Set BM poll size once during priv probe and do not
overwrite it during port probe procedure. Pool is common for
all CP ports.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
TX drain in transmit procedure could cause issues due
to race between drain procedure and transmition of descriptor
between AGGR TXQ and physical TXQ.
TXQ will be cleared before moving to Linux by stop procedure.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
MVPP22 driver support 64 Bit arch and require BM pool
high address configuration.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove IRQ configuration from U-Boot PP driver.
U-Boot don't use interrupts and configuration of IRQ in U-Boot
caused crashes in Linux shared interrupt mode.
Also interrupt use is redundant in RX routine since a single RX
queue is used.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
MBUS driver were replaced by AXI in PPv22 and relevant
only for PPv21.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
U-boot use single physical tx queue with size 16 descriptors.
So aggregated tx queue size should be equal to physical tx queue
and cpu descriptor chunk(number of descriptors delivered from
physical tx queue to aggregated tx queue by one chunk) shouldn't be
larger than physical tx queue.
Fix:
Set AGGR_TXQ and CPU_DESC_CHUNK to be 16 descriptors, same as
physical TXQ.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Issue:
BM counters were overrun by probe that called per Network interface and
caused release of wrong number of buffers during remove procedure.
Fix:
Use probe_done and num_ports to call init and remove procedure
once per communication controller.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables padding of packets shorter than 64B in TX(set by default).
Disabling of padding causes crashes on MACCIATO board.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
A8K marvell SoC has two South Bridge communication controllers(CP0 and CP1).
Each communication controller has packet processor ports and MDIO.
On MACHIATOBin board ports from CP1 are connected to mdio on CP0.
Issue:
Wrong base address is assigned to MDIO interface during probe.
Fix:
Get MDIO address from PHY handler parent base address.
This should be refined in the future when MDIO driver is implemented.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch add GPIO configuration support in mvpp2x driver.
Driver will handle 10G SFP gpio reset and SFP TX disable. GPIO pins should
be set in device tree.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This defconfig uses the PCIe x4 binary blobs from the congatec BIOS.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Disable debug UART
- Enable more partition support
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds the common header include file theadorable-x86-common.h
for the theadorable-x86 targets to define all common options and the
default environment.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds the infrastructure to define different config headers
with different configurations and default environment for the baseboards
that can now be selected via Kconfig. The new configuration for the
theadorable-x86-conga-qa3-e3845 is also added. Also the new defconfig
file for this new target is added.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds the infrastructure to define different config headers
with different configurations and default environment for the baseboards
that can now be selected via Kconfig. The new configuration for the
theadorable-x86-dfi-bt700 is also added.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When CONFIG_EFI_PARTITION is not set, the following build error is
seen in arch/x86/lib/acpi_s3.c:
error: expected declaration specifiers or '...' before '*' token
static void asmlinkage (*acpi_do_wakeup)(void *vector) = (void*)WAKEUP_BASE;
This is actually caused by missing asmlinkage declaration, but with
CONFIG_EFI_PARTITION on, the declaration comes from part.h which
is included from common.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is defined twice in the same file, with the same value, likely
because of some patch merge issue. Pick the uglier one and nuke it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The I2C reading in the PEX vs SATA detection code often fails on the
first try. Try three times, as the code for EEPROM reading does.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Neither new design uses ISA bus, nor does any U-Boot codes use these
codes. Remove them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The environment variable "disable_giga" can now be used to disable
1000baseTx on the Micrel's KSZ9031.
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Added the AFE (Analog Front End) settings for stability to the
Broadcom Cygnus phy. This improves the time take to perform
auto negotiation.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
move to Kconfig:
CONFIG_BCM_SF2_ETH
CONFIG_BCM_SF2_ETH_DEFAULT_PORT
CONFIG_BCM_SF2_ETH_GMAC
Also modified defconfigs of all platforms that use these configs.
Signed-off-by: Suji Velupillai <suji.velupillai@broadcom.com>
Tested-by: Suji Velupillai <suji.velupillai@broadcom.com>
Reviewed-by: JD Zheng <jiandong.zheng@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The correct option is PHY_MICREL_KSZ90X1, but some configs still
select the 9021 and 9031 options, which are deprecated.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There should be no longer be any ksz9000 users that pick up the PHY
driver from ksz8xxx, so remove ksz9000 remnants from there.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These boards will now use the ksz90x1 driver instead of the mess in
ksz8xxx. This change is needed before the two drivers can be fully
separated.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.
As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.
To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For strncpy() select a minimal string length of destination and source
strings, here DEFAULT_NAME_LEN is preferable to MAX_LEN.
Due to the NUL-terminated contents of default_string the change is
a noop, however it removes a compilation warning if SH2/3/4 platform
specific strncpy() function is used:
In file included from include/linux/string.h:21:0,
from include/common.h:28,
from net/tftp.c:9:
net/tftp.c: In function 'tftp_start':
arch/sh/include/asm/string.h:52:42: warning: array subscript is above array bounds [-Warray-bounds]
: "0" (__dest), "1" (__src), "r" (__src+__n)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The register constants don't use the exact names that are used in the
TRM, so add comments that use the exact names so that it is clear what
register is being referred to.
https://www.atheros-drivers.com/qualcomm-atheros-datasheets-for-AR9331.html
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Marek Vasut <marex@denx.de>
After upgrading to GCC 7.1, the duplicate const specifies in the
r8152 driver trigger the following build warnings with buildman
(observed on a 'buildman rockchip' test)::
../drivers/usb/eth/r8152.c:62:35: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
static const struct r8152_version const r8152_versions[] = {
^~~~~
This commit fixes these by removing the duplicate 'const' specifier
from the declarations.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This is only used in cmd/net.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Previously seeded by obtaining mac addr from env. If mac addr was
never set, rand would output 0. This fix obtains the mac addr
from driver instead.
Signed-off-by: Jimmy Du <jimmy.du@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
phy_device_create(..) sets the addr of phy_device with a sane value.
There is no need overwrite it.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for rk3288 mipi dsi.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add rk3288 soc specific driver for mipi dsi.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add Makefile item for soc specific driver for rk3399 mipi dsi.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To compatible with different rockchip soc, we split the mipi dirver into
common and soc specific parts, and all the soc share the common
functions from common driver part.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[agust: fix build breakage and warnings]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The mipi panel used on evb-rk3399 has a 1920x1200 resolution. But now
the max resolution is 1920x1080. So increase it.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>