Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and child nodes to enable driver binding to mxsfb device.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
- some fix for rk3399-puma;
- rockchip script make_fit_atf.py cleanup
- Enable TPL for rk3399 orangepi and nanopi4;
- add support for rk3399 boards: Nanopi NEO4, Rockpro64, Rock PI 4;
When using External PHY, reset the mux to use the external PHY in case U-Boot
was chainloaded from a misconfigured bootloader.
Fixes: 33e3378091 ("ARM: meson: rework soc arch file to prepare for new SoC")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The following DT nodes in the process on review for Linux 5.3,
until Linux 5.3 is tagged, add the missing DT nodes in u-boot specific
DTSI files that will be dropped when the v5.3-rc1 DT is synced again.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add initial support for Rock PI 4 board.
Specification
- Rockchip RK3399
- LPDDR4
- eMMC
- SD card slot
- RTL8211E 1Gbps
- HDMI In/Out, DP, MIPI DSI/CSI
- PCIe M.2
- USB 2.0, USB-3.0
- USB C Type
Commit details of rk3399-rock-pi-4.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: add ROCK Pi 4 DTS support"
(sha1: 1b5715c602fda7b812af0e190eddcce2812e5417)
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add initial support for Rockpro64 board.
Specification
- Rockchip RK3399
- 2/4GB Dual-Channel LPDDR3
- SD card slot
- eMMC socket
- 128Mb SPI Flash
- Gigabit ethernet
- PCIe 4X slot
- WiFI/BT module socket
- HDMI In/Out, DP, MIPI DSI/CSI, eDP
- USB 3.0, 2.0
- USB Type C power and data
- GPIO expansion ports
- DC 12V/2A
Commit details of rk3399-rockpro64.dts sync from Linux 5.1-rc2:
"arm64: dts: rockchip: rockpro64 dts add usb regulator"
(sha1: 6db644c79c8d45d73b56bc389aebd85fc3679beb)
'Akash' has sent an initial patch before, so I keep him as board
maintainer and I'm co-maintainer based on our conversation.
Signed-off-by: Akash Gajjar <akash@openedev.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch cleans up make_fit_atf.py in the following way:
* Fix all issues reported by pylint
* Move copyright notice from file-to-generate to script
* Fix of-by-one bugs in loadables property
* Remove commented-out (dead) code.
Besides the bugfix no intended changes.
Tested on RK3399-Q7 with TF-A v2.1 as BL31.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK3399 SPL does not use a pinctrl driver to setup the UART pins.
Instead it works based on config macros, which set the base address
of the actual UART block.
Currently the RK3399 SPL support UART0 and UART2.
This patch adds UART3 in the same way as UART0.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds the missing GRF bit definitions for UART3 on the RK3399.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Heiko Schocher <hs@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This board still doesn't select CONFIG_DM and seems to be umaintained.
As it makes progress on modernizing several DaVinci drivers more
difficult and the maintainer has not expressed interest in updating
it, this patch proposes to remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
Add a driver which supports transmitting digital sound to an audio codec.
This uses fixed parameters as a device-tree binding is not currently
defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a driver for the audio hub. This is modelled as a misc device which
supports writing audio data from I2S.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function enables a peripheral clock and then immediately sets its
divider. Add a delay to allow the clock to settle first. This matches the
delay in other places which do a similar thing.
Without this, the I2S device on Nyan does not init properly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The first clock type appears to have and incorrect setting for out of the
mux outputs. It should be CLK_M, not OSC. Fix it and its only user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
With commit 06985289d4 ("watchdog: Implement generic watchdog_reset()
version") the init sequence has changed in arch_misc_init(), resulting
in a re-appearance of the d-cache issue on MT7688 boards (e.g. gardena).
When this happens, the first (or sometimes later ones as well) TFTP
command hangs and does not complete correctly. This leads to the
assumption that the d-cache is not in a clean state once the ethernet
driver is called (d-cache is used here for the buffers). The old work-
around with the cache flush somehow does not work any more now with
the new code change.
To fix this issue, this patch now removes the old workaround and selects
CONFIG_SYS_MALLOC_CLEAR_ON_INIT for ARCH_MTMIPS. With this option the
complete malloc area is initialized with zeros (cache lines are touched).
Testing has shown that this also fixes the issue on the MT7688 boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Finding bitstream from cff-file is no longer valid after bitstream is built
into FIT image and loaded by generic firmware loader. Remove cff-file
as this is legacy implementation from A10 downstream.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
- Add STM32MP1 DDR driver update:
These update introduce the DDR interactive mode described in:
https://wiki.st.com/stm32mpu/index.php/U-Boot_SPL:_DDR_interactive_mode
This mode is used by the CubeMX: DDR tuning tool.
https://wiki.st.com/stm32mpu/index.php/STM32CubeMX
The DDR interactive mode is NOT activated by default because
it increase the SPL size and slow down the boot time
(200ms wait added).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=meeB
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190523' of https://github.com/pchotard/u-boot
- Add various STM32MP1 fixes for serial, env, clk, board, i2c ...
- Add STM32MP1 DDR driver update:
These update introduce the DDR interactive mode described in:
https://wiki.st.com/stm32mpu/index.php/U-Boot_SPL:_DDR_interactive_mode
This mode is used by the CubeMX: DDR tuning tool.
https://wiki.st.com/stm32mpu/index.php/STM32CubeMX
The DDR interactive mode is NOT activated by default because
it increase the SPL size and slow down the boot time
(200ms wait added).
This patches move dspi bus-related operations into more
proper location, to avoid the driver to declares them as externs.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
This patch adds basic dts files for all the m68k boards.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
[trini: Add CONFIG_TARGET_M5329EVB dtbs and update M5329EVB defconfigs]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds a basic group of devicetrees, one for each
cpu family, including actually just uart and dspi devices,
since these are the drivers supporting devicetree (support
added in this patch-set).
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
On SoCFPGA A10 systems, it can rarely happen that a reboot from Linux
will result in stale data in PL310 L2 cache controller. Even if the L2
cache controller is disabled via the CTRL register CTRL_EN bit, those
data can interfere with operation of devices using DMA, like e.g. the
DWMMC controller. This can in turn cause e.g. SPL to fail reading data
from SD/MMC.
The obvious solution here would be to fully reset the L2 cache controller
via the reset manager MPUMODRST L2 bit, however this causes bus hang even
if executed entirely from L1 I-cache to avoid generating any bus traffic
through the L2 cache controller.
This patch thus configures and enables the L2 cache controller very early
in the SPL boot process, clears the L2 cache and disables the L2 cache
controller again.
The reason for doing it in SPL is because we need to avoid accessing any
of the potentially stale data in the L2 cache, and we are certain any of
the stale data will be below the OCRAM address range. To further reduce
bus traffic during the L2 cache invalidation, we enable L1 I-cache and
run the invalidation code entirely out of the L1 I-cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Pull the PL310 clearing code into common code, so it can be reused
by Arria10.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Manage power supply configuration for board using stpmic1
with LPDDR2 or with LPDDR3:
+ VDD_DDR1 = 1.8V with BUCK3 (bypass if possible)
+ VDD_DDR2 = 1.2V with BUCK2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update DDR configuration with the latest update:
- PUBL_regs: DXnGCR[0]= according to ddr_width to disable Byte
lane 2/3 in 16bit
- fix LPDDR2/3 timing_calc to step RL/WL in relaxed
timings mode
- remove LPDDR3 RL3 (optional) support vs MR0[7]
because MR0[7] can't be read instead always apply
worse RL/WL for LPDDR3 when freq < 166MHz)
- change MR3 to 48ohm drive for LPDDR2/3
- change default ZPROG[7:4] = 0x1 for LPDDR2/3 ,
'0' is not allowed even when ODT not used
- use DQSTRN for LPDDR2/3 (it was not set in PIR)
- LPDDR3: set dqsge/dwsgx gate extension to 2,2
like LPDDR2
-DDRCTRL.dfitmg0:
+ for LPDDR3 tphy_wrlat = WL (as LPDDR2)
+ improvement for relaxed mode vs RL/Wl at corner case.
For example @533MHz RL/WL (relaxed) = 9/5 for LPDDR2/3
and correction to MR2 accordingly
- DDR_PCFGQOS1_1: port1 timeout relaxed from 0x00 to 0x40,
for LTDC.
- DDR_PCFGWQOS0_0: change vpr level from
11 to 12 in order to include the CPU on
the variable priority queue.
- DDR_SCHED: fix to consider 13 levels (13 levels - 1 = 0xC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the needed configurations for bootstage and
activate bootstage command.
BOOTSTAGE_REPORT is not activated by default.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
In initf_bootstage() we call bootstage_mark_name() which ends up calling
timer_get_us() before timer_init(); that cause crash for stm32mp1.
This patch solve the issue without changing the initialization sequence.
See also commit 97d20f69f5 ("Enable CONFIG_TIMER_EARLY with bootstage")
for other solution when DM is activated for TIMER.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
