Commit a479f103dc ("hash: Allow for SHA512 hardware implementations")
defined function definitions for hardware accelerated SHA384 and SHA512.
If CONFIG_SHA_HW_ACCEL=y, these functions are used.
We already have boards using CONFIG_SHA_HW_ACCEL=y but none implements the
new functions hw_sha384() and hw_sha512().
For implementing the EFI TCG2 protocol we need SHA384 and SHA512. The
missing hardware acceleration functions lead to build errors on boards like
peach-pi_defconfig.
Introduce a new Kconfig symbol CONFIG_SHA512_HW_ACCEL to control if the
functions hw_sha384() and hw_sha512() shall be used to implement the SHA384
and SHA512 algorithms.
Fixes: a479f103dc ("hash: Allow for SHA512 hardware implementations")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Building 32bit boards with the TCG2 protocol enabled leads to a build
warning due to a missing conversion.
lib/efi_loader/efi_tcg2.c:774:27:
error: cast to pointer from integer of different size
[-Werror=int-to-pointer-cast]
774 | ret = tcg2_create_digest((u8 *)data_to_hash, data_to_hash_len,
| ^
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
'make htmldocs' results in a build warning
checking consistency... doc/usage/extension.rst:
WARNING: document isn't included in any toctree
Add the document to the index.
Fixes: 2f84e9cf06 ("cmd: add support for a new "extension" command")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Add base support for Marvell OcteonTX2 CN9130 DB (mostly done
by Kostya)
- Sync Armada 8k MMU setup with Marvell version (misc Marvell
authors)
- spi: kirkwood: Some fixes especially for baudrate generation
(misc Marvell authors)
- mvebu: x530: Reduce SPL image size (Stefan)
- Rename "rx_training" to "mvebu_comphy_rx_training" (Stefan)
Even if only USB gadget is defined, dwc3 generic driver enables
a definition and probe/remove functions for host driver.
This enables the definition if USB_HOST is enabled only.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
All newer Allwinner SoCs (since about 2013) miss the CONFIGDATA register
in their MUSB implementation, so they need a quirk to hardcode this.
Currently this quirk depends on listing the SoCs affected in musb_reg.h,
which means that this list needs to grow with every new chip.
Move the quirk feature into Kconfig, next to PIO_ONLY, and change the
default to y (for Allwinner builds), while listing the early
implementations as exceptions.
This fixes USB peripheral operation on some newer SoCs, which were not
explicitly listed before.
Tested on H6, H616, R40 (which were broken before), and also on the H5
and A20, for regressions.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch adds the base support for the Marvell Octeon TX2 CN913x DB.
Only one defconfig is added with this patch. Other board variants are
available (NAND, MMC booting) and images for these boards can be
generated by following the documentation added in the included README.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the dtsi/dts files needed to support the Marvell
Octeon TX2 CN913x DB. This is only the base port with not all
interfaces supported fully.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Rename the misleading cmd "rx_training" to "mvebu_comphy_rx_training" to
avoid confusion and mixup with DDR3/4 training. This makes it clear,
that this command is platform specific and handles the COMPHY RX
training.
Also depend this cmd on ARMADA_8K and not TARGET_MVEBU_ARMADA_8K to make
is available for OcteonTX2 CN913x.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pali Rohár <pali@kernel.org>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Marek Behún <marek.behun@nic.cz>
Acked-by: Pali Rohár <pali@kernel.org>
The pcie_dw_mvebu configure ATU regions for memory, configuration
and IO space types. However the latter is not obligatory
and when not specified in the device tree, causes wrong
ATU configuration. Fix that by adding a dependency on the
detected PCIE regions count.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/18136
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>
Some of the setups including cn9130 opens mmio window starting from
0xc0000000, reflect it in the u-boot code.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
There is region left by ATF, which needs to remain in memory to provide RT
services. To prevent overwriting it by u-boot, do not provide any mapping
for this memory region, so any attempt to access it will trigger
synchronous exception.
Update sr 2021-04-12:
Don't update armada3700/cpu.c mmu table, as this has specific changes
included in mainline.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
After commit 1fe929ed497bcc8975be8d37383ebafd22b99dd2
("spi: kirkwood: prevent configuring speed exceeding max controller freq")
the spi frequency could be set to 0 on platform where spi-max-frequency
is not defined (e.g. on armada-388-gp). Prevent limiting speed in
mentioned cases.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Marcin Wojtas <marcin@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a limitation in the kirkwood_spi driver
set_speed hook, which prevents setting too high transfer
speed.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The Armada SoC family implementation of this SPI hardware module has
extended the configuration register to allow for a wider range of SPI
clock rates. Specifically the Serial Baud Rate Pre-selection bits in the
SPI Interface Configuration Register now also use bits 6 and 7 as well.
Modify the baud rate calculation to handle these differences for the
Armada case. Potentially a baud rate can be setup using a number of
different pre-scalar and scalar combinations. This code tries all
possible pre-scalar divisors (8 in total) to try and find the most
accurate set.
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently, building U-Boot for x530 fails since the SPL image is too
big. This patch reduces the SPL size by changing the following Kconfig
options:
Enable CONFIG_SPL_TINY_MEMSET
Disable CONFIG_SPI_FLASH_BAR
By disabling CONFIG_SPI_FLASH_BAR, the tiny SPI NOR framework can be
used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
When the PHY interface is set as TXID & RXID, the delays should be taken from DT,
but first they should not be hardcoded since the PHY driver will set them.
Fixes: 798424e857 ("net: designware: add Amlogic Meson8b & later glue driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If the PHY isn't specified in the DT, -ENODATA means it should be skipped,
handle it like -ENOENT.
With that, devices without USB3 supported can have USB working (Odroid-HC4).
Fixes: adb049abf7 ("usb: dwc3: Add Meson G12A USB Glue")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This lacks the right u-boot specific DT include to make HDMI work.
Reported-by: B1oHazard <ty3uk@mail.ua>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This reverts commit bc8bbb77f7.
This commit breaks U-Boot booting on SiFive Unleashed board, as
there is no such CSR on U54 core.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The pwm_sifive_set_config() and pwm_sifive_set_enable() cannot work
properly due to the wrong implementations. It will cause the u-boot
PWM command to not work as expected. The bugs will be resolved in this
patch.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Testing showed that disabling AI while leaving PLL1 enabled disabled the
aisram. This suggests that AI is a more appropriate clock for that ram
bank.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This is more consistent with the naming of other ram banks, and matches
what Linux is doing.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
We just need to initialize all the clocks pre-reloc. The clock driver
creates a bunch of devices, so we need to increase the pre-reloc malloc
arena.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
These devices are necessary for the clock driver, which is required by the
sram driver, to run pre-relocation.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Variables which had previously been stored in .bss are moved to .data. In
addition, probed needs to be reset when the clock driver is re-bound
post-relocation.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
No other (real) clocks have the cpu clock as their parent; instead they are
children of aclk. Move the clint clock under aclk to match them.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This simplifies the PLL creation process, since we don't have to pass all
the parameters individually.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This conditional always evaluated as false, regardless of the value of reg.
Fix it so that it properly tests the bits in the PLL register. Also test
PLL_EN, now that we set it.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
After starting or setting the rate of a PLL, the enable bit must be set.
This fixes a bug where the AI ram would not be accessible, because it
requires PLL1 to be running.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
If the user/dev explicitly requests a clock be assigned a certain rate,
then we should warn them if we can't do it. This makes it clear if the
clock is running at the default rate.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Update the Kconfig and the board file to make the am335x board compatible
with cape detection.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
The am335x from BeagleBone use i2c EEPROM to detect capes.
The memory is wired to i2c bus 2 therefore it need to be enabled.
Add i2c2 clock, pinmux description and pinmux enable function.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
This commit enables using the extension board detection mechanism on
CHIP boards
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Add the extension_board_scan specific function to scan the information
of the EEPROM on one-wire and fill the extension struct.
Add the Kconfig symbol to enable the needs to detect DIPs.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Andre Przywara <andre.przywara@arm.com>
This patch changes the functioning of the detection of w1 devices.
The old way was a comparison between detected w1 and the ones described in
the device tree. Now it will just look for the driver matching the family
id of the w1 detected.
The patch is inspired from Maxime Ripard code.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
The BeagleBone platforms all use a common mechanism to discover and
identify extension boards (called "capes"): each extension board has an
I2C-connected EEPROM describing itself.
This patch implements a generic extension_scan_board() feature that can
be used by all BeagleBone platforms to read those I2C EEPROMs and fill
in the list of "extension" structures.
Following commits will enable this common logic on two BeagleBone
platforms.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
