Add the MMC DT node to the Octeon EBB7304 DT file including the
regulator node for the MMC power supply.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the MMC DT node to the Octeon CN73xx dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Until now, the Octeontx MMC driver did only support the ARM Octeon
TX/Tx2 platforms. This patch adds support for the MIPS Octeon platform
to this driver. Here a short summary of the changes:
- Enable driver compilation for MIPS Octeon, including the MMC related
header file
- Reorder header inclusion
- Switch to using the clk framework to get the input clock
- Remove some functions for MIPS Octeon, as some registers don't
exist here
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The MT7688KN is a multi-chip package with 8MiB DDR1 KGD. So the DDR type
from bootstrap register must be ignored, and always be assumed as DDR1.
This patch fixes the displayed DDR type of mt7628.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The MT7688KN is a multi-chip package with 8MiB DDR1 KGD. So the DDR type
from bootstrap register must be ignored, and always be assumed as DDR1.
This patch fixes an issue that mt7628_ddr_pad_ldo_config() may be passed
with a wrong ddr_type in MT7688KN.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Make sure to reset the switch core at probe time.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Import the i.MX6SX based UDOO Neo dts files from Linux 5.12-rc1
and sync the i.MX6SX pinfunc.h
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for stack protector for UBOOT, SPL, and TPL
as well as new pytest for stackprotector
Signed-off-by: Joel Peshkin <joel.peshkin@broadcom.com>
Adjust UEFI build flags.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The current usage of the variable CFLAGS_NON_EFI on the x86 architecture
deviates from other architectures.
Variable CFLAGS_NON_EFI is the list of compiler flags to be removed when
building UEFI applications. It is not a list of flags to be added anywhere.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
So far U-Boot was hard coding a (surely sufficient) memory size of 512
MB, even though all machines out there have at least 4GB of DRAM.
Since U-Boot uses its memory knowledge to populate the EFI memory map,
we are missing out here, at best losing everything beyond 4GB on Midway
boxes (which typically come with 8GB of DRAM).
Since the management processor populated the DT memory node already with
the detected DRAM size and configuration, we use that to populate
U-Boot's memory bank information, which is the base for the UEFI memory
map.
This finally allows us to get rid of the NR_DRAM_BANKS=0 hack, that we
had in place to avoid U-Boot messing up the DT memory node before
loading the kernel.
Also, to cover the whole of memory, we need to enable PHYS_64BIT.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
All Calxeda machines are actually a poster book example of device tree
usage: the DT is loaded from flash by the management processor into
DRAM, the memory node is populated with the detected DRAM size and this
DT is then handed over to the kernel.
So it's a shame that U-Boot didn't participate in this chain, but
fortunately this is easy to fix:
Define CONFIG_OF_CONTROL and CONFIG_OF_BOARD, and provide a trivial
function to tell U-Boot about the (fixed) location of the DTB in DRAM.
Then enable DM_SERIAL, to let the PL011 driver pick up the UART platform
data from the DT. Also define AHCI, to bring this driver into the driver
model world as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
use 'select' to enable IRQ as it does not have architecture
specific dependency.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The GICv3 RM requires "The first 1KB of memory for the LPI Pending tables
must contain only zeros on initial allocation, and this must be visible
to the Redistributors, or else the effect is UNPREDICTABLE".
And as the following statement, we here clear the whole Pending tables
instead of the first 1KB.
"An LPI Pending table that contains only zeros, including in the first 1KB,
indicates that there are no pending LPIs.
The first 1KB of the LPI Pending table is IMPLEMENTATION DEFINED. However,
if the first 1KB of the LPI Pending table and the rest of the table contain
only zeros, this must indicate that there are no pending LPIs."
And there isn't any pending LPI under U-Boot, so it's unnecessary to
load the contents of the Pending table during the enablement, then set
the GICR_PENDBASER.PTZ flag.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # NXP LS1028A
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable PCIe by default in u-boot, this should eventually be made dynamic
in the runtime board config depending on the MCU configuration.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The sync of the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2") causes Ethernet to break on some
ODROID-C2. The PHY seems to need proper reset timing to be functional
in U-Boot and Linux afterwards. Readd the old PHY reset bindings for
dwmac until we support the new bindings in the PHY node.
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmB9NEccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBp1CACFd9d7fokb59aFGeta
RaVD4Ni/5WUMT2ulUWYVn2KPmDLouXKZfvQZxakTJJkLCKfIKpQJ6pw82SUPqNc1
xhFS+YOxuDwhbB6ksApq7eUOga9T/K3S/8T4gPWkAOsAwlJGeF5AE1uxWFLbiNzt
eC2kMtRnwHmRq+fOuLsz1EHHKGcp+mtOnXEy2tv23xcGMqeCPzGsK7DWp1dw66gc
sqj7RdkfP/Ies557Ai/NjfdiOx1ThuVmNz/CgJgVf2/vHiQNgi4jHHDYQG55nGzJ
ExLtlom0L3ttko/hlznANFfPD6PBeF03T1cOT8jgx9/RFIF6dqDoA1YOa2dajhuW
xq5k
=MPfk
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.07-b' of https://source.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.07 cycle:
This small feature set include support for 5th PIO bank on pio4 pinctrl
driver and a fix for the SPL on sama5d3.
This reverts commit 38d6b7ebda.
struct global_data contains a pointer to the bd_info structure. This
pointer was populated spl_set_bd() to a pre-allocated bd_info in the
".data" section. The referenced commit replaced this mechanism to one
that uses malloc(). That new mechanism is only used if SPL_ALLOC_BD=y.
which very few boards do.
The result is that (struct global_data)->bd is NULL in SPL on most
platforms. This breaks falcon mode, since arch_fixup_fdt() tries to
access (struct global_data)->bd and set the "/memory" node in the
devicetree. The result is that the "/memory" node contains garbage
values, causing linux to panic() as it sets up the page table.
Instead of trying to fix the mess, potentially causing other issues,
revert to the code that worked, while this change is reworked.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
in the early SPL boot stage whenever there is a call to udelay,
dm_timer_init fails to find the pit timer whenever it traverses
the device tree, if this property is not present
Signed-off-by: Manuel Reis <mluis.reis@gmail.com>
CC: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
This is a patchset which makes away with the .bind() controller indexing
workaround which was broken since before v2021.04, and then adds PHY
support and MX8M support on top of that. Better add it into the release
early to get as much testing as possible done, because this really does
a lot of changes to the ehci-mx6 driver.
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells, so that the generic PHY framework
can parse the PHY bindings without any extra hacking.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The standard compatible string is "usb-nop-xceiv", use it.
Note that keystone-k2g.dtsi already uses the aforementioned
compat string, so this patch can only remove the override.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
According to latest errata of J721e [1], HS400 mode is not supported
in MMCSD0 subsystem (i2024) and SDR104 mode is not supported in MMCSD1/2
subsystems (i2090). Therefore, replace mmc-hs400-1_8v with mmc-hs200-1_8v
in MMCSD0 subsystem and add a sdhci mask to disable SDR104 speed mode.
Also, update the itap delay values for all the MMCSD subsystems according
the latest J721e data sheet[2]
[1] - https://www.ti.com/lit/er/sprz455/sprz455.pdf
[2] - https://www.ti.com/lit/ds/symlink/tda4vm.pdf
Fixes: 70e167495a ("arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This adds support for devices with R40 dual rank DRAM, and asymmetric
A64 DRAM devices like the Pinephone/3GB.
Also we enable automatic gzipped kernel support, and allow scripted
DT overlay support. The rest of the patches are cleanups, but also
some sunxi-specific preparatory patches for USB3.0 and improved HDMI
support. The bulk of those changes will go through other trees, though.
Build-tested for all 156 sunxi boards, and boot tested on a A64, A20, R40,
H5, H6 and H616 board. USB, SD card, eMMC, HDMI and Ethernet all work
there (where applicable), with the exception of Ethernet on the H5. Since
this is already broken in v2021.04, I will send a separate fix.
Currently sunxi Makefile manually specifies full path to dw-hdmi common
code. However, that is not needed because it can be selected in Kconfig
instead.
Select proper symbol in Kconfig and drop path from Makefile.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The FIT description has access to the configuration variables. Use the
appropriate variable instead of hardcoding the address.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
binman can fill in the default FIT configuration index as selected by
the "default-dt" argument, which is set to CONFIG_DEFAULT_DEVICE_TREE.
Let's respect the user's configuration by taking advantage of this
feature, instead of always defaulting to the first device tree in
CONFIG_OF_LIST.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Previously we do not have proper dual rank memory detection on R40
(because we omitted PIR_QSGATE, which does not work on R40 with our
configuration), and dual rank memory is just simply disabled as early
R40 boards available (Banana Pi M2 Ultra and Berry) have single rank
memory.
As a board with dual rank memory (Forlinx OKA40i-C) is now known to us,
we need to have a way to do memory rank detection to support that board.
Add some routine to detect memory rank by trying to access the memory
in rank 1 and check for error status of the memory controller, and then
enable dual rank memory on R40.
Similar routine can be used to detect half DQ width (which is also
detected by PIR_QSGATE on other SoCs), but it's left unimplemented
because there's no known R40 board with half DQ width now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: Move R40 detect code call into sunxi_dram_init()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Previously we have known that R40 has a configuration register for its
rank 1, which allows different configuration than rank 0. Reverse
engineering of newest libdram of A64 from Allwinner shows that A64 has
this register too. It's bit 0 (which enables dual rank in rank 0
configuration register) means a dedicated rank size setup is used for
rank 1.
Now, Pine64 scheduled to use a 3GiB LPDDR3 DRAM chip (which has 2GiB
rank 0 and 1GiB rank 1) on PinePhone, that makes asymmetric dual rank
DRAM support necessary.
Add this support. The code could support both A64 and R40, but because
dual rank detection is broken on R40 now, we cannot really use it on R40
currently.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
update ls1028aqds networking protocol, config in ls1021atwr, env in ls1012a
Add seli3 board support, booke watchdog, update eTSEC support in ppc-qemu
Add DM_SERIAL and lpuart in sl28, add DM_ETH support for some of powerpc platforms
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Minor fix to Apollo Lake devicetree bindings for FSP
- Refactor Designware PCIe drivers to core and SoC parts
- Add Amlogic Meson Designware PCIe controller driver
Add the FMan v3 nodes for the T1042D4RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T1042 SoC.
The device tree nodes are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When two FMan's are present on a board, the MDIO nodes are found at the
same offsets inside each FMan. This causes "non unique device name"
errors when registering the MDIO nodes under the second FMan. Fix this
by updating the offsets of the MDIO nodes to include the parent FMan's
offset.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the FMan v3 nodes for the T4240RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the QorIQ DPAA 1 FMan v3 device tree nodes for the T4240 SoC.
The device tree nodes are copied over with little modification
from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add the FMan v3 nodes for the T2080RDB. The nodes are copied over with
little modification from the Linux kernel source code.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
