Commit Graph

20688 Commits

Author SHA1 Message Date
Michael Trimarchi
b0857c45c1 usb: omap: ulpi: fix ulpi transceiver access
This patch fix the omap access to the transceiver
configuration registers using the ulpi bus. As reported by
the documentation the bit31 is used only to check if the
transaction is done or still running and the reading and
writing operation have different offset and have different
values. What we need to do at the end of a transaction is
leave the bus in done state. Anyway an error using the ulpi
omap register is not recoverable so any error give out the
usage of this interface.

Tested on a custom OMAP5430 board with a TUSB1210 ULPI PHY
on USBB1.

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-07-02 09:21:15 -04:00
Albert ARIBAUD
e6c7f86f03 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-06-28 17:51:13 +02:00
Otavio Salvador
d6c6d127c5 vf610twr: Remove SoC name from U-Boot prompt
We've been dropping SoC name from U-Boot prompt as it increase
complexity for automatic testing and makes line longer for no good
reason.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Andy Voltz <andy.voltz@timesys.com>
2013-06-28 16:59:08 +02:00
Otavio Salvador
ca21f61e28 vf610twr: Add default environment in line with other Freescale boards
This adds a default environment which should be able to support both
3.0.15 from Timesys and upcoming 3.11.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Andy Voltz <andy.voltz@timesys.com>
2013-06-28 16:58:50 +02:00
Fabio Estevam
620ca1c174 video: mxsfb: Break the line in videomode message
Currently we have the following on boot:

CPU:   Freescale i.MX28 rev1.2 at 454 MHz
BOOT:  SSP SD/MMC #0, 3V3
DRAM:  128 MiB
MMC:   MXS MMC: 0
Video: MXSFB: 'videomode' variable not set!In:    serial

Break the line of the warning message in order to have a better reading format.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-28 16:54:47 +02:00
Fabio Estevam
fca42cd659 MAINTAINERS: Add an entry to the mx6q wandboard variant
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2013-06-28 16:52:03 +02:00
Fabio Estevam
5307188889 m28evk: Move README file inside board directory
Board specific READMEs should be located inside the respective board directory.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-26 17:41:06 +02:00
Fabio Estevam
17f3f36652 mx28evk: Move README file inside board directory
Board specific READMEs should be located inside the respective board directory.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-26 17:40:39 +02:00
Fabio Estevam
54965b6136 README: mxs: Introduce README.mxs
Create a README.mxs file that contains instructions on how to use U-boot for
both MX23 and MX28.

As boot from NAND has only been tested on mx28, make it clear that it only
applies to MX28.

While at it, do some small cleanups for the sake of consistency:
- Use "MX28" instead of "i.MX28"
- Use "section" instead of "chapter" when referring to specific parts of the
reference manual chapters.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-26 17:39:57 +02:00
Fabio Estevam
7333eca5f4 README: mx28_common: Fix structure of sentence
Re-structure the sentence a bit so that it can clearer.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-26 17:34:22 +02:00
Fabio Estevam
3f5e2e2a7d README: mx28_common: Do not hardcode the SSP port
MX28 can boot from SSP0 or SSP1, so it is better not to hardcode the SSP port
in the instructions.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-26 17:34:22 +02:00
Fabio Estevam
84286c22e6 README: mx28_common: Keep the text within 80 columns
In order to improve readability keep the text within 80 columns.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-26 17:34:22 +02:00
Robert Winkler
262326b4c3 imx: nitrogen6x: Enable filesystem generic commands
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
2013-06-26 17:34:22 +02:00
Robert Winkler
3655829511 imx: nitrogen6x: Enable raw initrd
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
2013-06-26 17:34:21 +02:00
Robert Winkler
9b9ba6f035 imx: nitrogen6x: Enable bootz
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
2013-06-26 17:34:21 +02:00
Robert Winkler
87de2d64db imx: nitrogen6x: Enabled data cache
Signed-off-by: Robert Winkler <robert.winkler@boundarydevices.com>
2013-06-26 17:34:21 +02:00
trem
79713f0ad8 mx27: add i2c clock
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
2013-06-26 17:34:21 +02:00
trem
6247c4653b mx27: add function enable_caches
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
2013-06-26 17:34:21 +02:00
Pierre Aubert
c174797061 imx: Add support for the SabreSD shipped with i.MX6DL
The SabreSD platform is available with i.MX6Q or i.MX6DL. This patch adds the
support of the i.MX6DL. The config file and the board directory are renamed
to remove the reference to the MX6Q.

Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-06-26 17:34:11 +02:00
Pierre Aubert
87d720e0c2 imx: Complete the pin definitions for the i.MX6DL / i.MX6Solo
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
2013-06-26 16:47:30 +02:00
Pierre Aubert
7aa1e8bb1b imx6: fix GPR2 wrong definition
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
2013-06-26 16:28:54 +02:00
Eric Nelson
2dbe64ca24 dwc_ahsata: Allow use with dcache enabled
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-06-26 16:26:45 +02:00
Dirk Behme
9a30903b44 spi: mxc_spi: Update pre and post divider algorithm
The spi clock divisor is of the form x * (2**y),  or  x  << y, where x is
1 to 16, and y is 0 to 15. Note the similarity with floating point numbers.
Convert the desired divisor to the smallest number which is >= desired divisor,
and can be represented in this form. The previous algorithm chose a divisor
which could be almost twice as large as needed.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
2013-06-26 16:23:30 +02:00
Dirk Behme
8d4c4ffb95 spi: mxc_spi: Fix pre and post divider calculation
Fix two issues with the calculation of pre_div and post_div:

1. pre_div: While the calculation of pre_div looks correct, to set the
CONREG[15-12] bits pre_div needs to be decremented by 1:

The i.MX 6Dual/6Quad Applications Processor Reference Manual (IMX6DQRM
Rev. 0, 11/2012) states:

CONREG[15-12]: PRE_DIVIDER
0000 Divide by 1
0001 Divide by 2
0010 Divide by 3
...
1101 Divide by 14
1110 Divide by 15
1111 Divide by 16

I.e. if we want to divide by 2, we have to write 1 to CONREG[15-12].

2. In case the post divider becomes necessary, pre_div will be divided by
16. So set pre_div to 16, too. And not 15.

Both issues above are tested using the following examples:

clk_src = 60000000 (60MHz, default i.MX6 ECSPI clock)

a) max_hz == 23000000 (23MHz, max i.MX6 ECSPI read clock)

-> pre_div =  3 (divide by 3 => CONREG[15-12] == 2)
-> post_div = 0 (divide by 1 => CONREG[11- 8] == 0)
               => 60MHz / 3 = 20MHz SPI clock

b) max_hz == 2000000 (2MHz)

-> pre_div =  16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 1  (divide by  2 => CONREG[11- 8] == 1)
               => 60MHz / 32 = 1.875MHz SPI clock

c) max_hz == 1000000 (1MHz)

-> pre_div =  16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 2  (divide by  4 => CONREG[11- 8] == 2)
               => 60MHz / 64 = 937.5kHz SPI clock

d) max_hz == 500000 (500kHz)

-> pre_div =  16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 3  (divide by  8 => CONREG[11- 8] == 3)
               => 60MHz / 128 = 468.75kHz SPI clock

Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
2013-06-26 16:22:51 +02:00
Tapani Utriainen
491f2947a1 Add support for Wandboard Quad
Add support for the Quad version of Wandboard; fix compile warning resulting
from having 2G of memory.

Signed-off-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-06-26 16:14:32 +02:00
Mike Dunn
9dc8fef258 pxa: fix memory coherency problem after relocation
On the xscale, the icache must be invalidated and the write buffers drained
after writing code over the data bus, even if the caches are disabled.  Tested
on the pxa270.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-06-22 15:25:28 +02:00
Mike Dunn
84c617beb2 pxa: use -mcpu=xscale compiler option
Pass '-mcpu=xscale' to the compiler instead of march and mtune.  This will cause
gcc to define the __XSCALE__ macro.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-06-22 15:25:28 +02:00
Mike Dunn
097d86d098 pxa: turn icache off in cpu_init_crit()
The comment in the low-level initialization function cpu_init_crit() says that
the caches are being disabled, but (oddly) the icache is actually turned on.
This is probably not a good idea prior to relocating code, so this patch turns
it off.  Tested on the pxa270.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-06-22 15:25:28 +02:00
Mike Dunn
3497d43215 pxa: palmtreo680 flash programming utility
This adds a userspace linux utility that writes the u-boot image to an mtd
partition on the docg4 nand flash.

A special utility is required to do this because u-boot is partially loaded by
an initial program loader (IPL) that is permanently programmed to the boot
region of the flash.  This IPL expects the image to be written in a unique
format. The characteristics of this format can be summarized as follows:
  - Flash blocks to be loaded must have a magic number in the oob bytes of the
    first page of the block.
  - Each page must be written redundantly in the subsequent page.
  - The integrated flash controller's "reliable mode" is used, requiring that
    alternate 2k regions (4 pages) are skipped when writing.
For these reasons, a u-boot image can not be written using nandwrite from
mtd-utils.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-06-22 15:25:28 +02:00
Mike Dunn
0dc0e846f3 pxa: add support for palmtreo680 board
This patch adds support for the Palm Treo 680 smartphone.  A quick overview of
u-boot implementation on the treo 680...

The treo 680 has a Diskonchip G4 nand flash chip.  This device has a 2k region
that maps to the system bus at the reset vector in a NOR-like fashion so that it
can be used as the boot device.  The phone is shipped with this 2k region
configured as write-protected (can't be modified) and programmed with an initial
program loader (IPL).  At power-up, this IPL loads the contents of two flash
blocks to SDRAM and jumps to it.  The capacity of the two blocks is not large
enough to hold all of u-boot, so a u-boot SPL is used.  To conserve flash space,
these two blocks and the necessary number of subsequent blocks are programmed
with a concatenated spl + u-boot image.  That way, the IPL will also load a
portion of u-boot proper, and when the spl runs, it relocates the portion of
u-boot that the IPL has already loaded, and then resumes loading the remaining
part of u-boot before jumping to it.

The default_environment is used (CONFIG_ENV_IS_NOWHERE) because I didn't think
that having a writable environment was worth the cost of a flash block, although
adding it would be straightforward.  I abuse the CONFIG_EXTRA_ENV_SETTINGS
option to specify the usbtty for the console (CONFIG_SYS_CONSOLE_IS_IN_ENV).

Support for the LCD is included, but currently it is only useful for displaying
the u-boot splash screen.  But if u-boot is built without the usbtty console, it
does display the auto-boot progress nicely.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-06-22 15:25:28 +02:00
Albert ARIBAUD
fbf87b1823 arm: optimize relocate_code routine
Use section symbols directly
Drop support for R_ARM_ABS32 record types
Eliminate unneeded intermediate registers
Optimize relocation table iteration

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 23:05:50 +02:00
Albert ARIBAUD
47bd65ef05 arm: make __rel_dyn_{start, end} compiler-generated
This change is only done where needed: some linker
scripts may contain relocation symbols yet remain
unchanged.

__rel_dyn_start and __rel_dyn_end each requires
its own output section; putting them in relocation
sections changes their flags and breaks relocation.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 23:05:29 +02:00
Albert ARIBAUD
d026dec875 arm: make __image_copy_{start, end} compiler-generated
This change is only done where needed: some linker
scripts may contain __image_copy_{start,end} yet
remain unchanged.

Also, __image_copy_end needs its own section; putting
it in relocation sections changes their flags and makes
relocation break.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 23:05:05 +02:00
Albert ARIBAUD
df84502edf arm: generalize lib/bss.c into lib/sections.c
File arch/arm/lib/bss.c was initially defined for BSS only,
but is now going to also contain definitions for other
section-boundary-related symbols, so rename it for better
accuracy.

Also, remove useless 'used' attributes.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 23:04:43 +02:00
Albert ARIBAUD
09d81184e1 remove all references to .dynsym
Discard all .dynsym sections from linker scripts
Remove all __dynsym_start definitions from linker scripts
Remove all __dynsym_start references from the codebase

Note: this touches include/asm-generic/sections.h, which
is not ARM-specific, but actual uses of __dynsym_start
are only in ARM, so this patch can safely go through
the ARM repository.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 23:04:05 +02:00
Albert ARIBAUD
c37980c31a arm: ensure u-boot only uses relative relocations
Add a Makefile target ('checkarmreloc') which
fails if the ELF binary contains relocation records
of types other than R_ARM_RELATIVE.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-21 22:59:20 +02:00
Simon Guinot
7737c99460 net2big_v2: initialize LEDs at startup
This patch allows to configure the net2big_v2 LEDs at startup (through
the GPIO extension bus). The front blue LED is enabled and the SATA rear
LEDs are configured to blink in relation with the SATA activity.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2013-06-20 14:01:23 +05:30
Simon Guinot
d5cc3f5241 LaCie/common: add support for the CPLD GPIO bus
This patch adds support for the CPLD GPIO bus found on some LaCie boards
(as the 2Big/5Big Network v2 and the 2Big NAS). This parallel GPIO bus
exposes two registers (address and data). Each of this register is made
up of several dedicated GPIOs. An extra GPIO is used to notify the CPLD
that the registers have been updated.

Mostly this bus is used to configure the LEDs on LaCie boards.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
2013-06-20 14:01:23 +05:30
Simon Guinot
2af4d0f49f net2big_v2: initialize I2C fan at startup
This patch ensures minimal cooling for the net2big_v2 by automatically
starting the I2C fan (GMT G762) at low speed (2800 RPM).

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2013-06-20 14:01:23 +05:30
Albert ARIBAUD
c2543a21df Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2013-06-19 23:58:01 +02:00
Albert ARIBAUD
69f14dc2fd Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'
Conflicts:
	spl/Makefile
2013-06-19 12:53:59 +02:00
Dan Murphy
bf3b98a188 arm: omap4: panda: Fix checkpatch on panda file
Fix the checkpatch warning on the panda.c file for leading
spaces.
Fix the CHECK warnings on the panda.c file for parenthesis alignment.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-06-18 10:43:30 -04:00
Dan Murphy
7d47d1caa0 arm: omap4: panda: Add reading of the board revision
Detect if we are running on a panda revision A1-A6,
or an ES panda board. This can be done by reading
the level of GPIOs and checking the processor revisions.
This should result in:
Panda 4430:
     GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
     GPIO171, GPIO101, GPIO182: 1 0 1 => A6
Panda ES:
     GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
     GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3

Set the board name appropriately for the board revision that
is detected.

Update the findfdt macro to load the a4 device tree binary.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
[trini: %s/CONTROL_PADCONF_CORE/(*ctrl)->control_padconf_core_base/ and
 formatting for that]
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-18 10:43:30 -04:00
Dan Murphy
45dbbf29bb arm: dra7xx: Update the EXTRA_ENV_SETTINGS
Update the EXTRA_ENV_SETTING for the dra7xx.
The console needs to be set to ttyO0 and the
findfdt needs to be updated to load the
dra7xx-evm.dtb file.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-06-18 10:43:29 -04:00
Dan Murphy
3de7c28c29 arm: omap5_uevm: Correct the console sys prompt for 5432
Correct the console sys prompt to display the correct processor
and the corrent board

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reported-by: Lubomir Popov <lpopov@mm-sol.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-06-18 10:43:29 -04:00
Dan Murphy
a71432151f arm: omap: Add check for fdtfile in the findfdt macro
In the omap4, omap5 and am335x common files add a check to ensure that the fdtfile is
defined after the findfdt macro has run.  If the file is not defined then warn the user that the
dtb file is not defined.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-06-18 10:43:29 -04:00
Heiko Schocher
7ea7f689ca arm, am33xx: move uart soft reset code to common place
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-18 10:40:06 -04:00
Heiko Schocher
7b9c5d0bfd arm, am335x: make mpu pll config configurable
upcoming support for siemens boards switches mpu pll clk in board
code. So make this configurable.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-06-18 09:18:46 -04:00
Heiko Schocher
49f7836500 arm, am33xx: move rtc32k_enable() to common place
move rtc32k_enable() to common place so all am33xx boards can use it.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-06-18 09:12:38 -04:00
Rajeshwari Shinde
ed7bdc03eb MMC: DWMMC: Fix FIFO_DEPTH calculation
Current DWMMC driver used to give FIFO underrun/overrun error every 3rd time
for mmc rescan command.
In current code FIFO_DEPTH is getting calculated after reading the default FIFOTH
register and extracting the RX_WMARK bits from it i.e (RX_WMARK = FIFO_DEPTH/2 -1).
Instead of storing the correct value, we were recalculating the FIFO_DEPT each
time which is not correct.

Based on "[PATCH V9 3/9] DWMMC: Initialise dwmci and resolve EMMC read write issues"
http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/160247

Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2013-06-17 11:03:42 +09:00