Commit Graph

156 Commits

Author SHA1 Message Date
Masahiro Yamada
ce480791f7 ARM: uniphier: add CONFIG_PREBOOT
For more boot-flow flexibility,

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-29 11:38:35 +09:00
Masahiro Yamada
9f9edb6fe3 ARM: uniphier: allow to source boot script before distro-boot
Some users might need additional setups before booting the kernel.
If there is found a file 'boot.scr', run it before invoking the
distro boot command.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-29 11:38:34 +09:00
Masahiro Yamada
6bc50a8f69 ARM: uniphier: do not modify bootcmd environment variable at run-time
Some users might want to modify 'bootcmd' at compile-time by editing
include/configs/uniphier.h, but overwriting it at run-time makes it
impossible.

Instead, set 'bootdev' at run-time, which contains the boot device the
system is booting from, then indirectly reference it from 'bootcmd'.

It is up to users whether to override 'bootcmd'.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-29 11:38:33 +09:00
Adam Ford
2fe88d4522 Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig
This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-19 19:19:50 -04:00
Masahiro Yamada
1a4bd3a095 ARM: uniphier: increase CONFIG_SYS_MONITOR_LEN again
With the migration to distro-boot, the size of the U-Boot proper
image for uniphier_v7_defconfig exceeded the current limit, 576KB.
Increase it to 832KB.

CONFIG_SYS_UBOOT_BASE must be moved as well to avoid the image
over-wrap because the boot ROM of Pro4, Pro5, PXs2/LD6b loads
the SPL to the physical address 0x100000.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11 20:37:16 +09:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Masahiro Yamada
7ef5b1e7ed ARM: uniphier: enable distro boot
Switch to the distro boot for UniPhier platform.

 - Remove the environment vairalbes used to load images from raw
   block devices.

 - Keep the command to download images via tftp.  This will be
   useful to boot the kernel when no valid kernel image is ready
   yet in the file system.

 - Use root.cpio.gz instead of root.cpio.uboot because we always know
   the file size of the init ramdisk; it is loaded via either a file
   system or network.

 - Rename fit_addr_r to kernel_addr_r, which the distro command
   checks to get the load address of FIT image.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-07-25 08:47:53 +09:00
Adam Ford
9c5b00973b Convert CONFIG_MTD_PARTITIONS et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MTD_PARTITIONS
   CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-22 19:20:17 -04:00
Masahiro Yamada
8c09f1f4fc ARM: uniphier: rename environment variable fdt_file to fdtfile
For booting Linux in the generic distro mechanism, cmd/pxe.c
retrieves the FDT file name from "fdtfile" environment variable.

Rename "fdt_file" to "fdtfile" for easier migration to distro boot.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-05-23 00:32:39 +09:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Masahiro Yamada
3ce5b1a8d8 ARM: uniphier: move SPL stack address
Currently, the address region, 0xf8000 - 0x100000, is used for SPL
stack for the 32bit SoCs.  Because the U-Boot proper image starts
from 0x70000, the maximum size of the U-Boot proper image is 544KB
(0x70000 - 0xf8000) for the NOR boot mode.  Now uniphier_v7_defconfig
is almost hitting this size limit.  Changing CONFIG_SPL_STACK can
raise the size limit with less impact.  With this, the size limit
will increase to 576KB (0x70000 - 0x100000).  If we need to increase
it even more, we would be able to change CONFIG_SYS_UBOOT_BASE at the
cost of the flashing command changes.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-04-24 00:35:35 +09:00
Masahiro Yamada
fbe73dc88d ARM: uniphier: select a correct mmc device before flashing images
Some boards support an SD card and an eMMC device at the same time.
Since both belong to 'mmc', they are identified by a device number.
When the device number of the eMMC is 1 instead 0, "mmc dev" command
must be performed to switch the target device before flashing images.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-04-24 00:35:35 +09:00
Masahiro Yamada
58d702274c ARM: uniphier: increase CONFIG_SYS_MONITOR_LEN
With the recent changes, the size of the U-Boot proper image for
uniphier_v7_defconfig exceeded the current limit, 512KB, then SPL
fails to load the whole of the U-Boot proper.  Increase the size.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-04-24 00:33:57 +09:00
Tom Rini
6f6b7cfa89 Convert all of CONFIG_CONS_INDEX to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-16 10:28:52 -04:00
Masahiro Yamada
27fbdcdefd ARM: uniphier: change load addresses for bigger kernel image
The kernel size is getting bigger and bigger.  Because the Android
common kernel is even bigger than the vanilla one, so images overlap
in the current memory layout.

Adjust the load address for a bigger kernel image.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-15 22:43:35 +09:00
Masahiro Yamada
34be347999 ARM: uniphier: increase the firmware size in update command environment
If a bigger EL32 is used, fip.bin can be larger than the currently
assumed boot firmware size.  Adjust the update commands.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-15 22:41:31 +09:00
Adam Ford
d021e94210 Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23 21:41:49 -05:00
Tom Rini
75670c81e4 configs: Migrate CONFIG_SPL_FRAMEWORK
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig.  We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important.  In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-14 12:14:13 -05:00
Masahiro Yamada
a322eb9ff6 ARM: uniphier: hide memory top by platform hook instead of CONFIG
I do not see a good reason to do this by a CONFIG option that affects
all SoCs.  The ram_size can be adjusted by dram_init() at run-time.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-01-09 21:58:19 +09:00
Masahiro Yamada
7e3caa81e0 Move CONFIG_PANIC_HANG to Kconfig
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-26 13:10:24 -05:00
Masahiro Yamada
a27bcbf815 ARM: uniphier: remove unused NAND CONFIG options
The Denali NAND driver does not use these options any more.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:29:00 +09:00
Masahiro Yamada
15d0f3538a ARM: uniphier: remove verify=n from environments
If the environment "verify" is set to n, the image verification
is entirely skipped.  Remove it as a preparation for verified boot.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23 01:02:05 +09:00
Masahiro Yamada
571e050b45 ARM: uniphier: increase CONFIG_SYS_BOOTM_LEN to 32MB
The default value of CONFIG_SYS_BOOTM_LEN, 0x800000, causes error
when uncompressing Image.gz out of FIT image.

   Uncompressing Kernel Image ... Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23 01:02:05 +09:00
Adam Ford
8daec2d9d3 net: Add SMC911X driver to Kconfig, convert
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
   CONFIG_SMC911X
   CONFIG_SMC911X_BASE
   CONFIG_SMC911X_16_BIT
   CONFIG_SMC911X_32_BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20 21:40:26 -04:00
Thomas Petazzoni
1f20fc53b3 include/configs: drop default definitions of CONFIG_SYS_MAXARGS
Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-03 15:30:29 -04:00
Thomas Petazzoni
432e398068 include/configs: drop default definitions of CONFIG_SYS_PBSIZE
Now that the fallback value of CONFIG_SYS_PBSIZE in
include/config_fallbacks.h has been adjusted, remove its definition
from a large number of board configuration files.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-03 15:30:28 -04:00
Adam Ford
e3f24d4f2c Kconfig: Add EEPROM options to Kconfig when I2C_EEPROM is set
Add the following options to drivers/misc/Kconfig:
	SYS_I2C_EEPROM_ADDR
	SYS_I2C_EEPROM_BUS
	SYS_EEPROM_SIZE
	SYS_EEPROM_PAGE_WRITE_BITS
	SYS_EEPROM_PAGE_WRITE_DELAY_MS
	SYS_I2C_EEPROM_ADDR_LEN
	SYS_I2C_EEPROM_ADDR_OVERFLOW

This does not migrate any boards, but provides a foundations for
those who want/need these options

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate uniphier]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-02 15:50:30 -04:00
Masahiro Yamada
8de11a5eef ARM: uniphier: remove unneeded NAND config options
CONFIG_NAND_DENALI select's CONFIG_SYS_NAND_SELF_INIT, so the
NAND initialization process is driven by the driver itself.
CONFIG_SYS_NAND_MAX_CHIPS and CONFIG_SYS_NAND_BASE are unused.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-30 09:03:11 +09:00
Masahiro Yamada
00aa453ebf ARM: uniphier: remove sLD3 SoC support
This SoC is too old.  It is difficult to maintain any longer.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-08-20 23:05:39 +09:00
Bin Meng
2931342874 configs: Remove CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS in all boards
Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
2017-07-28 23:34:23 +02:00
Masahiro Yamada
ee8d037ce7 ARM: uniphier: remove SPL support for ARMv8 SoCs
It has been a while since ARM Trusted Firmware supported UniPhier SoC
family.  U-Boot SPL was intended as a temporary loader that runs in
secure world.  It is a maintenance headache to support two different
boot mechanisms.  Secure firmware is realm of ARM Trusted Firmware
and now U-Boot only serves as a non-secure boot loader for UniPhier
ARMv8 SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-07-26 22:27:15 +09:00
Simon Glass
2be296538e Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25 21:08:01 -04:00
Tom Rini
91d27a17c6 Kconfig: Migrate FS_FAT / FAT_WRITE
Now that these symbols are in Kconfig, migrate all users.  Use imply on
a number of platforms that default to having this enabled.  As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-03 17:55:34 -04:00
Ley Foon Tan
0680f1b1f7 Convert CONFIG_SPL_BOARD_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_BOARD_INIT

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 07:29:48 -04:00
Masahiro Yamada
edee114a8b ARM: uniphier: move kernel physical base to 0x82080000
Reserve enough space below the kernel base.
The assumed address map is:
  80000000 - 80ffffff : for IPP
  81000000 - 81ffffff : for ARM secure
  82000000 -          : for Linux

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-17 21:51:04 +09:00
Masahiro Yamada
8d3064d9a9 ARM: uniphier: add usbupdate command
This script command will be useful to update boot images in the
USB storage.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-17 21:46:20 +09:00
Philipp Tomsich
f40574e2d7 Kconfig: Migrate CONFIG_BAUDRATE
Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-19 14:48:37 -04:00
Masahiro Yamada
7728f0c68d ARM: uniphier: rename second stage loader name
For the memory footprint reason, the Boot ROM can not load the ARM
Trusted Firmware BL1 directly when Trusted Board Boot is enabled.
The second stage loader is Socionext's own firmware, so rename it
for clarification.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-23 08:37:56 +09:00
Masahiro Yamada
e856bdcfb4 flash: complete CONFIG_SYS_NO_FLASH move with renaming
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH".  Flipping the logic will
make the code more readable.  Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
    common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
  find . -path './configs/*_defconfig' | xargs sed -i \
  -e '/CONFIG_SYS_NO_FLASH=y/d' \
  -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
  find . -name '*.[ch]' | xargs sed -i \
  -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
  -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
  -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
  -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
  - Rename the rest of instances
  - Remove the description from README
  - Create the new Kconfig entry in drivers/mtd/Kconfig
  - Remove the old Kconfig entry from common/Kconfig
  - Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-12 14:30:25 -05:00
Masahiro Yamada
e9d33e7326 cmd: move CONFIG_CMD_UNZIP and CONFIG_CMD_ZIP to Kconfig
CONFIG_CMD_ZIP is not defined by any board.  I am moving
CONFIG_CMD_UNZIP to defconfig files except UniPhier SoC family.

I am the maintainer of UniPhier platform, so I know "select CMD_UNZIP"
is better for this platform.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
2017-02-08 16:24:28 -05:00
Masahiro Yamada
54925327fa mmc: move CONFIG_GENERIC_MMC to Kconfig
Now, CONFIG_GENERIC_MMC seems equivalent to CONFIG_MMC.

Let's create an entry for "config GENERIC_MMC" with "default MMC",
then convert all macro defines in headers to Kconfig.  Almost all
of the defines will go away.

I see only two exceptions:
  configs/blanche_defconfig
  configs/sandbox_noblk_defconfig

They define CONFIG_GENERIC_MMC, but not CONFIG_MMC.  Something
might be wrong with these two boards, so should be checked later.

Anyway, this is the output of the moveconfig tool.

This commit was created as follows:

[1] create a config entry in drivers/mmc/Kconfig

[2] tools/moveconfig.py -r HEAD GENERIC_MMC

[3] manual clean-up of garbage comments in doc/README.* and
    include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-31 21:50:47 +09:00
Masahiro Yamada
b7b4303642 ARM: uniphier: make update commands more flexible for ATF
Currently, SPL (u-boot-spl.bin) and U-Boot (u-boot.bin) are stored
in non-volatile devices, and some environments are defined to update
the images easily.

When ARM Trusted Firmware is fully used, SPL is not used.  U-Boot
proper is contained as BL33 into FIP (Firmware Image Package), which
is standard container used by ATF.  Allow to use it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-29 20:59:08 +09:00
Masahiro Yamada
c0efc3140e ARM: uniphier: change CONFIG_SPL_PAD_TO to 128KB
The Boot ROM supports authentication feature to prevent malformed
software from being run on products.  The signature is added at the
tail of the second stage loader (= SPL in U-boot terminology).

The size of the second stage loader was 64KB, and it was consistent
across SoCs.  The situation changed when LD20 SoC appeared; it loads
80KB second stage loader, and it is the only exception.

Currently, CONFIG_SPL_PAD_TO is set to 64KB and U-Boot proper is
loaded from the 64KB offset of non-volatile devices.  This means the
signature of LD20 SoC (located at 80KB offset) corrupts the U-Boot
proper image.

Let's move the U-Boot proper image to 128KB offset.  It uses 48KB
for nothing but padding, and we could actually locate the U-Boot
proper at 80KB offset.  However, the power of 2 generally seems a
better choice for the offset address.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-29 20:59:08 +09:00
Masahiro Yamada
0b93e3de1e ARM: uniphier: change the offset to environment storage area
When ARM Trusted Firmware is used, bl1.bin + fip.bin exceeds 512KB,
so the boot image and the current environment area will overlap.
Move the environment storage to 1MB offset.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-29 20:59:08 +09:00
Masahiro Yamada
c0df1fafd7 ARM: uniphier: set initrd_high environment to skip initrd relocation
The boot_ramdisk_high() checks the environment "initrd_high" and,
if it is set to (ulong)-1, skip the initrd relocation.  This is
useful for faster booting when we know the initrd is already located
within the reach of the kernel.

Change "norboot" to copy images in order to make it work without
depending on the automatic relocation.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-29 20:59:08 +09:00
Masahiro Yamada
99b8517037 ARM: uniphier: use Image.gz instead Image for booting ARM64 Linux
The ARM64 Linux raw image now amounts to 15MB and it is getting
bigger and bigger.  Using Image.gz saves about 8MB.  The cost of
unzip is smaller than what we get by saving the kernel loading
from non-volatile devices.

The ARM32 Linux still uses zImage, a self-decompressor image,
so it should not be affected.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-29 20:59:08 +09:00
Masahiro Yamada
3e0cfaa05d ARM: uniphier: collect SPL CONFIG symbols to the bottom of header
For clarification, move CONFIG symbols that affect SPL building
into a single place.  Drop #ifdef CONFIG_SPL ... #endif since it is
harmless to define CONFIG_SPL_... during U-Boot proper building.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-29 20:59:08 +09:00
Masahiro Yamada
3e9952be23 ARM: uniphier: detect RAM size by decoding HW register instead of DT
U-Boot needs to set up available memory area(s) in dram_init() and
dram_init_banksize().  It is platform-dependent how to detect the
memory banks.  Currently, UniPhier adopts the memory banks _alleged_
by DT.  This is based on the assumption that users bind a correct DT
in their build process.

Come to think of it, the DRAM controller has already been set up
before U-Boot is entered (because U-Boot runs on DRAM).  So, the
DRAM controller setup register seems a more reliable source of any
information about DRAM stuff.  The DRAM banks are initialized by
preliminary firmware (SPL, ARM Trusted Firmware BL2, or whatever),
so this means the source of the reliability is shifted from Device
Tree to such early-stage firmware.  However, if the DRAM controller
is wrongly configured, the system will crash.  If your system is
running, the DRAM setup register is very likely to provide the
correct DRAM mapping.

Decode the SG_MEMCONF register to get the available DRAM banks.
The dram_init() and dram_init_banksize() need similar decoding.
It would be nice if dram_init_banksize() could reuse the outcome
of dram_init(), but global variables are unavailable at this stage
because the .bss section is available only after the relocation.
As a result, SG_MEMCONF must be checked twice, but a new helper
uniphier_memconf_decode() will help to avoid code duplication.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-29 20:59:08 +09:00
Patrick Delaunay
b0cf733933 disk: convert CONFIG_DOS_PARTITION to Kconfig
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2017-01-28 08:47:34 -05:00
Masahiro Yamada
561ca649a8 ARM: uniphier: make SPL optional for ARVv8 SoCs
We may want to run different firmware before running U-Boot.  For
example, ARM Trusted Firmware runs before U-Boot, making U-Boot
a non-secure world boot loader.  In this case, the SoC might be
initialized there, which enables us to skip SPL entirely.

This commit removes "select SPL" to make it configurable.  This
also enables the Multi SoC support for the UniPhier ARMv8 SoCs.
(CONFIG_ARCH_UNIPHIER_V8_MULTI)  Thanks to the driver model and
Device Tree, the U-Boot proper part is now written in a generic way.
The board/SoC parameters reside in DT.  The Multi SoC support
increases the memory footprint a bit, but the U-Boot proper does
not have strict memory constraint.  This will mitigate the per-SoC
(sometimes per-board) defconfig burden.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-01-22 15:11:12 +09:00