This patch add ZyXEL NSA310S 1-Bay Media Server
The ZyXEL NSA310S device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1000Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 4 Status LED (green)
- 1 Copy/Sync button
- 1 Reset button
- 1 SATA II port
- 2 USB 2.0 ports (front and back)
- Smart fan
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
As some MVEBU platforms using the MVNETA driver seem to miss the
first ARP packet, lets reduce the timeout and increase the retry
count. This increases the speed for communication establishment.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
serial_init() reads global_data, since global_data is not yet
initialized, this can cause unwanted behaviour leading to QSPI XIP boot
hang. Also, since serial_init() is anyways called later from
boar_init_f(), it does not make sense to do the same in s_init().
Tested on AM437x IDK EVM with QSPI XIP boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.
The dts file is identical to the one submitted upstream.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These files are based on the current latest upstream kernel work. The
bus_gates bindings may still change, but for u-boot that does not matter
as we do not (yet) use any clock info from devicetree for sunxi u-boot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.
PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.
The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on existing A23/A33 code and the original H3 boot0.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Unify serial_tegra, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_rockchip, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Simon Glass <sjg@chromium.org>
Adjust the cros_ec keyboard driver to support driver model. Make this the
default for all Exynos boards so that those that use a keyboard will build
correctly with this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the tegra keyboard driver to support driver model, using the new
uclass. Make this the default for all Tegra boards so that those that use
a keyboard will build correctly with this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Put jump trampoline to TCM at 0 and setup R5 reset address to 0.
Jump trampoline ensures that jump to the right location.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently the mmc device that SPL looks at is always mmc0, regardless
of the BOOT_DEVICE_MMCx value. This forces some boards to
implement hacks in order to boot from other mmc devices.
Make SPL take into account the correct mmc device.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.
Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).
Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728
The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.
Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.
NOTE: Commit eae7ae1853 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.
As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Instead of allocating space in the driver for the serdes
specification table, just allow the board file to set a pointer
to it. Also, allow the board to only specify the lanes that are
used instead of including unused lanes.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Functions that do not modify the pointer passed should declare it
as const.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support. Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM. If this needs to be done, it should be
handled in the board file, not in core code.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Enable TI_EDMA3 and QUAD read support for ti_qspi on am43xx, this
increases read performance to 4 MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Fix below compilation warnings-
drivers/gpio/hi6220_gpio.c: In function ‘hi6220_gpio_probe’:
drivers/gpio/hi6220_gpio.c:82:15: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
bank->base = (u8 *)plat->base;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Compile misc.c for mx7, since we need related function for
lcdif and nand.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Need to call lcdif_power_down to make lcdif in initial state
before kernel boot. Similar issue for uboot reset with lcdif
enabled, system will hang after serveral times resetting. Need
to let lcdif initial state to make all go well.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
We need to power down lcdif before uboot reset to make reset can pass
stress test.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Introudce a new function lcdif_power_down.
1. Waits for a VSYNC interrupt to guarantee the reset is done at the
VSYNC edge, which somehow makes the LCDIF consume the display FIFO(?)
and helps the LCDIF work normally at the kernel stage.
2. Add power down function to stop lcdif.
The reason to introduce lcdif_power_down is that we want lcdif to be in
initial state when doing uboot reset or before kernel boot to make
system stable, otherwise system may hang.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Implement mxs_set_lcdclk, enable_lcdif_clock and enable_pll_video.
The three API can be used to configure lcdif related clock when
CONFIG_VIDEO_MXS enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
1. Move WDOG3_BASE_ADDR to '#if !(defined(__ASSEMBLY__))'.
2. Add i.MX6UL LCDIF register base address. And Introduce
LCDIF1_BASE_ADDR to support runtime check.
3. include <asm/imx-common/regs-lcdif.h> for imx-regs.h to avoid
building error for mxsfb.c, since mxsfb.c use imx-regs.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Share one lcdif structure for i.MXes.
1. Discard struct mxs_lcdif_regs from imx-regs.h of i.MX7
2. Add i.MX6SX/6UL/7D support in imx-lcdif.h of imx-common
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Move 'struct mxs_lcdif_regs' and lcdif related macro definitions to
arch/arm/include/asm/imx-common/regs-lcdif.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
There are uint8_t, uint32_t types in regs-common.h, so include
linux/types.h.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Change mxs_set_lcdclk prototype to add a new parameter
base_addr. There are two LCD interfaces for i.MX6SX,
we may support LCDIF1 or LCDIF2.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
1. add basic psci support for imx7 chip.
2. support cpu_on and cpu_off.
3. switch to non-secure mode when boot linux kernel.
4. set csu allow accessing all peripherial register in non-secure mode.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The code such as PSCI in section named secure is bundled with
u-boot image, and when bootm, the code will be copied to their
runtime address same to compliation/linking address -
CONFIG_ARMV7_SECURE_BASE.
When compile the PSCI code and link it into the u-boot image,
there will be relocation entries in .rel.dyn section for PSCI.
Actually, we do not needs these relocation entries.
If still keep the relocation entries in .rel.dyn section,
r0 at line 103 and 106 in arch/arm/lib/relocate.S may be an invalid
address which may not support read/write for one SoC.
102 /* relative fix: increase location by offset */
103 add r0, r0, r4
104 ldr r1, [r0]
105 add r1, r1, r4
106 str r1, [r0]
So discard them to avoid touching the relocation entry in
arch/arm/lib/relocate.S.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
p2371-2180 is the engineering board name for the Jetson TX1 developer
kit. Update Kconfig description and help text to make this obvious to
everyone.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rename GPU functions to less generic names to avoid potential name
collisions.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable the GPU node in the system-wide ft_system_setup() hook instead of
the board-specific ft_board_hook(). This allows us to enable GPU per SoC
generation instead of per-board as we did initially.
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There is no justification for this function, especially in exported
form.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add code to detect timeouts when waiting for HW events such as PLL
lock done. Any errors are logged and trigger an error return code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the tables defining which pads and mux options exist in the Tegra210
XUSB padctl hardware.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This change simply deletes code from the Tegra210 XUSB padctl driver that
is already present in the common XUSB padctl code. Since all the arrays
in tegra210_socdata are empty, this update may leave the Tegra210 XUSB
padctl driver non-functional at run-time. However, (a) this driver is not
used yet so no regression can be observed and (b) the next commit will
immediately fix this up.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
There are some differences between the Tegra124 and Tegra210 XUSB padctl
code. So far, the common XUSB padctl code only supports Tegra124. Add
some parameters etc. so that it can work for both chips.
This also allows moving Tegra124's process_nodes() into the common file;
something that would have requires edits during the move if done in the
previous commit.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A fair amount of the XUSB padctl driver will be common between Tegra124
and Tegra210. To avoid cut/paste between the two chips, create a new
file that will contain the common code, and convert the Tegra124 code to
use it. This change doesn't move every last piece of code that can/will be
shared, but rather concentrates on moving code that can be moved with zero
changes, so there are no other diffs mixed in.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This file defines pr_fmt(), so the individual error() calls don't need to
include the prefix in their format strings. Doing so results in duplicate
text in any error messages. Remove the duplication.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A future patch will soon move some of the XUSB padctl code into a common
file in arch/arm/mach-tegra. Rename the existing dummy XUSB padctl file
to avoid conflicting with that, or being confusing.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
p2371-2180 has two PCI ports; a regular x4 slot and a x1 M.2 slot. This
patch adds the relevant DT to enable the PCI controller and configure
the XUSB padctl pin muxing, and code to turn on the PCI power and enable
PCI features in U-Boot. I have only tested the x4 slot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra210's PCI controller is largely identical to Tegra124, and hence
shares the same binding. However, it has a unique compatible value due
to the existence of at least one new HW bug that would prevent any driver
for a previous HW version from operating correctly.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Implement the procedure that the TRM mandates to initialize PLLREFE and
PLLE. This makes the PLL actually lock.
Note that this section of the TRM is being cleaned up to remove some
confusion. The set of register accesses in this patch should be final,
although the step numbers/descriptions might still change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The latest Linux can directly handle SMP operations for UniPhier SoCs
without any help of U-boot. Drop the relevant code from U-boot.
See commit b1e4006aeda8c8784029de17d47987c21ea75f6d ("ARM: uniphier:
rework SMP operations to use trampoline code") in Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This makes USB3.0 available on new SoCs/boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The IRQ is not used in U-Boot, but this would be useful to sync
device trees between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This sets up a fine-grained page table, which is a requirement for
noncached_init() to operate correctly.
MMU setup code currently exists in a number of places:
- A version in the core ARMv8 support code that sets up page tables that
use very large block sizes that CONFIG_SYS_NONCACHED_MEMORY doesn't
support.
- Enhanced versions for fsl-lsch3 and zynmq that set up finer grained
page tables.
Ideally, rather than duplicating the MMU setup code yet again this patch
would instead consolidate all the different routines into the core ARMv8
code so that it supported all use-cases. However, this will require
significant effort since there appear to be a number of discrepancies[1]
between different versions of the code, and between the defines/values by
some copies of the MMU setup code use and the architectural MMU
documentation. Some reverse engineering will be required to determine the
intent of the current code.
[1] For example, in the core ARMv8 MMU setup code, three defines named
TCR_EL[123]_IPS_BITS exist, but only one of them sets the IPS field and
the others set a different field (T1SZ) in the page tables. As far as I
can tell so far, there should be no need to set different values per
exception level nor to modify the T1SZ field at all, since TTBR1 shouldn't
be enabled anyway. Another example is inconsistent values for *_VA_BITS
between the current core ARMv8 MMU setup code and the various SoC-
specific MMU setup code. Another example is that asm/armv8/mmu.h's value
for SECTION_SHIFT doesn't match asm/system.h's MMU_SECTION_SHIFT;
research is needed to determine which code relies on which of those
values and why, and whether fixing the incorrect value will cause any
regression.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
In order for noncached_init() to operate correctly, SoCs must set up a
custom page table with fine-grained (2MiB) sections, which can be
configured from noncached_init().
This is currently performed by arch/arm/cpu/armv8/{fsl-lsch3,zynqmp}/cpu.c
by cut/pasting and re-implementing mmu_setup, enable_caches(), etc. There
are some other reasons for the duplication there though, such as enabling
icache early, and enabling dcaching earlier with a different configuration.
This change makes mmu_setup() a weak implementation, so that the MMU setup
code can be replaced without having to duplicate other code that calls it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The implementation of noncached_init() uses define MMU_SECTION_SIZE.
Define this on ARM64.
Move the prototype of noncached_{init,alloc}() to a location that
doesn't depend on !defined(CONFIG_ARM64).
Note that noncached_init() calls mmu_set_region_dcache_behaviour() which
relies on something having set up translation tables with 2MB block size.
The core ARMv8 MMU setup code does not do this by default, but currently
relies on SoC specific MMU setup code. Be aware of this before enabling
this feature on your platform!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Old sector number is not being cleared from FLASH_CR register. For example
when first erased sector was 001 and then you want to erase sector 010,
sector 011 gets erased instead.
This patch clears old sector number from FLASH_CR register before a new
one is written.
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
flash_lock call is inside a for loop, so after the first iteration flash
is locked and no more sectors can be erased.
Move flash_lock out of the loop.
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Revert commit 7a2c1b13 which dropped OpenRD boards.
Assume maintainership of OpenRD.
Remove OpenRD from scrapyard.
Switch OpenRD to generic board.
Switch to Thumb build.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Kirkwood files cpu.c and cache.c cannot build in Thumb state;
force them in ARM state even under CONFIG_SYS_THUMB_BUILD.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
When building a Thumb-1-only target with CONFIG_SYS_THUMB_BUILD,
some files fail to build, most of the time because they include
mcr instructions, which only exist for Thumb-2.
This patch introduces a Kconfig option CONFIG_THUMB2 and uses
it to select between Thumb-2 and ARM mode for the aforementioned
files.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch fixes compile warnings like this:
warning: format '%lu' expects argument of type 'long unsigned int',
but argument 5 has type 'size_t'
In C99 standard you can use %zu modifier to print size_t values.
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
If you enable CONFIG_SEMIHOSTING for STM32F429 target, you will get compile
error looking like this:
arch/arm/lib/semihosting.c: In function 'smh_read':
{standard input}: Assembler messages:
{standard input}:34: Error: invalid swi expression
{standard input}:34: Error: value of 1193046 too large for field of 2 bytes at 0
scripts/Makefile.build:277: recipe for target 'arch/arm/lib/semihosting.o' failed
The source of the problem is "svc #0x123456" instruction. This instruction
can not be encoded using Thumb2 instruction set used by ARMv7M CPUs.
ARM documentation suggests using "bkpt #0xAB" instruction instead [1].
This patch fixes compile errors and adds support for semihosting for
STM32F429 or any other ARMv7M target.
This change was sested on STM32F429-DISCOVERY board using OpenOCD and
"smhload" u-boot command.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0471c/Bgbjhiea.html
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
This patch fix compilation error:
drivers/mmc/zynq_sdhci.c:16:5: error: conflicting types for
‘zynq_sdhci_init’
int zynq_sdhci_init(phys_addr_t regbase)
^
In file included from drivers/mmc/zynq_sdhci.c:14:0:
./arch/arm/include/asm/arch/sys_proto.h:16:5: note: previous declaration
of ‘zynq_sdhci_init’ was here
int zynq_sdhci_init(unsigned long regbase);
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the is_power_of_2() definition from log2.h to align with the
kernel implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
With a working QSPI calibration, the SCLK can now run up to 100MHz
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vikas Manocha <vikas.manocha@st.com>
Cc: Jagannadh Teki <jteki@openedev.com>
Cc: Pavel Machek <pavel@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Remove zc70x target which was one setting for zc702 and zc706.
Currently zc702 and zc706 are separated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Update this driver to use driver model and change all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPI requires DM and OF that's why enable DM for ZynqMP
and start to use configuration based on embedded OF.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to mark some device tree nodes so that they are available before
relocation. This enables driver model to find these automatically. In the
case of SPL it ensures that these nodes will be retained in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move to using device tree control in SPL so that we can use the same driver
code in both SPL and U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the debug UART to assist with early debugging. Enable it
for Zybo as an example.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move to the new way of starting up SPL. Clearing of BSS and calling
board_init_r() is now handled by crt0.S.
Also tidy up the header include order.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The DMA, QSPI, and SD/MMC reset bits are located in the permodrst register,
not the mpumodrst. So the bank for these reset bits should be 1, not 0.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The SDHCI is introduced by sama5d2, named as Secure Digital Multimedia
Card Controller(SDMMC). It supports the embedded MultiMedia Card (e.MMC)
Specification V4.41, the SD Memory Card Specification V3.0, and the SDIO
V3.0 specification. It is compliant with the SD Host Controller Standard
V3.0 specification.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Some peripherals may need a second clock source that may be different
from the system clock. This second clock is the generated clock (GCK)
and is managed by the PMC via PMC_PCR.
For simplicity, the clock source of the GCK is fixed to PLLA_CLK.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Provide the specific addresses for the Chip ID and Chip ID Extension
registers, instead of the offset, which make it use on other chips.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch will fix these checkpatch issues.
ERROR: Macros with complex values should be enclosed in parentheses
+#define DEFAULT_DQS_X4 (DEFAULT_DQS << 24) || (DEFAULT_DQS << 16) \
+ || (DEFAULT_DQS << 8) || (DEFAULT_DQS << 0)
ERROR: space prohibited before that ',' (ctx:WxW)
+ writel(val , &drex0->concontrol);
^
ERROR: space prohibited before that ',' (ctx:WxW)
+ writel(val , &drex1->concontrol);
^
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
There are 8 pins for SD card in Exynos, but the MUX was configured
only for 7, since the one was used for card detection.
This caused the pin's pull wrong configuration.
This commit fixes this and the card detect can work properly,
after call this function.
Tested-on: Odroid U3 and Odroid X2.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This ADC is required for Odroid's board revision detection.
The pre-reloc request is enabled, since board detection will
be done in one of early function call.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit adds common ADC node, which is disabled as default.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit adds driver for Exynos54xx ADC subsystem.
The driver is implemented using driver model, amd provides
ADC uclass's methods for ADC single channel operations:
- adc_start_channel()
- adc_channel_data()
- adc_stop()
The basic parameters of ADC conversion, are:
- sample rate: 600KSPS
- output the data as average of 8 time conversion
ADC features:
- sample rate: 600KSPS
- resolution: 12-bit
- channels: 10 (analog multiplexer)
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The proper CPU ID for those Exynos variants is 0x5422,
but before the 0x5800 was set. This commit fix this back.
Changes:
- set cpu id to 0x5422 instead of 0x5800
- remove macro proid_is_exynos5800()
- add macro proid_is_exynos5422()
- change the calls to proid_is_exynos5800() with new macro
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This platform is based on Exynos5800 but the cpu id is 0x5422.
This doesn't fit the common Exynos SoC name convention, so now,
the CPU name is defined by device tree string, to be printed
properly.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The CPU name for Exynos was concatenated with cpu id,
but for new Exynos platforms, like Chromebook Peach Pi
based on Exynos5800, the name of SoC variant does not
include the real SoC cpu id (0x5422).
For such case, the CPU name should be defined in device tree.
This commit introduces new device-tree property for Exynos:
- "cpu-model" - with cpu name string
If defined, then the cpu id is not printed.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
crt0.S do both memset the bss section and call board_init_r for us, so
remove them from board_init_f().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>