These additional nodes need to be provided to get U-Boot to boot correctly
on the Canyonlands / Glacier board:
- chosen path to the console-uart
- reg-shift set to 0 in the uart device nodes
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Define an _end symbol indicating the end of u-boot.bin. Also add some dummy
words into the link script to ensure that u-boot.bin will always extend
that far. There may be a better way of doing this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is required at present for device tree control. The ppc4xx does support
GPIOs but does not seem to have a proper driver. So this file is empty.
Signed-off-by: Simon Glass <sjg@chromium.org>
The canyonlands.h config file works with canyonlands, glacier and arches
boards. Bring in the device tree files for these from Linux 3.17.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new ramboot config for glacier so that it is possible to test U-Boot
loaded over Ethernet instead of using JTAG.
Signed-off-by: Simon Glass <sjg@chromium.org>
Many CONFIG options have an unnecessary value of 1. CONFIG_440 is set in
the various board config files. Also simplify the CONFIG_440 check in
config.mk
Signed-off-by: Simon Glass <sjg@chromium.org>
When booting in JTAG mode, there is no way to use soft break-points, and
no way of knowing when SPL has finished executing (so the user can issue
a 'halt' command to load u-boot.bin for example)
Add a debug output and simple loop to stop execution at the completion of
the SPL initialisation as a pseudo break-point when booting in JTAG mode
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Section 4.1.2 of Freescale Application Note AN4199 describes the
configuration required to operate the mx28 from a 5V source without a
battery.
This patch changes the behaviour of the dropout control of the DC-DC
converter (refer to section 11.12.9 of the mx28 Application Processor
Reference Manual - Document Number: MCIMX28RM, Rev 2, 08/2013) to the
following:
- Always use 4P2 Linear Regulator if CONFIG_SYS_MXS_VDD5V_ONLY is defined
- Switch between 4P2 Linear Regulator and Battery, using whichever has
the highest voltage if CONFIG_SYS_MXS_VDD5V_ONLY isnot set (this is
the same as the pre-patch behaviour)
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Signed-off-by: Damien Gotfroi <dgotfroi@greenwatch.be>
It is difficult to track down fail to boot issues in the mxs SPL.
Implement the following to make it easier:
- Add debug outputs to allow tracing of SPL progress in order to track
where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must
be defined to enable debug output in SPL
- Add TODO comments where it is not clear if the code is doing what it
is meant to be doing, even tough the board boots properly (these comments
refer to existing code, not to any code added by this patch)
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Should use AIPS3 configuration address 0x0227C000 to set AIPS3,
not the AIPS3 base address.
Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with
AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem.
Signed-off-by: Ye.Li <B37916@freescale.com>
This patch has some parts connected together:
- Use _gd in bss section which is automatically cleared
Location at SPL_MALLOC_END wasn't cleared at all
- Use MALLOC_F_LEN(early alloc) instead of FULL MALLOC
(mem_malloc_init is not called at all)
- Simplify malloc and stack init.
At the end of SPL addr is malloc area and below is stack
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Because it is not compatible with DM where
malloc_base has to be available early and init
has to be done in ASM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Compile code with -fPIC to get GOT. Do not build SPL
with fPIC because it increasing SPL size for nothing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Setup gd from ASM to be availalbe for board_init_r.
Setting it up in spl_board_init is too late when
MALLOC is used.
Space for gd is located behind MALLOC area at the end of BRAM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not use specific macros for debugging.
Also remove compilation warning:
w+../arch/microblaze/cpu/interrupts.c: In function 'interrupt_handler':
w+../arch/microblaze/cpu/interrupts.c:153:2: warning: format '%x'
expects argument of type 'unsigned int', but argument 2 has type 'void
(*)(void *)' [-Wformat]
w+../arch/microblaze/cpu/interrupts.c:153:2: warning: format '%x'
expects argument of type 'unsigned int', but argument 4 has type 'void
*' [-Wformat]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not save registers below r1 stack pointer because
it is not checked by stack undeflow is not able to detect
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This way we may have very limited set of functions implemented so we
save some space.
Also it allows us to build U-Boot for any ARC core with the same one
toolchain because we don't rely on pre-built libgcc.
For example:
* we may use little-endian toolchain but build U-Boot for ether
endianess
* we may use non-multilibbed uClibc toolchain but build U-Boot for
whatever ARC CPU flavour that current GCC supports
Private libgcc built from generic C implementation contributes only 144
bytes to .text section so we don't see significant degradation of size:
--->8---
$ arc-linux-size u-boot.libgcc-prebuilt
text data bss dec hex filename
222217 24912 214820 461949 70c7d u-boot.libgcc-prebuilt
$ arc-linux-size u-boot.libgcc-private
text data bss dec hex filename
222361 24912 214820 462093 70d0d u-boot.libgcc-private
--->8---
Also I don't notice visible performance degradation compared to
pre-built libgcc (where at least "*div*" functions are had-written in
assembly) on typical operations of downloading 10Mb uImage over TFTP and
bootm.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As a preparation to ARCv2 port submission we're moving CPU slection
flags to a common location.
Also it will allow us to have more flexible CPU specification, not only
ISA version but CPU family as well checking CONFIG_ARC_CPU_xxx.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Common arch_early_init_r() is used in "arc/lib/cpu.c" for all ARC boards
so there's no sense in separate per-board definitions.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
There're no other options for ARC except "generic board" so ther's no
point to define CONFIG_SYS_GENERIC_BOARD per board.
We now have it set fo all ARC boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This change allows to keep board description clean and minimalistic.
This is especially helpful if one board may house different CPUs with
different features.
It is applicable to both FPGA-based boards or those that have CPUs
mounted on interchnagable daughter-boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This change allows to keep board description clean and minimalistic.
This is especially helpful if one board may house different CPUs with
different features.
It is applicable to both FPGA-based boards or those that have CPUs
mounted on interchnagable daughter-boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Now we may select a particular version of ARC700:
* ARC750D or
* ARC770D
It allows more flexible (or more fine tuned) configuration of U-Boot.
Before that change we relied on minimal configuration but now we may
use specific features of each CPU.
Moreover allows us to escape manual selection of options that
exist in both CPUs but may have say different version like MMUv2 in
ARC750D vs MMUv3 in ARC770D.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
It's prohibited to put branch instruction in the very end of zero-delay
loop. On execution this causes "Illegal instruction" exception.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
As the at91cap9adk board is removed by commit: b5508344
(ARM: remove broken "at91cap9adk" board), so the at91cap9
code is not used anymore, and also the document for
at91cap9 can not be found on www.atmel.com, so remove the
at91cap9 related code.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Some SoC need to redirect the saic to aic to make the interrupt to
work, here add a weak function to be replaced by real function.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
The SFR (special function registers) can be shared bwteen
sama5d3 and sama5d4 soc.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[whitespace adoptions for 80 char compliance]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This matrix header file can be shared between sama5d3 and sama5d4 soc.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[whitespace adaptions for 80 char compliance]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Space is used before 'default' in PCIE_ECAM_BASE in arch/x86/Kconfig
so it looks misaligned. Replace the space with tab to indent.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Galileo board has a microSD slot which is routed from Quark SoC
SDIO controller. Enable SD/MMC support so that we can use an SD card.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Quark SoC contains a legacy SPI controller in the legacy bridge
which is ICH7 compatible. Like Tunnel Creek and BayTrail, the BIOS
control register offset in the ICH SPI driver is wrong for the Quark
SoC too, unprotect_spi_flash() is added to enable the flash write.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC has a legacy GPIO block in the legacy bridge (D0:F31),
which is just the same one found in other x86 chipset. Since we
programmed the GPIO register block base address, we should be
able to enable the GPIO support on Intel Galileo board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC has some non-standard BARs (excluding PCI standard BARs)
which need be initialized with suggested values. This includes GPIO,
WDT, RCBA, PCIe ECAM and some ACPI register block base addresses.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we have added Quark MRC codes, call MRC in dram_init() so
that DRAM can be initialized on a Quark based board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
For some unknown reason, the TSC calibration via PIT does not work on
Quark. Enable bypassing TSC calibration and override TSC_FREQ_IN_MHZ
to 400 per Quark datasheet in the Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should allow the value of TSC_FREQ_IN_MHZ to be overridden by
the one in arch/cpu/<xxx>/Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make the Intel quark/galileo support avaiable in Kconfig and Makefile.
With this patch, we can generate u-boot.rom for Intel galileo board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
New board/intel/galileo board directory with minimum codes, plus
board dts, defconfig and configuration files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add minimum codes to support Intel Quark SoC. DRAM initialization
is not ready yet so a hardcoded gd->ram_size is assigned.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quark SoC contains an embedded 512KiB SRAM (eSRAM) that is
initialized by hardware. eSRAM is the ideal place to be used
for Cache-As-RAM (CAR) before system memory is available.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move PCI_REG_ADDR and PCI_REG_DATA from arch/x86/lib/pci_type1.c to
arch/x86/include/asm/pci.h, also define PCI_CFG_EN so that these
macros can be used for pci configuration space access.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In the Quark SoC, some chipset commands are accomplished by utilizing
the internal message network within the host bridge (D0:F0). Accesses
to this network are accomplished by populating the message control
register (MCR), Message Control Register eXtension (MCRX) and the
message data register (MDR).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
device.h for integrated pci devices' bdf on Quark SoC and quark.h for
various memory-mapped and i/o-mapped base addresses within SoC.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is a relatively low-cost x86 board in a small form factor. The main
peripherals are uSD, USB, HDMI, Ethernet and SATA. It uses an Atom 3800
series CPU. So far only the dual core 2GB variant is supported.
This uses the existing FSP support. Binary blobs are required to make this
board work. The microcode update is included as a patch (all 3000 lines of
it).
Change-Id: I0088c47fe87cf08ae635b343d32c332269062156
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since the FSP is a black box it helps to have some sort of debugging
available to check its inputs. If the debug UART is in use, set it up
after CAR is available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
While queensbay is the first chip with these settings, others will want to
use them too. Make them common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since these board functions seem to be the same for all boards which use
FSP, move them into a common file. We can adjust this later if future FSPs
need more flexibility.
This creates a generic PCI MMC device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This code is ported from the Marvell bin_hdr code into mainline
SPL U-Boot. It needs to be executed very early so that the devices
connected to the serdes PHY are configured correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
This patch adds SPL support to the Marvell Armada-XP. With this addition
the bin_hdr integration is not needed any more. The SPL will first
initialize the serdes/PHY and the call the DDR setup and training code
now integrated into mainline U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
This patch adds SPL support to the db-mv784mp-gp eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
This patch adds SPL support to the maxbcm MV78460 based board. Including
the fixed DDR configuratrion needed for the DDR training code. And the
the serdes PHY init code.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
Checking if the pointer is NULL would be easier to know the tail
of the boot_device_table[] array.
For clarification, add the /* sentinel */ comment.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The return value of get_boot_mode_sel() is used as the index of
the boot_device_table[] array. Its type should be "int" rather
than "u32".
Use only the iterator "i" for the loop in do_pinmon().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
To use I2C controllers on PH1-sLD8, the bit 10 (SCL0/SDA0)
and bit 11 (SCL1/SDA1) of IECTRL register must be set.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
It is true that unused functions are removed from the ELF image
by the compiler's garbage collection but relying on it too much
does not look nice.
Currently, the build is taking more than it should.
Refactor the makefiles to compile only files that are really needed.
CONFIG_SOC_INIT and CONFIG_DRAM_INIT are no longer needed by the
optimization.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since commit 0365ffcc0b (generic-board: show model name in
board_init_f() too), checkboard() is invoked only when
show_board_info() fails to get the model name from Device Tree.
It never happens because UniPhier SoCs now only work with
CONFIG_OF_CONTROL and all the root nodes of UniPhier device trees
have the "model" property.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since commit 0365ffcc0b (generic-board: show model name in
board_init_f() too), the support card information has not been
displayed because check_support_card() is invoked only when
show_board_info() fails to get the model name from Device Tree.
This commit adds misc_init_f() function to call check_support_card()
from there.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now init functions called from board_postclk_init() and dram_init()
are only necessary for SPL.
Move them to spl_board_init() for clean-up.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Currently, I/O pin settings are not necessary for SPL.
The board_early_init_f() seems a suitable place to call pin_init().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The EEPROM chips on UniPhier reference daughter boards expect 2-byte
offset address.
Since 7132b9fd68 (dm: i2c: dts: Support an offset-len device tree
property), I2C sub-nodes can have "u-boot,i2c-offset-len" property.
It is convenient to set the default I2C offset address length in
Device Tree, so that we do not have to set it on the command line.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This EEPROM chip is installed on the expansion board commonly used
on UniPhier platform. To avoid duplicated description, move the
EEPROM node to a separate file and include it from other device tree
sources.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This dummy header was introduced by commit 630bf80ebb (ARM:
UniPhier: add dummy gpio.h to enable CONFIG_OF_CONTROL).
Thanks to commit a08d643dbd (dm: Drop gpio.h header from
fdtdec.c), such an ugly workaround is no longer needed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
For now this code seems to be the same for all FSP platforms. Make it
common until we see what differences are required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
To avoid casts, find_fsp_header() should return a pointer. Add asmlinkage
to two API functions which use that convention. UPD_TERMINATOR is common
so move it into a common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
If the BIOS emulator is not available, allow use of native execution if
available, and vice versa. This can be controlled by the caller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This setting will be used by more than just ivybridge so make it common.
Also rename it to PCIE_ECAM_BASE which is a more descriptive name.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
And use this to set the GMAC Transmit Clock Delay Chain value on Banana
boards, rather then keying of CONFIG_TARGET_FOO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
It is painful to specify the full path to the device tree with the -d
option. It is normally kept in the same directory as U-Boot, so provide
an option to use this by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Juno Development Platform is a physical Versatile Express
device with some differences from the emulated semihosting
models. The main difference is that the system is split in
a SoC and an FPGA where the SoC hosts the serial ports at
totally different adresses.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Versatile Express ARMv8 semihosted FVP platform is still
using the legacy CONFIG_SYS_EXTRA_OPTIONS method to configure
some compile-time flags. Get rid of this and create a Kconfig
entry for the FVP model, and a selectable bool for the
semihosting library.
The FVP subboard is now modeled as a target choice so we can
eventually choose between different ARMv8 versatile express
boards (FVP, base model, Juno...) this way. All dependent
symbols are updated to reflect this.
The 64bit Versatile Express board symbols are renamed
VEXPRESS64 so we have some chance to see what is actually
going on. Tested on the FVP fast model.
Acked-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unify and move code in arch/mips/cpu/mips[32|64]/ to arch/mips/cpu/.
The CPU specific config.mk files need to remain until
CONFIG_STANDALONE_LOAD_ADDR is converted to a global Kconfig symbol.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Move all au1x00 code out of arch/mips/cpu/mips32 to allow
unification of CPU code in a later patch. The reorganization
of the SoC specific header files will be done in a later patch
series.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
In preparation for sharing a single copy of start.S between mips32 &
mips64, handle setting the KX bit of the cop0 Status register when the
mips32 start.S is built for mips64.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
In preparation for sharing a single copy of start.S between mips32 &
mips64, handle mips64 relocations in the mips32 start.S when built for
mips64.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Where the mips32 & mips64 implementations of start.S differ in terms of
access sizes & offsets, use the appropriate macros from asm.h to
abstract those differences away. This is in preparation for sharing a
single copy of start.S between mips32 & mips64.
The exception to this is loads of immediates to be written to the cop0
Config register, which is a 32bit register on mips64 and therefore
constants written to it can be loaded as such.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This change fixes i2c bus numbering for Odroid U3.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Some versions of Exynos5 supports High-Speed I2C,
on few interfaces, this change allows support this.
The new flag is: PINMUX_FLAG_HS_MODE
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Without this alias setting, the seq numbers
of the i2c devices are wrong.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
This patch modify i2c nodes in exynos4.dtsi with:
- adding proper interrupts arrays for each i2c node,
which allows to decode periph id
- add reg address for each i2c node for i2c driver internal use
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
this is an atempt to make the export of functions typesafe.
I replaced the jumptable void ** by a struct (jt_funcs) with function pointers.
The EXPORT_FUNC macro now has 3 fixed parameters and one
variadic parameter
The first is the name of the exported function,
the rest of the parameters are used to format a functionpointer
in the jumptable,
the EXPORT_FUNC macros are expanded three times,
1. to declare the members of the struct
2. to initialize the structmember pointers
3. to call the functions in stubs.c
Signed-off-by: Martin Dorwig <dorwig@tetronik.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(resending to the list since my tweaks are not quite trivial)
Rather than assuming that the chip offset length is 1, allow it to be
provided. This allows chips that don't use the default offset length to
be used (at present they are only supported by the command line 'i2c'
command which sets the offset length explicitly).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
U-Boot now supports using GPIOs using bank phandles instead of global
numbers. Update the exynos device tree files to use this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Add a new 'demo light' command which uses GPIOs to control imaginary lights.
Each light is assigned a bit number in the overall value. This provides an
example driver for using the new GPIO API.
Signed-off-by: Simon Glass <sjg@chromium.org>
In f0c3a6c we stopped setting gd in board_init_f, but later had to
revert to due problems on certain platforms. As davinci does not look
to have these problems, we can drop the setting here and rely upon
crt0.S to do it.
Cc: Peter Howard <pjh@northern-ridge.com.au>
Signed-off-by: Tom Rini <trini@ti.com>
