This add the boot menu option for the NYMPH baseboard as well as a
specific config file for users which wish to use it as a pre-defined
board.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This add the boot menu option for the DWARF baseboard as well as a
specific config file for users which wish to use it as a pre-defined
board.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This add the boot menu option for the NYMPH baseboard as well as a
specific config file for users which wish to use it as a pre-defined
board.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.
Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]
So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.
Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.
[1] https://lists.denx.de/pipermail/u-boot/2019-April/364057.html
Reported-by: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
As per Linux kernel DT binding doc:
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
a delay of phy-reset-post-delay milliseconds will be observed after the
phy-reset-gpios has been toggled. Can be omitted thus no delay is
observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Negative phy-addresses can occour if the caller function was not able to
determine a valid phy address (from device-tree for example). In this
case we catch this here and search for ANY phy device on the given mdio-
bus.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
This add the boot menu option for the DWARF baseboard as well as a
specific config file for users which wish to use it as a pre-defined
board.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The default U-Boot environment expects the use of eMMC user
partition. To ensure we are using the proper eMMC partition for boot
we need to run the `mmc partconf` command.
This patch updates the README instructions to avoid users to follow
misleading instructions.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Parts of the code are using C99 constructs (such as variables declared
inside loops), but also GNU extensions (such as typeof), so using
-std=gnu99 is necessary to build with older versions of gcc that don't
default to building with gnu99.
It fixes the following build failure:
./tools/../lib/crc16.c: In function "crc16_ccitt":
./tools/../lib/crc16.c:70:2: error: "for" loop initial declarations are only allowed in C99 mode
for (int i = 0; i < len; i++)
^
./tools/../lib/crc16.c:70:2: note: use option -std=c99 or -std=gnu99 to compile your code
when building the host tools with gcc 4.7.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The Khadas VIM2 defconfig was missing the USB PHY config and
two other misc configs to setup dram banks and call misc_init_r.
Align it on the other Amlogic SoC based boards defconfig.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The MESON_GXL_USB_PHY is also used on the Amlogic Meson GXM SoCs.
Fixes: 2960e27e38 ("phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
* imx/master:
DTS: Fix ETH PHY reset on HSC|DDC boards (imx53)
cosmetic: Remove not needed string from kp_imx53.h config
cosmetic: config: Remove empty #ifdefs
imx8mq_evk: README: Make the underline marker fill the whole sentence
imx8mq_evk: README: Fix a typo in the destination path
imx8mq_evk: README: Need to copy bl31.bin to U-Boot source tree
tools/imx8m_image.sh: remove bashism
Add the TechNexion's logo from their internal U-Boot tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Use the 'hdmidetect' command in U-boot to load the appropriate
video arguments. If HDMI is connected during boot then make HDMI
as the primary framebuffer, otherwise let LVDS be the primary framebuffer.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Generate kernel video bootargs for sabresd, based on a list of needed video
interfaces ("video_interfaces" U-Boot env-var). The order of initialization
and video settings can be fully customized.
Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Fix missing at91 boards and split the at91 in two categories:
at91 arm v7
at91 arm926esj
which are the two main cores for the at91 architecture.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
After the commit: "eth: dm: fec: Add gpio phy reset binding"
SHA1: efd0b79106
The FEC ETH driver switched to PHY GPIO reset performed with data defined
in DTS.
For the HSC|DDC boards the GPIO reset signal is active low and hence the
wrong DTS description must be changed (otherwise the reset for ETH is not
properly setup).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After running tools/moveconfig.py it turned out that for various boards
there are an empty #ifdef statements.
Remove them to clean u-boot source code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After building ATF it is needed to copy the generated bl31.bin file to
the U-Boot source tree.
Make this step explicit in the instructions.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
CLK_AHB_GMAC was suppose to be part of previous commit
"clk: sunxi: Implement A10 EMAC clocks" add it so-that
we can get rid of sunxi_set_gate warning on boot message.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Use a single '=' to test string equality for compatibility with non-bash
shells. Otherwise, if /bin/sh is dash, build fails:
./tools/imx8m_image.sh: 15: [: signed_hdmi_imx8m.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: signed_hdmi_imx8m.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: spl/u-boot-spl-ddr.bin: unexpected operator
./tools/imx8m_image.sh: 15: [: spl/u-boot-spl-ddr.bin: unexpected operator
WARNING './spl/u-boot-spl-ddr.bin' not found, resulting binary is not-functional
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Chris Spencer <christopher.spencer@sea.co.uk>
- pico-imx6ul: fix after conversion
- engicam boards
- pico-imx7d _ README due to hang with imx-usb-loader
-----BEGIN PGP SIGNATURE-----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=TWtH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190401' of git://git.denx.de/u-boot-imx
Fixes for 2019.01
- pico-imx6ul: fix after conversion
- engicam boards
- pico-imx7d _ README due to hang with imx-usb-loader
Since commit 9e3c0174da ("pico-imx7d: Add LCD support") we started to
notice some hangs in U-Boot.
There is not an issue on such commit per se, but due to the LCD support
the current drawn is increased and this may cause issues when powering
pico-imx7d-pi from USB.
Some computers may be a bit strict with USB current draw and will
shut down their ports if the draw is too high.
The solution for that is to use an externally powered USB hub between the
board and the host computer.
Add such recommendation to the README file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
SRAM address used for bootcount on exiting code is erasing
previous count value when system reset from Linux. So use
the dedicated imx6 scratch register, GPR2 to preserve the
contents even if the system reset from Linux.
Fixes: 4eb9aa3935 ("configs: imx6qdl_icore_mmc: Enable watchdog and bootcounter")
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
SPL on Engicam i.Core M6 boards enabled DM, so it would require some
malloc() pool before relocation in order to load U-Boot proper properly.
So, enable SPL malloc() pool of 0x2000 size similarly like what we have
used for icore mmc defconfigs.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With UUID support, the root can now point to UUID. This makes
swiching between mmc 0 and mmc 1 easier by simplying changing
mmcdev between 0 and 1. From there, the scripts handle the rest.
Signed-off-by: Adam Ford <aford173@gmail.com>
After the DM_MMC conversion the following eMMC boot error is observed:
U-Boot SPL 2019.04-rc4 (Mar 20 2019 - 18:53:28 +0000)
Trying to boot from MMC1
MMC Device 0 not found
spl: could not find mmc device 0. error: -19
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This happens because the SPL code does not initialize the SDHC pins
and clock.
Fix it by moving the original eMMC initialization from U-Boot proper
to SPL.
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
- reverts the deprecation of the 'download-key' detection
(with a full solution pending for the next release)
- applies a temporary fix for the 32bit pinctrl registers on the RK3288
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcnoA9AAoJECaAFcEOcohNRYYH/0SAGKro+gO1q07xpBLGbOSL
MJPNDQ853IpH+kI+Mc+VFeFZz8fuQHae2aKfgmHmEGGSygFqAKXvMUgG73XO8Z27
Ov9r0RgR5s35eXFC0URqcDSCuTtFSP/MdmSy2hO546pJOapHhmx/eZUId3ZFjSe5
puIQfTxK0zbNqfFlfjsRnkXhR9jhYVvPtSpFYYjCeU/dRB4/OUzNHQjwjkdB8ru1
mTLmrhqqZ4fq3t9JMrxCH3COvI6QYBXj73ynKYtJ4lByh3NdIz0a37F99FiWgH2X
0WptUN8tjjZP+2BboVNo6io/12YxE6V+wG2LGEXreS9ubMr4nm+LXqDCoZIB7MM=
=ESBv
-----END PGP SIGNATURE-----
Merge tag 'rockchip-fixes-for-2019.04' of git://git.denx.de/u-boot-rockchip
Last-minute fixes for Rockchip for 2019.04:
- reverts the deprecation of the 'download-key' detection
(with a full solution pending for the next release)
- applies a temporary fix for the 32bit pinctrl registers on the RK3288
