There is no need for it to be non-constant. Making it constant, allows to
return constant string without warning.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to apply an overlay to a DTB. The DTB must have been generated
with the option '-@'.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are many ways the overlay application can fail.
2 of them are probably the most common:
- the application itself failed. Usually this is comes from an unresolved
reference
- DTBO not available in FIT (could be because of a typo)
In both case it is good to be more explicit about the error and at least
show which overlay is failing.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If one overlay that must be applied cannot be found in the FIT, the current
implementation stops applying the overlays. Let's make it skip only the
failing overlay instead.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the node describing an overlay does not specify a load address, it will
be loaded at the address previously used.
Fixing it by allocating a temporary buffer that will be used as a
default load address. By default, the size of the buffer is 64kB which
should be plenty for most use cases.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make room in the FDT before applying the overlay, otherwise it may fail if
the overlay is big. As the exact added size is not known in advance, just
add the size of the overlay.
Move after the end of the application of the overlays, the resize of the
FDT for the injection of the details on the loadables.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
doc/uImage.FIT/overlay-fdt-boot.txt is describing how to create FIT
image with DT overlays in it.
Add support for this feature to SPL.
Here is the ZynqMP fragment where dtb points to full DT and dtbo is
overlay which should be applied on the top of dtb.
config {
description = "ATF with full u-boot overlay";
firmware = "atf";
loadables = "uboot";
fdt = "dtb", "dtbo";
};
The whole feature depends on OF_LIBFDT_OVERLAY which is adding +4kB code
and 0 for platforms which are not enabling this feature.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When u-boot.img is a FIT image generated automatically by mkimage, the
configuration node has the following structure:
conf-1 {
description = "k3-am654-base-board";
firmware = "firmware-1";
loadables = "firmware-1";
fdt = "fdt-1";
};
The firmware is referenced twice. Once by the 'firmware' property and
once by the 'loadables' property. Currently this result in the firmware
being loaded twice. This is not a big problem but has an impact on the
boot time.
Fixing it by not loading a loadable image if it is also the firmware image.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
This has the same result but some compilers will warn about this
fall-through if there are statements as part of the label block.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This is very similar to fit_image_get_data but has the benefit of working
on FIT images with external data unlike fit_image_get_data. This is
useful for extracting sub-images from type of FIT image as this would
previously just silently fail. Add an error message also so if this
still fails it is easier to find out why.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The dumpimage utility errors out in a number of places without providing
sufficient feedback to allow the user to easily determine what has gone
wrong. Add additional error messages to make the cause of the failure
more obvious.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeFDfVAAoJEB6zHgIOrC/IKfsH/2cUfXuc9IgA7L90L3g7htlS
zLAQSC8Xk0WbgbmBJh/lq6zFWj2Mu2yfkZqRzwN8bHkmOPq40F+pEAszVtjH77HM
FpSjMSDVWfNXuhmoiS571dehA0TGi1b2kknrAXqpOwVuMRncMCwaPi8yZYZSGlSV
VzMtguQxD0sZg4oMZVde3tCd41smPTPNDjzLZnXdLa0b09+EtW6enGuk3vzXlS/8
QUT68wUzkeoptJhf3pQ3BXNvkFwdNdYJ74uevDmkAYtvxyl10WNykcwYmH50Q9qq
9plF11EizmTHlj16rWpZLx66RP0s4pziKaeGMr6S8uln33Cr9N496wPqtuDBnvA=
=FYPj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.04 cycle
This feature set is a patch series from Tudor Ambarus which includes
parsing of the spi flash SFDP parser for SST flashes, and using those
tables to retrieve unique saved per device MAC address. This is then
used as base mac address on the SAMA5D2 Wireless SOM EK board.
It's true that booting normally doesn't take long enough for the
register to roll (which actually happens in a little over an hour, not
just a few seconds). However, the counter starts at power-on, and if
the board is held in reset to be booted over USB, one actually risks
hitting wrap-around during boot, which can both result in too short
delays (if the "st += delay" calculation makes st small) and
theoretically also unbound delays (if st ends up being UINT_MAX and
one just misses sampling digctl_microseconds at that point).
It doesn't take more code to DTRT, and once bitten, twice shy.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Engicam i.CoreM6 1.5 Quad/Dual MIPI dtsi is reusing fec node
from Engicam i.CoreM6 dtsi but have sampe copy of phy-reset-gpio
and phy-mode properties.
So, drop this phy reset methods from imx6qdl-icore-1.5 dsti file.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation is based on
the 1.5 version of the i.Core MX6 cpu module. The 1.5 version
differs from the original one for a few details, including the
ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup
do to un-clocked PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Similar fix has merged for i.Core MX6Q but missed to update for DL.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync Engicam device tree file from v5.4 linux-next.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Now all the fec related phy properties are now accessible
via dts. So drop the explicit config items from common
config file, imx6-engicam.h
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
According to the SOM and reference board the clock
can be taken from the external pin or provided from
ENET_REF_CLK. Add a new function that make the proper
set according the board type.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Make easy to map fdt file to board in order to use
this information later to apply specific change to
specific board combination.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The data sheet says that the DIV field cannot change while the CLKGATE
bit is set or modified. So do it a little more carefully, by first
clearing the bit, waiting for that to appear, then setting the DIV
field.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The comment says to clear the bypass bit, but in fact it sets it, thus
selecting ref_xtal. And the next line of code does not set the divider
to 12, but to (the reset value of) 1.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
I tried clearing a bit by writing to hw_clkctrl_gpmi_clr, then
busy-waiting for it to actually clear. My board hung. The data sheet
agrees, these registers do not have _set, _clr, _tog, so fix up the
definitions. git grep -E 'clkctrl_(gpmi|ssp[0-9])_' says that nobody
uses those non-existing ops registers.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Adjust the environment for booting a mainline kernel by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add info about supported i.MX7, improve details the usage of
bcbonly subcommand.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When pmic_get() is used with DM the first parameter must be
the complete node name plus the unit address, so fix it
accordingly.
Reported-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In cases when the same SPL should run on boards with i.MX8MM, that
differ in DDR configuration, it is necessary to try different
parameters and check if the training done by the firmware suceeds or
not.
Therefore we return the DDR training/initialization success to the
upper layer in order to be able to retry with different settings if
necessary.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The DDR firmware binaries are not part of the U-Boot source code, so
we should look for them in the build directory, where they need to be
copied to before building U-Boot.
The ATF binary is already fetched from the build directory, but the
README files for the i.MX8M EVKs claim that it needs to be copied to
the source directory (which is still true for in-tree builds, but not
in general). Therefore we also fix the READMEs to use the build
directory as the correct location for all additional binary files.
Sined-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In the case of i.MX6 and i.MX7 family SoCs it is safe (from an errata
point of view) to use thumb2 by default to save space.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently imx-specific bootaux command doesn't support ELF format
firmware for Cortex-M4 core.
This patches introduces a PoC implementation of handling elf firmware
(load_elf_image_phdr() was copy-pasted from elf.c just for PoC).
ELF64 binaries isn't supported yet.
This has the advantage that the user does not need to know to which
address the binary has been linked to. However, in order to handle
and load the elf sections to the right address, we need to translate the
Cortex-M4 core memory addresses to primary/host CPU memory
addresses (Cortex A7/A9 cores).
This allows to boot firmwares from any location with just using
bootaux, e.g.:
> tftp ${loadaddr} hello_world.elf && bootaux ${loadaddr}
Similar translation table can be found in the Linux remoteproc
driver [1].
[1] https://elixir.bootlin.com/linux/latest/source/drivers/remoteproc/imx_rproc.c
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Sync DTS with the mainline Linux and introduce fec node and
regulator configuration for rn5t567 PMU.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Sync DTS with the mainline Linux and introduce fec node.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Sync DTS with the mainline Linux and introduce fec node.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Take over maintainership for colibri_imx6/imx6ull/t30/vf modules.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Take over maintainership for apalis_imx6 and colibri_imx6 modules.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
The Embedded Artists COM board is based on NXP i.MX7ULP.
It has a BD70528 PMIC from Rohm with discrete DCDC powering option and
improved current observability (compared to the existing NXP i.MX7ULP EVK).
Add the initial support for the board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
We switch from custom boot commands relying on uEnv.txt to distro boot.
This removes the automatic fpga bitstream loading in favor of loading
bitstreams via custom bootscripts (boot.scr) or after booting the
kernel.
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
