Commit Graph

50 Commits

Author SHA1 Message Date
Marek Vasut
5602330df0 ARM: rmobile: Add recovery SPL for R-Car Gen3
Build an SPL which can be started via SCIF download mode on R-Car Gen3
and allows loading and executing U-Boot uImage with the next stage code.
This is also useful for starting e.g. ATF BL2, which inits the hardware
and returns to the U-Boot SPL, which can then load e.g. U-Boot proper.

The H3, M3-W, M3-N SoCs have plenty of SRAM for storing the U-Boot SPL
while the payload, e.g. ATF BL2, executes, so there is no problem here.

However, E3 and D3 have much less SRAM, hence the loader uses a trick
where it copies itself beyond the area used by BL2 and executes from
there. That area is 32kiB large and not enough to hold U-Boot SPL, BSS,
stack and malloc area, so the later two are placed at +0x4000 offset
from start of SRAM, another area not used by ATF BL2. To make things
even more complicated, the SCIF loader cannot load to the upper 32kiB
of the SRAM directly, hence the copying approach.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-05-21 22:15:31 +02:00
Marek Vasut
b72d308c13 ARM: rmobile: Sync Gen3 defconfigs
Synchronize R-Car Gen3 defconfigs to remove duplicate pinctrl entries.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-05-21 22:15:31 +02:00
Marek Vasut
2548ca7d97 ARM: rmobile: Enable PCIe driver on R-Car Gen3 Salvator-X
Enable PCIe driver on R-Car Gen3 Salvator-X boards.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-05-21 22:15:31 +02:00
Marek Vasut
bdafee778d ARM: rmobile: Enable multi-DTB fit LZO compression
Enable LZO compression of the multi-DTB fitImages, since the U-Boot
with multiple DTs enabled is becoming quite large and the DTs can
be well compressed. The LZO compression saves almost 200 kiB on the
Salvator-X(S) and ULCB targets.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-04-09 18:19:10 +02:00
Marek Vasut
c3aa054568 ARM: rmobile: Sync Gen3 defconfigs
Synchronize Gen3 defconfigs in wake of the Kconfig option changes.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2019-02-25 16:07:41 +01:00
Tom Rini
1bac199e8c configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-07 18:11:00 -05:00
Marek Vasut
14ebe87b58 ARM: dts: Turn Salvator-X into Multi-DTB config
Bundle DTBs for R8A7795, R8A7796, R8A77965 Salvator-X variants
into the single U-Boot build and let U-Boot choose between them
based on the CPU model.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-04 09:21:07 +01:00
Marek Vasut
8e6442e3cd ARM: rmobile: Enable MMC HS400 on Salvator-X, ULCB, Ebisu
Enable the HS400 support code on H3, M3W, M3N Salvator-X(S)
and ULCB boards as well as E3 Ebisu board.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-03 12:51:17 +01:00
Hiroyuki Yokoyama
44c56bf824 ARM: rmobile: Remove console parameter from bootargs on Gen3
This patch removes 'console=' argument, because kernel uses
stdout-path as parameter.

Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
2018-10-18 19:07:46 +02:00
Tom Rini
8c5cad05c9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03 15:26:12 -04:00
Marek Vasut
1a6e8dda49 ARM: rmobile: Enable fitImage support on Gen3
Enable fitImage support to be on the right side of the millenium.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-04-17 11:38:55 +02:00
Marek Vasut
76af7e51e1 ARM: rmobile: Zap CONFIG_MMC_RENESAS_TUNING
Drop the CONFIG_MMC_RENESAS_TUNING symbol from Gen3 configs.
This symbol is no longer used after the Matsushita SDHI driver,
instead the renesas-sdhi driver uses CONFIG_MMC_HS200_SUPPORT
to discern whether the tuning support should be compiled in.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
--
V2: Submit this on top of configs which are actually in mainline
2018-04-14 00:03:30 +02:00
Marek Vasut
8af6737d45 ARM: rmobile: Enable HS200 mode on RCar Gen3
Enable the HS200 on RCar Gen3 platforms, since the SDHI core supports it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-04-11 23:11:59 +02:00
Marek Vasut
33f65ec83e ARM: rmobile: Switch to CONFIG_RENESAS_SDHI
Since the Renesas SDHI has it's own custom driver sharing the
common code with Uniphier one, adjust the Kconfig entries.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-04-11 23:11:56 +02:00
Adam Ford
d021e94210 Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23 21:41:49 -05:00
Marek Vasut
74caed0e33 ARM: rmobile: Enable DTO support on Gen3
Enable support for applying DT overlays on Gen3. This is convenient
for handling extra additional hardware, like ie. the Kingfisher.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-02-16 16:43:09 +01:00
Tom Rini
278b90ce78 configs: Migrate CONFIG_SYS_TEXT_BASE
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11 09:30:09 -05:00
Marek Vasut
34df58a95e ARM: dts: rmobile: Factor out U-Boot extras
Pull out u-boot extras into dtsi files to make synchronization of DTS
from Linux kernel as easy as a simple copy. All the U-Boot extras are
now in *-u-boot.dts* files instead.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-01-24 23:27:21 +01:00
Marek Vasut
02e80f0c11 ARM: rmobile: Migrate boards to RCar IIC drivers
Stop using the old ad-hoc SH I2C driver and use the new RCar IIC
driver instead. The SH I2C driver should be deprecated and removed
eventually.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:21 +01:00
Marek Vasut
d7f0b85269 ARM: rmobile: Use PRR driver on all Gen3 boards
Mark the PRR as u-boot,dm-pre-reloc in all Gen3 board DTs as it is
needed very early and turn on the CONFIG_SYSCON to allow the PRR
driver to bind as a syscon uclass.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:21 +01:00
Marek Vasut
796411b08a ARM: rmobile: Enable xHCI on RCar Gen3 boards
Enable the XHCI support on all boards.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Marek Vasut
8e8ebd3269 ARM: rmobile: Remove CONFIG_CMD_SDRAM from Salvator-X
This command is useless on Salvator-X as it is reading DRAM info from
SPD. We have no SPD on Salvator-X.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Tom Rini
2ee87b0c1a Merge branch 'rmobile' of git://git.denx.de/u-boot-sh 2017-10-10 20:14:38 -04:00
Tuomas Tynkkynen
ad12dc1844 cmd: Toggle the default value of CONFIG_CMD_IMLS
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-10 17:51:04 -04:00
Marek Vasut
55f6847138 ARM: rmobile: Enable pinconf
Enable pinconf since it's now implemented and used in the DTs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-10-04 08:50:43 +09:00
Marek Vasut
793afcde6c ARM: rmobile: Switch to DM PFC pinmux and GPIO driver
Enable the PFC pinmux and GPIO drivers and disable the SH GPIO combo
driver. This allows the drivers to obtain pinmux and GPIO configuration
from DT rather than hard-coding it in board files.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-28 06:54:06 +09:00
Marek Vasut
0e9b18c376 ARM: rmobile: Enable DM regulator support
Regulators are needed for the MMC framework to let it toggle the SD power.
Enable DM regulator support and support for fixed and GPIO regulator.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-28 06:51:37 +09:00
Marek Vasut
9ac9c341f9 ARM: rmobile: Switch to UniPhier SD driver on Gen3
The UniPhier SD driver handles the same Matsushita IP as is used
in the Renesas RCar SoCs, yet the driver is significantly better
than the SH SDHI one. Switch over to the Uniphier driver.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-28 06:38:30 +09:00
Marek Vasut
286056d28c ARM: rmobile: Enable GPIO command
This command is convenient for manipulating the GPIOs, so enable it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-24 14:13:05 +09:00
Marek Vasut
7208d903eb ARM: rmobile: Move CONFIG_CMD_ from rcar-gen3-common to configs
Just move those config options from macros to configs.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-24 14:12:07 +09:00
Marek Vasut
c54b0b754b ARM: rmobile: Enable EHCI generic on Salvator-X
Enable the EHCI generic driver, which is superior to ad-hoc SoC specific one.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-12 19:07:23 +02:00
Marek Vasut
25f840d7ef ARM: rmobile: Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
Disable CONFIG_ARCH_FIXUP_FDT_MEMORY to prevent U-Boot from modifying
the memory {} nodes in the DT passed to the Linux kernel. The R8A779x
DT contains multiple memory {} nodes, while U-Boot only modifies the
first one and stuffs all the memory entries into it, which is wrong.
Disabling CONFIG_ARCH_FIXUP_FDT_MEMORY is the least intrusive way to
fix the issue this close to the release, while the real fix is to
extend the fdt_fixup_memory_banks() to handle multiple memory nodes
in DT.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-09-07 20:04:41 -04:00
Tom Rini
5dc4dfd2a9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-28 07:16:32 -04:00
Marek Vasut
3345ca21a1 ARM: rmobile: Enable MMC and USB DM on Salvator-X
Enable the MMC and USB DM on the board since it's the modern method
and now supported by the drivers.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-26 07:04:49 +09:00
Marek Vasut
d47f356cde ARM: rmobile: Enable HUSH parser
The HUSH parser was disabled somewhere along the way, reenable it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexandru Gagniuc <alex.g@adaptrum.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-26 07:04:49 +09:00
Marek Vasut
c4464e163e ARM: rmobile: Enable KSZ90X1 PHY on Salvator-X
Commit da3b9e7fd6 (Move PHY_MICREL and PHY_MICREL_KSZ90X1 to Kconfig)
broke ethernet support on R8A779x Salvator-X boards by disabling the
KSZ90x1 PHY in Kconfig. Reenable it.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexandru Gagniuc <alex.g@adaptrum.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-26 07:04:49 +09:00
Tom Rini
88663126a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 20:00:40 -04:00
Sam Protsenko
5abc1a4523 common: Move CONFIG_BOOTARGS to Kconfig
Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 17:06:06 -04:00
Simon Glass
efce2442d3 Convert CONFIG_CMD_SDRAM to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_SDRAM

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:56 -04:00
Tom Rini
877a1a35b3 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-11 11:20:19 -04:00
Alexandru Gagniuc
da3b9e7fd6 Move PHY_MICREL and PHY_MICREL_KSZ90X1 to Kconfig
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:22:29 -05:00
Nobuhiro Iwamatsu
9c552db619 ARM: rmobile: Update defconfig of R-Car Gen3
This updates defconfig of R-Car Gen3 to keep with the latest Kconfig.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-03 04:29:23 +09:00
Marek Vasut
03a38a3972 serial: sh: Convert to Kconfig
Convert the SH Serial to Kconfig using tools/moveconfig.py tool
and a bit of manual adjustment to cater for failed conversions.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-03 04:26:24 +09:00
Marek Vasut
9a86226e27 ARM: rmobile: Enable clock framework on Salvator-X
Since there is now a clock driver for RCar Gen3, enable it on this board.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-03 04:26:24 +09:00
Marek Vasut
86fa69072d ARM: rmobile: Enable OF_CONTROL on RCar Gen3
Since the DTs are now in place, enable OF control so that they get
bundled into the U-Boot.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-08-03 04:26:18 +09:00
Simon Glass
2be296538e Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25 21:08:01 -04:00
Marek Vasut
b2330426c3 ARM: rmobile: Add missing config bits
The commit "fb82fe385173 configs: Resync defconfigs" resynced all config
files.  This exposed two latent issues with the Gen3 boards in that we
had not been setting CONFIG_DEFAULT_FDT_FILE correctly and had not been
setting CONFIG_CMD_MMC.  Fix both of these.

Fixes: fb82fe3851 ("configs: Resync defconfigs")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-20 14:23:17 -04:00
Tom Rini
fb82fe3851 configs: Resync defconfigs
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-19 09:47:40 -04:00
Tom Rini
91d27a17c6 Kconfig: Migrate FS_FAT / FAT_WRITE
Now that these symbols are in Kconfig, migrate all users.  Use imply on
a number of platforms that default to having this enabled.  As part of
this we must migrate some straglers for CMD_FAT and DOS_PARTITION.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-03 17:55:34 -04:00
Marek Vasut
adf3057f37 ARM: rmobile: salvator-x: Add R8A7796 support
Add minor ifdeffery and default board config for the Salvator-XS board
with R8A7796 M3 SoC.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-05-22 04:38:28 +09:00