Commit Graph

115 Commits

Author SHA1 Message Date
Roger Quadros
305a5d840e phy: ti-pipe3: Fix SATA & USB PHY power up sequence
As per "Table 26-7. SATA PHY Subsystem Low-Level Programming Sequence"
in TRM [1] we need to turn on SATA_PHY_TX before SATA_PHY_RX.

[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf

Signed-off-by: Roger Quadros <rogerq@ti.com>
2019-12-26 09:06:54 -05:00
Roger Quadros
277d5d1f9b phy: ti-pipe3: improve DPLL stability for SATA & USB
For increased DPLL stability use the settings recommended in
the TRM [1] for PHY_RX registers for SATA and USB.

For SATA we need to use spread spectrum settings even
though we don't have spread spectrum enabled. The
suggested non-spread spectrum settings don't work.

[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf

Signed-off-by: Roger Quadros <rogerq@ti.com>
2019-12-26 09:06:54 -05:00
Roger Quadros
53df65a9d2 phy: ti-pipe3: Introduce mode property in driver data
Introduce a mode property in the driver data so that
we don't have to keep using "of_device_is_compatible()"
throughtout the driver.

No functional change.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2019-12-26 09:06:54 -05:00
Roger Quadros
b055e67f96 phy: ti-pipe3: Use TRM recommended settings for SATA DPLL
The AM572x Technical Reference Manual, SPRUHZ6H,
Revised November 2016 [1], shows recommended settings for the
SATA DPLL in Table 26-8. DPLL CLKDCOLDO Recommended Settings.

Use those settings in the driver. The TRM does not show
a value for 20MHz SYS_CLK so we use something close to the
26MHz setting.

[1] - http://www.ti.com/lit/ug/spruhz6h/spruhz6h.pdf

Signed-off-by: Roger Quadros <rogerq@ti.com>
2019-12-26 09:06:54 -05:00
Jean-Jacques Hiblot
4e18429883 drivers: phy: Handle gracefully NULL pointers
For some controllers PHYs can be optional. Handling NULL pointers without
crashing nor failing, makes it easy to handle optional PHYs.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-31 07:22:53 -04:00
Tom Rini
ffc379b42c - bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
 - mtmips: add new drivers for clock, reset-controller and pinctrl
 - mtmips: add support for high speed UART
 - mtmips: update/enhance drivers for SPI and ethernet
 - mtmips: add support for MMC
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAl2zFisACgkQKPlOlyTy
 XBgf9RAAkNwLjqUcBz3Ob1briRG5HF4D6bZCpjtkTIO8a2fanUHbSehh30TX8x2X
 z0t/9Sd4OZwAeTxfQ/AlbbVdiB9IMgEb6lJ30Vr88MRNoPhABIQ8hw5xAzFi/6x9
 88YolS/HQo6iR9rzSlaKjdIHhPTH5oQzRJ3JLqSwZzfUNy+zqINEhs3SYCnD2lyV
 gTgiIT3Y5nKrhVHPUCy+jQG+wwWej2NFgwn71vR3/PSQJwxBuasg0qqOKD9hRtpC
 XL6VErE7bf00elO8xjEObYrmB2FpffXJdkazS2HtRYNyKx0quaRNXJt7wqxEVP9L
 M6SmL+S7zBFAetc/iyrlaakPvn7ImehSZkgLYaTPc3yzO+6bgq9tLfBERn/B/s5g
 YyIzPGF66L96nuu0eVGCgSoUBjzBE8l2QTI8dho5xJxjWAUJOWSB0egqfFZzYVFu
 4X37w6Z0j6uTK2oEl7KgJdc0JsZRsAJ8ZiqgOeNeMUTl2RnjGt0Oa7E24Va3n3hM
 5vuEba9nPUFmdC5vlSd2RUK/dB587uKV93r5j54U62clpbiK+VMaRuRVX64ytZvB
 B/0fKyCu+y7bxeZe4/X27jBUOk5yCuxbNI66m+cnnvfHqEmhz5PfDCEK1Dr29oqf
 sCJLgTr7ahyuW4kEoL7KCOBEugPI85fp8/OlqC63M6/Kft0w5sA=
 =6G/J
 -----END PGP SIGNATURE-----

Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips

- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
2019-10-25 20:07:24 -04:00
Weijie Gao
4cce51141f phy: mt76x8-usb-phy: add slew rate calibration and remove non-mt7628 part
This patch adds slew rate calibration for mt76x8-usb-phy, removes code
which belongs to mt7620, and gets rid of using syscon and regmap by using
clock driver and reset controller.

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2019-10-25 17:20:44 +02:00
Jean-Jacques Hiblot
2bbc1bbf5d phy: keystone-usb: handle the transition of the USB power domain
There is no proper power domain support for the keystone platforms.
However we need to turn off the USB domains before jumping to linux or it
fail to boot (observed with k2e and k2l platforms).
This can be done in the PHY driver as it is dedicated only to the keystone
platforms and matches the required on/off sequence.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-10-24 11:28:17 +02:00
Ryder Lee
235bad02e5 phy: mediatek: add MediaTek T-PHY support for PCIe
The driver provides PHY for USB2, USB3.0, PCIe and SATA, and now
we just enable PCIe. As for the other functionalities will be
added gradually in upcoming days.

This is adapted from the Linux version.

Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
2019-10-11 10:10:18 -04:00
Adam Ford
a074667d52 Kconfig: Varios: Fix more SPL, TPL dependencies
Several options are presenting themselves on a various boards
where the options are clearly not used.  (ie, SPL/TPL options
when SPL or TPL are not defined)

This patch is not attempting to be a complete list of items, but
more like low hanging fruit.  In some instances, I wasn't sure
of DM was required, so I simply made them SPL or TPL.

This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-26 11:46:29 -04:00
Sekhar Nori
888e1caeae phy: add support for AM654x SERDES
Add a new SERDES driver for TI's AM654x SoC which configures
the SERDES only for PCIe. Support fo USB3 can be added later.

SERDES in am654x has three input clocks (left input, external
reference clock and right input) and two output clocks (left
output and right output) in addition to a PLL mux clock which
the SERDES uses for Clock Multiplier Unit (CMU refclock).

The PLL mux clock can select from one of the three input
clocks. The right output can select between left input and
external reference clock while the left output can select
between the right input and external reference clock.

The driver has support to select PLL mux and left/right output
mux as specified in device tree.

Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2019-08-12 13:33:39 -04:00
Adam Ford
fc58263d2e phy: Add support for phy-da8xx-usb
In preparation for supporting the musb driver, this patch
adds support for the usb phy associated with the musb driver.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-08 11:35:02 +02:00
Andre Przywara
35fa673e0e sunxi: phy: Add USB PHY support for Allwinner H6
The USB PHY used in the Allwinner H6 SoC has some pecularities (as usual),
which require a small addition to the USB PHY driver:
In this case the second PHY is PHY3, not PHY1, so we need to skip number
1 and 2 in the code. Just use the respective code from Linux for that.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-16 17:13:15 +05:30
Neil Armstrong
277d9167cb phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY drivers
This adds support for the USB PHYs found in the Amlogic G12A SoC Family.

The USB2 PHY supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.

The second driver supports USB3 Host mode or PCIE 2.0 mode, depending on
the layout of the board.
Selection is done by the #phy-cells, making the mode static and exclusive.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-05-09 10:38:32 +02:00
Patrick Delaunay
901f6950a4 phy: usbphyc: increase PLL wait timeout
wait 200us to solve USB init issue on device mode
(ums and stm32prog commands)

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-21 10:26:51 +02:00
Patrick Delaunay
e1904abc1b phy: usbphyc: move vdda1v1 and vdda1v8 in phy_init
vdda1v1 and vdda1v8 are used by the PLL.
Both need to be enabled before starting the PLL.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-21 10:26:51 +02:00
Patrick Delaunay
c50151d43f phy: usbphyc: Binding update of vdda supply
Move supply vdda1v1 and vdda1v8 in usbphyc node and
no more in port

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-21 10:26:51 +02:00
Patrick Delaunay
1655f2da84 phy: usbphyc: update xlate with DT binding
Parameter added for port 1, for example:

&usbh_ehci {
	phys = <&usbphyc_port0>;
	phy-names = "usb";
	vbus-supply = <&vbus_sw>;
	status = "okay";
};

&usbotg_hs {
	pinctrl-names = "default";
	pinctrl-0 = <&usbotg_hs_pins_a>;
	phys = <&usbphyc_port1 0>;
	phy-names = "usb2-phy";
	status = "okay";
};

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-21 10:26:51 +02:00
Patrick Delaunay
6841d83cec phy: usbphyc: remove unused variable index
Remove unused field index in struct stm32_usbphyc_phy.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-21 10:26:51 +02:00
Stefan Roese
d7d7606c7e phy: Add USB PHY driver for the MT76x8 (7628/7688) SoC
This driver is derived from this Linux driver:
linux/drivers/phy/ralink/phy-ralink-usb.c

The driver sets up power and host mode, but also needs to configure PHY
registers for the MT7628 and MT7688.

I removed the reset controller handling for the USB host and device, as
it does not seem to be necessary right now. The soft reset bits for both
devices are enabled by default and testing has shown (with hackish
reset handling added), that USB related commands work identical with
or without the reset handling.

Please note that the resulting USB support is tested only very minimal.
I was able to detect one of my 3 currently available USB sticks.
Perhaps some further work is needed to fully support the EHCI controller
integrated in the MT76x8 SoC.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-04-12 17:32:53 +02:00
Neil Armstrong
82548aaad5 phy: Also allow MESON_GXM for MESON_GXL_USB_PHY
The MESON_GXL_USB_PHY is also used on the Amlogic Meson GXM SoCs.

Fixes: 2960e27e38 ("phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-04-03 10:23:38 -04:00
Jagan Teki
089ffd0aed phy: sun4i-usb: Use CLK and RESET support
Now clock and reset drivers are available for respective
SoC's so use clk and reset ops on phy driver.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2019-01-18 22:19:09 +05:30
Jean-Jacques Hiblot
512a84c444 phy: omap_usb2: Add support for am437x
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-14 17:59:09 +01:00
Jean-Jacques Hiblot
4b12783c8e PHY: Add phy driver for the keystone USB PHY
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-12-14 17:59:09 +01:00
Jean-Jacques Hiblot
668257e023 phy: Add a new driver for OMAP's USB2 PHYs
This drivers supports the USB2 PHY found on omap5 and dra7 SOCs.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-07 16:31:46 +01:00
Vignesh R
0752d7013a phy: ti-pip3-phy: Add support for USB3 PHY
Add support to handle USB3 PHYs present on AM57xx/DRA7xx SoCs. This is
needed to move AM57xx to DM_USB.

Signed-off-by: Vignesh R <vigneshr@ti.com>

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-12-07 16:31:46 +01:00
Patrick Delaunay
22929e1266 drivers: cosmetic: Convert SPDX license tags to Linux Kernel style
Complete in the drivers directory the work started with
commit 83d290c56f ("SPDX: Convert all of our single
license tags to Linux Kernel style").

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-10-28 09:26:39 -04:00
Marek Vasut
6cfc3d664e phy: rcar: Add R-Car Gen3 PHY driver
Add a PHY driver for the R-Car Gen3 which allows configuring
USB OTG PHY on Gen3 into host mode and toggles VBUS in case a
dedicated regulator is present.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-10-03 12:56:13 +02:00
Ramon Fried
92454e47bc phy: db410c: Add MSM USB PHY driver
Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.

Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
2018-09-30 13:00:36 -04:00
Rabeeh Khoury
d13b740ca6 phy: marvell: add SATA comphy RX/TX polarity invert support
This patch adds support to Armada 7k/8k comphy RX/TX lane swap. The
'phy-invert' DT property defines the inverted signals.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 13:54:27 +02:00
Marek Behún
4b8cb84327 phy: marvell: Support changing SERDES map in board file
This adds a weak definition of comphy_update_map to comphy_core,
which does nothing. If this function is defined elsewhere, for example
in board file, the board file can change some parameters of SERDES
configuration.

This is needed on Turris Mox, where the SERDES speed on lane 1 has to
be set differently when SFP module is connected and when Topaz Switch
module is connected.

This is a temporary solution. When the comphy driver for armada-3720
will be added to the kernel, the comphy driver in u-boot shall also be
updated and this should be done differently then.

Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 08:59:26 +02:00
Marek Vasut
664258887d phy: rcar: Add R-Car Gen2 PHY driver
Add a PHY driver for the R-Car Gen2 which allows configuring the mux
connected to the EHCI controllers and USBHS controller.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-08-14 11:31:19 +02:00
Marek Vasut
5e50adf667 phy: Fix off-by-one error when parsing DT PHY bindings
The code fails to copy the last PHY phandle argument, so it is
missing from the adjusted phandle args and the consumer cannot
use it to determine what the PHY should do.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
2018-08-14 11:31:19 +02:00
Jagan Teki
69aa1b234e phy: sun4i-usb: Update PHY#3 rst_mask only for H3_H5
Only H3 and H5 have 4 PHYS so restrict rst_mask only for them
by checking PHY id as 3 and update the proper bits.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:41:49 +05:30
Jagan Teki
52185b094d phy: sun4i-usb: Remove usb_clk_cfg set in probe
usb_clk_cfg is setting CTRL_PHYGATE bit value in probe
which is BIT 0 for sun4i, 6i and 8 for a83t but all
these were handling in phy ops init exit calls.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:41:45 +05:30
Jagan Teki
0bfcb47aa0 phy: sun4i-usb: Call phy_passby even for PHY#0
On newer Allwinner SoC, there is a pair of EHCI/OHCI USB hosts
for OTG host mode. USB PHY passby must be configured for its
corresponding PHY. so we can call for PHY#0. on the other hand
in past usb-phy code the same thing can be restricted for
Lower SoC's, other than H3/H5/A64.

Now there is no need to restrict usb passby since the phy driver
is DT enabled, and the respective phy calls will trigger based
DT information initiated by the drivers.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:41:41 +05:30
Patrice Chotard
a1b2faed7c phy: Be able to get phy from PHY provider
In case of phy are provided from a PHY provider nodes as following:

usbphyc: usb-phy@5a006000 {
	compatible = "st,stm32mp1-usbphyc";
	reg = <0x5a006000 0x1000>;
	clocks = <&rcc_clk USBPHY_K>;
	resets = <&rcc_rst USBPHY_R>;
	#address-cells = <1>;
	#size-cells = <0>;

	usbphyc_port0: usb-phy@0 {
		reg = <0>;
		phy-supply = <&vdd_usb>;
		vdda1v1-supply = <&reg11>;
		vdda1v8-supply = <&reg18>
		#phy-cells = <0>;
	};

	usbphyc_port1: usb-phy@1 {
		reg = <1>;
		phy-supply = <&vdd_usb>;
		vdda1v1-supply = <&reg11>;
		vdda1v8-supply = <&reg18>
		#phy-cells = <1>;
	};
};

and PHY are called as following:

usbh_ehci: usbh-ehci@5800d000 {
	compatible = "generic-ehci";
	reg = <0x5800d000 0x1000>;
	clocks = <&rcc_clk USBH>;
	resets = <&rcc_rst USBH_R>;
	interrupts = <GIC_SPI 75 IRQ_TYPE_NONE>;
	companion = <&usbh_ohci>;
	phys = <&usbphyc_port0>;
	phy-names = "usb";
	status = "okay";
};

generic_phy_get_by_index() must be updated to first look for
PHY phandle as previously and in case of error looks for PHY
provider by finding the parent's current node which is the PHY
provider.
args (ofnode_phandle_args struct) must also be updated by inserting
the phy index into the PHY provider as args[0].

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-07-19 16:31:35 -04:00
Tom Rini
809e0e398a Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2018-06-04 08:55:00 -04:00
Álvaro Fernández Rojas
9ca33ebf1c phy: bcm6318-usbh: convert to use live dt
Also fix bad accents in my name.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Álvaro Fernández Rojas
25d8380f22 phy: bcm6368-usbh: convert to use live dt
Also fix bad accents in my name.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Álvaro Fernández Rojas
5a1ab87f53 phy: bcm6358-usbh: convert to use live dt
Also fix bad accents in my name.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Álvaro Fernández Rojas
50d16bcf33 phy: bcm6348-usbh: convert to use live dt
Also fix bad accents in my name.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2018-06-01 15:56:02 +02:00
Jagan Teki
aa29b11b3f phy: sun4i-usb: Add a sunxi specific function for setting squelch-detect
The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.

The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
194ccb9a34 phy: sun4i-usb: Add A23 USB PHY config
Allwinner A23 has 2 USB PHY's and 0x04 has phy ctrl offset.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
61bf0ed5db phy: sun4i-usb: Add A33 USB PHY config
Allwinner A33 has 2 USB PHY's and 0x10 has phy ctrl offset.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
bf986d1f60 phy: sun4i-usb: Add A31 PHY config
Allwinner A31 has 3 USB PHY's and rest similar to A10.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
7f90b557c9 phy: sun4i-usb: Add A10/A13/A20 PHY config
Add PHY configs for Allwinner A10/A13/A20 which are SUN4I.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
5f646bf1d7 phy: sun4i-usb: Add A83T USB PHY config
Unlike, other Allwinner SUN4I Phy supporting SOC, A83T has
2 USB PHY's and second one is HSIC. So phy control need to
configure to handle these HSIC and SIDDQ requirement.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
bafe5e3061 phy: sun4i-usb: Add V3S PHY config
V3S has 1 USB PHY, rest are similar to A64.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30
Jagan Teki
43519c4da7 phy: sun4i-usb: Add H3/H5 PHY config
H3/H5 has 4 USB PHY, rest are similar to A64.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
2018-05-28 16:40:43 +05:30