The CPLD node is missing in Linux 4.17 DTs on H3/M3W ULCB, pull the
node into U-Boot specific DT until it hits mainline Linux, to make
syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The AVB node is not complete in Linux 4.17 DTs on V3M Eagle, pull the
AVB node extras into U-Boot specific DT until they hit mainline Linux,
to make syncing of DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The SDHI nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The USB nodes are not in Linux 4.17 DTs in M3N, pull them into U-Boot
specific DT extras until they hit mainline Linux, to make syncing of
DTs easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
The RPC DT bindings are still work in progress. Extract the RPC DT node
from the DT to allow easier update and so it can be replaced once the DT
bindings are stable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
Add label to the /soc node, so it can be referenced from the U-Boot DTs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
V2: Rebase on u-boot/master
Use DM for both MMC and USB subsystems and use dedicated DTS
for U-Boot configuration.
Disable SPL support for GPIO and remove EVMSK leftover for
DDR power control via GPIO.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch modifies the meson clock driver to use syscon/regmap like
the Linux kernel does, as it is needed if we want to share the same
DTS files.
DTS files are synchronized from Linux 4.19.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Enable the HS400 support in DT on H3, M3W, M3N Salvator-X(S)
and ULCB boards as well as E3 Ebisu board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add regulators and pinmuxes for SDHI0 and SDHI1 SD and microSD
slots on E3 Ebisu and mark them as capable of up to SDR104 mode
of operation. With the SDHI fixes in place, it is now possible
to use SDR104.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable SDR104 modes on M3W and H3 boards. With the SDHI fixes
in place, it is now possible to use SDR104.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add pinmux entry for the eMMC DS line, as it is connected on these boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds the definitions need to use the USB OTG in rv1108
board. This has been tested using USB Mass Storage to export and
program a eMMC device.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds the pinctrl handles to enable the use of eMMC on custom
boards (as minievk) and makes it easier for later addition.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Some SanDisk Ultra cards trigger intermittent errors on detection
resulting in an -EOPNOTSUPP, when running at 50MHz.
Waveform analysis suggest that the level shifters that are used on the
RK3399-Q7 module (for voltage translation between the on-module
voltages and the 3.3V required on the card-edge) don't handle clock
rates at or above 48MHz properly. This change reduces the maximum
frequency on the external SD-interface to 40MHz (for a safety margin
of 20%).
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
- Some Kirkwood boards converted to DM_SPI by Chris
- New Armada-385 SoC revision printed by Chris
- Ethernet enable on mcbin by Baruch
- Support 2 DRAM banks on Armada-8k boards by Baruch
This configuration is useful when you want to run small u-boot and
perform DDR memory test to make sure that DDR is properly configured.
It is use for board bringup because alternative u-boot memory tests is
quite good.
Configuration is running out of OCM.
As is done for others mini configurations 0x80 bytes for variables is
enough and only default variables are stored there.
Alternative memtest is enabled and also 2GB of DDR via DTS files.
Configuration is enabling ZYNQMP_PSU_INIT_ENABLED and include psu_init()
from zcu102 for testing purpose.
In case of size issue this can be moved to SPL configuration as is done
for mini_qspi configuration but it is not a problem now.
Log:
U-Boot 2018.11-00268-gbd58b8ba8915 (Nov 29 2018 - 15:33:35 +0100)
Model: ZynqMP MINI
Board: Xilinx ZynqMP
DRAM: WARNING: Initializing TCM overwrites TCM content
2 GiB
EL Level: EL3
In: dcc
Out: dcc
Err: dcc
ZynqMP>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This fixes the board's dts to supply SPL with QSPI info.
The EBV Socrates board has DIP switches to boot from SD card or
QSPI, so let's fix its defconfig to work for both cases.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add -u-boot.dtsi files to keep the current U-Boot behaviour:
- add u-boot,dm-pre-reloc where required
- disable watchdog
- set uart clock frequency
- add gpio bank-name properties
where appropriate:
- make qspi work (add alias for spi0, fix compatible for flash)
- enable usb (status okay, add alias for udc0)
Adapt board dts files that are not in Linux to keep their old
behaviour.
Change licenses to SPDX.
(Patman warnings/errors are in 1:1 copied files from Linux)
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
If there are more instances of si570 clock-output-names property
should be used for differentiation of clock output.
The patch is adding this optional properties for all zynqmp boards with
si570 chip.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This chip is on the board but handling should be done via firmware not
via Linux driver. Changing status property to keep it in the tree to
describe it instead of removing this node completely.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable reading tx and rx buswidth from DT via spi-uclass.
To get these from uclass spi-flash compatible string has to be added
to flash node.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DC4 board has qspi on it hence define and enable
qspi node for it.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds device tree for MT7623 development board - Bananapi R2
Detailed hardware information for BPI-R2 which could be found on
http://wiki.banana-pi.org/Banana_Pi_BPI-R2.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds MT7629 device tree and the includes it needs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add that node path in u-boot overlay dtsi file for now to keep
am335x-chiliboard.dts in sync with Linux.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import chiliSOM and chiliboard dts files from Linux v4.19. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Synchronize the Amlogic AXG Device Tree files and bindings include from
the recent Linux 4.20-rc1, because it includes patches fixing support for
U-boot.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Make sense to add controller ID to model name to have it visible through
the logs to know which controller is used by which configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
spi-rx-bus-width property is part of flash, so it should be moved
to flash node from qspi node. This patch fixes the incorrect read
of spi-rx-bus-width property by moving it to flash node.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SolidRun Clearfog GT-8K is based on Armada 8040.
https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k
The config file is identical to the Macchiatobin one
(mvebu_mcbin-88f8040_defconfig) with only the default device-tree
changed.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Sync the k3-am654 specific dts files from Linux next with tag
20181019. This changes are in queue for Linux v4.20-rc1
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some minor changes have been made to the AM3517-evm and the underlying
am3517.dtsi files. This patch re-sync's the DTS and DTSI files with
Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
This add the initial support of the broadcom reference
board bcm968580xref with a bcm6858 SoC.
This board has 512 MB of ram, 256 MB of flash (nand),
2 usb port, 1 uart, 4 ethernet ports (LAN), 1 ethernet port (WAN).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This add the initial support of the broadcom bcm6858 SoC family,
only the cpu, dram and uart are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
OrangePi Lite2 is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- AP6356S Wifi/BT
- USB 2.0, USB 3.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Based on the information from hardware schematics and orangepi
vendor orangepi H6 boards, One Plus and Lite2 shares common nodes
like axp805, uart, mmc0 etc. The common differences between them is
- One Plus, has Ethernet
- Lite2, has Wifi, USB3, CSI port.
So, add common orangepi nodes into sun50i-h6-orangepi.dtsi so-that
it case use on respective orangepi h6 board dts files.
Cc: zhaoyifan <zhao_steven@263.net>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Pinebook is a laptop produced by Pine64, with USB-connected keyboard,
USB-connected touchpad and an eDP LCD panel connected via a RGB-eDP
bridge from Analogix.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Pine64 LTS is an updated version of the Pine64, copying the
technical updates from the SoPine platform: LPDDR3 DRAM, eMMC socket and
soldered SPI flash chip, even the broken SD card detect pin has been copied.
Consequently this leads to the .dts (copied from the kernel) just including
the SoPine baseboard .dts, and the defconfig being almost identical.
Nevertheless the boards deserves a separate config.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update the .dts/.dtsi files from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date: Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sun50i-a64.dtsi changes introduced in Linux v4.19-rc1 changed the
compatible name for the syscon controller, dropping the generic "syscon"
fallback. Using this new DT node will make the Ethernet driver in every
older kernel (or non-Linux kernels) fail to initialise the MAC device.
To allow booting distribution kernels (from installer images via UEFI,
for instance), re-add the syscon compatible string as a fallback. This
works with both older and newer kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update the .dts/.dtsi file from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date: Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The new board version has the 2nd FPGA connected via CS# 0 instead of
2 on SPI bus 1. Change this setup in the DT accordingly. Please note
that this change does still work on the old board version because the
CS signal is not used on this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Add the "spi-flash" compatible string so that the generic sf_probe
driver can probe the SPI flash on the theadorable Armada-XP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 3c28576bb0 ("arm: dts: imx8qxp: fix build warining")
fixed the dts warning by removing the unnecessary
#address-cells/#size-cells, but the recommendation for regulators is not
to place them under "simple-bus", so move the reg_usdhc2_vmmc regulator
accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This is a large update of the AST2500 SoC DTS file bringing it to the
level of commit 927c2fc2db19 :
Author: Joel Stanley <joel@jms.id.au>
Date: Sat Jun 2 01:18:53 2018 -0700
ARM: dts: aspeed: Fix hwrng register address
There are some differences on the compatibility property names. scu,
reset and clock drivers are also different.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Banana Pi M2 Zero is a board by Sinovoip with Allwinner H2+ SoC, 16-bit
512MiB DDR3 memory, a MicroSD slot, two MicroUSB ports (one OTG and one
powering-only) and a miniHDMI port.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[jagan: Fixed board MAINTAINERS file]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Introduce dtsi for i.MX8QXP, since there is other variants i.MX8DX(P),
so add them there, because i.MX8QXP includes the dtsi of them.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Build the -u-boot variants of the device trees so they can be included
in Multi-DTB fitImage, which in turn allows us to build single U-Boot
image for multiple boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Xilinx DLC20 has I2C0 with EEPROM(1KB), UART1, GPIO, SD0 (EMMC 4GB),
USB0 device, ENET0, QSPI (16MB) and DDR(two of 256MB each).
Boards have mix of Winbond/ST QSPIs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds Device Tree for the Khadas VIM2 board.
The meson-gxm-khadas-vim2.dts is synchronized from Linux 4.18.10.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Commit 9faa43c4b5 ("ARM: dts: i.MX6UL: U-Boot specific dts for u-boot,
dm-spl") removes the u-boot,dm-spl properties from the imx6ul.dtsi file
and breaks the OPOS6UL board.
Add the u-boot,dm-spl properties into *-u-boot.dts files to make the
board boot again.
Fixes: commit 9faa43c4b5 ("ARM: dts: i.MX6UL: U-Boot specific dts for u-boot, dm-spl")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The CPLD is used to reset the ULCB and it was removed
during DT sync with Linux 4.17. Reinstate it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Sync with 14e21cb8f811 ("arm64: dt: hikey: Add optee node"
from Linux kernel.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
With the device trees doing most of the work of pin-muxing and
DM doing much of the peripheral initialization, this creates
new defconfig files for each of the Logic PD variants with
proper register settings/pin-muxing.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
The baseboards and SOM's are virtually identical to their DM37
counterparts, but OMAP36/37 and OMAP3 have some minor register
differences. With the boards being mostly driven by device trees
now, this synchronizes their respective device trees with linux-omap
for-next branch destined for 4.20 (or whatever the version after 4.19
will be called)
Signed-off-by: Adam Ford <aford173@gmail.com>
With the introduction of the omap serial driver, the need for some
of these U-Boot specific modifications is gone. This cleans up
this unnneeded stuff.
Signed-off-by: Adam Ford <aford173@gmail.com>
The device tree entries are from linux-omap's for-next branch
destined to me put into 4.20 (or whatever the version is after 4.19)
Signed-off-by: Adam Ford <aford173@gmail.com>
The I2C6 is used to communicate with the PMIC and it was removed
during DT sync with Linux 4.17. Reinstate it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.
The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
[picked from the identical linux patch
https://patchwork.kernel.org/patch/10609253/]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dwmmc controllers on rk3188 do not have idma support, so need to
use the fifo-mode and it my tests they became confused and stopped
working if the frequency was to high.
While I only tested in somewhat bigger steps, 32MHz for example
hung the controller, while reducing it to 16MHz worked just fine
and is reasonably fast to load a kernel from mmc.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XRFI
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
With the omap_mmc driver no longer supporting cd-inverted, this
patch removes all these references since they are not needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 5d9ef839f874f4e3923c8a9ae7b136c6c3912cd5
Author: Stefan Mavrodiev <stefan@olimex.com>
Date: Wed May 16 14:38:08 2018 +0300
ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board
Note:
- Update sun7i-a20-primo73.dts as per Linux, since
this dts is U-Boot specific.
- Drop sun7i-a20-olimex-som-evb-emmc.dts since no board
added for this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update all A10s/A13/gr8/r8devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commit:
commit 190e3138f9577885691540dca59c2f07540bde04
Merge: cafc87023b0d a7affb13b271
Author: Arnd Bergmann <arnd@arndb.de>
Date: Tue Mar 27 14:58:00 2018 +0200
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 590b0c0cfc6162aeebbf43eaafb9753b56df1532
Author: Pascal Roeleven <dev@pascalroeleven.nl>
Date: Fri Apr 20 12:21:12 2018 +0200
ARM: dts: sun4i: Fix incorrect clocks for displays
Note: Update pinctrl-0 for sun4i-a10-inet-3f.dts, sun4i-a10-inet-3w.dts
like other dts file since there dts file are U-Boot specific.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
