When CONFIG_$(SPL_)CLK not defined, the clock controller device
not exist, so to avoid boot failure for platform not have
CONFIG_$(SPL_)CLK, add a check.
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MN support loading images with rom api, so we implement
reuse board_return_to_bootrom to let ROM loading images.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set the BYPASS ID SWAP bit (GPR10 bit 1) in order for GPU not to
generated AXI bus errors with TZC380 enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MN has similar architecture with i.MX8MM, so it could reuse
the clock code of i.MX8MM, but i.MX8MN has different CCM root
configurations, so need a separate root entry.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
lpuart0 is the uart used by SPL and U-Boot proper, and DM_SERIAL
is enabled. Since uclass power domain is also enabled, to make
lpuart work properly, need add u-boot,dm-spl for lpuart power domain
and its parent.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
with u-boot,dm-spl added for imx8qm-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add subcommand for add writing BCB only, where we provide appropriate
offsets for firmware1 and firmware2 and size.
Example of usage:
> nandbcb bcbonly 0x00180000 0x00080000 0x00200000
Writing 1024 bytes to 0x0: randomizing
OK
Writing 1024 bytes to 0x20000: randomizing
OK
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Move code for writing FCB/DBBT pages to a separate function
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add support for updating FCB/DBBT on i.MX7:
- additional new fields in FCB structure
- Leverage hardware BCH/randomizer for writing FCB
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This commit adds support for the brppt2 board. The board is based on the
i.mx6 dual-lite SoC.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Borrow ID reading code from Ye Li (NXP U-Boot, commit ID 5b443e3e2617)
but drop imx-mkimage commit ID reading since we now use in tree mkimage.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Need to pass total 5 arguments for SIP HAB call on i.MX8MQ,
so update the interface to add new argument.
Signed-off-by: Ye Li <ye.li@nxp.com>
[agust: fixed imx8m-power-domain build]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add function and new command "auth_cntr" for secure boot support.
When booting with life cycle set to OEM closed, we need to use
this function to authenticate the OS container and load kernel & FDT
from OS container to their destination.
Also add image authentication call when loading container images.
Users can set CONFIG_AHAB_BOOT=y to enable the feature. It is not
set at default.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for
DRAM and linux suspend voltage requirement.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
It will be easy to separate SD/EMMC when booting in SPL stage, then
no need to bother which device is BOOT_DEVICE_MMC1/2.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add init_nand_clk to enable gpmi nand clock. Since i.MX8MQ not use CCF,
so we still use legacy mode to configure the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The i.MX8MQ B1 uses OCOTP_HW_OCOTP_READ_FUSE_DATA register for chip id.
It returns a magic number 0xff0055aa. update get_cpu_rev to support it,
and enable ocotp clock to access ocotp.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Migrate to DM_VIDEO, update the device tree and remove code that is no
longer necessary.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Migrate to DM_ETH and remove code that is no longer necessary.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
This updates the i.MX8MQ device trees and, necessarily, also the
i.MX8MQ clock bindings. These are taken verbatim from from the
Linux kernel version v5.4-rc2, which three small changes which
were already part of the previous device tree:
* Keep the PSCI reserved memory range
* Keep the alias for ethernet, so that the MAC address can be set
* Keep the modified #include for the IOMUXC pins
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Acked-by: Peng Fan <peng.fan@nxp.com>
This commit converts mccmon6's u-boot proper (in a single commit to avoid
build breaks) to use solely DM/DTS.
The DTS description of the mccmon6 has been ported from Linux kernel
(v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add u-boot,dm-pre-reloc properties for uart pinmux configuration
nodes, which enables UART as early as possible (before relocation).
Without this we miss almost the half of output (U-boot version,
CPU defails, Reset cause, DRAM details etc.).
Fixes: cd69e8ef9b ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm")
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to
keep original imx6ull-colibri.dts in sync with Linux.
Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi +
additionally fix checkpatch warnings.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
According to IMX28CEC rev. 4, 10/2018, Table 15. Recommended Operating
Conditions, page 16, the VDDD should be set to 1.55V when the CPU is
operating at 454MHz. This is the case in U-Boot, hence increase the
VDDD voltage. This fixes instability when performing TFTP transfers.
Increase the brownout threshold to 1.4V. The documentation recommends
1.45V setting for the brownout, however, this triggers failure during
power block init, so keep the brownout slightly lower.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
imx6_is_bmode_from_gpr9 always returns false, because
IMX6_SRC_GPR10_BMODE is 1<<28 and gets casted to u8 on return.
This moves the function body into imx6_src_get_boot_mode, since that is the
only one using it and it is on the same abstraction level (accessing
registers directly).
Signed-off-by: Claudius Heine <ch@denx.de>