The new rk3288 revision rk3288w has some changes with respect
to legacy rk3288 like hclk_vio in cru and usb host0 ohci.
Linux clock driver already handle this via rockchip,rk3288w-cru
compatible.
USB ohci host can enable via dts for rk3288w based boards.
So, add fdt board setup code to update cru compatible with
rk3288w-cru compatible if the SOC revision is RK3288W.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip SoC's has a new revision chip for rk3288 SoCs.
RK3288 has a new revision chip called RK3288W which is similar
but different hclk_vio clock and fixed OHCI host.
Add common Rockchip SoC detection helper to support this rk3288w
detection.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.
So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.
- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
GPIO pin change compared to 4B, 4C
So move common nodes, properties into dtsi file and include
on respective variant dts files.
Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To fix below build error:
drivers/usb/host/built-in.o: In function `xhci_dwc3_remove':
drivers/usb/host/xhci-dwc3.c:174: undefined reference to `dwc3_shutdown_phy'
drivers/usb/host/built-in.o: In function `xhci_dwc3_probe':
drivers/usb/host/xhci-dwc3.c:130: undefined reference to `dwc3_setup_phy'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add default kernel_comp_addr_r and kernel_comp_size to support boot
from compressed kernel Image, this space is temporarily used during
decompress according to README.distro.
Reported-by: Tian Yuanhao <tianyuanhao@aliyun.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Currently 2.5 GB is calculated as DRAM size for a 1 GB RK322x board
if CONFIG_SPL_OPTEE is set. This is troublesome when booting a
linux kernel since this size will be injected in FDT of the kernel.
gd->bd->bi_dram[0].start (which is basically CONFIG_SYS_SDRAM_BASE)
must not be taken into consideration for calculation of second bank
size, since this offset is already included in calculation of "top".
After applying this patch 992 MB (1024 MB - 32 MB reserved for
optee-os) is correctly calculated and has also been verified on
2 GB boards.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Drop the legacy PHY driver and it's associated code since
the PHY handling driver now part of Generic PHY framework.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Now, we have a PCIe PHY driver as part of the Generic
PHY framework. Let's use it instead of legacy PHY driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the Rockchip PCIe PHY driver as part of
Generic PHY framework.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Disable ram rockchip debug driver for roc-rk3399-pc
boards since we have verified ram in many instances
with respective U-Boot versions.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The empty function define should not be in the header file, or else the
build will error with function multi definition after CONFIG_RAM_ROCKCHIP_DEBUG
is disabled.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Right now all these debug statements are printing on the
console to make sure proper dram initialization happens.
Mark them into RAM_ROCKCHIP_DEBUG would be more meaningful
and work like before since the RAM_ROCKCHIP_DEBUG is by
default yet.
No functionality changes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
stride debug is already present in sdram_common.c via
RAM_ROCKCHIP_DEBUG.
So, drop the redundant debug stride code in rk3399 driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI Flash support for the PINE64 Rock64 board
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add U-Boot SPI support for the RK3328
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(fix checkpatch error for code ident)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the RK3328 SPI controller
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add SPI support for the RK3328 clock driver
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Adjust the ENV offset, size to fit into all images
on 16MB flash.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable DWC3 core, gadget for roc-rk3399-pc board.
This would help to use fastboot by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable config options to get HDMI output on RockPI-4 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB gadget for rock-pi-4 boards.
This would help to use fastboot by default.
Note: Connect the Host USB cable (Port A or C) to rock-pi-4
Upper USB 3.0 port.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable PCI/NVME for M.2 Slot on RockPI-4 boards.
=> nvme info
Device 0: Vendor: 0x144d Rev: 2B2QEXM7 Prod: S4EUNG0MC10012Y
Type: Hard Disk
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB3.0 Host support for RockPI-4 boards.
Note that the Upper USB3.0 port is marked as otg and
lower USB3.0 port marked as host, so this below log
capture when USB3.0 mass storage plug in at lower
USB 3.0 port.
Log:
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 040130e3ee554b7078843f4eb331646
Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB3.0 Host support for RockPro64 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Get the devicetree from mainline Linux and include it for U-Boot uses.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3326 is just a trimmed down px30 from a software perspective,
so the mainline rk3326 dtsi also ist just a tiny addition.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A large number of assorted fixes, including but not limited to:
- Correct fixdep and CONFIG_IS_ENABLED(...)
- lz4 on big endian
- Assorted LMB hardening
- Remove bd_t typedef
Add VendorID and DeviceID for supported devices on OcteonTX/TX2
platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When update_uboot.its is used directly there is syntax error for no reason.
Error report:
mkimage -f update_uboot.its boot
Error: update_uboot.its:18.12-13 syntax error
FATAL ERROR: Unable to parse input tree
mkimage: Can't read boot.tmp: Invalid argument
Fixes: 4bae90904b ("Automatic software update from TFTP server")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The types of "offset" and "size" of "struct mtd_partition" are uint64_t,
while mtd_parse_partitions() uses int to work with these values. When
the offset reaches 2GB, it is interpreted as a negative value, which
leads to error messages like
mtd: partition "<partition name>" is out of reach -- disabled
eg. when using the "ubi part" command.
Fix this by using uint64_t for cur_off and cur_sz.
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
When fixdep detects CONFIG_IS_ENABLED and other similar macros, it must
parse the macro parameter to determine which actual CONFIG_ option is
being referenced. This involves moving a pointer forward through the
entire CONFIG_ option "word". Currently, the code uses variable q to walk
through the word, but doesn't actually initialize it to point at the
parameter before doing so. Consequently, the walking process immediately
fails since it sees the macro invocatoins's ( rather than the expected
alpha-numeric characters in the macro parameter. Fix this by adding the
missing initialization.
Fixes: 67f2ee86cc ("kbuild: fixdep: Resync this with v4.17")
Fixes: 7012865e96 ("gpio: fix test.py for gpio label lookup")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new error message in case the size of data written
are shorter than the one expected.
Currently, it will lead to the following error message:
"mkimage: Write error on uImage: Success"
This is not explicit when the error is because the device
doesn't have enough space. Let's use a more understandable message:
"mkimage: Write only 4202432/4682240 bytes, probably no space left on the device"
Signed-off-by: Mylène Josserand <mylene.josserand@collabora.com>
Reviewed-by: Walter Lozano <walter.lozano@collabora.com>
Since commit 4b0bcfa7c4 (Kconfig: Migrate CONFIG_BOOTM_* options),
the config_defaults.h file has been void of any actual content - and
these days, "sane defaults for everyone" is achieved by appropriate
default values in Kconfig. Remove it, and thus make every translation
unit process one less header file.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Remove the incorrect usage of double underscores for the
CONFIG_OF_LIST and CONFIG_SPL_OF_LIST symbols.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
If a file cannot be loaded, show an error message.
Set the EFI boot device only after successfully loading a file.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some code was not converted by coccinelle, somehow.
I manually fixed up the remaining, and comments, README docs.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[trini: Add arch/arm/mach-davinci/include/mach/sdmmc_defs.h and
include/fdt_support.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
All configurations have been removed in 2016 by commit 7985cdf74b
("arm64: Remove non-full-va map code").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This fixes the CVE-2016-9840. Commit imported from [1].
inftrees.c was subtracting an offset from a pointer to an array,
in order to provide a pointer that allowed indexing starting at
the offset. This is not compliant with the C standard, for which
the behavior of a pointer decremented before its allocated memory
is undefined. Per the recommendation of a security audit of the
zlib code by Trail of Bits and TrustInSoft, in support of the
Mozilla Foundation, this tiny optimization was removed, in order
to avoid the possibility of undefined behavior.
[1]: 6a043145ca
Signed-off-by: Mark Adler <madler@alumni.caltech.edu>
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
- Despite other ext4 filesystem functions, ext4fs_mount returns
0 in case of error.
- This leads to u-boot crash in case that an SD card
with valid partition table but without ext4 filesystem created
in a partition is found on SD card.
- Fix this by returning a proper error code of '-1' from spl_load_image_ext
function in case of ext4fs_mount error.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
[hthiery: slightly reword the commit message]
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Moving of the OS image may have some nasty side effects like corrupting
DTB. Convert the current debug print to printf so that the relocation of
the OS is always obvious to the user.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
These cases are typically fatal and are difficult to debug for random
users. Add checks for detecting overlapping images and abort if overlap
is detected.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
