The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.
The dts file is identical to the one submitted upstream.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These files are based on the current latest upstream kernel work. The
bus_gates bindings may still change, but for u-boot that does not matter
as we do not (yet) use any clock info from devicetree for sunxi u-boot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.
PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.
The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on existing A23/A33 code and the original H3 boot0.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Change to ns16550 uart for 10m50 devboard based on a new
Altera release.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_tegra, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_rockchip, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_ppc, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add TODO comment]
Signed-off-by: Tom Rini <trini@konsulko.com>
Unify serial_x86, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a test that verifies that USB keyboards work correctly on sandbox.
This verifies some additional parts of the USB stack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple USB keyboard driver for sandbox. It provides a function to
'load' it with input data, which it will then stream through to the normal
U-Boot input subsystem. When the input data is exhausted, the keyboard stops
providing data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add tests that this command produces the right output, even when a rescan
results in a device disappearing from the bus.
Signed-off-by: Simon Glass <sjg@chromium.org>
When running sandbox tests, silence the console to avoid unwanted output.
Also, record the console in case tests want to check it.
The -v option can be used to enable stdout during tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some tests are slow due to delays which are unnecessary on sandbox. The
worst offender is USB where we lose two seconds. Add a way to disable time
delays.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards have an i8042 device. Enable the driver for all x86 boards, and
add a device tree node for those which may have this keyboard.
Also adjust the configuration so that i8042 is always separate from the VGA,
and rename the stdin driver accordingly. With this commit the keyboard will
not work, but it is fixed in the next commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a sandbox timer which get time from host os and a basic
test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adjust the cros_ec keyboard driver to support driver model. Make this the
default for all Exynos boards so that those that use a keyboard will build
correctly with this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the tegra keyboard driver to support driver model, using the new
uclass. Make this the default for all Tegra boards so that those that use
a keyboard will build correctly with this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
'extern inline' is not portable across various C standards. To ensure
compatiblity with various standards/compilers change the functions to
static inline. This is a portable construct and serves as a comparable
definition to 'extern inline' from the gnu90 standard.
Additionally remove the function prototypes as they are not required due
to the functions being declared static and functions are correctly
ordered based on dependence.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Put jump trampoline to TCM at 0 and setup R5 reset address to 0.
Jump trampoline ensures that jump to the right location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently the mmc device that SPL looks at is always mmc0, regardless
of the BOOT_DEVICE_MMCx value. This forces some boards to
implement hacks in order to boot from other mmc devices.
Make SPL take into account the correct mmc device.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.
Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).
Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728
The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.
Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.
NOTE: Commit eae7ae1853 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.
As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Zap ioremap(), as it is replaced by map_physmem(,,MAP_NOCACHE).
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Change ioremap() to map_physmem(), as it is more used in u-boot.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Instead of allocating space in the driver for the serdes
specification table, just allow the board file to set a pointer
to it. Also, allow the board to only specify the lanes that are
used instead of including unused lanes.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Functions that do not modify the pointer passed should declare it
as const.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support. Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM. If this needs to be done, it should be
handled in the board file, not in core code.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
With this change Synopsys DesignWare SDP board is switched to driver
model for both serial port (serial_dw) and Ethernet (Designware GMAC).
This simplifies include/configs/axs101.h and allows for reuse of Linux's
Device Tree description.
For simplicity Linux's .dts files are not blindly copied but only very
few extracts of them are really used (those that are supported in U-Boot
at the moment).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
common/usb.c unconditionally includes <asm/processor.h>
And now to allow USB support on ARC boards we have to have that header.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Up until now there was no need in those stubs.
But since following commit compilation of U-Boot on ARC is broken:
------------------------>8----------------------
commit 7861204c9a
Author: Stephen Warren <swarren@wwwdotorg.org>
Date: Sat Oct 3 13:56:46 2015 -0600
itest: make memory access work under sandbox
itest accesses memory, and hence must map/unmap it. Without doing so, it
accesses invalid addresses and crashes.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
------------------------>8----------------------
That's because CMD_ITEST is enabled by default in common/Kconfig and now
map_physmem()/unmap_physmem() is used there.
So this patch adds missing stubs for ARC.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Enable TI_EDMA3 and QUAD read support for ti_qspi on am43xx, this
increases read performance to 4 MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Now that we have converted all x86 boards to use driver model pci,
remove these legacy pci codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move chipset-specific codes such as PAM init, PCIe ECAM and MP table
from pci.c to qemu.c, to prepare for DM PCI conversion.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The call to pci_run_vga_bios() is not needed as this is handled
in the vesa_fb driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
According to Atom E6xx datasheet, setting VGA Disable (bit17)
of Graphics Controller register (offset 0x50) prevents IGD
(D2:F0) from reporting itself as a VGA display controller
class in the PCI configuration space, and should also prevent
it from responding to VGA legacy memory range and I/O addresses.
However test result shows that with just VGA Disable bit set and
a PCIe graphics card connected to one of the PCIe controllers on
the E6xx, accessing the VGA legacy space still causes system hang.
After a number of attempts, it turns out besides VGA Disable bit,
the SDVO (D3:F0) device should be disabled to make it work.
To simplify, use the Function Disable register (offset 0xc4)
to disable both IGD (D2:F0) and SDVO (D3:F0) devices. Now these
two devices will be completely disabled (invisible in the PCI
configuration space) unless a system reset is performed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Rename pcat_timer.c to i8254.c and pcat_interrupts.c to i8259.c,
to match their header file names (i8254.h and i8259.h).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Initialize counter 1, used to refresh request signal. This is
required for legacy purpose as some codes like vgabios utilizes
counter 1 to provide delay functionality.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This cleans up i8254 and i8259 codes to fix several cosmetic
issues, like coding convention and some comments improvement.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
PARANOID_IRQ_TRIGGERS is not referenced anywhere in U-Boot.
Remove these dead codes wrapped by it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_SYS_NUM_IRQS is actually not something we can configure,
but an architecture defined number of ISA IRQs. Move it from
x86-common.h to asm/interrupt.h and rename it to SYS_NUM_IRQS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update the LEON2/3 serial driver to make use of the readl and writel
macros as well as the WATCHDOG_RESET() macro.
Add readl/writel and friends to the asm/io.h file.
Introduce the gd->arch.uart variable to store register address.
Lastly, remove baudrate scaler macro variables from board config. It
is now calculated in the serial driver using the global data variable.
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
Fixes broken search and replaced license changes in
files cpu/leon3/start.S and include/asm/winmacro.h
from commit 1a4596601f
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
Series-to: u-boot
Series-cc: Tom Rini <trini@konsulko.com>
Series-version: 2
Cover-letter:
sparc: Updates to SPARC architecture in preperation for generic board
This patch series is a backlog of preparation work for upcomming
generic board changes.
I first want to get these reviewed and submitted to mainline before
sending out more patches.
END
Dear u-boot community,
I just made a small change on the openrisc-generic platform
configuration to take in account the new naming convention (or1k instead
of or32, so the build process gets fine).
Could you take care to review and approve the following patch, please?
Kind regards,
The gdsys strider board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x 10/100 Mbit/s Ethernet (optional)
- Lattice ECP3 FPGA connected via eLBC
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
[trini: Drop setting CONFIG_SYS_GENERIC_BOARD, this is always true now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix below compilation warnings-
drivers/gpio/hi6220_gpio.c: In function ‘hi6220_gpio_probe’:
drivers/gpio/hi6220_gpio.c:82:15: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
bank->base = (u8 *)plat->base;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Compile misc.c for mx7, since we need related function for
lcdif and nand.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Need to call lcdif_power_down to make lcdif in initial state
before kernel boot. Similar issue for uboot reset with lcdif
enabled, system will hang after serveral times resetting. Need
to let lcdif initial state to make all go well.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
We need to power down lcdif before uboot reset to make reset can pass
stress test.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Introudce a new function lcdif_power_down.
1. Waits for a VSYNC interrupt to guarantee the reset is done at the
VSYNC edge, which somehow makes the LCDIF consume the display FIFO(?)
and helps the LCDIF work normally at the kernel stage.
2. Add power down function to stop lcdif.
The reason to introduce lcdif_power_down is that we want lcdif to be in
initial state when doing uboot reset or before kernel boot to make
system stable, otherwise system may hang.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Implement mxs_set_lcdclk, enable_lcdif_clock and enable_pll_video.
The three API can be used to configure lcdif related clock when
CONFIG_VIDEO_MXS enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
1. Move WDOG3_BASE_ADDR to '#if !(defined(__ASSEMBLY__))'.
2. Add i.MX6UL LCDIF register base address. And Introduce
LCDIF1_BASE_ADDR to support runtime check.
3. include <asm/imx-common/regs-lcdif.h> for imx-regs.h to avoid
building error for mxsfb.c, since mxsfb.c use imx-regs.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Share one lcdif structure for i.MXes.
1. Discard struct mxs_lcdif_regs from imx-regs.h of i.MX7
2. Add i.MX6SX/6UL/7D support in imx-lcdif.h of imx-common
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Move 'struct mxs_lcdif_regs' and lcdif related macro definitions to
arch/arm/include/asm/imx-common/regs-lcdif.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
There are uint8_t, uint32_t types in regs-common.h, so include
linux/types.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Change mxs_set_lcdclk prototype to add a new parameter
base_addr. There are two LCD interfaces for i.MX6SX,
we may support LCDIF1 or LCDIF2.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
1. add basic psci support for imx7 chip.
2. support cpu_on and cpu_off.
3. switch to non-secure mode when boot linux kernel.
4. set csu allow accessing all peripherial register in non-secure mode.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The code such as PSCI in section named secure is bundled with
u-boot image, and when bootm, the code will be copied to their
runtime address same to compliation/linking address -
CONFIG_ARMV7_SECURE_BASE.
When compile the PSCI code and link it into the u-boot image,
there will be relocation entries in .rel.dyn section for PSCI.
Actually, we do not needs these relocation entries.
If still keep the relocation entries in .rel.dyn section,
r0 at line 103 and 106 in arch/arm/lib/relocate.S may be an invalid
address which may not support read/write for one SoC.
102 /* relative fix: increase location by offset */
103 add r0, r0, r4
104 ldr r1, [r0]
105 add r1, r1, r4
106 str r1, [r0]
So discard them to avoid touching the relocation entry in
arch/arm/lib/relocate.S.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
p2371-2180 is the engineering board name for the Jetson TX1 developer
kit. Update Kconfig description and help text to make this obvious to
everyone.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rename GPU functions to less generic names to avoid potential name
collisions.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable the GPU node in the system-wide ft_system_setup() hook instead of
the board-specific ft_board_hook(). This allows us to enable GPU per SoC
generation instead of per-board as we did initially.
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There is no justification for this function, especially in exported
form.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add code to detect timeouts when waiting for HW events such as PLL
lock done. Any errors are logged and trigger an error return code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the tables defining which pads and mux options exist in the Tegra210
XUSB padctl hardware.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This change simply deletes code from the Tegra210 XUSB padctl driver that
is already present in the common XUSB padctl code. Since all the arrays
in tegra210_socdata are empty, this update may leave the Tegra210 XUSB
padctl driver non-functional at run-time. However, (a) this driver is not
used yet so no regression can be observed and (b) the next commit will
immediately fix this up.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There are some differences between the Tegra124 and Tegra210 XUSB padctl
code. So far, the common XUSB padctl code only supports Tegra124. Add
some parameters etc. so that it can work for both chips.
This also allows moving Tegra124's process_nodes() into the common file;
something that would have requires edits during the move if done in the
previous commit.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A fair amount of the XUSB padctl driver will be common between Tegra124
and Tegra210. To avoid cut/paste between the two chips, create a new
file that will contain the common code, and convert the Tegra124 code to
use it. This change doesn't move every last piece of code that can/will be
shared, but rather concentrates on moving code that can be moved with zero
changes, so there are no other diffs mixed in.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This file defines pr_fmt(), so the individual error() calls don't need to
include the prefix in their format strings. Doing so results in duplicate
text in any error messages. Remove the duplication.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A future patch will soon move some of the XUSB padctl code into a common
file in arch/arm/mach-tegra. Rename the existing dummy XUSB padctl file
to avoid conflicting with that, or being confusing.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
p2371-2180 has two PCI ports; a regular x4 slot and a x1 M.2 slot. This
patch adds the relevant DT to enable the PCI controller and configure
the XUSB padctl pin muxing, and code to turn on the PCI power and enable
PCI features in U-Boot. I have only tested the x4 slot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra210's PCI controller is largely identical to Tegra124, and hence
shares the same binding. However, it has a unique compatible value due
to the existence of at least one new HW bug that would prevent any driver
for a previous HW version from operating correctly.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Implement the procedure that the TRM mandates to initialize PLLREFE and
PLLE. This makes the PLL actually lock.
Note that this section of the TRM is being cleaned up to remove some
confusion. The set of register accesses in this patch should be final,
although the step numbers/descriptions might still change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add 10m50 devboard support. It is based on the Golden Hardware
Reference Design (GHRD), available at,
http://rocketboards.org/foswiki/view/Documentation/
AlteraMAX1010M50RevCDevelopmentKitLinuxSetup
Though we supported only one nios2-generic board in the past. Now,
with the removal of the nios2-generic board dir, adding new nios2
boards to u-boot is easier than before. It should be helpful to
add those boards supported in Linux mainline. There are only two
such nios2 boards, the 3c120 devboard and 10m50 devboard. The
nios2-generic is actually 3c120, and should restore the name. The
10m50 is this one.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
The latest Linux can directly handle SMP operations for UniPhier SoCs
without any help of U-boot. Drop the relevant code from U-boot.
See commit b1e4006aeda8c8784029de17d47987c21ea75f6d ("ARM: uniphier:
rework SMP operations to use trampoline code") in Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
