Commit Graph

175 Commits

Author SHA1 Message Date
Ashok Reddy Soma
17a42abb40 mmc: Define timing macro's
Define timing macro's for all the available speeds of mmc. This is
done similar to linux. Replace speed macro's used with these new timing
macro's wherever applicable.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-10-27 08:13:33 +01:00
Yangbo Lu
d271e10581 mmc: add a mmc_hs400_prepare_ddr() interface
Add a mmc_hs400_prepare_ddr() interface for controllers
which needs preparation before switching to DDR mode for
HS400 mode.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-10-12 15:46:34 +08:00
Yangbo Lu
8c96880814 mmc: add a hs400_tuning flag
Some controllers may have difference between HS200 tuning
and HS400 tuning, such as different registers setting,
different procedure, or different errata.

This patch is to add a hs400_tuning flag to identify the
tuning for HS400 mode.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-10-12 15:46:32 +08:00
Yangbo Lu
390f9bddb9 mmc: add a reinit() API
For DM_MMC, the controller re-initialization is needed to
clear old configuration for mmc rescan.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-10-12 15:45:39 +08:00
Sean Anderson
68fd602662 mmc: Add mmc_dev()
This macro is necessary for arasan_zynqmp_dll_reset to compile.

Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-09-30 08:52:46 -04:00
Simon Glass
cd93d625fd common: Drop linux/bitops.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
3a905cd231 dm: mmc: Update mmc_get_mmc_dev() to use const *
This function does not modify the device to change it to use const *, so
that callers with a const udevice * can call it without a cast.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-04-24 16:40:09 -04:00
Marek Vasut
145429aac0 mmc: Add option to adjust b_max before long read
Add getter function which permits adjusting the maximum number of
blocks that could be read in a single sustained read transfer based
on the location of the source/target buffer and length, before such
transfer starts.

This is mainly useful on systems which have various DMA restrictions
for different memory locations, e.g. DMA limited to 32bit addresses,
and where a bounce buffer is used to work around such restrictions.
Since the U-Boot bounce buffer is mallocated, it's size is limited
by the malloc area size, and the read transfer to such a buffer must
also be limited. However, as not all areas are limited equally, the
b_max should be adjusted accordinly as needed to avoid degrading
performance unnecessarily.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
2020-04-22 20:41:56 +08:00
Heinrich Schuchardt
0469d84636 cmd: mmc: provide boot area protection command
Provide command 'mmc wp' to power on write protect boot areas on eMMC
devices.

The B_PWR_WP_EN bit in the extended CSD register BOOT_WP is set. The boot
area are write protected until the next power cycle occurs.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-04-22 20:41:55 +08:00
Heinrich Schuchardt
1601ea2126 mmc: export mmc_send_ext_csd()
Export function mmc_send_ext_csd() for reading the extended CSD register.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-04-22 20:41:54 +08:00
Heinrich Schuchardt
9abfe33d10 mmc: EXT_CSD registers for write protection
Add the EXT_CSD register definition related to write protection.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-04-22 20:41:54 +08:00
Faiz Abbas
e8d5dde447 mmc: Merge SD_LEGACY and MMC_LEGACY bus modes
MMC_LEGACY & SD_LEGACY are not differentiated timings in the spec and
don't have any meaningful differences. Therefore, get rid of all
references to SD_LEGACY and use MMC_LEGACY to mean both of them.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-03-09 08:33:16 +08:00
Faiz Abbas
32860bdbc1 mmc: Add a deferred_probe() API
Add a deferred_probe() API for platforms that want to do some
configurations just before starting to enumerate the device.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2020-03-09 08:33:15 +08:00
Faiz Abbas
0d3c858488 mmc: Add a saved_clock member
Add a saved_clock member to struct mmc to store the previous clock speed
in the clock needs to be stopped for some time.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-03-09 08:33:15 +08:00
Masahiro Yamada
bd602c5367 mmc: make <mmc.h> self-contained
This header uses bd_t without including its definition.

Change it to (struct bd_info), and add the forward declaration
to specify it as a structure.

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-03-09 08:33:15 +08:00
Masahiro Yamada
a7b2b6cc0a mmc: add mmc_get_dma_dir() helper
Copied from Linux kernel.
include/linux/mmc/host.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-02-20 15:09:56 +08:00
Joel Johnson
d4a5fa314d mmc: add additional quirk for APP_CMD retry
It was observed (on ClearFog Base) that sending MMC APP_CMD returned
an error on the first attempt. The issue appears to be timing related
since even inserting a puts() short debug entry before the execution
added sufficient delay to receive success on first attempt.

Follow the existing quirks pattern to retry if initial issuance
failed so as to not introduce any delay unless needed.

Signed-off-by: Joel Johnson <mrjoel@lixil.net>
2020-01-16 13:21:01 +08:00
Yann Gautier
3602a56ac6 mmc: add a driver callback for power-cycle
Some MMC peripherals require specific power cycle sequence, where some
registers need to be written between the regulator is turned off and then
back on. This is the case for the MMC IP embedded in STM32MP1 SoC.

In STM32MP157 reference manual [1], the power cycle sequence is:
1. Reset the SDMMC with the RCC.SDMMCxRST register bit. This will reset
the SDMMC to the reset state and the CPSM and DPSM to the Idle state.
2. Disable the Vcc power to the card.
3. Set the SDMMC in power-cycle state. This will make that the
SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are driven low, to prevent the card
from being supplied through the signal lines.
4. After minimum 1ms enable the Vcc power to the card.
5. After the power ramp period set the SDMMC to the power-off state for
minimum 1ms. The SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are set to
drive “1”.
6. After the 1ms delay set the SDMMC to power-on state in which the
SDMMC_CK clock will be enabled.
7. After 74 SDMMC_CK cycles the first command can be sent to the card.

The step 3. cannot be handled by the current framework implementation.
A new callback (host_power_cycle) is created, and called in
mmc_power_cycle(), after mmc_power_off().

The incorrect power cycle sequence has shown some boot failures on
STM32MP1 with some SD-cards, especially on cold boots when the input
frequency is low (<= 25MHz).
Those failures are no more seen with this correct power cycle sequence.

[1] https://www.st.com/resource/en/reference_manual/DM00327659.pdf

Signed-off-by: Yann Gautier <yann.gautier@st.com>
2019-10-10 10:59:48 +08:00
Lokesh Vutla
80f02019ee spl: dm_mmc: Initialize only the required mmc device
In SPL, all the available mmc devices gets initialized during boot.
This might not work in cases where clocks are not available for
certain mmc devices(other than boot device) and the support for
enabling device might not be ready.

Texas Instruments' K3 J721E device having a central system controller
(dmsc) is one such example falling in this category. Below is the
sequence for the failing scenario:
- ROM comes up in SD mode and loads SPL by just initialing SD card.
- SPL loads dmsc firmware from SD Card.
Since ROM has enabled SD, SPL need not enable the SD, just need
to re initialize the card. But SPL is trying to initialize other MMC
instances which are in disabled state. Since dmsc firmware is not yet
available, devices cannot be enabled. So in SPL, initialize only the
mmc device that is needed.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-10 10:59:48 +08:00
Sam Protsenko
6cf8a903c5 mmc: Rename timeout parameters for clarification
It's quite hard to figure out time units for various function that have
timeout parameters. This leads to possible errors when one forgets to
convert ms to us, for example. Let's rename those parameters
correspondingly to 'timeout_us' and 'timeout_ms' to prevent such issues
further.

While at it, add time units info as comments to struct mmc fields.

This commit doesn't change the behavior, only renames parameters names.
Buildman should report no changes at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
2019-09-05 15:27:31 +08:00
Peng Fan
44acd49248 mmc: support hs400 enhanced strobe mode
eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for
tuning procedure.
The flow is as following:
 - set HS_TIMIMG (Highspeed)
 - Host change freq to <= 52Mhz
 - set the bus width to Enhanced strobe and DDR8Bit(CMD6),
   EXT_CSD[183] = 0x86 instead of 0x80
 - set HS_TIMING to 0x3 (HS400)
 - Host change freq to <= 200Mhz
 - Host select HS400 enhanced strobe complete

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15 10:30:08 +08:00
Anup Patel
a897269c93 cmd: Remove mmc_spi command
The mmc_spi command was added to manually setup MMC over SPI bus
using command. This was required by the legacy non-DM MMC_SPI driver.

With DM based MMC_SPI driver in-place, we can now use all general
storge commands and mmc command for MMC over SPI bus hence we remove
the mmc_spi command all it's references.

Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15 10:30:08 +08:00
Jean-Jacques Hiblot
513e00b64e mmc: When switching partition, use the timeout specified in the ext_csd
The e-MMC spec allows the e-MMC to specify a timeout for the partition
switch command. It can take up to 2550 ms. There is no lower limit to this
value in the spec, but do as the the linux driver does and force it to be
at least 300ms.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
39320c537d mmc: use the generic timeout for cmd6 (SWITCH) provided in the ext_csd
Starting with rev 4.5, the eMMC can define a generic timeout for the
SWITCH command.

Following Linux Kernel code, the timeout also changed from 1000 -> 500

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
cd0b80ec9c mmc: if possible, poll the busy state using DAT0
Using the DAT0 line as a rdy/busy line is an alternative to reading the
status register of the card. It especially useful in situation where the
bus is not in a good shape, like when modes are switched.
This is also how the linux driver behaves.

Note of warning: As per the specification, while polling on DAT0 the CLK
must not turned off: "[...] Without a clock edge the Device (unless
previously disconnected by a deselect command (CMD7)) will force the DAT0
line down, forever. [...]"

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
Jean-Jacques Hiblot
c5bda37589 Revert "mmc: Add a new callback function to perform the 74 clocks cycle sequence"
This reverts commit 318a7a576b.

The last and only user of this callback had been the omap_hsmmc driver.
It is not used anymore. Removing the callback.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15 10:16:49 +08:00
T Karthik Reddy
86a94e7b2b mmc: Read sd card detect properties from DT
This patch reads card detect properties from device tree &
added mmc capability macros in mmc.h.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-15 10:16:49 +08:00
Marek Vasut
fceea99268 mmc: Downgrade SD/MMC from UHS/HS200/HS400 modes before boot
Older kernel versions or systems which do not connect eMMC reset line
properly may not be able to handle situations where either the eMMC
is left in HS200/HS400 mode or SD card in UHS modes by the bootloader
and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card
to non-UHS mode before booting the kernel to allow such older kernels
to work with modern U-Boot.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
2019-02-16 18:12:17 +01:00
Rajesh Bhagat
43d17c485f env: fix allow to build multiple environments
Patch fixes build error when enabling CONFIG_ENV_IS_IN_SPI_FLAS
and CONFIG_ENV_IS_IN_MMC at the same time mentioned issue in
below link:

Refer: https://lists.denx.de/pipermail/u-boot/2018-February/319565.html

build error when enabling CONFIG_ENV_IS_IN_SPI_FLASH and
CONFIG_ENV_IS_IN_MMC at the same time.

Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17 13:16:31 -08:00
Jens Wiklander
4853ad3e13 mmc: rpmb: add mmc_rpmb_route_frames()
Adds mmc_rpmb_route_frames() to route RPMB data frames from/to an
external entity.

Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-10-07 10:47:38 -04:00
Peng Fan
3dd2626f48 mmc: add HS400 support
Add HS400 support.
Selecting HS400 needs first select HS200 according to spec, so use
a dedicated function for HS400.
Add HS400 related macros.
Remove the restriction of only using the low 6 bits of
EXT_CSD_CARD_TYPE, using all the 8 bits.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-09-10 20:48:19 -04:00
Jon Nettleton
6c09eba507 mmc: break out get_op_cond code to its own function
This code is useful for testing the existance of devices that
do not have card detect capabilities.  This breaks out the core
functionality and leaves the actual init logic and error reporting
in mmc_start_init().

Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-07-23 10:17:04 +02:00
Baruch Siach
31d9500498 mmc: drop mention of IN_PROGRESS status
The IN_PROGRESS macro has been removed in commit bd47c13583 (mmc: Fix
splitting device initialization). Remove it from the mmc_start_init()
function description.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2018-07-23 10:17:04 +02:00
Jaehoon Chung
6511718254 mmc: add the MMC_CLK_ENABLE/DISABLE macro in mmc.h
mmc_set_clock() function has the disable argument as bool type.
When mmc_set_clock is called, it might be passed to "true" or "false".
But it's too confusion whether clock is enabled or disabled with only
"true" and "false".
To prevent the confusion, replace to MMC_CLK_ENABLE/DISABLE macro from
true/false.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-05-08 13:12:33 +09:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Jean-Jacques Hiblot
ace1bed327 mmc: fix bug in mmc_startup_v4()
The correspondence between mmc versions as used in u-boot and the version
numbers reported in register EXT_CSD_REV is wrong for versions above and
including MMC_VERSION_4_41. All those versions were shifted by one:
real 4.5 hardware appeared to be MMC_VERSION_5_0.

Fix this by adding the missing version in the correspondence table.

Reported-by: eil Eilmsteiner Heribert <eil@keba.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
2018-02-19 16:59:33 +09:00
Jean-Jacques Hiblot
b7a6e2c9c3 mmc: remove hc_wp_grp_size from struct mmc if not needed
hc_wp_grp_size is needed only if hardware partitionning is used.
On ARM removing it saves about 30 bytes of code space.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:24 +09:00
Jean-Jacques Hiblot
173c06dfcc mmc: don't read the size of eMMC enhanced user data area in SPL
This information is only used by the "mmc info" command.
On ARM removing this information from SPL saves about 140 of code space.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:24 +09:00
Jean-Jacques Hiblot
e6fa5a5461 mmc: compile out erase and write mmc commands if write operations are not enabled
Also remove erase_grp_size and write_bl_len from struct mmc as they are
not used anymore. On ARM, removing them saves about 100 bytes of code
space in SPL.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:24 +09:00
Jean-Jacques Hiblot
5b2e72f327 mmc: read ssr only if MMC write support is enabled
The content of ssr is useful only for erase operations.
on ARM, removing sd_read_ssr() saves around 300 bytes.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:24 +09:00
Jean-Jacques Hiblot
f99c2efe56 mmc: make UHS and HS200 optional
Supporting USH and HS200 increases the code size as it brings in IO voltage
control, tuning and fatter data structures.
Use Kconfig configuration to select which of those features should be
built in.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:04 +09:00
Jean-Jacques Hiblot
7abff2c3b3 dm: mmc: update mmc_of_parse()
* convert to livetree API
* don't fail because of an invalid bus-width, instead default to 1-bit.
* recognize 1.2v DDR and 1.2v HS200 flags

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:04 +09:00
Kishon Vijay Abraham I
9215ef5ed5 dm: mmc: Add a library function to parse generic dt binding
Add a new function to parse host controller dt node and
set mmc_config. This function can be used by mmc controller
drivers to set the generic mmc_config.
This function can be extended to set other UHS mode caps
once UHS mode support is added.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:04 +09:00
Jean-Jacques Hiblot
9815e3ba80 mmc: add a library function to send tuning command
HS200/SDR104 requires tuning command to be sent to the card.
Add a simple function to send tuning command and to read and
compare the received data with the tuning block pattern.
This function can be used by platform driver to perform DLL
tuning.
This patch is similar to
commit 996903de92f0 ("mmc: core: add core-level function for
sending tuning commands") added in linux kernel.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:04 +09:00
Jean-Jacques Hiblot
bc1e3272ff mmc: use the right voltage level for MMC DDR and HS200 modes
HS200 only supports 1.2v and 1.8v signal voltages. DDR52 supports 3.3v/1.8v
or 1.2v signal voltages.
Select the lowest voltage available when using those modes.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:04 +09:00
Kishon Vijay Abraham I
83dc42271f mmc: Retry some MMC cmds on failure
With certain SD cards like Kingston 8GB/16GB UHS card, it is seen that
MMC_CMD_ALL_SEND_CID cmd fails on first attempt, but succeeds
subsequently. Therefore, retry MMC_CMD_ALL_SEND_CID cmd a few time
as done in Linux kernel.
Similarly, it is seen that MMC_CMD_SET_BLOCKLEN may fail on first
attempt, therefore retry this cmd a few times as done in kernel.

To make it clear that those are optionnal workarounds, a new Kconfig
option 'MMC_QUIRKS' is added (enabled by default).

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:04 +09:00
Jean-Jacques Hiblot
01298da31d mmc: Change mode when switching to a boot partition
Boot partitions do not support HS200. Changing to a lower performance mode
is required to access them.
mmc_select_mode_and_width() and sd_select_mode_and_width() are modified to
make it easier to call them outside of the initialization context.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12 18:11:04 +09:00
Jean-Jacques Hiblot
04a2ea248f mmc: disable UHS modes if Vcc cannot be switched on and off
If a power cycle cannot be done on Vcc, it is safer not to try the UHS
modes because we wouldn't be able to recover from an error occurring
during the UHS initialization.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:04 +09:00
Jean-Jacques Hiblot
c10b85d6c2 mmc: Add support for UHS modes
Add UHS modes to the list of supported modes, get the UHS capabilites of
the SDcard and implement the procedure to switch the voltage (UHS modes
use 1v8 IO lines)
During the voltage switch procedure, DAT0 is used by the card to signal
when it's ready. The optional card_busy() callback can be used to get this
information from the host driver.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12 18:11:04 +09:00
Kishon Vijay Abraham I
634d484940 mmc: add HS200 support in MMC core
Add HS200 to the list of supported modes and introduce tuning in the MMC
startup process.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12 18:11:04 +09:00