The spi_get_bus_and_cs() may be called on the same bus and chipselect
with different frequency or mode. This is valid usecase, but the code
fails to notify the controller of such a configuration change. Call
spi_set_speed_mode() in case bus frequency or bus mode changed to let
the controller update the configuration.
The problem can easily be triggered using the sspi command:
=> sspi 0:0@1000
=> sspi 0:0@2000
Without this patch, both transfers happen at 1000 Hz. With this patch,
the later transfer happens correctly at 2000 Hz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Documentation:
* man-page for askenv
bug fixes
* correct display of BootOrder in efidebug command
* do not allow TPL_HIGH_LEVEL for CreateEvent(Ex)
* correct handling of unknown properties in SMBIOS tables
-----BEGIN PGP SIGNATURE-----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=ZMB2
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-07-rc5-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-07-rc5-2
Documentation:
* man-page for askenv
bug fixes
* correct display of BootOrder in efidebug command
* do not allow TPL_HIGH_LEVEL for CreateEvent(Ex)
* correct handling of unknown properties in SMBIOS tables
If both POSITION_INDEPENDENT and SYS_RELOC_GD_ENV_ADDR are enabled,
wherever original env is placed anywhere, it should be relocated to
the right address.
Relocation offset gd->reloc_off is calculated with SYS_TEXT_BASE in
setup_reloc() and env address gd->env_addr is relocated by the offset in
initr_reloc_global_data().
gd->env_addr
= (orig env) + gd->reloc_off
= (orig env) + (gd->relocaddr - SYS_TEXT_BASE)
However, SYS_TEXT_BASE isn't always runtime base address when
POSITION_INDEPENDENT is enabled. So the relocated env_addr might point to
wrong address. For example, if SYS_TEXT_BASE is zero, gd->env_addr is
out of memory location and memory exception will occur.
There is a difference between linked address such as SYS_TEXT_BASE and
runtime base address. In _main, the difference is calculated as
"run-vs-link" offset. The env_addr should also be added to the offset
to fix the address.
gd->env_addr
= (orig env) + ("run-vs-link" offset) + gd->reloc_off
= (orig env) + (SYS_TEXT_BASE - _start) + (gd->relocaddr - SYS_TEXT_BASE)
= (orig env) + (gd->relocaddr - _start)
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Commit e4f8e543f1a9("smbios: Drop the unused Kconfig options")
break SMBIOS tables. The reason is that the patch drops the Kconfig
options *after* removing the code using them, but that changes the semantics
of the code completely. Prior to the change a non NULL value was used in
the 'product' and 'manufacturer ' fields.
Chapter 6.2 of the DMTF spec requires Manufacturer and Product Name to be
non-null on some of the tables. So let's add sane defaults for Type1/2/3.
* Before the patchset:
<snip>
Handle 0x0002, DMI type 2, 14 bytes
Base Board Information
Manufacturer: Not Specified
Product Name: Not Specified
Version: Not Specified
Serial Number: Not Specified
Asset Tag: Not Specified
Features:
Board is a hosting board
Location In Chassis: Not Specified
Chassis Handle: 0x0000
Type: Motherboard
Invalid entry length (0). DMI table is broken! Stop.
* After the patchset:
<snip>
Handle 0x0005, DMI type 32, 11 bytes
System Boot Information
Status: No errors detected
Handle 0x0006, DMI type 127, 4 bytes
End Of Table
Fixes: e4f8e543f1 ("smbios: Drop the unused Kconfig options")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We currently define the EFI support of an SMBIOS table as the third bit of
"BIOS Characteristics Extension Byte 1". The latest DMTF spec defines it
on "BIOS Characteristics Extension Byte 2".
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Remove superfluous assignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
help file for using askenv cmd is created.
It provides description on the command purpose,
description of arguments,
couple of examples (illustrating command usage),
configuration parameter and
possible return values.
Signed-off-by: Adarsh Babu Kalepalli <opensource.kab@gmail.com>
Add missing entry in doc/usage/index.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Display the number of the boot option and not its index.
Fixes: 2ecee31017 ("efi_loader: use efi_create_indexed_name()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
According to chapter 7.1 "Event, Timer, and Task Priority Services"
TPL_HIGH_LEVEL should not be exposed to applications and drivers.
According to the discussion with EDK II contributors this implies that
CreateEvent() shall not allow to create events with TPL_HIGH_LEVEL.
Cc: Samer El-Haj-Mahmoud <Samer.El-Haj-Mahmoud@arm.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Samer El-Haj-Mahmoud <Samer.El-Haj-Mahmoud@arm.com>
Unlike imx6, on imx7 the USB PHY is described as:
usbphynop1: usbphynop1 {
compatible = "usb-nop-xceiv";
clocks = <&clks IMX7D_USB_PHY1_CLK>;
clock-names = "main_clk";
#phy-cells = <0>;
};
which does not have the 'reg' property.
Do not return an error when the 'reg' property is not found
for the USB PHY.
This fixes USB gadget regression on a imx7s-warp board.
Successfully tested the "ums 0 mmc 0" command on two boards:
imx7s-warp and imx6dl-pico-pi.
Signed-off-by: Fabio Estevam <festevam@denx.de>
On a imx7s-warp board the fdtdec_get_alias_seq() function
always fails.
As priv->portnr is only used on i.MX6, move fdtdec_get_alias_seq()
inside the CONFIG_MX6 block.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The board detection is incorrectly stating it's an rcar3 variant
instead of an RZ/G2 variant on all the r8a774*1_beacon boards.
Set the flag to correctly display as RZ/G2[M/N/H]
Signed-off-by: Adam Ford <aford173@gmail.com>
- x86: Discard .note.gnu.property sections
- nvme: Skip block device creation for inactive namespaces
- nvme: Convert NVMe doc to reST, and various minor fixes
On some distributions the mkfs is under /sbin and /sbin is not set
for mere users. Include /sbin to the PATH when creating file system,
so that users won't get a scary traceback from Python.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Update to me as co-maintainer with Peng.
Additionally, update the mmc alias in git-mailrc.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
All symbols that are defined in Kconfig will always be defined (or not)
prior to preprocessing due to the -include directive while building.
However, symbols which are not yet migrated will only be defined (or
not) once the board config.h is included, via <config.h>. While the end
goal must be to migrate all symbols, today we have cases where the size
of gd will get mismatched within the build, based on include order.
Mitigate this by making sure that any <asm/global_data.h> that uses
symbols not in Kconfig does start with <config.h>. Remove this when not
needed.
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Based on the comment in socfpga_soc64_common.h, the intention is for
CONFIG_SYS_MEM_RESERVE_SECURE to be unused. However, in the code we do:
...
and that will evaluate to true. This leads to unwanted code being
compiled. Further, as CONFIG_SYS_MEM_RESERVE_SECURE has not been
migrated to Kconfig, this leads to a mismatch in the size of gd
depending on if we have or have not also had <configs/BOARD.h> also
included yet.
Remove the define as it's not needed.
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Chee Hong Ang <chee.hong.ang@intel.com>
Cc: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the changes in commit 588efcdd72fc ("powerpc: Don't use relative
include for config.h in global_data.h") fixing the root of the problem,
we no longer need this re-inclusion.
This reverts commit f6c0d365d3.
Cc: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As there is an arch/powerpc/include/asm/config.h file using "" to get
config.h here can lead to using that rather than include/config.h. This
in turn can lead to a mismatch in the size of gd.
Cc: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
The original code is in the public domain. Licenses/README states that the
general license for U-Boot is GPL 2.0+. So we can mark the malloc code as
GPL 2.0+ too.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This was missed when NVMe support was initially brought to U-Boot
back in 2017. Add an entry for it and list myself as the maintainer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
A udevice's priv space is cleared in alloc_priv() in the DM core.
Don't do it again in its probe() routine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present there is an offset of one added during the creation of
block device. This can be very confusing as we wanted to encode the
namespace id in the block device name but namespae id cannot be zero.
This changes to use the namespace id directly in the block device
name, eliminating the offset of one effectively.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present for each namespace there is a block device created for it.
There is no issue if the number of supported namespaces reported from
the NVMe device is only 1.
Since QEMU commit 7f0f1acedf15 ("hw/block/nvme: support multiple namespaces"),
the number of supported namespaces reported has been changed from 1
to 256, but not all of them are active namespaces. The actual active
one depends on the QEMU command line parameters. A common case is
that namespace 1 being active and all other 255 being inactive.
If a namespace is inactive, the namespace identify command returns a
zero filled data structure. We can use field NSZE (namespace size) to
decide whether a block device should be created for it.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present the block device creation happens in the NVMe uclass
driver post_probe() phase. In preparation to support multiple
namespaces, we should issue namespace identify before creating
block devices but that touches the underlying hardware hence it
is not appropriate to do such in the uclass driver post_probe().
Let's move it to driver probe() phase instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
AQA (Admin Queue Attributes) register is a dword size with
lower word of ASQS, and higher word of ACQS.
The code set the variable aqa twice, but it is redundant.
Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Each prp is 8 bytes, calculate the number of prps
per page should just divide page size by 8
there is no need to minus 1
Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
writel() and co. already include the endian swap; doing the swap twice
is, er, unhelpful.
Tested on a P4080DS, which boots perfectly fine off NVMe with this.
Signed-off-by: David Lamparter <equinox@diac24.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When switching to kernel.org x86_64 gcc 11.1.0 toolchain, u-boot.rom
built from qemu-x86_defconfig no longer boots anymore. Investigation
shows that U-Boot fails at a very early stage during the boot process,
in fdtdec_prepare_fdt() where fdt_check_header() complains that there
is not a valid device tree found at gd->fdt_blob which points to _end.
Now _end points to an allocated section .note.gnu.property which of
course is wrong.
This issue is however not seen when using the default Ubuntu 20.04 gnu
toolchain (gcc 9.3.0 with binutils 2.34). Further investigation shows
that it is caused by a behavior change of binutils v2.36 which is part
of the kernel.org gcc 11.1.0 toolchain, via the following commit:
939b95c77bf2 ("Linux/x86: Configure gas with --enable-x86-used-note by default")
In fact, there was already a regression bug report [1] for binutils two
months ago, but the binutils folks did not think it is a bug :(
To resolve this, there are several options:
* pass -Wa,-mx86-used-note=no to gas
* pass -R .note.gnu.property to objcopy
* discard the section in the linker script
Linux kernel uses the discard way [2], so let's do the same for U-Boot.
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=27753
[2] commit 4caffe6a28d3 ("x86/vdso: Discard .note.gnu.property sections in vDSO")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace typo CONFIG_USE_AUTOBOOT_MENUKEY with
CONFIG_AUTOBOOT_USE_MENUKEY as when they were introduced initially there
was some mismatch in which name was used where.
Fixes: 8fc31e23aa ("autoboot: Rename CONFIG_MENUKEY to CONFIG_AUTOBOOT_MENUKEY")
Signed-off-by: Da Xue <da@libre.computer>
This function is passed *dev not *dev_desc, so pass the right name to
part_init().
Fixes: f14c5ee5ab ("disk: part_dos: update partition table entries after write")
Signed-off-by: Christian Melki <christian.melki@t2data.com>
MSYS2 Windows build started to fail since yesterday (Jun 21):
checking keyring...
checking package integrity...
error: gcc-libs: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust
:: File /var/cache/pacman/pkg/gcc-libs-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)).
error: gcc: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust
:: File /var/cache/pacman/pkg/gcc-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)).
error: failed to commit transaction (invalid or corrupted package)
Errors occurred, no packages were upgraded.
Switching to the latest installer (version 20210604) seems to fix it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com>
This reverts commit 63756575b4.
Since this commit a imx6qdl-pico board boots extremely slowly
in both SPL as well as U-Boot proper.
Fix this regression by reverting the offending commit for now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Pierre-Jean Texier <texier.pj2@gmail.com>
This patch allows uboot scripts make choices about where to boot from based
on the active mmc boot partition. This allows having two copies of kernel,
filesystems etc, and choosing which to boot from based off of the active
bootloader partition.
Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The data read is not working when using FIFO mode.
From DesignWare databook, when a Data_Transfer_Over (DTO) interrupt is
received, the software should read the remaining data from FIFO.
Add DTO interrupt checking on data read path and clear interrupts before
start reading from FIFO. So, it doesn't clear the next pending
interrupts unintentionally after read from FIFO.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tom Rini