We can simplify some cpu/SoC level initialization by moving it to be
after the environment and non-volatile storage is setup as there might
be dependancies on such things in various boot configurations.
For example for FSL SoC's with QE if we boot from NAND we need it setup
to extra the ucode image to initialize the QE. If we always do this
after environment & non-volatile storage is working we can have the code
be the same regardless of NOR, NAND, SPI, MMC boot.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move some processor specific QE defines into config_mpc85xx.h and use
QE_MURAM_SIZE to cleanup some ifdef mess in the QE immap struct.
Also fixed up some comment style issues in immap_qe.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards
pretty much do the same thing. The only variations are in how many
controllers or DIMMs per controller exist. To make this work we
standardize on the names of the SPD_EEPROM_ADDRESS defines based on the
use case of the board.
We allow boards to override get_spd to either do board specific fixups
to the SPD data or deal with any unique behavior of how the SPD eeproms
are wired up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Every 85xx board implements fsl_ddr_get_mem_data_rate via get_ddr_freq()
and every 86xx board uses get_bus_freq(). If implement get_ddr_freq()
as a static inline to call get_bus_freq() we can remove
fsl_ddr_get_mem_data_rate altogether and just call get_ddr_freq()
directly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We've been utilizing board_lmb_reserve to reserve the boot page for MP
systems. We can just move this into arch_lmb_reserve for 85xx & 86xx
systems rather than duplicating in each board port.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In a manner similar to passing ethernet stashing parameters into device
tree for "gianfar", extend the support to the "fsl,etsec2" as well.
Signed-off-by: Pankaj Chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove declerations of fsl_ddr_set_memctl_regs in board files with and
place it into a common header.
Based on patch from Poonam Aggrwal.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Integrated Flash Controller (IFC) is used to access the external
NAND Flash, NOR Flash, EPROM, SRAM and Generic ASIC memories.Four chip
selects are provided in IFC so that maximum of four Flash devices can be
hooked, but only one can be accessed at a given time.
Features supported by IFC are,
- Functional muxing of pins between NAND, NOR and GPCM
- Support memory banks of size 64KByte to 4 GBytes
- Write protection capability (only for NAND and NOR)
- Provision of Software Reset
- Flexible Timing programmability for every chip select
- NAND Machine
- x8/ x16 NAND Flash Interface
- SLC and MLC NAND Flash devices support with
configurable
page sizes of upto 4KB
- Internal SRAM of 9KB which is directly mapped and
availble at
boot time for NAND Boot
- Configurable block size
- Boot chip select (CS0) available at system reset
- NOR Machine
- Data bus width of 8/16/32
- Compatible with asynchronous NOR Flash
- Directly memory mapped
- Supports address data multiplexed (ADM) NOR device
- Boot chip select (CS0) available at system reset
- GPCM Machine (NORMAL GPCM Mode)
- Support for x8/16/32 bit device
- Compatible with general purpose addressable device
e.g. SRAM, ROM
- External clock is supported with programmable division
ratio
- GPCM Machine (Generic ASIC Mode)
- Support for x8/16/32 bit device
- Address and Data are shared on I/O bus
- Following Address and Data sequences can be supported
on I/O bus
- 32 bit I/O: AD
- 16 bit I/O: AADD
- 8 bit I/O : AAAADDDD
- Configurable Even/Odd Parity on Address/Data bus
supported
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are only
ever connected on SERDES.
Updated MPC85xx_PORDEVSR_IO_SEL & MPC85xx_PORDEVSR_IO_SEL_SHIFT
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1011, P1012, P1015, P1016, P1020, P1021, P1024, & P1025 SoCs require
that we initialize the SERDES registers if the lanes are configured for
PCIe. Additionally these devices PCIe controller do not support ASPM
and we have to explicitly disable it.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable workaround for errata ELBC A001, ESDHC 111 & SATA A001 on
P1022/P1013 SoCs.
Also updated P1022DS config to properly enable CONFIG_FSL_SATA_V2.
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, _end is used for end of BSS section. We want _end to mean
end of u-boot image, so we rename _end to __bss_end__ first.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
The fix for errata workaround is to avoid covering physical address
0xff000000 to 0xffffffff during the implementation.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
rcw_en bit is only available for DDR3 controllers. It is a reserved bit on
DDR1 and DDR2 controllers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To recognize DIMMs with ECC capability by testing ECC bit only. Not to be
confused by Address Parity bit.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit 8aba9dceeb
Divides variable of linker flags to LDFLAGS-u-boot and LDFLAGS
breaks the usage of --gc-section to build nand_spl. We still need linker option
--gc-section for every uboot image, not only the main one. LDFLAGS_FINAL passes
the --gc-sections to each uboot image.
To get the proper linker flags, we use LDFLAGS and LDFLAGS_FINAL to replace
PLATFORM_LDFLAGS in the Makefile of each nand_spl board.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
There is a small ordering issue in the master core in that we need to
make sure the disabling of the timebase in the SoC is visible before we
set the value to 0. We can simply just read back the value to
synchronizatize the write, before we set TB to 0.
Reported-by: Dan Hettena
Tested-by: Dan Hettena
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The POST word is stored in a spare register in the PIC on MPC8[5/6]xx
processors. When interrupt_init() is called, this register gets reset
which resulted in all POST_RAM POSTs not being ran due to the corrupted
POST word. To resolve this, store off POST word before the PIC is
reset, and restore it after the PIC has been initialized.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Copying directly from ECM/PQ3 is not correct for how CoreNet based
platforms handle boot page translation.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The write recovery time of both registers should match. Since mode register
doesn't support cycles of 9,11,13,15, we should use next higher number for
both registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When DDR data rate is higher than 1200MT/s or controller interleaving is
enabled, additional cycle for write-to-read turnaround is needed to satisfy
dynamic ODT timing.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Use SPMR instead of HRCWL when calculating clocks as HCRWL
may be changed and the CPU will not pick up all changes
until there is a POR. u-boot will think SPMF has changed and get
the clocks wrong.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fix a problem for the pcie enumeration when the mpc83xx
pcie controller is connected with switch or we use both of the two
pcie controller.
Signed-off-by: Leo Liu <liucai.lfn@gmail.com>
fix codingstyle and compiler warning: 'pcie_priv' defined but not used
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The P1013 is a single core version of P1022 and thus should use the
p1022_serdes.c code. It was acciently pointing to p1013_serdes.c which
doesn't exist.
Reported-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Workaround for the following errata:
DDR111 - MCKE signal may not function correctly at assertion of HRESET
DDR134 - The automatic CAS-to-Preamble feature of the DDR controller can
calibrate to incorrect values
These two workarounds must be implemented together because they touch
common registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use unique erratum number instead of platform number.
Enable command that reports errata on MPC8572DS.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This polling loop is not required normally, unless specifically stated in
workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linker needs to use the proper endian/bfd flags even when doing partial linking.
LDFLAGS_u-boot sets linker option which is called it when U-boot is built
(u-boot final).
LDFLAGS sets necessary option by partial linking (use in cmd_link_o_target).
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
ctrl_regs.c: In function 'set_ddr_sdram_mode_2':
ctrl_regs.c:690:6: warning: unused variable 'i'
'i' is only used by DDR3 code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Future SoC (like the P1010) replace the LBC controller with the new IFC
(Integrated Flash Controller) so ensure we properly protect code that is
related to the LBC.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Hwconfig is called before relocating. Use the new hwconfig APIs.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Extend board specific parameters to include cpo, write leveling override
Extend write leveling sample to 0xf
Adding rcw overrid for quad-rank RDIMMs
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum DDR-A003 requires workaround to correctly set RCW10 for registered DIMM.
Also adding polling after enabling DDR controller to ensure completion.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added fsl_ddr_get_version() function to for DDR3 to poll DDRC IP version
(major, minor, errata) to determine if unique mode registers are available.
If true, always use unique mode registers. Dynamic ODT is enabled if needed.
The table is documented in doc/README.fsl-ddr. This function may also need
to be extend for future other platforms if such a feature exists.
Enable address parity and RCW by default for RDIMMs.
Change default output driver impedance from 34 ohm to 40ohm. Make it 34ohm for
quad-rank RDIMMs.
Use a formula to calculate rodt_on for timing_cfg_5.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch exposes more registers which can be used by the DDR drivers or
interactive debugging. U-boot doesn't use all the registers in DDRC.
When advanced tuning is required, writing to those registers is needed.
Add writing to cdr1, cdr2, err_disable, err_int_en and debug registers
Add options to override rcw, address parity to RDIMMs.
Use array for debug registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add fsl_ddr:ecc=on in hwconfig. If ECC is enabled in board configuration file,
ECC can be turned on/off by this switch. If this switch is omitted, it is ON by
default.
Updated hwconfig calls to use local buffer.
Syntax is
hwconfig=fsl_ddr:ecc=on
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.
Eventually this should be handled by Kconfig & defconfigs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
There are several users of the hwconfig APIs (8xxx DDR) before we have
the environment properly setup. This causes issues because of the
numerous ways the environment might be accessed because of the
non-volatile memory it might be stored in. Additionally the access
might be so early that memory isn't even properly setup for us.
Towards resolving these issues we provide versions of all the hwconfig
APIs that can be passed in a buffer to parse and leave it to the caller
to determine how to allocate and populate the buffer.
We use the _f naming convention for these new APIs even though they are
perfectly useable after relocation and the environment being ready.
We also now warn if the non-f APIs are called before the environment is
ready to allow users to address the issues.
Finally, we convert the 8xxx DDR code to utilize the new APIs to
hopefully address the issue once and for all. We have the 8xxx DDR code
create a buffer on the stack and populate it via getenv_f().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Add P2040 SoC specific information:
* SERDES Table
* Added p2040 to cpu_type_list and SVR list
* Added number of LAWs for p2040
* Set CONFIG_MAX_CPUS to 4 for p2040
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
