Increase IO drive strength to fix FCS error on RGMII ports
on T1024QDS.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER.
but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs.
on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
10GEC1->MAC1, 10GEC2->MAC2
so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on
which 10GEC enumeration is consistent with MAC enumeration.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Freescale T1024/T1023 SoC.
The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
- Three PCI Express 2.0 controllers
- Additional peripheral interfaces
- One SATA 2.0 controller
- Two USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/eSDHC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T1024 and T1023:
Feature T1024 T1023
QUICC Engine: yes no
DIU: yes no
Deep Sleep: yes no
I2C controller: 4 3
DDR: 64-bit 32-bit
IFC: 32-bit 28-bit
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.
A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 v1.0 has this errata while v1.1 has fixed
this errata by hardware, add a new function has_errata_a007186
to check the SVR_SOC_VER, SVR_MAJ and SVR_MIN first,
if the sil has errata a007186, then run the errata code,
if not, doesn't run the code.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Workaround of Errata A-008044 was implemented without errata number and it is
enabled by default. Errata A-008044 is only valid for T1040 Rev 1.0.
So put errata number and make it conditional.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.
Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 rev 1.1 changes MEM_RAT in RCW, which requires new parsing for ratio,
the same way as T4240 rev 2.0.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Re-map NAND&I2C boot-device to the "normal" NAND boot-device.
Otherwise the SPL boot IF can't handle this device correctly.
Somehow booting with Hynix 4GBit NAND H27U4G8 on Siemens
Draco leads to this boot-device passed to SPL from the BootROM.
With this change, Draco boots just fine into main U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
The infomation of module control register for R-Car ARM SoC (r8a7790, r8a7791,
r8a7793 and r8a7794) are almost the same, they can be combined into one
structure. This provides structure that summarizes infomation of module control
register and default register values.
And this structure is the module control use of the kernel at boot time.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds infomation of bits for module control register. This is used
to control modules on ARM R-Car SoCs.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This addes macro for set and clear bit control for module control register.
This is used when user want to disable the function of the devices
corresponding to register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Control macro of mstp is common in R-Car ARM SoC (r8a7790, r8a7791,
r8a7793 and r8a7794). This moves these to arch-rmobile/rcar-mstp.h
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Module control registers of R-Car ARM SoC (r8a7790, r8a7791, r8a7793 and
r8a7794) are same address. This moves these to header file of SoC.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
BeagleBoard-X15 is the next generation Open Source
Hardware BeagleBoard based on TI's AM5728 SoC
featuring dual core 1.5GHZ A15 processor. The
platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60),
separate LCD port, video In port, 4GB eMMC, uSD,
Analog audio in/out, dual 1G Ethernet.
For more information, refer to:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
expose those two definitions so they can be
used by another board which we're adding in upcoming
patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
this will allow for boards to overwrite those
in case memory setup is different.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
If we want to have two sections, one on each EMIF, without
interleaving, current code wouldn't enable emif2. Fix that
problem.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
some boards might want to use USB1 for host,
without fiddling those registers it'll be
impossible.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Those regulators don't have any coupling with
what they supply, so remove the suffixes in order
to not confuse anybody.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
As checkpatch complaines about these camel-case defines, lets change
them to only use upper-case characters.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
- fix crash when sata device is not initialized
- remove disable_sata_clock() since it is not clear which clock for which
device should be disabled here
- call disable_sata_clock() for mx6 in preboot_os instead
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
If CONFIG_OF_CONTROL is defined, search device tree nodes that are
compatible with "panasonic,uniphier-ehci" and take the base address
from their "reg" property.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
This commit implements the ofdata_to_platdata handler for the UniPhier
serial driver and adds serial device nodes to the device tree sources.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. Consequently, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they do not
support GPIO.
In the first place, GPIO has nothing to do with OF_CONTROL.
It is wrong that lib/fdtdec.c includes GPIO functions; it should
be split into two files, FDT-common things and GPIO things.
It is, however, a pretty big work to fix that correctly.
This is a compromised commit to add a dummy <asm/arch/gpio.h>
to support OF_CONTROL for UniPhier platform. This dummy header
will be removed after FDT-GPIO stuff is fixed correctly.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The initramfs is currently only relocated if the user calls
the bootm ramdisk subcommand. If bootm should be used without
subcommands, the arch-specific bootm code needs to implement
the relocation.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
After all MIPS boards are switched to generic-board, the
MIPS specific board.c can be removed.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
To get correct stack walking and backtrace functionality in gdb,
registers fp and ra should be initialized before calling board_init_f
or board_init_r. Thus allocating stack space and zeroing it as it is
currently done in board.c becomes obsolete.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Merge struct s3c2410_nand and struct s3c2440_nand into one unified
struct s3c24x0_nand. While at it, fix up and rename the functions
to retrieve the NAND base address and fix up the s3c NAND driver to
reflect this change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
This fixes the following two problems:
cppcheck reports:
[arch/sandbox/cpu/start.c:132]: (error) Uninitialized variable: err
[arch/sandbox/cpu/os.c:371]: (error) Memory leak: fname
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Wolfgang Denk <wd@denx.de>
Intel's Graphics Media Accelerator (GMA) is a generic name for a wide range
of video devices. Add code to set up the hardware on ivybridge. Part of the
init happens in native code, part of it happens in a 16-bit option ROM for
those nostalgic for the 1970s.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 machines we can use an emulator to run option ROMS as with other
architectures. But with some additional effort (mostly due to the 16-bit
nature of option ROMs) we can run them natively. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Option ROMs require a few additional descriptors. Add these, and remove the
enum since we now have to access several descriptors from assembler.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add code to set up the Local Advanced Peripheral Interrupt Controller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rename interrupt_init() in arch/x86/lib/pcat_interrupts.c to
i8259_init() and create a new interrupt_init() in
arch/x86/cpu/interrupt.c to call i8259_init() followed by a
call to cpu_init_interrupts().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Since cpu_init_interrupts() was moved out of cpu_init_r(), it is
useless to keep cpu_init_r() for x86, thus remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Currently cpu_init_interrupts() is called from cpu_init_r() to
setup the interrupt and exception of the cpu core, but at that
time the i8259 has not been initialized to mask all the irqs
and remap the master i8259 interrupt vector base, so the whole
system is at risk of being interrupted, and if interrupted,
wrong interrupt/exception message is shown.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Intel chips have a turbo mode where they can run faster for a short period
until they reach thermal limits. Add code to adjust and query this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
These peripherals should not be at the top level, since they exist inside
the PCI bus. We don't have a full device tree node for pci yet, but we
should at least put it at the right level.
Signed-off-by: Simon Glass <sjg@chromium.org>
Set up all the remaining pieces of the LPC (low-pin-count) peripheral in
PCH (Peripheral Controller Hub).
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards will want to do some setup before and after a PCI hose
is scanned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Define the reset base in config.mk so that it does not need to be calculated
twice in the link script. Also tidy up the START_16 and RESET_VEC_LOC values
to fit with this new approach.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some toolchains put the relocation data into separate sections. Adjust the
linker script to catch this case. Without relocation data, U-Boot will not
boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This normally indicates a problem which will prevent relocation from
functioning, resulting in a hang. Panic in this case to make it easier
to debug.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is not needed. Remove it to improve the generic init sequence
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is now required to add subdirectories in the x86 cpu Makefile. Add this
to fix a build breakage for chromebook_link.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allwinner tells us that this bit of code is the rtc ram being used to detect
coming out of "super-standby" mode, and if that is the case, going out of
self-refresh mode.
Since we do not support "super-standby" mode, this can be dropped.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add simplefb support, note this depends on the kernel having support for
the clocks property which has recently been added to the simplefb devicetree
binding.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as
disussed on the devicetree list]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>.
This adds a fixed mode hdmi driver for the sunxi platform. The fixed
mode is a relatively safe 1024x768, more complete EDID handling is
currently not provided. Only HDMI is supported today.
This code is enabled when HPD detects an attached monitor.
Current config is such that 8MB is shaved off at the top of the RAM.
This avoids several memory handling issues, most significant is the fact
that on linux on ARM you are not allowed to remap known RAM as IO. A
clued in display driver will be able to recycle this reserved RAM in
future though.
cfbconsole was chosen as it provides the most important functionality: a
working u-boot console, allowing for the debugging of certain issues
without the need for a UART.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Major cleanups and some small bugfixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is a preparation patch for adding support for HDMI out.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The data sheet just calls it DRAM_CLK_REG, and on sun6i we've both a
dram_clk_cfg and dram_clk_gate, and the sun4i reg matches dram_clk_gate on
sun6i, so name it the same on sun4i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
SCFG_SCFGREVCR is SCFG bit reverse register. This register
must be written with 0xFFFFFFFF before writing to any other
SCFG register. Then other SCFG register could be written in
big-endian mode.
Address: 157_0000h base + 200h offset = 157_0200h
Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
W/R SCFGREV
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0-31
SCFGREV SCFG Bit Reverse Control Filed
32'h 0000_0000 - No bit reverse is applied
32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as
0:31
This patch removes the bit reversing for SCFG registers in
u-boot. It will be implemented through PBI commands in RCW
.pbi
write 0x570200, 0xffffffff
.end
So other SCFG register could be written in big-endian mode
in u-boot or kernel directly.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Disable the snoop for slave interface 0, 1 and 2
to avoid the interleaving on the CCI400 BUS.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define USB configs for LS1021XA such as CONFIG_SYS_FSL_USB1_ADDR,
CONFIG_USB_MAX_CONTROLLER_COUNT
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Ideally, the Linux kernel should get the hardware in its most
untouched state. For the most part, U-Boot does not reset the various
subsystems it touches before boot, and usually Linux deals with it, but
on some boards (cm_fx6) the Linux kernel fails to detect the ssd
correctly if sata is used by U-Boot.
Power off sata on OS boot so that Linux will have a clean state to work
with.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Add reset_sata() to the sata driver interface and implement it
for dwc_ahsata. This function cleans up after sata_init(), and
therefore accepts a device number like sata_init() does.
A dummy implementation is provided for the rest of the drivers.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Older Linux kernels will not properly boot in hyp mode, add support for a
bootm_boot_mode environment variable, which can be set to "sec" or "nonsec"
to force booting in secure or non-secure mode when build with non-sec support.
The default behavior can be selected through CONFIG_ARMV7_BOOT_SEC_DEFAULT,
when this is set booting in secure mode is the default. The default setting
for this Kconfig option is N, preserving the current behavior of booting in
non-secure mode by default when non-secure mode is supported.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Add arch/arm/cpu/armv7/Kconfig with non-secure and virt options, this is a
preparation patch for adding an env variable to choose between secure /
non-secure boot on non-secure boot capable systems, specifically this
prepares for adding CONFIG_ARMV7_BOOT_SEC_DEFAULT as a proper Kconfig option.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Change the internal sandbox functions to use loff_t for file offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some tegra makefiles only contain a dummy line to generate
a built-in.o. Let's do not descend into such directories.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
The references of CONFIG_SYS_COREBOOT in arch/x86/cpu/coreboot/Makefile
are redundant because the build system descends into the directory
only when CONFIG_SYS_COREBOOT is defined.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Some CPUs of some architectures have SOC directories.
At present, the build system directly descends into SOC directories
from the top Makefile, but it should generally descend into each
directory from its parent directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
bcm911360_entphn
bcm911360_entphn-ns
bcm911360k
bcm958300k-ns
bcm958305k
- updates to support Cygnus and NSP board families better
- add functions so CONFIG_ARMV7_NONSEC can be enabled on Cygnus boards
Signed-off-by: Steve Rae <srae@broadcom.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
Move USB Errata checking code from "arch/powerpc" to architecture independent
file "fsl_usb.h" so that errata(s) become independent of the architecture.
For each erratum checking function for PPC arch, define a nop function for
non PPC arch for successful compilation in either case
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add imx6 thermal device to mx6 soc file. Read the cpu temperature
using this device to access onchip thermal sensor.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Add api to check and enable pll3 as required
for thermal sensor driver.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
The linker lists feature is useful in SPL as it holds the driver model
platform data. So don't throw away the lists.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
For SPL it is sometimes useful to have a simple malloc() just to permit
driver model to work, in the cases where the full malloc() is not made
available by the board config.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add driver model support while retaining the existing legacy code. This
allows the driver to support boards that have converted to driver model
as well as those that have not.
Signed-off-by: Simon Glass <sjg@chromium.org>
These boards all have the same GPIO arrangement, so add some common platform
data that can be used by all boards. Remove the configs which are no longer
required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Modify this driver to support driver model, with platform data required to
determine the GPIOs that it controls.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename this vendor since it is intended to be used on any platform where
coreboot runs at reset and then loads U-Boot.
So far it is only tested on link. When other boards are supported it is
likely that we will need to move to multiple board names, all under the
'coreboot' vendor. So while it would be possible to remove the vendor for
now, that would be short-sighted.
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement SDRAM init using the Memory Reference Code (mrc.bin) provided in
the board directory and the SDRAM SPD information in the device tree. This
also needs the Intel Management Engine (me.bin) to work. Binary blobs
everywhere: so far we have MRC, ME and microcode.
SDRAM init works by setting up various parameters and calling the MRC. This
in turn does some sort of magic to work out how much memory there is and
the timing parameters to use. It also sets up the DRAM controllers. When
the MRC returns, we use the information it provides to map out the
available memory in U-Boot.
U-Boot normally moves itself to the top of RAM. On x86 the RAM is not
generally contiguous, and anyway some RAM may be above 4GB which doesn't
work in 32-bit mode. So we relocate to the top of the largest block of
RAM we can find below 4GB. Memory above 4GB is accessible with special
functions (see physmem).
It would be possible to build U-Boot in 64-bit mode but this wouldn't
necessarily provide any more memory, since the largest block is often below
4GB. Anyway U-Boot doesn't need huge amounts of memory - even a very large
ramdisk seldom exceeds 100-200MB. U-Boot has support for booting 64-bit
kernels directly so this does not pose a limitation in that area. Also there
are probably parts of U-Boot that will not work correctly in 64-bit mode.
The MRC is one.
There is some work remaining in this area. Since memory init is very slow
(over 500ms) it is possible to save the parameters in SPI flash to speed it
up next time. Suspend/resume support is not fully implemented, or at least
it is not efficient.
With this patch, link boots to a prompt.
Signed-off-by: Simon Glass <sjg@chromium.org>
The local advanced programmable interrupt controller is not used much in
U-Boot but we do need to set it up. Add basic support for this, which will
be extended as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
When not relying on Coreboot for GPIO init the GPIOs must be set up
correctly. This is currently done statically through a rather ugly method.
As the GPIOs are figured out they can be moved to the device tree and set
up as needed rather than all at the start.
In this implementation, board files should call ich_gpio_set_gpio_map()
before the GPIO driver is used in order to provide the GPIO information.
We use the early PCI interface so that this driver can now be used before
relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add two microcode updates that are provided for this CPU. The updates
have been converted to a device tree form.
Note: SPDX submission has been done. If this license is approved I will
convert the files to use SPDX.
Signed-off-by: Simon Glass <sjg@chromium.org>
The built-in self test value should be checked before we continue booting.
Refuse to continue if there is something wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is convenient to be able to adjust MSRs with a structure that splits the
two 32-bit halves into separate fields, as they are often dealt with
separately. Add a few functions to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no need to explicitly write 'arch-coreboot' when including headers,
as when the arch directory points to coreboot the correct files will be
used.
Signed-off-by: Simon Glass <sjg@chromium.org>
The PCH (Platform Controller Hub) includes an LPC (Low Pin Count) device
which provides a serial port. This is accessible on Chromebooks, so enable
it early in the boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add simple PCI access routines for x86 which permit use before relocation.
The normal PCI stack is still used, but for pre-relocation use there can
only ever be a single hose. After relocation, fall back to the normal
access, although even then on x86 machines there is normally only a single
PCI bus.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for using PCI before SDRAM is available, using early malloc()
and global_data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We want access PCI earlier in the init sequence, so refactor the code so
that it does not require use of a BSS variable to work. This will allow us
to use early malloc() to store information about a PCI hose.
Common PCI code moves to arch/x86/cpu/pci.c and a new
board_pci_setup_hose() function is provided by boards to set up the (single)
hose used by that board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for CAR so that we have memory to use prior to DRAM init.
On link there is a total of 128KB of CAR available, although some is
used for the memory reference code.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 it is common to use 'post codes' which are 8-bit hex values emitted
from the code and visible to the user. Traditionally two 7-segment displays
were made available on the motherboard to show the last post code that was
emitted. This allows diagnosis of a boot problem since it is possible to
see where the code got to before it died.
On modern hardware these codes are not normally visible. On Chromebooks
they are displayed by the Embedded Controller (EC), so it is useful to emit
them. We must enable this feature for the EC to see the codes, so add an
option for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On x86 machines U-Boot needs to be added to a large ROM image which is
then flashed onto the target board. The ROM has a particular format so it
makes sense for U-Boot to build this image automatically. Unfortunately
it relies on binary blobs so we cannot require this for the default
build as yet.
Create a u-boot.rom output file for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
This board is a 'bare' version of the existing 'link 'board. It does not
require coreboot to run, but is intended to start directly from the reset
vector.
This initial commit has place holders for a wide range of features. These
will be added in follow-on patches and series. So far it cannot be booted
as there is no ROM image produced, but it does build without errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Unfortunately MSR_FSB_FREQ is not available on this CPU, and the PIT method
seems to take up to 50ms which is much too long.
For this CPU we know the frequency, so add another special case for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The references of CONFIG_SYS_COREBOOT in arch/x86/cpu/coreboot/Makefile
are redundant because the build system descends into the directory
only when CONFIG_SYS_COREBOOT is defined.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This implementation has a 'cpu' prefix and returns a pointer to the string,
avoiding the need for copying.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function to get the stack pointer and another to halt the CPU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Return the saved TSC frequency in get_tbclk_mhz().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Use the same way that Linux does for quick TSC calibration via PIT
when calibration via MSR fails.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Using MSR_PLATFORM_INFO (0xCE) to calibrate TSR will cause #GP on
processors which do not have this MSR. Instead only doing the MSR
calibration for known/supported CPUs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
