The PCI_REGION_MEMORY and PCI_REGION_MEM are a bit to similar and
can be confusing when reading the code.
Rename PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY to clarify its used
for system memory mapping purposes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
M5271 dynamic clock multiplier. It is currently fixed at 100MHz.
Allow the board header file to set their own multiplier and divider.
Added the #define for the multiplier and divider to the cpu header file.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Discontinue the use of CONFIG_SYS_FECI2C (only used by M5271EVB).
Use read-modify-write to activate the FEC pins without disabling I2C.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Added the CONFIG_M5271 to the list of Coldfire V2 processor. This
was causing the bus clock (not CPU clock) to be declared twice as
fast as it actually is. This causes UARTS to operate at half the
specified baudrate.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
On some platforms PCIE support is not required, but would be included
because the cpu supports it. To reduce fooprint it is now configurable
via CONFIG_PCI_DISABLE_PCIE.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the fdt UART clock fixup code to
only touch CPU internal UARTs on 4xx systems.
Only these UARTs are definitely clocked by gd->uart_clk.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Previously, booting over the UART required the baud rate to be known ahead
of time. Using a bit of tricky simple math, we can calculate the new board
rate based on the old divisors.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Newer Blackfin boot roms support using the fast SPI read command rather than
just the slow one. If the functionality is available, then use it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some bits of the DDR MMRs should not be set. If they do, bad things may
happen (like random failures or hardware destruction).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Newer Blackfin's have an on-chip rom with a syscontrol() function that needs
to be used to properly program the memory and voltage settings as it will
include (possibly critical) factory tested bias values.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
IIM (IC Identification Module) is the fusebox for the mpc5121.
Use #define CONFIG_IIM to turn on the clock for this module
use #define CONFIG_CMD_FUSE to add fusebox commands.
Fusebox commands include the ability to read
the status, read the register cache, override the register cache,
program the fuses and sense them.
Signed-off-by: Martha Marx <mmarx@silicontkx.com>
Signed-off-by: John Rigby <jrigby@freescale.com>
Take the cache flush functions from the kernel as they use hardware loops in
order to get optimal performance.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Start building all Blackfin boards with -ffunction-sections/-fdata-sections
and linking with --gc-sections.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
instead the board will have to load it from flash or ram
which will be specified by npe_ucode env var
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Rather than forcing people to define a custom "LITTLEENDIAN", just use the
__LITTLE_ENDIAN one from the Linux byteorder headers that every arch is
already setting up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Some devices have no UART device pulled out, so allow people to disable the
driver completely in favor of other methods (like JTAG-console).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin JTAG has the ability to pass data via a back-channel without
halting the processor. Utilize that channel to emulate a console.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Make sure we save the value of RETX at power on and then pass it on to the
kernel so that it can nicely debug a "double-fault-caused-a-reset" crash.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
People often ask questions about the init process and when things go
from flash to relocated base, so clarify the comments a bit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
As pointed out by Ivan Koryakovskiy, the initialization code was not
actually respecting the CONFIG_CLKIN_HALF option when configuring the
PLL_CTL register.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current Blackfin i2c driver does not work properly with certain devices
due to it breaking up transfers incorrectly. This is a rewrite of the
driver and relocates it to the newer place in the source tree.
Also remove duplicated I2C speed defines in Blackfin board configs and
disable I2C slave address usage since it isn't implemented.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Our dcache invalidate function doesn't just invalidate, it also flushes.
So rename the function accordingly and fix the dma_memcpy() function so it
doesn't inadvertently corrupt the data destination.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch adds flush_/invalidate_dcache_range() to the MIPS architecture.
Those functions are needed for the upcoming dcache support for the USB
EHCI driver. I chose this API because those cache handling functions are
already present in the PPC architecture.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Added support for a second memory bank to DDR autodetection for 440
platforms.
Made hardcoded values configurable.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This change is needed for mgcoge because it uses two ethernet drivers.
Add a check for the presence of the PIGGY board on mgcoge. Without this
board networking cannot work and the initialization must be aborted.
Only allocate rtx once to prevent DPRAM exhaustion.
Initialize ether_scc.c and the keymile-specific HDLC driver (to be added
soon) in eth.c.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
