We don't necessarily want to re-enable ctrl-c if it was already disabled
when calling tstc().
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have removed the DocBook files we need to not try and clean
that directory.
Reported-by: ericywl <midnight2903@gmail.com>
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Fixes: 78a88f7930 ("doc: Replace DocBook with sphinx-based docs")
Signed-off-by: Tom Rini <trini@konsulko.com>
Switch to the distro boot for UniPhier platform.
- Remove the environment vairalbes used to load images from raw
block devices.
- Keep the command to download images via tftp. This will be
useful to boot the kernel when no valid kernel image is ready
yet in the file system.
- Use root.cpio.gz instead of root.cpio.uboot because we always know
the file size of the init ramdisk; it is loaded via either a file
system or network.
- Rename fit_addr_r to kernel_addr_r, which the distro command
checks to get the load address of FIT image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable "mtdparts" and "ubi" commands for uniphier_v8_defconfig to
use UBI on NAND devices.
Enable only "mtdparts" for uniphier_{v7,ld4_sld8}_defconfig because
enabling UBI would increase 170KB, which would be memory footprint
problem.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The 'bd' is passed in ft_board_setup() as the second argument.
Replace 'gd->bd' with 'bd'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add 'const' (also 'static' in some places) to struct node_info
arrays to save memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The second argument of fdt_fixup_mtdparts() is an opaque pointer,
'void *node_info', hence callers can pass any pointer.
Obviously, fdt_fixup_mtdparts() expects 'struct node_info *'
otherwise, it crashes run-time.
Change the prototype so that it is compile-time checked.
Also, add 'const' qualifier to it so that callers can constify
the struct node_info arrays.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The NAND framework makes sure to pass in the buffer with at least
chip->buf_align alignment. Currently, the Denali NAND driver only
requests 16 byte alignment. This causes unaligned cache operations
for the DMA transfer.
[Error Example]
=> nand read 81000010 0 1000
NAND read: device 0 offset 0x0, size 0x1000
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
4096 bytes read: OK
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
cherry-pick kernel commit 2ae89c7 (2018-06-05)
to avoid warnings when compiling with GCC 8.1
In file included from scripts/kconfig/zconf.tab.c:2486:
scripts/kconfig/confdata.c: In function ‘conf_write’:
scripts/kconfig/confdata.c:771:22: warning: ‘%s’ directive writing likely 7 or more bytes into a region of size between 1 and 4097 [-Wformat-overflow=]
sprintf(newname, "%s%s", dirname, basename);
^~
scripts/kconfig/confdata.c:771:19: note: assuming directive output of 7 bytes
sprintf(newname, "%s%s", dirname, basename);
^~~~~~
scripts/kconfig/confdata.c:771:2: note: ‘sprintf’ output 1 or more bytes (assuming 4104) into a destination of size 4097
sprintf(newname, "%s%s", dirname, basename);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
scripts/kconfig/confdata.c:774:23: warning: ‘.tmpconfig.’ directive writing 11 bytes into a region of size between 1 and 4097 [-Wformat-overflow=]
sprintf(tmpname, "%s.tmpconfig.%d", dirname, (int)getpid());
^~~~~~~~~~~
scripts/kconfig/confdata.c:774:3: note: ‘sprintf’ output between 13 and 4119 bytes into a destination of size 4097
sprintf(tmpname, "%s.tmpconfig.%d", dirname, (int)getpid());
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The patch
"tools/mkimage: Fix DTC run command to handle file names with space"
(sha1: a6e9810495) contains comma in name
which is confusing patman. Fix it by defining Mirza's email in mailmap.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The NAND offsets for the kernel and U-Boot were missing.
This patch sets up the offsets so the AM3517-EVM can boot from NAND
when DIP switches S7:1 and S7:4 are to the OFF position
Signed-off-by: Adam Ford <aford173@gmail.com>
The previous e-mail pointing to Vaibhav Hiremath <hvaibhav@ti.com>
is bouncing and has for some time. This updates it to myself and I
work for Logic PD the manufacturer of the AM3517-SOM and EVM
Signed-off-by: Adam Ford <aford173@gmail.com>
Currently the U-Boot project contains 2 documentation directories:
- doc/
- Documentation/
The Documentation directory only contains device tree bindings related
content, so move the 3 files to doc/device-tree-bindings/.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
There is no reason not to use macros which are already defined.
It is also much easier for grepping.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Header file "asm/utils.h" is not required to compile "spl_ymodem.c".
So, removing this dependency allows other architectures to use this
booting device as "asm/utils.h" is only present in "arm" architecture.
Signed-off-by: Paulo Zaneti <paulo.zaneti@datacom.ind.br>
The length returned by hexport_r has a few redundant characters.
This appears as NULL characters at the end so seems harmless.
Remove the surplus counts in two places
totlen += strlen(ep->key) + 2;
I'm guessing the +2 here is for = and sep char. But there is another
totlen += 2; line that does that.
size = totletn + 1;
Doesn't make sense and isn't justified with any comment.
Signed-off-by: Zubair Lutfullah Kakakhel <zubair@resin.io>
Use blk_dread()/blk_dwrite() in mmc_read()/mmc_write() AVB operation
implementations. This fixes compilation issues when CONFIG_BLK is
enabled.
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
1. Since libavb library alone is highly portable, introduce dedicated
Kconfig symbol for AVB bootloader-dependent operations, so it's possible
to build libavb separately. AVB bootloader-dependent operations include:
* Helpers to process strings in order to build OS bootargs.
* Helpers to access MMC, similar to drivers/fastboot/fb_mmc.c.
* Helpers to alloc/init/free avb ops.
2. Add CONFIG_FASTBOOT dependency, as fastboot buffer is
re-used in partition verification operations.
Reported-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
In the case that there was no name defined for a partition the
code assumes that name_len is 22 and therefore allocates exactly
that space for a dummy name. But the function sprintf() first
resolves "0x%08llx@0x%08llx" to a string that is longer than 22
bytes. This leads to a buffer overflow. The replacement function
snprintf() limits the copied bytes to name_len and therefore
avoids the buffer overflow.
Signed-off-by: Kay Potthoff <Kay.Potthoff@microsys.de>
With recent kernel v4.18-rcx, uImage becomes bigger than 8MB.
Set SYS_BOOTM_LEN to 16MB, this fix the following error message:
"Fix Loading Kernel Image ... Image too large: increase
CONFIG_SYS_BOOTM_LEN"
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
A comment in the kernel doc of the mtd_oob_ops structure tells that it
is not possible to write more than one page with OOB. This was
probably true at some time in the past but today it is entirely wrong.
As one can see for instance in the nand_do_write_ops() helper available
in the NAND core, this implementation called by mtd->_write_oob()
simply loops over the pages until everything has been written.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
rtc_to_tm() and rtc_mktime() are required for some RTC drivers, at least
PL031. Without this patch, we also need to enable CONFIG_CMD_DATE even if
we don't want or need this command.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Our nand_ecc_modes_t is already a bit abused by value NAND_ECC_SOFT_BCH.
This enum should store ECC mode only and putting algorithm details there
is a bad idea. It would result in too many values impossible to support
in a sane way.
To solve this problem let's add a new enum. We'll have to modify all
drivers to set it properly but once it's done it'll be possible to drop
NAND_ECC_SOFT_BCH. That will result in a cleaner design and more
possibilities like setting ECC algorithm for hardware ECC mode.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: b0fcd8ab7b3c89b5da7fff5224d06ed73e7a33cc]
[Philippe Reynes: adapt code to u-boot]
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Only the MUSB driver is currently supported on the omap3_logic
boards. The driver is using the new-musb and not the legacy
version, so this patch removes the dead code references.
Signed-off-by: Adam Ford <aford173@gmail.com>
In order to use the device tree for MMC, the card-detect pin
needs to be inverted. This patch places this into the
am3517-evm-u-boot.dtsi file to keep the main DTS and DTSI files
clean and in-sync with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
With the resync of the omap3.dtsi file, the reg-shift was removed
so it breaks the UART. Adding the reg-shift into the
am3517-evm-u-boot.dtsi keeps the reg-shift for U-Boot, but keeps
the dts/dtsi files clean from Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
The Linux kernel moved to sphinx-based documentation and got rid of the
DocBook based documentation quite a while ago. Hence, the DocBook
documentation for U-Boot should be converted as well.
To achieve this, import the necessary files from Linux v4.17, and
convert the current DocBook documentation (three files altogether) to
sphinx/reStructuredText.
For now, all old DocBook documentation was merged into a single
handbook, tentatively named "U-Boot Hacker Manual".
For some source files, the documentation style was changed to comply
with kernel-doc; no functional changes were applied.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
There have been some significant changes to the DM37 SOM-LV device
tree. This patch re-syncs it with Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
There have been some refactoring of the DTS files for the Logic PD
DM37 Torpedo. This patch re-sync's the DTS files with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
There have been several minor changes to the OMAP3.dtsi, so this
patch re-syncs it with Linux. An addition include/dt-binding was
also brought with it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Several changes have been made to the AM3517-evm and the underlying
am3517.dtsi file. This patch re-sync's the DTS and DTSI files with
Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
The m5253evbe board has been marked as orphan since June of 2014 and
should have been dropped a while ago. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Assigning a parameter which is not used afterwards has not effect.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are already definitions for ramdisk_addr_r and fdt_addr_r, so
having a duplicate copy called ramdiskaddr and fdtaddr is confusing.
This patch converts any references to ramdisk_addr_r and fdt_addr_r
and removes the duplicates.
Signed-off-by: Adam Ford <aford173@gmail.com>
The USBOH module on imx25 chips contains two USB controllers which are
called USB OTG Controller and USB Host Controller. Each one has its EHCI
root hub. The OTG Controller's EHCI registers start at offset 0, the Host
Controller's registers start at offset 0x400.
We set CONFIG_MXC_USB_PORT=0 to select the OTG Controller and 1 for the
Host Controller. Therefore, IMX_USB_PORT_OFFSET must be 0x400. Using
this setting, the Host Controller starts working on my imx25 board.
Please note that the imx25 reference manual claims that the Host
Controller's registers start at 0x200. This is not correct. The Linux
Kernel uses the correct offset 0x400 in imx25.dtsi.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signing parts of a u-boot imximage for image verification in High
Assurance Boot (HAB) in a post-build process, requires some
information from the imximage header. Currently, this information is
only provided during the image build, which makes the transfer of this
information to the post-build process harder than necessary.
The i.MX HAB information (start and length) can be calculated either
by using information from the image-configuration file, or from the
information in the flash header of the imximage.
The advantage of using information from flash header is, that they are
not only available during image creation, but also available if
existing images are processed.
Example:
$ tools/mkimage -l u-boot.imx
Image Type: Freescale IMX Boot Image
Image Ver: 2 (i.MX53/6/7 compatible)
Mode: DCD
Data Size: 483328 Bytes = 472.00 KiB = 0.46 MiB
Load Address: 877ff420
Entry Point: 87800000
HAB Blocks: 0x877ff400 0x00000000 0x00071c00
DCD Blocks: 0x00910000 0x0000002c 0x00000208
Signed-off-by: Holger Dengler <dengler@linutronix.de>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
In preparation for delivery bottlenecks, enable support for GigaDevice, Macronix, and Winbond nor flash chips.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Since the vast majority of i.MX6 boards are migrating to SPL,
this patch converts im6q_logic to SPL and enables the SDP for
loading SPL and u-boot.img over USB. The Falcon mode only
supports NAND flash as of now due to limited space/RAM, but
all i.MX6D/Q SOM's from Logic PD have internal NAND from which
to boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
This reverts commit a637fe6f27.
The DDR DRAM calibration was enhanced by write leveling correction code.
It can be used with T-topology now.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>