The btrfs implementation methods .ls(), .size() and .read() returns 1 on
failure, but the command handlers expect values <0 on failure.
For example if given a nonexistent path, the load command currently
returns success, and hush scripting does not work.
Fix this by setting return values of these methods to -1 instead of 1 on
failure.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
When CROSS_BUILD_TOOLS is set, set HOSTCFLAGS to CFLAGS otherwise CC
will be used with HOSTCFLAGS which seems wrong
Signed-off-by: Fabrice Fontaine <fontaine.fabrice@gmail.com>
The card detect pin was incorrectly using IRQ_TYPE_LEVEL_LOW
instead of GPIO_ACTIVE_LOW when reading the state of the CD pin.
Without this patch, MMC1 won't be detected.
This is the same patch submitted to linux-omap, but I was hoping
to get it applied to U-Boot without having to wait for the
linux adoption and then backporting.
Fixes: 5448ff33f2 ("ARM: DTS: Resync Logic PD SOM-LV 37xx
devkit with Linux 4.18-RC4")
Signed-off-by: Adam Ford <aford173@gmail.com>
The DM* family of SOCs is no longer supported. We now support the
omap-l138 lcdk board and Lego EV3 platform. Reflect those changes
in the README.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Add am335x-pocketbeagle to CONFIG_OF_LIST in am335x_evm_defconfig.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add device-tree files from linux 5.1-rc7 needed to complete support
for PocketBeagle.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Transition to the IOPAD macros as used in Linux in which the pin mux
mode is specified using a dedicated parameter while also dropping the
related MUX_MODEx macros that are no longer needed. This transition
will allow us to keep both Linux and U-Boot DTS in sync more easily.
While at it also align the file name of the include file itself and
update any references accordingly.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
- at91sam9g20-taurus.dts: use labels
- cleanup taurus port to compile clean with
current mainline again. SPL has no serial
output anymore, so it fits into SRAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
TI-SCI firmware will only respond to messages when the
TI_SCI_FLAG_REQ_ACK_ON_PROCESSED flag is set. Most messages
already do this, set this for the ones that do not.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Alejandro Hernandez <ajhernandez@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
commit 95f4bbd581 ("lib: fdt: Allow LZO and GZIP DT compression in U-Boot")
introduced Kconfig option for gzip in U-Boot, but help text
says gzip for SPL, which is wrong. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
The existing comments where confusing read and write. The comment for
fs_write() had:
"@addr: The address to read into"
So let's rework the comments and format them in Sphinx style.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Switch from using the high priority DMSC transmit message queue used
by the secure R5 MCU island boot context to the low priority message
queue. While the change in priority is irrelevant for the current boot
architecture it however gives us access to a deeper message queue that
will allow us to buffer more messages. This is an important aspect when
sending several messages without requesting and waiting for a response
in a row which is a communication scheme used during core shutdown for
example. See AM654 TISCI User Guide for additional details.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
In commit ad6054f1fe where support for the
Sancloud BeagleBone Enhanced (BBE) was added, new conditional
configuration of either MII pin muxing or RGMII pin muxing is done
depending on the board type. However, the old call to set up MII pin
muxing was not removed.
This may result in misconfiguration of the pin muxing for the BBE or
duplicate configuration for other boards and so we remove this obsolete
call.
Signed-off-by: Paul Barker <paul.barker@sancloud.co.uk>
Restart operation never exists and reset operation never
makes the watchdog expire immediately but expire_now operation
does.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Upcoming sysfw (2019.03) will not open the channelized firewalls during
init, it only going to do so in response to the channel configuration
message.
Remove the channel state checks done before the channel configuration and
move it after the configuration for warning purposes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
An earlier commit converted the TISCI receive timeouts to be specified
in ms rather than us however it failed to take this change into account
when passing the actual timeout to be used when invoking the mailbox
receive API. This leads to the actual timeout to be 1,000 times shorter
than expected and as a result certain TISCI operations would fail.
Fix the issue by converting the timeout declared in ms to us on the fly
as expected by the respective API.
Fixes: fd6b40b1ba ("firmware: ti_sci: Add support for NAVSS resource management")
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the mmc maintainer from Jaehoon to me.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Marek Vasut <marex@denx.de>
Currently packet data is wrongly extracted when metadata is NULL.
Fix it and negate the if check.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
This pull request provides error fixes for the handling of GPT partitions
and for the UEFI subsystem.
-----BEGIN PGP SIGNATURE-----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=GUpA
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc2
This pull request provides error fixes for the handling of GPT partitions
and for the UEFI subsystem.
The random uuid values (enabled via CONFIG_RANDOM_UUID=y) on our
platform are always the same. Below is consistent on each cold boot:
=> ### interrupt autoboot
=> env default -a; gpt write mmc 1 $partitions; print uuid_gpt_misc
...
uuid_gpt_misc=d117f98e-6f2c-d04b-a5b2-331a19f91cb2
=> env default -a; gpt write mmc 1 $partitions; print uuid_gpt_misc
...
uuid_gpt_misc=ad5ec4b6-2d9f-8544-9417-fe3bd1c9b1b3
=> env default -a; gpt write mmc 1 $partitions; print uuid_gpt_misc
...
uuid_gpt_misc=cceb0b18-39cb-d547-9db7-03b405fa77d4
=> env default -a; gpt write mmc 1 $partitions; print uuid_gpt_misc
...
uuid_gpt_misc=d4981a2b-0478-544e-9607-7fd3c651068d
=> env default -a; gpt write mmc 1 $partitions; print uuid_gpt_misc
...
uuid_gpt_misc=6d6c9a36-e919-264d-a9ee-bd00379686c7
While the uuids do change on every 'gpt write' command, the values
appear to be taken from the same pool, in the same order.
Assuming U-Boot with RANDOM_UUID=y is deployed on a large number of
devices, all those devices would essentially expose the same UUID,
breaking the assumption of system/RFS/application designers who rely
on UUID as being globally unique (e.g. a database using UUID as key
would alias/mix up entries/records due to duplicated UUID).
The root cause seems to be simply _not_ seeding PRNG before generating
a random value. It turns out this belongs to an established class of
PRNG-specific problems, commonly known as "unseeded randomness", for
which I am able to find below bugs/CVE/CWE:
- https://bugzilla.redhat.com/show_bug.cgi?id=CVE-2015-0285
("CVE-2015-0285 openssl: handshake with unseeded PRNG")
- https://bugzilla.redhat.com/show_bug.cgi?id=CVE-2015-9019
("CVE-2015-9019 libxslt: math.random() in xslt uses unseeded
randomness")
- https://cwe.mitre.org/data/definitions/336.html
("CWE-336: Same Seed in Pseudo-Random Number Generator (PRNG)")
The first revision [1] of this patch updated the seed based on the
output of get_timer(), similar to [4].
There are two problems with this approach:
- get_timer() has a poor _ms_ resolution
- when gen_rand_uuid() is called in a loop, get_timer() returns the
same result, leading to the same seed being passed to srand(),
leading to the same uuid being generated for several partitions
with different names
The above drawbacks have been addressed in the second version [2].
In its third revision (current), the patch reworded the description
and summary line to emphasize it is a *fix* rather than an improvement.
Testing [3] consisted of running 'gpt write mmc 1 $partitions' in a
loop on R-Car3 for several minutes, collecting 8844 randomly generated
UUIDS. Two consecutive cold boots are concatenated in the log.
As a result, all uuid values are unique (scripted check).
Thanks to Roman, who reported the issue and provided support in fixing.
[1] https://patchwork.ozlabs.org/patch/1091802/
[2] https://patchwork.ozlabs.org/patch/1092945/
[3] https://gist.github.com/erosca/2820be9d554f76b982edd48474d0e7ca
[4] commit da384a9d76 ("net: rename and refactor eth_rand_ethaddr() function")
Reported-by: Roman Stratiienko <roman.stratiienko@globallogic.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Apply the following changes:
- Guard the 'gpt read' command by 'ifdef CONFIG_CMD_GPT_RENAME',
since 'gpt read' is not available on CMD_GPT_RENAME=n
- Prefix the {read,swap,rename} commands with one space for consistency
- Prefix the 'guid' commands with 'gpt' for consistency
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Below is what happens on R-Car H3ULCB-KF using clean U-Boot
v2019.04-00810-g6aebc0d11a10 and r8a7795_ulcb_defconfig:
=> ### interrupt autoboot
=> gpt verify mmc 1
No partition list provided - only basic check
Verify GPT: success!
=> ### keep calling 'gpt verify mmc 1'
=> ### on 58th call, we are out of memory:
=> gpt verify mmc 1
alloc_read_gpt_entries: ERROR: Can't allocate 0X4000 bytes for GPT Entries
GPT: Failed to allocate memory for PTE
gpt_verify_headers: *** ERROR: Invalid Backup GPT ***
Verify GPT: error!
This is caused by calling is_gpt_valid() twice (hence allocating pte
also twice via alloc_read_gpt_entries()) while freeing pte only _once_
in the caller of gpt_verify_headers(). Fix that by freeing the pte
allocated and populated for primary GPT _before_ allocating and
populating the pte for backup GPT. The latter will be freed by the
caller of gpt_verify_headers().
With the fix applied, the reproduction scenario [1-2] has been run
hundreds of times in a loop w/o running into OOM.
[1] gpt verify mmc 1
[2] gpt verify mmc 1 $partitions
Fixes: cef68bf904 ("gpt: part: Definition and declaration of GPT verification functions")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Below is what happens on R-Car H3ULCB-KF using clean U-Boot
v2019.04-00810-g6aebc0d11a10 and r8a7795_ulcb_defconfig:
=> ### interrupt autoboot
=> gpt guid mmc 1
21200400-0804-0146-9dcc-a8c51255994f
success!
=> ### keep calling 'gpt guid mmc 1'
=> ### on 59th call, we are out of memory:
=> gpt guid mmc 1
alloc_read_gpt_entries: ERROR: Can't allocate 0X4000 bytes for GPT Entries
GPT: Failed to allocate memory for PTE
get_disk_guid: *** ERROR: Invalid GPT ***
alloc_read_gpt_entries: ERROR: Can't allocate 0X4000 bytes for GPT Entries
GPT: Failed to allocate memory for PTE
get_disk_guid: *** ERROR: Invalid Backup GPT ***
error!
After some inspection, it looks like get_disk_guid(), added via v2017.09
commit 73d6d18b71 ("GPT: add accessor function for disk GUID"),
unlike other callers of is_gpt_valid(), doesn't free the memory pointed
out by 'gpt_entry *gpt_pte'. The latter is allocated by is_gpt_valid()
via alloc_read_gpt_entries().
With the fix applied, the reproduction scenario has been run hundreds
of times ('while true; do gpt guid mmc 1; done') w/o running into OOM.
Fixes: 73d6d18b71 ("GPT: add accessor function for disk GUID")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In case of a failure exit data may be passed to Exit() which in turn is
returned by StartImage().
Let the `bootefi` command print the exit data string in case of an error.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When printing an UEFI variable an error may arise while converting an
illegal hexadecimal value. In this case a buffer is leaked.
Close the memory leak. Provide an error message.
Reported-by: Coverity (CID 185830)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The field boot OptionalData in structure _EFI_LOAD_OPTIONS is for binary
data.
When we use `efidebug boot add` we should convert the 5th argument from
UTF-8 to UTF-16 before putting it into the BootXXXX variable.
When printing boot variables with `efidebug boot dump` we should support
the OptionalData being arbitrary binary data. So let's dump the data as
hexadecimal values.
Here is an example session protocol:
=> efidebug boot add 00a1 label1 scsi 0:1 doit1 'my option'
=> efidebug boot add 00a2 label2 scsi 0:1 doit2
=> efidebug boot dump
Boot00A0:
attributes: A-- (0x00000001)
label: label1
file_path: .../HD(1,MBR,0xeac4e18b,0x800,0x3fffe)/doit1
data:
00000000: 6d 00 79 00 20 00 6f 00 70 00 74 00 69 00 6f 00 m.y. .o.p.t.i.o.
00000010: 6e 00 00 00 n...
Boot00A1:
attributes: A-- (0x00000001)
label: label2
file_path: .../HD(1,MBR,0xeac4e18b,0x800,0x3fffe)/doit2
data:
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently in do_efi_boot_dump(), we directly read EFI variables from
related environment variables. To accommodate alternative storage
backends, we should switch to using the UEFI API instead.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
UEFI variables should be installed using well-defined API.
Currently we don't support much, but the value of OsIndicationsSupported
will be updated once some features are added in the future.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Add comments. Rename a variable.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI spec requires that freeing of pages fails if the number of pages
to be freed is 'invalid'. Check that it is not zero.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CreateEvent() and CreateEventEx() should check that a notify function is
provided for either of EVT_NOTIFY_SIGNAL or EVT_NOTIFY_WAIT.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
-----BEGIN PGP SIGNATURE-----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=CzWQ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190426' of git://git.denx.de/u-boot-imx
Porting to DM and i.MX8
------------------------
- warp7 to DM
- kp_imx53 to DM
- Warnings in DT
- MX8QM support
- colibri-imx6ull to DM
- imx7d-pico to DM
- ocotp for MX8
To avoid a warning, we need to include the header defining
back_to_bootrom for us.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
After applying the series for debug_uart_init(), Travis-CI reports:
arch/arm/mach-rockchip/rk3399/rk3399.c:90:2: error: implicit declaration of function 'spl_gpio_set_pull' [-Werror=implicit-function-declaration]
spl_gpio_set_pull(&pmugrf->gpio0_p, GPIO(BANK_B, 2), GPIO_PULL_NORMAL);
^~~~~~~~~~~~~~~~~
This is caused by a missing header-file include. Fix it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file for all rockchip SoCs later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Prefer to use structure to access register if we could.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file later for all rockchip SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file for all rockchip SoCs later.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Prefer to use structure to access register if we can.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file later for all rockchip SoCs.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed up header-list to not break FASTBOOT:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use board_debug_uart_init() for UART iomux init instead of
do it in board_init_f, and move the function to soc file so
that we can find all the soc/board setting in soc file and
use a common board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed whitespace error:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable debug uart for kylin board in defconfig.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
All Rockchip SoCs use DEBUG_UART_BOARD_INIT to init per board
UART IOMUX, enable it by default.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The ARCH_SOC name default as 'rockchip' and we put all the
header file in 'arch/arm/include/asm/arch-rockchip/', but
the 'rockchip' is not the SOC name, let's correct it after
we update all the source file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsiich <philipp.tomsich@theobroma-systems.com>