ti_omap3_common contains a lot of common header definitions that help
reduce the size of the zoom1 config file. So, use the generic header
and customize as needed for the platform (example: no spl).
Signed-off-by: Nishanth Menon <nm@ti.com>
This is more in line with commits
664979a2a9f764b63b8094458b87247d254b0cc1(omap3_beagle: remove JFFS2
support.) and 102ce9ea7a (omap3_beagle:
enable CMD_FS_GENERIC and simplify load of image/ramdisk)
CMD_FS_GENERIC allows us to simplify where we load up our image from
either from ext2/fat etc. So, lets use that instead of cumbersome
options we'd have to use. Sticking with existing conventions,
defaults will be:
bootfile=uImage
bootpart=0:1 (first partition)
bootdir=/ (/ in first partition)
Signed-off-by: Nishanth Menon <nm@ti.com>
CONFIG_SYS_GENERIC_BOARD should now be enabled for generic
functionality Further information in doc/README.generic-board
Signed-off-by: Nishanth Menon <nm@ti.com>
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Port configurations are defined in board.c.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
currently only spi0 is enabled on k2hk evm. This
configuration update is needed to enable spi1 and spi2.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.
This patch add support for keystone architecture and k2hk evm.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
- add davinci driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Convert to using the common config files. This requires a little more
flexibility in the common files than we had been using before.
Signed-off-by: Tom Rini <trini@ti.com>
We previously only supported QSPI_1 (single) support. Add QSPI_4 (quad)
read support as well. This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value. We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment. When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This is only useful with the _spiboot build target anyhow, so only
include it then. Drop CONFIG_SPL_OS_BOOT support then as the flash is
small and didn't include a spot for the device tree already.
Signed-off-by: Tom Rini <trini@ti.com>
In general, we want to load the DT at base+128MB, so that we ahve
sufficient room for the kernel and a larger device tree. In the case of
OMAP3, use 64MB instead as we have a number of boards with 128MB DDR.
Signed-off-by: Tom Rini <trini@ti.com>
To deal with a reoccurring problem properly we need to specify addresses
for the Linux kernel, Flatted Device Tree and ramdisk that obey the
constraints within the kernel's Documentation/arm/Booting file but also
make sure that we relocate things within a valid address range.
It is possible with these addresses to also set fdt_high and initrd_high
to the value of 0xffffffff. We don't do this by default to allow for
the most likely success of people using custom addresses however.
Signed-off-by: Tom Rini <trini@ti.com>
This mainly converts the am335x_spl_bch driver to the "normal" format
which means a slight change to nand_info within the driver.
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
Jetson TK1 is an NVIDIA Tegra124 reference board, which shares much of
its design with Venice2.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
RiOTboard is produced by Embest/Element 14 and is based on i.MX6 Solo
The following features are tested :
- UART2 (console)
- eMMC
- SDCard
- uSDCard
- Ethernet
- USB Host (through 4 ports hub)
- HDMI output
- I2C 1/2/3
- LVDS TFT with LCD8000-97C from Embest/Element 14
Boot on eMMC and through USB loader are tested.
For more informations on this board : http://www.riotboard.org/
MarSBoard is produced by Embest/Element 14 and is based on i.MX6 Dual
The following features are tested :
- UART2 (console)
- eMMC
- uSDCard
- Ethernet
- USB Host (through 2 ports hub)
- HDMI output
- I2C 1/2
- SPI NOR Flash
- LVDS TFT with LCD8000-97C from Embest/Element 14
Boot on SPI NOR and through USB loader are tested.
For more informations on this board :
http://www.embest-tech.com/shop/star/marsboard.html
Both boards are supported by the same code base as they are based on a
common trunk of schematics.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Commit d016dc42ce changed the layout of BCH8 SW
on omap3 boards. We need to adopt the ecc layout for the nand_spl_simle
driver to avoid wrong ecc errors.
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Cc: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Cc: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch add gicv3 support to uboot armv8 platform.
Changes for v2:
- rename arm/cpu/armv8/gic.S with arm/lib/gic_64.S
- move smp_kick_all_cpus() from gic.S to start.S, it would be
implementation dependent.
- Each core initialize it's own ReDistributor instead of master
initializeing all ReDistributors. This is advised by arnab.basu
<arnab.basu@freescale.com>.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
Clock Manager driver will be called to reconfigure all the
clocks setting based on user input. The input are passed to
Preloader through handoff files
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
This change enables automatically uuid generation by command gpt.
In case of updating partitions layout user don't need to care about
generate uuid manually.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: trini@ti.com
The u-boot's image TEXT_BASE needs to be changed to 0x43e00000 from 0x78100000.
This change provides compatibility with other trats2 (RD_PQ) devices
(http://download.tizen.org/releases/system/).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The DRAM size can be easily detected at runtime on i.MX53. Implement
such detection on M53EVK and adjust the rest of the macros accordingly
to use the detected values.
An important thing to note here is that we had to override the function
for trimming the effective DRAM address, get_effective_memsize(). That
is because the function uses CONFIG_MAX_MEM_MAPPED as the upper bound of
the available DRAM and we don't have gd->bd->bi_dram[0].size set up at
the time the function is called, thus we cannot put this into the macro
CONFIG_MAX_MEM_MAPPED . Instead, we use custom override where we use the
size of the first DRAM block which we just detected.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Fix memory access slowness on i.MX53 M53EVK board. Let us inspect the
issue: First of all, the i.MX53 CPU has two memory banks mapped at
0x7000_0000 and 0xb000_0000 and each of those can hold up to 1GiB of
DRAM memory. Notice that the memory area is not continuous. On M53EVK,
each of the banks contain 512MiB of DRAM, which makes a total of 1GiB
of memory available to the system.
The problem is how the relocation of U-Boot is treated on i.MX53 . The
U-Boot is placed at the ((start of first DRAM partition) + (gd->ram_size)) .
This in turn poses a problem, since in our case, the gd->ram_size is 1GiB,
the first DRAM bank starts at 0x7000_0000 and contains 512MiB of memory.
Thus, with this algorithm, U-Boot is placed at offset:
0x7000_0000 + 1GiB - sizeof(u-boot and some small margin)
This is past the DRAM available in the first bank on M53EVK, but is still
within the address range of the first DRAM bank. Because of the memory
wrap-around, the data can still be read and written to this area, but the
access is much slower.
There were two ideas how to solve this problem, first was to map both of
the available DRAM chunks next to one another by using MMU, second was to
define CONFIG_VERY_BIG_RAM and CONFIG_MAX_MEM_MAPPED to size of the memory
in the first DRAM bank. We choose the later because it turns out the former
is not applicable afterall. The former cannot be used in case Linux kernel
was loaded into the second DRAM bank area, which would be remapped and one
would try booting the kernel, since at some point before the kernel is started,
the MMU would be turned off, which would destroy the mapping and hang the
system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The DRAM size can be easily detected at runtime on i.MX53. Implement
such detection on MX53QSB and adjust the rest of the macros accordingly
to use the detected values.
An important thing to note here is that we had to override the function
for trimming the effective DRAM address, get_effective_memsize(). That
is because the function uses CONFIG_MAX_MEM_MAPPED as the upper bound of
the available DRAM and we don't have gd->bd->bi_dram[0].size set up at
the time the function is called, thus we cannot put this into the macro
CONFIG_MAX_MEM_MAPPED . Instead, we use custom override where we use the
size of the first DRAM block which we just detected.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Fix memory access slowness on i.MX53 MX53QSB board. Let us inspect the
issue: First of all, the i.MX53 CPU has two memory banks mapped at
0x7000_0000 and 0xb000_0000 and each of those can hold up to 1GiB of
DRAM memory. Notice that the memory area is not continuous. On MX53QSB,
each of the banks contain 512MiB of DRAM, which makes a total of 1GiB
of memory available to the system.
The problem is how the relocation of U-Boot is treated on i.MX53 . The
U-Boot is placed at the ((start of first DRAM partition) + (gd->ram_size)) .
This in turn poses a problem, since in our case, the gd->ram_size is 1GiB,
the first DRAM bank starts at 0x7000_0000 and contains 512MiB of memory.
Thus, with this algorithm, U-Boot is placed at offset:
0x7000_0000 + 1GiB - sizeof(u-boot and some small margin)
This is past the DRAM available in the first bank on MX53QSB, but is still
within the address range of the first DRAM bank. Because of the memory
wrap-around, the data can still be read and written to this area, but the
access is much slower.
There were two ideas how to solve this problem, first was to map both of
the available DRAM chunks next to one another by using MMU, second was to
define CONFIG_VERY_BIG_RAM and CONFIG_MAX_MEM_MAPPED to size of the memory
in the first DRAM bank. We choose the later because it turns out the former
is not applicable afterall. The former cannot be used in case Linux kernel
was loaded into the second DRAM bank area, which would be remapped and one
would try booting the kernel, since at some point before the kernel is started,
the MMU would be turned off, which would destroy the mapping and hang the
system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Add support for PCIe on MX6 SabreSDP board and enable the support
in the config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Liu Ying <Ying.Liu@freescale.com>
Use of PCIe on SABRE Lite and Nitrogen6x boards
is atypical and requires the use of custom daughter
boards.
Use in U-Boot is even rarer, so this patch removes it from
the standard configuration.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
CONFIG_BOOT_INTERNAL is not used anywhere, so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add yet another OCOTP driver for this i.MX family. This time, it's a driver for
the OCOTP variant found in the i.MX23 and i.MX28. This version of OCOTP is too
different from the i.MX6 one that I could not use the mxc_ocotp.c driver without
making it into a big pile of #ifdef . This driver implements the regular fuse
command interface, but due to the IP blocks' limitation, we support only READ
and PROG functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
When using HAB, there are additional special requirements on the placement of
U-Boot and the U-Boot SPL in memory. To fullfill these, this patch moves the
U-Boot binary a little further from the begining of the DRAM, so the HAB CST
and IVT can be placed in front of the U-Boot binary. This is necessary, since
both the U-Boot and the IVT must be contained in single CST signature. To
make things worse, the IVT must be concatenated with one more entry at it's
end, that is the length of the entire CST signature, IVT and U-Boot binary
in memory. By placing the blocks in this order -- CST, IVT, U-Boot, we can
easily align them all and then produce the length field as needed.
As for the SPL, on i.MX23/i.MX28, the SPL size is limited to 32 KiB, thus
we place the IVT at 0x8000 offset, CST right past IVT and claim the size
is correct. The HAB library accepts this setup.
Finally, to make sure the vectoring in SPL still works even after moving
the SPL from 0x0 to 0x1000, we add a small function which copies the
vectoring code and tables to 0x0. This is fine, since the vectoring code
is position independent.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
On the boards this target supports this option is either non possible
without hardware mods (Beaglebone White/Black) or not supported due to
board design. Drop this and regain some space.
Signed-off-by: Tom Rini <trini@ti.com>
This allows to use exynos random number generator by enabling configs:
- CONFIG_EXYNOS_ACE_SHA
- CONFIG_LIB_HW_RAND
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
cc: Piotr Wilczek <p.wilczek@samsung.com>
cc: Minkyu Kang <mk7.kang@samsung.com>
New configs:
- CONFIG_LIB_RAND - to enable implementation of rand library in lib/rand.c
- CONFIG_LIB_HW_RAND - to enable hardware based implementations of lib rand
Other changes:
- add CONFIG_LIB_RAND to boards configs which needs rand()
- put only one rand.o dependency in lib/Makefile
CONFIG_LIB_HW_RAND should be defined for drivers which implements rand library
(declared in include/common.h):
- void srand(unsigned int seed)
- unsigned int rand(void)
- unsigned int rand_r(unsigned int *seedp)
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Tom Rini <trini@ti.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
as the siemens boards use dfu for updating a nand ubi partition
add DFU_MANIFEST_POLL_TIMEOUT to them, so dfu host waits after
complete transfer of the new image for DFU_MANIFEST_POLL_TIMEOUT
ms before sending again an usb request. So the board have enough
time to erase rest of the nand sectors.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
As Simon Glass requested it, here's a patch that enables
CONFIG_CMD_LZMADEC in sandbox.
Signed-off-by: Patrice Bouchand <pbfwdlist@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
CONFIG_LEON is already defined in
arch/sparc/cpu/{leon2,leon3}/config.mk.
Remove the redundant definition in board header files.
All leon3 boards define CONFIG_LEON3 in board header files.
Move the definition to arch/sparc/cpu/leon3/config.mk.
CONFIG_LEON2 can be move to arch/sparc/cpu/leon2/config.mk
as well.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Enable the Chrome OS EC emulation for sandbox along with LCD, sound
expanded GPIOs and a few other options to make this work correctly.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2s code is in fact Samsung-specific, but there might be other
implementation. Move this code into its own file. This makes it slightly
more obviously how to adjust the code to support another SoC, when someone
takes this task on.
Also drop non-FDT support, since it isn't used on Exynos 5.
Tested-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The current 4MB size is a little small for some tests, so increase it.
Reviewed-by: Hung-ying Tyan <tyanh@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Pull out "$(SRCTREE)/" from CONFIG_SYS_KWD_CONFIG
and push it into the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Dave Purdy <david.c.purdy@gmail.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Siddarth Gore <gores@marvell.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Eric Cooper <ecc@cmu.edu>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
Pull out "$(SRCTREE)/" from CONFIG_SYS_FSL_PBL_PBI
and CONFIG_SYS_FSL_PBL_RCW and push it into the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
enabling CONFIG_MACB makes other locations in the stamp config file
enable network related commands (actually prevents disabling them)
enable USB ethernet support by activating generic support as well as
Asix and Moschip ethernet adapters
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Andreas Bießman <andreas.devel@googlemail.com>
enable support for the Moschip USB ethernet adapter for those boards
which previously had support for "all other" USB ethernet adapters
(that's Asix _and_ SMSC) enabled -- which applies to harmony, m53evk,
mx53loco, nitrogen6x, omap3_beagle
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
adjust the harmony and omap3_beagle board configs to make
their CONFIG_USB_ETHER_* items appear in alphabetical order
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Patch a7e36fc9 (mtd: nand: omap: remove unused #defines from common
omap_gpmc.h) removed some MTD related defines. Including
GPMC_NAND_ECC_LP_x8_LAYOUT. But this define is also needed for the
memory controller configuration (only the x8 defines are needed,
the x16 defines are the default). Without it the NAND subsystem is
not configured correctly and booting into U-Boot does not work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pekon Gupta <pekon@ti.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
When using the am335x_evm_nor target one is generally expecting to be
used in an environment when you want to program the NOR and not a
"deployment" type target. In addition this only supports the Beaglebone
White with the memory cape and NOR module installed, which precludes the
presence of SPI flash. Drop SPI as we were getting close to the binary
limit in some cases and slightly over with other toolchains.
Signed-off-by: Tom Rini <trini@ti.com>
This patch enables to run Trats2 board on device tree.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to run Trats board on device tree.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to run Universal board on device tree.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables to run Origen board on device tree.
Uart, DRAM and MMC init functions are removed as their
generic replacements form the common board file are used.
The config file is modified to contain only board specific options.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds common dtsi file and config header for all
Exynos 4 based boards.
Patch additionaly adds board specific (weak) functions for
board_early_init_f and board_power_init functions.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Allow the boot of a device tree mainline kernel by aligning the environment
variables with other FSL boards.
Tested NFS boot of a dt 3.14-rc5 kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
Gateworks Ventana is a product family based on the i.MX6. This
patch adds support for all boards in the Ventana family. Where
possible, data from the boards EEPROM is used to determine various
details about the board at runtime.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
CONFIG_SYS_HZ must be always 1000, but M5271EVB.h defines it
as 1000000 and idmr.h defines it as (50000000 / 64).
When compiling these two boards, a warning message is displayed:
time.c:14:2: warning: #warning "CONFIG_SYS_HZ must be 1000
and should not be defined by platforms" [-Wcpp]
There are no board maintainers for them so this commit just
deletes them.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jason Jin <Jason.jin@freescale.com>
Add NAND SPL boot support with hardware PMECC.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add SPI SPL boot support for sama5d3xek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add sama5d3 Xplained board support which use Atmel SAMA5D36 SoC.
Now it supports boot from NAND flash and SD/MMC card.
Features support:
- NAND flash
- SD/MMC card
- Two USB hosts
- Ethernet (one GMAC, one EMAC)
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[reorder boards.cfg]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for using the Atmel MCI driver on at91sam9263ek.
This change is modeled after the existing at91sam9260ek support.
Please note that this hooks up slot1 (MCI1) for SD. Not both.
Tested with at91bootstrap and u-boot on dataflash in slot 0
and fat-formatted 8GB SDHC in slot 1 on first revision
at91sam9263ek (which must use dataflash in slot0 to boot).
CONFIG_ATMEL_MCI_PORTB not tested.
Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se>
[remove empty line]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Update following DDR related settings for T1040RDB, T1042RDB_PI
-Correct number of chip selects to two as t1040 supports
two Chip selects.
-Update board_specific_parameters udimm structure with settings
derived via calibration.
-Update ddr_raw_timing sructure corresponding to DIMM.
-Set ODT to off. Typically on FSL board, ODT is set to 75 ohm,
but on T104xRDB, on setting this , DDR instability is observed.
Board-level debugging is in progress.
Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
T1040 has internal display interface unit (DIU) for driving video.
T1040QDS supports video mode via
-LCD using TI enconder
-HDMI type interface via HDMI encoder
Chrontel, CH7301C encoder which is I2C programmable is used as
HDMI connector on T1040QDS.
This patch add support to
-enable Video interface for T1040QDS
-route qixis multiplexing to enable DIU-HDMI interface on board
-program DIU pixel clock gerenartor for T1040
-program HDMI encoder via I2C on board
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080PCIe-RDB is a Freescale Reference Design Board that hosts the T2080 SoC.
It works in two mode: standalone mode and PCIe endpoint mode.
T2080PCIe-RDB Feature Overview
------------------------------
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
DDR Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LP devices
- 72bit 4GB DDR3-LP SODIMM in slot
Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Two 10Gbps SFP+ ports on-board
- Two 10Gbps Base-T ports on-board
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes 16 lanes configuration:
- SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10)
- SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
- SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3)
- SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2)
- SerDes-2 Lane E-F: to C293 secure co-processor (PCIe2 x2)
- SerDes-2 Lane G-H: to SATA1 & SATA2
IFC/Local Bus:
- NOR: 128MB 16-bit NOR flash
- NAND: 512MB 8-bit NAND flash
- CPLD: for system controlling with programable header on-board
eSPI:
- 64MB N25Q512 SPI flash
USB:
- Two USB2.0 ports with internal PHY (both Type-A)
PCIe:
- One PCIe x4 gold-finger
- One PCIe x4 connector
- One PCIe x2 end-point device (C293 Crypto co-processor)
SATA:
- Two SATA 2.0 ports on-board
SDHC:
- support a TF-card on-board
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Change QIXIS timing parameter CONFIG_SYS_CS3_FTIM2 to 8 from 0.
Fix EMI2 for t2080qds, which was caused by adding t2081qds.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.
All boards with mpc8260 cpu defined both of them:
- CONFIG_MPC8260 was defined in board config headers
and include/common.h
- CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk
We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.
This commit does:
- Delete CONFIG_8260 and CONFIG_MPC8260 definition
in config headers and include/common.h
- Rename CONFIG_8260 to CONFIG_MPC8260
in arch/powerpc/cpu/mpc8260/config.mk.
- Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
All mips32 boards define CONFIG_MIPS32 in config headers
except malta boards which define it in boards.cfg.
We can consolidate them by defining it in
arch/mips/cpu/mips32/config.mk.
CONFIG_MIPS64 definition can be moved to
arch/mips/cpu/mips64/config.mk as well.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Before this commit, USE_PRIVATE_LIBGCC was defined in
arch-specific config.mk and referenced in
arch/$(ARCH)/lib/Makefile.
We are not happy about parsing config.mk again and again.
We have to keep the same behavior with a different way.
By adding "CONFIG_" prefix, this macro appears
in include/autoconf.mk, include/spl-autoconf.mk.
(And treating USE_PRIVATE_LIBGCC as CONFIG macro
is reasonable enough.)
Tegra SoC family defined USE_PRIVATE_LIBGCC as "yes"
in arch/arm/cpu/arm720t/tegra*/config.mk,
whereas did not define it in arch/arm/cpu/armv7/tegra*/config.mk.
It means Tegra enables PRIVATE_LIBGCC only for SPL.
We can describe the same behavior by adding
#ifdef CONFIG_SPL_BUILD
# define CONFIG_USE_PRIVATE_LIBGCC
#endif
to include/configs/tegra-common.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Many (but not all) of Blackfin boards give -O2 option
to compile under lib/ directory.
That means lib/ should be speed-optimized,
whereas other parts should be size-optimized.
We want to keep the same behavior,
but do not want to parse board/*/config.mk again and again.
We've got no choice but to invent a new method.
CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED, if it is enabled,
gives -O2 flag only for building under lib/ directory.
Dirty codes which I had marked as "FIX ME"
in board/${BOARD}/config.mk have been deleted.
Instead, CONFIG_CC_OPTIMIZE_LIBS_FOR_SPEED has been
defined in include/configs/${BOARD}.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
As ppc4xx currently only supports the deprecated nand_spl infrastructure
and nobody seems to have time / resources to port this over to the newer
SPL infrastructure, lets remove NAND booting completely.
This should not affect the "normal", non NAND-booting ppc4xx platforms
that are currently supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Tested-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Enable required clocks for GPIO to fix a boot issue introduced by commit
f33b9bd398 (arm: omap3: Enable clocks for
peripherals only if they are used).
Without this patch the u-boot freezes after the following messages
OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-200MHz, Max CPU Clock 1 Ghz
IGEPv2 + LPDDR/NAND
I2C: ready
DRAM: 512 MiB
NAND: 512 MiB
MMC: OMAP SD/MMC: 0
Diving into the issue, the sequence that produces the u-boot freezes is
setup_net_chip
|--> gpio_direction_out
|--> _set_gpio_dataout
|--> __raw_writel
To avoid this we just need enable the clocks for GPIOs that are used, but it
would be interesting implement a mechanism to protect these situations and
make sure that the clock is enabled when we request a GPIO.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
This retrieves a PXE config file over the network, and executes it. This
allows an extlinux config file to be retrieved over the network and
executed, whereas the existing bootcmd_dhcp retrieves a U-Boot script.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Update the common Tegra boot scripts in the default environment to
a) Make use of the new "test -e" shell command to avoid some error
messages.
b) Allow booting using the sysboot command and extlinux.conf. This
allows easy creation of boot menus, and provides a simple interface
for distros to parameterize/configure the boot process.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Modify all Tegra boards to include the "distro defaults" header, so that
all the config options distros expect are enabled. Remove any #defines
that enable the same options from the Tegra files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra's EHCI controllers only have a single PORTSC register. Configure
U-Boot to know this. This prevents e.g. ehci_shutdown() from touching
non-existent registers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
<asm/arch-tegra/tegra.h> needs to use CONFIG_TEGRA* to conditionalize
some definitions, since some modules moved between generations. Move
the definition of CONFIG_TEGRAnn to a header that's included earlier,
so that it's set by the time tegra.h needs to use it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
- GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND)
- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
- GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND)
2) removes unused #defines in common omap_gpmc.h depending on above configs
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
As an example of how to write a uclass and a driver, provide a demo version
of each, accessible through the 'demo' command.
To use these with driver model, define CONFIG_CMD_DEMO and CONFIG_DM_DEMO.
The two demo drivers are enabled with CONFIG_DM_DEMO_SIMPLE and
CONFIG_DM_DEMO_SHAPE.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
This command is not required for driver model operation, but can be useful
for testing. It provides simple dumps of internal data structures.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Add some tests of driver model functionality. Coverage includes:
- basic init
- binding of drivers to devices using platform_data
- automatic probing of devices when referenced
- availability of platform data to devices
- lifecycle from bind to probe to remove to unbind
- renumbering within a uclass when devices are probed/removed
- calling driver-defined operations
- deactivation of drivers when removed
- memory leak across creation and destruction of drivers/uclasses
- uclass init/destroy methods
- automatic probe/remove of children/parents when needed
This function is enabled for sandbox, using CONFIG_DM_TEST.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for building a device tree for sandbox's CONFIG_OF_HOSTFILE
option to make it easier to use device tree with sandbox.
This adjusts the Makefile to build a u-boot.dtb file which can be passed
to sandbox U-Boot with:
./u-boot -d u-boot.dtb
Signed-off-by: Simon Glass <sjg@chromium.org>
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
Since the switch may be re-configured for VLAN usage in Linux (or any
other OS), lets reset the switch to its default register values upon
power-up. Otherwise network might not be available in U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Tom Rini <trini@ti.com>
Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also adding mii command support to am335x common config.
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Adding support for CPSW to AM43xx EPOS nad GP EVM which is connected
to RMII and RGMII phy respectively and enable cpsw in config.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
With this, fixup a trivial build error of get_effective_memsize needing
to be updated in the new board/freescale/p1010rdb/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
Same as the previous commit.
Move sanity check to prepare1 target to avoid nasty troubles.
Before this commit, LDSCRIPT existence was not checked
when it was specified by CONFIG_SYS_LDSCRIPT.
Now LDSCRIPT existence is checked for all boards.
$(wildcard $(LDSCRIPT)) must point to the linker scripts
with absolute path.
Otherwise, make will terminate with a false error
on out-of-tree build.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
u-boot binary size for Freescale mpc8536DS platforms is 512KB.
This has been reached to upper limit of the platforms and causig
linker error. So increase the u-boot binary size to 768KB.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In the previous patches, we introduced the SPL/TPL fraamework.
For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The
SPL was loaded by the code from the internal on-chip ROM. The SPL initializes
the DDR according to the SPD and loads the final uboot image into DDR, then
jump to the DDR to begin execution.
For NAND booting way, the nand SPL has size limitation on some board(e.g.
P1010RDB), it can not be more than 8KB, we can call it "minimal SPL", So the
dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is
loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD
and loads the final uboot image into DDR,then jump to the DDR to begin execution.
This patch enabled SPL/TPL for P1010RDB to support starting from NAND/SD/SPI
flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL.
Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to
execute, so the section .resetvec is no longer needed.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There was no enough memory for malloc in SPL booting from spi flash, so
relayout the memory in SPL: reduce the memory for global data from 16K
Bytes to 4K Bytes, save the space for malloc.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There was no enough stack in SPL, so the buffer needed in SPL is to malloc
from memory pool and to repalce the temporary variable.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. The SPL's length of SDCARD boot has not enough,expand the SPL's
length to 128K.
2. deleted unused symbol: CONFIG_SYS_RUN_INDDR
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2081 QDS is a high-performance computing evaluation, development and
test platform supporting the T2081 QorIQ Power Architecture processor.
T2081QDS board Overview
-----------------------
- T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
- 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC)
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving
- Ethernet interfaces:
- Two on-board 10M/100M/1G bps RGMII ports
- Two 10Gbps XFI with on-board SFP+ cage
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
- Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- SerDes:
- 8 lanes up to 10.3125GHz
- Supports SGMII, HiGig, XFI, XAUI and Aurora debug,
- IFC:
- 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
- USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- PCIe:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- eSDHC:
- Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and
voltage translators
- I2C:
- Four I2C controllers.
- UART:
- Dual 4-pins UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for the bcm28155_ap reference board.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
Rework rpi_b's bootcmd (and sub-commands) to match Tegra's bootcmd as
much as possible. This will aid in a future patch which will create a
common header e.g. config_distro_bootcmd.h.
While at it, enable booting from extlinux.conf using the sysboot command.
The iteration and componentization currently makes a little more sense
for Tegra than RPi, but I'd still like to keep the two as similar as
possible. USB and networking support is coming to the RPi in due course,
and it'll all make more sense then anyway.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Commit 6789e84eca (i2c, omap24xx:
convert driver to new mutlibus/mutliadapter framework) intended to
make I2C driver compatible with latest changes. It unfortunately has
had a impact on size on SPL as well. For example on SDP4430,
32032 bytes before/MLO
35416 bytes after/MLO
With this mentioned commit, MLO stops booting on SDP4430 as only 32K
is accessible for non-secure (bootloader) s/w on GP devices and the size
increase to 56K fails boot.
On the latest u-boot commit e7be18225f,
MLO is now at size 35592 bytes, However, I2C is not necessary for SPL
to function as we use SR_I2C for controlling the PMIC.
Disabling I2C reduces MLO to 32224 bytes which allows
OMAP4 GP platform to boot up.
Since this is common for all OMAP4 platforms, remove the need for I2C
for SPL builds in the common config.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sricharan R <r.sricharan@ti.com>
With CONFIG_SYS_BOOTMAPSZ defined, recent Linux kernel booting
results in this error:
Booting using the fdt blob at 0x81f00000
Loading Kernel Image ... OK
ERROR: Failed to allocate 0x1189d bytes below 0x80004000.
device tree - allocation error
FDT creation failed! hanging...### ERROR ### Please RESET the board ###
Removing this define solves this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Patch contains the same fixes as commit
4b9b2c300a
(missing CONFIG_OMAP3_GPIO_2) and commit
f9095aac793aa8917ab9b915c5d449e6dc8d3d30 (missing CONFIG_SPL_NAND_SOFTECC).
Same issues are relevant for the mcx board, too.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Patch f33b9bd3
[arm: omap3: Enable clocks for peripherals only if they are used]
breaks SPL booting on tao3530. Since some gpio input's are
read to detect the board revision. But with this patch above, the
clocks to the GPIO subsystems are not enabled per default any more.
The GPIO banks need to be configured specifically now.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB
Motherboard, using TI's AM3352 SoC.
Most of code is derived from TI's AM335x_EVM
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: trini@ti.com
Adds support for Bernecker & Rainer Industrieelektronik GmbH T-Series
Motherboard, using TI's AM3352 SoC.
Most of code is derived from TI's AM335x_EVM
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
This patch add support for the Silica Pengwyn board [1]
The board is based on a TI AM3354 CPU [2]
All jumpers removed it will boot from the SDcard, the console is on
UART1 accessible via the FDTI -> USB. The on board NAND flash is
supported and can act as boot medium, depending on jumper settings.
USB Host, USB Device and Ethernet are also provided but untested.
[1]
http://www.silica.com/product/silica-pengwyn-board.html
[2]
http://www.ti.com/product/am3354
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
[trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused
spi0_pin_mux from Pengwyn support]
Signed-off-by: Tom Rini <trini@ti.com>
The Pi has no flash to store an environment in the usual fashion. However,
the user may wish to customize the environment. We know that the SD card
must be present, since that's where the boot ROM has loaded U-Boot from.
So, load uEnv.txt from there early during boot. This allows the user to
e.g. customize boot_targets, in order to automatically select network
boot.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Modify the rpi_b board to include the "distro defaults" header, so that
all the config options distros expect are enabled. Remove any #defines
that enable the same options from the rpi_b.h.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Proper spelling of the boad marketing name is with upper case.
So changing it from lower case to upper case here.
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Conflicts:
Makefile
drivers/net/npe/Makefile
These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
Having CONFIG_SYS_I2C_BASE requires DW I2C driver to explicitly include
<arch/hardware.h> which other platforms may not have at all.
It's always good to have a driver platform-independent.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>
CONFIG_SYS_GBL_DATA_SIZE is not used any more.
The size of struct "global_data" is automatically calculated
by asm-offsets. (See lib/asm-offsets.c)
GENERATED_GBL_DATA_SIZE should be used instead of
CONFIG_SYS_GBL_DATA_SIZE.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This commit removes platform CONFIG_SYS_HZ definition for the
remainders of part1 (commit cdb23792) and part2 (commit f232950f).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Since the generic ls command no longer segfaults sandbox, enable it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
SPL is using ps7_init.c/h files which are generated
from design tools which have to be copied to
boards/xilinx/zynq folder before compilation.
BSS section is moved to SDRAM because fat support
requires more space than SRAM size.
Added:
- MMC and QSPI support
- Boot OS directly from SPL
- Enable SPL command
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Define both serial uarts in the driver and return
default uart based on board configuration.
- Move baseaddresses to hardware.h
- Define default baudrate and clock values
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extend max kernel image size. Gunzip is checking
this value. If kernel is larger, message below is shown.
Uncompressing Kernel Image ... Error: inflate() returned -5
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
KMSUGP1 is from a u-boot perspective (almost) identical to KMNUSA.
The only difference is that the PCIe reset is connected to Kirkwood pin
MPP7_PEX_RST_OUTn, we use a dedicated config flag KM_PCIE_RESET_MPP7.
Such pin should theoretically be handled by the PCIe subsystem
automatically, but this turned out not to be the case.
So simply configure this PIN as a GPIO and issue a pulse manually.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Cc: Valentin Longchamp <valenting.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Add set_fdthigh subcommand to "subbootcmds" (release) so to set "fdt_high"
This is necessary on Kirkwood so that the FDT does not get relocated
above the memory limit that the kernel cannot access
(that is the memory part reserved for the switch).
This was tested on NUSA1, where it is necessary, and on ETER1, where it
doesn't seem to hurt.
We want the scripts to also work with older versions of u-boot, where:
a) set_fdthigh is not defined (will be default env for newer u-boots)
b) the fdt will not be available
For this reason, we use "set_fdthigh" to tell whether we are running
a newer (FDT-aware) u-boot or not.
So if "set_fdthigh" runs successfully or arch != arm we try loading
the fdt; otherwise we proceed normally.
Notice how, contrary to release mode, set_fdthigh will _not_ be part of
subbootcmds for develop and ramfs, but will be executed as part of
"tftpfdt".
Since this is only needed for kirkwood cards, and it prevents the kernel
from booting on QorIQ (though it seemed to work on ETER1), we change
its definition in the default env for powerpc so that the value is only
set on ARM.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This consists of:
a) Defining the addresses, enabling fdtsupport [arm]
b) Defining "cramfsloadfdt" [arm,powerpc => common]
c) Adding the FDT address to bootm [arm,powerpc => common]
d) Defining "tftpfdt" in ramfs-,develop- [arm,powerpc >= common]
This should work with 3.10 kernels, whether loaded through TFTP
(with rootfs either through NFS or TFTP-ramfs) or from the NAND.
The machid was left unchanged, this should keep compatibility with both
older and newer kernels.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This is needed for board specific additional environment variables.
E.g. the mgcoge3un has this additional "waitforne" variable.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
We now use 256MB RAM instead of 128MB. We can use the same config file
as kmnusa.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch is here because of:
"arm: keep all sections in ELF file"
(sha1: 47ed5dd031)
Our tools expect to have elf with only LOAD header.
Without this fix also PHDR, INTERP and DYNAMIC headers
are available in ELF.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot names the Raspberry Pi board rpi_b. This means that the common
expression for DTB filename ${soc}-${board}.dtb expands to
bcm2835-rpi_b.dtb. However, the DTB generated by the Linux kernel is
bcm2835-rpi-b.dtb. Set $fdtfile in U-Boot's environment so that scripts
look for the correct DTB filename.
An alternative would be to rename the U-Boot board to rpi-b. However,
that change would be far more invasive, and end up affecting users (i.e
they'd have to change their U-Boot build commands).
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Similarly as it was done on commit 6584a1b526 (ARM: mx6: Change the FDT loading
address to avoid overlaping), we need to adjust the fdt_addr in order to be
able to boot FSL 3.10 kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Add a README to the board which lists the commands required to enable
booting from the eMMC boot partitions found on the board.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a README to the board which lists the commands required to enable
booting from the eMMC boot partitions found on the board.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Now that the designware ethernet driver uses phylib we need to turn it
on here.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
* Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
* Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
* Support of custom phy initialization is now done with existing
"board_phy_config".
Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.
For example:
* CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
* CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used
I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
AXS101 is a new generation of devlopment boards from Synopsys that houses
ASIC with ARC700 and lots of DesignWare peripherals:
* DW APB UART
* DW Mobile Storage (MMC/SD)
* DW I2C
* DW GMAC
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Arcangel4 is a FPGA-based development board that is used for prototyping and
verificationof of both ARC hardware (CPUs) and software running upon CPU.
This board avaialble in 2 flavours:
* Little-endian (arcangel4)
* Big-endian (arcangel4-be)
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch modifies envs to enable dual kernel boot
- with separated DTB if the DTB file is loaded successfully;
- with DTB apppended to uImage if DTB file is not found;
This is neccesssary for backward compatibilty.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds variables describing platform (soc, board, vendor)
to default environment.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
The board is unmaintained, just like the rest of the IXP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
Add support for U-BOOT SPL. NOR and RAM mode are supported.
There are 3 images in NOR flash. u-boot.img, dtb and kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix the timeout issue after running "bootp" command in U-Boot console.
TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10 after a
controller reset and before RUN bit is set (per technical reference
manual).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These are the board files for Venice2 (Tegra124), plus the AS3722 PMIC
files. PMIC init will be moved to pmic_common_init later.
This builds/boots on Venice2, SPI/MMC/USB/I2C all work. Audio, display
and WB/LP0 are not supported yet.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
$usb_need_init prevents "usb start" from being run multiple times for
each boot attempt, i.e. once for USB storage, another for PXE, and
another for DHCP. However, the flag that's used to determine when to run
"usb start" is never cleared, so a subsequent "boot" command will never
probe for a freshly plugged in USB device. Fix this so that new USB
devices will be probed once per boot attempt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The U-Boot "cardhu" build supports only revision 4 of the Cardhu board
and later compatible revisions. Hence, set $board_name in the default
environment to "cardhu-a04" rather than just "cardhu".
The Linux kernel has separate DTs for Cardhu A02 and A04, although the
former isn't really supported any more. Consequently, the kernel DT file
that matches the U-Boot cardhu build is "tegra30-cardhu-a04.dtb" rather
than "tegra30-cardhu.dtb". Set the $fdtfile default environment variable
to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The new prototype and the final series was moved from Micron to Spansion
to have a better reset sequence that is easier to support.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This define can be used if the ubi boot partition (defined for all
Keymile boards with KM_UBI_PARTITION_NAME_BOOT #define to ubi0) needs
some additionnal boot options.
This is the case for the kmp204x boards since u-boot does not support
NAND Flash subpage accesses on this platform, an additionnal argument
that defines the VID offstet must be given to the kernel.
The UBI cmd line option now looks like this "ubi.mtd=ubi0,2048" on this
platform.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The kmcoge4 board is the product board derived from the kmlion1
prototype. The main difference between the 2 boards is that the kmcoge4
does not configure the Local Bus controller for LCS2.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to boards.cfg to keep targets in order]
Signed-off-by: York Sun <yorksun@freescale.com>
This patch adds support for using some GPIOs that are connected to the
I2C bus to force the bus lines state and perform some bus deblocking
sequences.
The KM common deblocking algorithm from board/keymile/common/common.c is
used. The GPIO lines used for deblocking the I2C bus are some external
GPIOs provided by the QRIO CPLD:
- SCL = GPIOA_20
- SDA = GPIOA_21
The QRIO GPIOs act in an open-drain-like manner, for 0 the line is
driven low and for 1 the GPIO is set as input and the line gets
pulled-up.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Make use of the QRIO1 32bit register at 0x20 as bootcounter register
Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
This covers only non-L2 switch ethernet interfaces i.e.
RGMII and SGMII interface for both T1040RDB and T1042RDB_PI
T1040RDB is configured as serdes protocol 0x66 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
1 SGMII on DTSEC3
T1042RDB_PI is configured as serdes protocol 0x06 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: Minor change in commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
Add usb2 node entry to hwconfig default
Remove DDR controller interleaving from hwconfig
Move SPI related macros out of "#ifdef CONFIG_SPIFLASH"
Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible in u-boot
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Fix commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
Add usb2 node entry in "hwconfig string"
Remove controller interleaving from hwconfig string as T1040
has only one DDR conroller
SPI related macros which were earlier under #ifdef CONFIG_SPIFLASH
are move outside so that they are defined for all cases as these
macros are also used by other u-boot code
Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
This change allows updating environment stored on MMC by dfu or thor.
New setting:
- "params.bin mmc 0x38 0x8"
File params.bin can be generated by: tools/mkenvimage.
e.g. ./mkenvimage -s 4096 -o params.bin <env_text_file>
Every new env variable in text file should start with a new line.
Sample env text file:
- board/samsung/common/dfu_sample_env.txt
Requirements:
- file name: "params.bin"
- file size: 4096 Bytes - the same as CONFIG_ENV_SIZE.
Other size will cause CRC miscalculation at boot.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
CC: Piotr Wilczek <p.wilczek@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Changes:
- check image bpp instead of resolution when returns logo address
- remove 32bpp logo
- add 16bpp logo in two formats: bmp and gzipped bmp
- init logo address with "0" for unsupported bpp mode
- update boards configs with proper image size for gunzip
- extend structure vidinfo by two fields: logo_x_offset and logo_y_offset.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Old s5p gpio coding method was not clean and was not working properly
for all parts and banks. New method is clean and easy to extend.
Gpio coding mask:
0x000000ff - pin number
0x00ffff00 - bank offset
0xff000000 - part number
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enable CONFIG_REGEX on M53EVK to allow usage of regular expressions
on environment variables.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The name the Linux kernel expects is 'mxc_nand' , not 'mxc-nand' .
This patch renames the driver name.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
We do not have to define CONFIG_MPC5xxx in board config headers
(and start.S) because it is defined in arch/powerpc/cpu/mpc5xxx/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Define CONFIG_MPC86xx in arch/powerpc/cpu/mpc86xx/config.mk
because all target boards with mpc86xx cpu define it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk
because all target boards with mpc85xx cpu define it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
We do not have to define CONFIG_MPC824X in board config headers
because it is defined in arch/powerpc/cpu/mpc824x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
We do not have to define CONFIG_MPC512X in board config headers
because it is defined in arch/powerpc/cpu/mpc512x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
We do not have to define CONFIG_MPC83xx in board config headers
because it is defined in arch/powerpc/cpu/mpc83xx/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
We do not have to define CONFIG_4xx in board config headers
because it is defined in arch/powerpc/cpu/ppc4xx/config.mk.
include/configs/JSE.h defines "CONFIG_4x", not "CONFIG_4xx".
I believe it is a typo because "CONFIG_4x" is not used at all
in other files.
So, I also deleted "CONFIG_4x" in include/configs/JSE.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Like other architectures, CONFIG_AVR32 can be defined
in arch/avr32/config.mk rather than board header files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Upon further inspection of relevant parts of the architecture, the
maximum SPL binary size is 220KiB.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Create a new file, include/configs/ti_omap3_common.h, for everything
common to the OMAP3 SoC leaving just the board specific part to board
configuration file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
If CONFIG_NR_DRAM_BANKS is not defined, we say (for simplicity) that we have
1 bank, but for some boards should be interesting that we can define
CONFIG_NR_DRAM_BANKS. To handle this possibility just define the number of
DRAM banks if is not already defined. This is useful for some OMAP3 boards
where the DRAM initialitzation is only at u-boot level.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
The ELM hardware engine wihich is used for ECC error detections is not present
on OMAP3 SoC, so move the CONFIG_SPL_NAND_AM33XX_BCH from ti_armv7_common.h to
SoC configuration file.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Follow the pattern ti_<processor family>_common.h used by other TI processors
to be coherent. So just rename omap5_common.h to ti_omap5_common.h.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Follow the pattern ti_<processor family>_common.h used by other TI processors
to be coherent. So just rename omap4_common.h to ti_omap4_common.h.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The upper 4 data signals of esdhc are shared with spi flash.
So detect if the upper 4 pins are assigned to esdhc before
enable sdhc 8 bit width.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
