_TWL4030_PWM is not being used by any source, so let's remove the #define
and the whitelist entry

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-07-31 11:22:55 -04:00
Simon Glass
2be296538e Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25 21:08:01 -04:00
Tom Rini
d56b4b1974 configs: Migrate RBTREE, LZO, CMD_MTDPARTS, CMD_UBI and CMD_UBIFS
The above CONFIG options are in Kconfig, and now have correct depends and
inter-dependencies.  Migrate these to configs/ from include/configs/.  In the
case of CMD_UBIFS also change it to be a default y if CMD_UBI.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-24 20:35:55 -04:00
Tom Rini
4125bbcef6 Merge branch 'master' of git://git.denx.de/u-boot-mmc
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to
  match other TI platforms in the same situation.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-16 08:10:50 -04:00
Tom Rini
68ccab5193 omap3: Migrate CONFIG_OMAP3_GPIO_X to Kconfig
The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a
given GPIO bank in U-Boot.  select the required banks for each target.
In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated,
in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO
bank to be enabled if USB is also enabled.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-15 10:40:00 -04:00
Adam Ford
15fde737fc omap3_logic: Add Device Tree Support and more DM drivers
This patch also removes all the excessive code for NS16550 intiailization
as the device tree can do that now.  This also adds DM_I2C and DM_MMC
since the overlying drivers have the built-in support already.  The
corresponding include/config/omap3_logic.h also reduced in size
due to the new device tree support.

Signed-off-by: Adam Ford <aford173@gmail.com>

Changes in V2:
  Retain Auto-detect ability between SOM-LV and Torpedo
  Split this off from the device sub submissions
2017-05-09 20:35:38 -04:00