Move CONFIG_PANIC_HANG to Kconfig

Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This commit is contained in:
Masahiro Yamada 2017-12-04 12:37:00 +09:00 committed by Tom Rini
parent 48a346061d
commit 7e3caa81e0
49 changed files with 60 additions and 48 deletions

10
README
View File

@ -2168,16 +2168,6 @@ The following options need to be configured:
currently only supports clearing the memory.
- Error Recovery:
CONFIG_PANIC_HANG
Define this variable to stop the system in case of a
fatal error, so that you have to reset it manually.
This is probably NOT a good idea for an embedded
system where you want the system to reboot
automatically as fast as possible, but it may be
useful during development since you can try to debug
the conditions that lead to the situation.
CONFIG_NET_RETRY_COUNT
This variable defines the number of retries for

View File

@ -11,6 +11,7 @@ config ARCH_LS1012A
select SYS_FSL_ERRATUM_A009008
select ARCH_EARLY_INIT_R
select BOARD_EARLY_INIT_F
imply PANIC_HANG
config ARCH_LS1043A
bool
@ -91,6 +92,7 @@ config ARCH_LS1088A
select ARCH_EARLY_INIT_R
select BOARD_EARLY_INIT_F
imply SCSI
imply PANIC_HANG
config ARCH_LS2080A
bool
@ -129,6 +131,7 @@ config ARCH_LS2080A
select SYS_FSL_ERRATUM_A009203
select ARCH_EARLY_INIT_R
select BOARD_EARLY_INIT_F
imply PANIC_HANG
config FSL_LSCH2
bool

View File

@ -29,6 +29,7 @@ config TARGET_B4420QDS
select ARCH_B4420
select SUPPORT_SPL
select PHYS_64BIT
imply PANIC_HANG
config TARGET_B4860QDS
bool "Support B4860QDS"
@ -36,6 +37,7 @@ config TARGET_B4860QDS
select BOARD_LATE_INIT if CHAIN_OF_TRUST
select SUPPORT_SPL
select PHYS_64BIT
imply PANIC_HANG
config TARGET_BSC9131RDB
bool "Support BSC9131RDB"
@ -57,6 +59,7 @@ config TARGET_C29XPCIE
select SUPPORT_SPL
select SUPPORT_TPL
select PHYS_64BIT
imply PANIC_HANG
config TARGET_P3041DS
bool "Support P3041DS"
@ -64,6 +67,7 @@ config TARGET_P3041DS
select ARCH_P3041
select BOARD_LATE_INIT if CHAIN_OF_TRUST
imply CMD_SATA
imply PANIC_HANG
config TARGET_P4080DS
bool "Support P4080DS"
@ -71,6 +75,7 @@ config TARGET_P4080DS
select ARCH_P4080
select BOARD_LATE_INIT if CHAIN_OF_TRUST
imply CMD_SATA
imply PANIC_HANG
config TARGET_P5020DS
bool "Support P5020DS"
@ -78,6 +83,7 @@ config TARGET_P5020DS
select ARCH_P5020
select BOARD_LATE_INIT if CHAIN_OF_TRUST
imply CMD_SATA
imply PANIC_HANG
config TARGET_P5040DS
bool "Support P5040DS"
@ -85,6 +91,7 @@ config TARGET_P5040DS
select ARCH_P5040
select BOARD_LATE_INIT if CHAIN_OF_TRUST
imply CMD_SATA
imply PANIC_HANG
config TARGET_MPC8536DS
bool "Support MPC8536DS"
@ -101,6 +108,7 @@ config TARGET_MPC8541CDS
config TARGET_MPC8544DS
bool "Support MPC8544DS"
select ARCH_MPC8544
imply PANIC_HANG
config TARGET_MPC8548CDS
bool "Support MPC8548CDS"
@ -124,6 +132,7 @@ config TARGET_MPC8572DS
# Use DDR3 controller with DDR2 DIMMs on this board
select SYS_FSL_DDRC_GEN3
imply SCSI
imply PANIC_HANG
config TARGET_P1010RDB_PA
bool "Support P1010RDB_PA"
@ -133,6 +142,7 @@ config TARGET_P1010RDB_PA
select SUPPORT_TPL
imply CMD_EEPROM
imply CMD_SATA
imply PANIC_HANG
config TARGET_P1010RDB_PB
bool "Support P1010RDB_PB"
@ -142,6 +152,7 @@ config TARGET_P1010RDB_PB
select SUPPORT_TPL
imply CMD_EEPROM
imply CMD_SATA
imply PANIC_HANG
config TARGET_P1022DS
bool "Support P1022DS"
@ -155,6 +166,7 @@ config TARGET_P1023RDB
bool "Support P1023RDB"
select ARCH_P1023
imply CMD_EEPROM
imply PANIC_HANG
config TARGET_P1020MBG
bool "Support P1020MBG-PC"
@ -163,6 +175,7 @@ config TARGET_P1020MBG
select ARCH_P1020
imply CMD_EEPROM
imply CMD_SATA
imply PANIC_HANG
config TARGET_P1020RDB_PC
bool "Support P1020RDB-PC"
@ -171,6 +184,7 @@ config TARGET_P1020RDB_PC
select ARCH_P1020
imply CMD_EEPROM
imply CMD_SATA
imply PANIC_HANG
config TARGET_P1020RDB_PD
bool "Support P1020RDB-PD"
@ -179,6 +193,7 @@ config TARGET_P1020RDB_PD
select ARCH_P1020
imply CMD_EEPROM
imply CMD_SATA
imply PANIC_HANG
config TARGET_P1020UTM
bool "Support P1020UTM"
@ -187,6 +202,7 @@ config TARGET_P1020UTM
select ARCH_P1020
imply CMD_EEPROM
imply CMD_SATA
imply PANIC_HANG
config TARGET_P1021RDB
bool "Support P1021RDB"
@ -195,6 +211,7 @@ config TARGET_P1021RDB
select ARCH_P1021
imply CMD_EEPROM
imply CMD_SATA
imply PANIC_HANG
config TARGET_P1024RDB
bool "Support P1024RDB"
@ -203,6 +220,7 @@ config TARGET_P1024RDB
select ARCH_P1024
imply CMD_EEPROM
imply CMD_SATA
imply PANIC_HANG
config TARGET_P1025RDB
bool "Support P1025RDB"
@ -256,6 +274,7 @@ config TARGET_T1023RDB
select SUPPORT_SPL
select PHYS_64BIT
imply CMD_EEPROM
imply PANIC_HANG
config TARGET_T1024RDB
bool "Support T1024RDB"
@ -264,6 +283,7 @@ config TARGET_T1024RDB
select SUPPORT_SPL
select PHYS_64BIT
imply CMD_EEPROM
imply PANIC_HANG
config TARGET_T1040QDS
bool "Support T1040QDS"
@ -272,6 +292,7 @@ config TARGET_T1040QDS
select PHYS_64BIT
imply CMD_EEPROM
imply CMD_SATA
imply PANIC_HANG
config TARGET_T1040RDB
bool "Support T1040RDB"
@ -280,6 +301,7 @@ config TARGET_T1040RDB
select SUPPORT_SPL
select PHYS_64BIT
imply CMD_SATA
imply PANIC_HANG
config TARGET_T1040D4RDB
bool "Support T1040D4RDB"
@ -288,6 +310,7 @@ config TARGET_T1040D4RDB
select SUPPORT_SPL
select PHYS_64BIT
imply CMD_SATA
imply PANIC_HANG
config TARGET_T1042RDB
bool "Support T1042RDB"
@ -304,6 +327,7 @@ config TARGET_T1042D4RDB
select SUPPORT_SPL
select PHYS_64BIT
imply CMD_SATA
imply PANIC_HANG
config TARGET_T1042RDB_PI
bool "Support T1042RDB_PI"
@ -312,6 +336,7 @@ config TARGET_T1042RDB_PI
select SUPPORT_SPL
select PHYS_64BIT
imply CMD_SATA
imply PANIC_HANG
config TARGET_T2080QDS
bool "Support T2080QDS"
@ -328,6 +353,7 @@ config TARGET_T2080RDB
select SUPPORT_SPL
select PHYS_64BIT
imply CMD_SATA
imply PANIC_HANG
config TARGET_T2081QDS
bool "Support T2081QDS"
@ -342,12 +368,14 @@ config TARGET_T4160QDS
select SUPPORT_SPL
select PHYS_64BIT
imply CMD_SATA
imply PANIC_HANG
config TARGET_T4160RDB
bool "Support T4160RDB"
select ARCH_T4160
select SUPPORT_SPL
select PHYS_64BIT
imply PANIC_HANG
config TARGET_T4240QDS
bool "Support T4240QDS"
@ -356,6 +384,7 @@ config TARGET_T4240QDS
select SUPPORT_SPL
select PHYS_64BIT
imply CMD_SATA
imply PANIC_HANG
config TARGET_T4240RDB
bool "Support T4240RDB"
@ -363,6 +392,7 @@ config TARGET_T4240RDB
select SUPPORT_SPL
select PHYS_64BIT
imply CMD_SATA
imply PANIC_HANG
config TARGET_CONTROLCENTERD
bool "Support controlcenterd"
@ -393,16 +423,19 @@ config TARGET_UCP1020
bool "Support uCP1020"
select ARCH_P1020
imply CMD_SATA
imply PANIC_HANG
config TARGET_CYRUS_P5020
bool "Support Varisys Cyrus P5020"
select ARCH_P5020
select PHYS_64BIT
imply PANIC_HANG
config TARGET_CYRUS_P5040
bool "Support Varisys Cyrus P5040"
select ARCH_P5040
select PHYS_64BIT
imply PANIC_HANG
endchoice

View File

@ -35,4 +35,5 @@ CONFIG_SYS_NS16550=y
CONFIG_FSL_ESPI=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
CONFIG_PANIC_HANG=y
CONFIG_OF_LIBFDT=y

View File

@ -43,4 +43,5 @@ CONFIG_FSL_ESPI=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
CONFIG_FS_CRAMFS=y
CONFIG_PANIC_HANG=y
CONFIG_OF_LIBFDT=y

View File

@ -43,4 +43,5 @@ CONFIG_FSL_ESPI=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
CONFIG_FS_CRAMFS=y
CONFIG_PANIC_HANG=y
CONFIG_OF_LIBFDT=y

View File

@ -39,3 +39,4 @@ CONFIG_DM_SPI=y
CONFIG_ATCSPI200_SPI=y
CONFIG_TIMER=y
CONFIG_ATCPIT100_TIMER=y
CONFIG_PANIC_HANG=y

View File

@ -24,4 +24,5 @@ CONFIG_DOS_PARTITION=y
CONFIG_NETDEVICES=y
CONFIG_E1000=y
CONFIG_SYS_NS16550=y
CONFIG_PANIC_HANG=y
CONFIG_OF_LIBFDT=y

View File

@ -40,4 +40,5 @@ CONFIG_NAND=y
CONFIG_SPL_NAND_SIMPLE=y
CONFIG_SYS_NS16550=y
CONFIG_BCH=y
CONFIG_PANIC_HANG=y
CONFIG_OF_LIBFDT=y

View File

@ -39,4 +39,5 @@ CONFIG_NAND=y
CONFIG_SPL_NAND_SIMPLE=y
CONFIG_SYS_NS16550=y
CONFIG_BCH=y
CONFIG_PANIC_HANG=y
CONFIG_OF_LIBFDT=y

View File

@ -51,3 +51,4 @@ CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_GENERIC=y
CONFIG_USB_STORAGE=y
CONFIG_PANIC_HANG=y

View File

@ -54,3 +54,4 @@ CONFIG_USB_EHCI_GENERIC=y
CONFIG_USB_DWC3=y
CONFIG_USB_DWC3_UNIPHIER=y
CONFIG_USB_STORAGE=y
CONFIG_PANIC_HANG=y

View File

@ -51,3 +51,4 @@ CONFIG_USB_EHCI_GENERIC=y
CONFIG_USB_DWC3=y
CONFIG_USB_DWC3_UNIPHIER=y
CONFIG_USB_STORAGE=y
CONFIG_PANIC_HANG=y

View File

@ -27,4 +27,5 @@ CONFIG_DS4510=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_PHYLIB=y
CONFIG_SYS_NS16550=y
CONFIG_PANIC_HANG=y
CONFIG_OF_LIBFDT=y

View File

@ -28,4 +28,5 @@ CONFIG_CMD_PCA953X=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_PHYLIB=y
CONFIG_SYS_NS16550=y
CONFIG_PANIC_HANG=y
CONFIG_OF_LIBFDT=y

View File

@ -30,4 +30,5 @@ CONFIG_DS4510=y
CONFIG_MTD_NOR_FLASH=y
CONFIG_PHYLIB=y
CONFIG_SYS_NS16550=y
CONFIG_PANIC_HANG=y
CONFIG_OF_LIBFDT=y

View File

@ -30,4 +30,5 @@ CONFIG_PHYLIB=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_STORAGE=y
CONFIG_PANIC_HANG=y
CONFIG_OF_LIBFDT=y

View File

@ -173,7 +173,6 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM

View File

@ -117,7 +117,6 @@
#define CONFIG_SYS_MEMTEST_START 0x00200000
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_PANIC_HANG
/* DDR Setup */
#define CONFIG_DDR_SPD

View File

@ -69,7 +69,6 @@
#define CONFIG_SYS_MEMTEST_START 0x00010000 /* skip exception vectors */
#define CONFIG_SYS_MEMTEST_END 0x1f000000 /* skip u-boot at top of RAM */
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L2 Cache as L2 SRAM

View File

@ -46,7 +46,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_SYS_CCSRBAR 0xe0000000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR

View File

@ -58,7 +58,6 @@
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x7fffffff
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L2 Cache as L2 SRAM

View File

@ -215,7 +215,6 @@
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x1fffffff
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/* DDR Setup */
#define CONFIG_SYS_DDR_RAW_TIMING

View File

@ -52,8 +52,6 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x02000000
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/* Implement conversion of addresses in the LBC */
#define CONFIG_SYS_LBC_LBCR 0x00000000
#define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8

View File

@ -116,7 +116,6 @@ unsigned long get_board_sys_clk(unsigned long dummy);
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM

View File

@ -196,7 +196,6 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM

View File

@ -219,7 +219,6 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM

View File

@ -127,7 +127,6 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM

View File

@ -226,7 +226,6 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM

View File

@ -96,7 +96,6 @@
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM

View File

@ -136,7 +136,6 @@
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x1fffffff
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR

View File

@ -21,7 +21,6 @@
#define CONFIG_SKIP_TRUNOFF_WATCHDOG
#define CONFIG_CMDLINE_EDITING
#define CONFIG_PANIC_HANG
#define CONFIG_ARCH_MAP_SYSMEM

View File

@ -128,7 +128,6 @@
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM

View File

@ -89,7 +89,6 @@
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM

View File

@ -117,7 +117,6 @@
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_PANIC_HANG
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#include <asm/arch/soc.h>

View File

@ -223,8 +223,6 @@ unsigned long long get_qixis_addr(void);
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#ifdef CONFIG_SPL
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000

View File

@ -221,8 +221,6 @@ unsigned long long get_qixis_addr(void);
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
#define CONFIG_SPL_FRAMEWORK

View File

@ -270,7 +270,6 @@
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x1fffffff
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR

View File

@ -69,7 +69,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x1fffffff
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR

View File

@ -31,7 +31,6 @@
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/* Needed to fill the ccsrbar pointer */

View File

@ -54,7 +54,6 @@
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L3 Cache as L3 SRAM

View File

@ -90,7 +90,6 @@
/* hang() the board on panic() */
#define CONFIG_PANIC_HANG
/* environment placement (for NAND), is different for FLASHCARD but does not
* harm there */

View File

@ -218,8 +218,6 @@
/* for LD20; the last 64 byte is used for dynamic DDR PHY training */
#define CONFIG_SYS_MEM_TOP_HIDE 64
#define CONFIG_PANIC_HANG
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE)
/* only for SPL */

View File

@ -487,7 +487,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_CMDLINE_EDITING 1 /* Command-line editing */
#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */

View File

@ -291,7 +291,6 @@
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */

View File

@ -341,7 +341,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */

View File

@ -339,7 +339,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
#define CONFIG_PANIC_HANG /* do not reset board on panic */
#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */

View File

@ -130,10 +130,6 @@
#define CONFIG_MX_CYCLIC
#define CONFIG_SHOW_BOOT_PROGRESS
#ifdef DEBUG
#define CONFIG_PANIC_HANG 1 /* Require manual reboot */
#endif
/*=========================================*/
/* FPGA Registers (board info and control) */

View File

@ -45,6 +45,16 @@ config USE_TINY_PRINTF
The supported format specifiers are %c, %s, %u/%d and %x.
config PANIC_HANG
bool "Do not reset the system on fatal error"
help
Define this option to stop the system in case of a fatal error,
so that you have to reset it manually. This is probably NOT a good
idea for an embedded system where you want the system to reboot
automatically as fast as possible, but it may be useful during
development since you can try to debug the conditions that lead to
the situation.
config REGEX
bool "Enable regular expression support"
default y if NET