The current value CTLUPD_AREF(0) is the reset value of the register,
so there is no need to write a value. If needed, the register can be
written using board specific CR settings.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The CR80 register has multiple interrupt bits, the code is supposed
to check bit 8 but instead uses a logical and. In most cases this
probably did not affect real operations since at that stage typically
none of the other bits are set.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
According to the data sheet bits 10-8 are PHYDRAM_CK_EN. Fix mask
to allow setting PHYDRAM_CK_EN correctly.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Commit 3f353ceccb ("vf610: refactor DDRMC code") changed on-die
termination (ODT) values from 120 Ohm to 60 Ohm and enabled a static
read/write leveling which has not been tested with this board. This
commit reverts both changes and makes sure that memory gets
initialized as it has been done before the mentioned commit.
Fixes: 3f353ceccb ("vf610: refactor DDRMC code")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter
5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed
for correct operation of DDR. Assume the default DDR pin configuration
which seems to work well on a Colibri VF50.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Safe some space by not selecting CMD_NFS and CMD_LOADS/B.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
After updating the value of dev_context_ptrs[0], we should flush this
from cache to memory. Otherwise the xhci controller won't use it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In order to keep SPL code size below the 32Kb limit,
put under CONFIG_SPL_BUILD flag all unused code in SPL.
This is needed for stm32f7xx board which are using SPL.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In case "gpio-ranges" property is not present in device tree,
use default value for gpio_count and gpio_range.
This fixes an issue on stm32 F7 and H7 boards where "pinmux status -a"
command didn't return any pin status due to the fact that both stm32 F7
and H7 board DT doesn't use the gpio-ranges property.
Fixes: dbf928dd2634a6("gpio: stm32f7: Add gpio bank holes management")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove unused Android partitions:
- efs, crypto, cache: we don't use it anymore (images are not built
in AOSP
- ipu1, ipu2: IPU firmware is now a part of vendor image and doesn't
reside as a separate partition
While at it, rename "reserved" partition to "uboot-env", as it's
actually stores U-Boot environment.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
The env location label ENVL_ESATA is missed in location tables, so
when we configure the ENV in SATA, u-boot fails to get correct env
location and cause boot hang in board_f.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When running usb dwc3 gadget driver, we meet random USB enumeration failure in fastboot.
The root cause is a cache coherence issue. When it happens, the ctrl_req in
gadget driver is allocated at 0xfe932f40, and the usb_composite_dev (cdev)
is allocated at 0xfe932f60. So after we submit the setup request (cache flushed) to USB
controller, any accessing to usb_composite_dev variable will cause the cache line refill, then
when setup transfer is completed, reading the setup data in ctrl_req will gets old value from
cache not from memory.
The ctrl_req is allocated by API dma_alloc_coherent, but u-boot don't have cohernet memory.
so it still needs cache maintain operations before/after HW accessing. Since the cache flush or
invalidate bases on cache line, so when the allocated memory size is not cache line aligned,
potentially it may meet such issue.
This patch modifies the dma_alloc_coherent API to round the size to cache line aligned.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
I can't continue maintaining the board because I don't have access to the
hardware anymore, so remove myself from the entry and add Javier who has
volunteered to help and maintain the board.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Javier Martínez Canillas <javier@dowhile0.org>
On our mirror account on github we have gotten a handful of pull
requests. At this time github does not allow you to disable pull
requests on a project. The generally suggested work-around is to add a
pull request template that tells people to not use that workflow. Add
one here that points to the wiki page on submitted patches.
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit d0851c8937 ("blk: Call part_init() in the post_probe() method")
removed the call to part_init() in mmc.c, as this is done by the DM_MMC
framework.
However Allwinner is (still) relying on a non-DM MMC driver, so we are
now missing the implicit partition init, leading to failing MMC accesses
due to the missing partition information.
Bring the call back just for non-DM MMC driver to fix this regression.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Soeren Moch <smoch@web.de>
There is no code for using partition labels in the Allwinner SPL port.
Even so the name is slightly misleading, CONFIG_SPL_LIBDISK_SUPPORT was
meant to guard partition code for the SPL.
Remove the "imply" line in the Kconfig to make this obvious and avoid
unneeded code inclusions, helping to keep the H6 SPL code small.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When checking for boards that are enabling a SATA driver that isn't
converted to DM yet we need to be sure to not also trip over boards that
do set CONFIG_DM_SCSI by itself, as that is not a bug.
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Fixes: ea9d7c17fc ("dm: MIGRATION: Add migration plan for CONFIG_SATA")
Signed-off-by: Tom Rini <trini@konsulko.com>
Braces around the error-case for rk3399_pinctrl_set_pin_pupd lead to
an unconditional (and unintended) return from the function without it
ever setting pin-configurations.
Fix it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- clamp DRAM size to below 32bit for 32bit targets to support 4GB
- fix copyright notice on some Rockchip-contributed files
- adjust vdd_log for the RK3399-Q7 to improve stability in some workloads
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcLfBzAAoJECaAFcEOcohNrMoH/ihFAiFblzVN7XPRTpV8+GGJ
gsljC7DRGkgMT7IOnmCE+/44RGaQnP3bHQH6WG4zVHZ6vhrEyzqPaYzbzLg90ujj
k1k4N6op3NA6e40FZvHzB/aglx1e5UFnWxstBpT1g82sL8xLSs0ubhsq6+gcr29I
0qGTILHxwY95qUGDi2zlYNEwv5B0enlucfhB5kTZ7QYZX+Jz1SL4AI0sIapTdMg+
/Bcu1Qi6B+xVklDhz9NUpYgst8T3J0Gabq7mqMXwommAgejsrjQWOnhDRrrWznd+
OsJqEEo/TmdT/eqO7SffooKiEUPrw6YmKPtZAXkdlc8Cm+qZRvr/okozALBJizY=
=v3QG
-----END PGP SIGNATURE-----
Merge tag 'for-master-20190103' of git://git.denx.de/u-boot-rockchip
Last-minute fixes for 2019.1:
- clamp DRAM size to below 32bit for 32bit targets to support 4GB
- fix copyright notice on some Rockchip-contributed files
- adjust vdd_log for the RK3399-Q7 to improve stability in some workloads
Building peach-pi smdk5420 and peach-pit with thumb mode for SPL
ends-up in the following error:
Error: Thumb encoding does not support an immediate here -- `msr cpsr_c,#0x13|0xC0'
Use an intermediate register to be able to use thumb for exynos5 SPL.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch sets VDD_LOG to 950 mV on RK3399-Q7.
This is required to address stability issues on Puma
in heavy-load use-cases.
Reported-by: Assaf Agmon <assaf@r-go.io>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch enables the full pinctrl driver in the defconfig
for the RK3399-Q7.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds a Kconfig option to enable the full pinctrl driver
for the RK3399. This flag needs to be enabed in order to get the
features of the full pinctrl driver compiled in (i.e. a .set_state()
callback).
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The current pinctrl driver for the RK3399 has a range of qulity issues.
E.g. it only implements the .set_state_simple() callback, it
does not parse the available pinctrl information from the DTS
(instead uses hardcoded values), is not flexible enough to cover
devices without 'interrupt' field in the DTS (e.g. PWM),
is not written generic enough to make code reusable among other
rockchip SoCs...
This patch addresses these issues by reimplementing the whole driver
from scratch using the .set_state() callback.
The new implementation covers all featurese of the old code
(i.e. it supports pinmuxing and pullup/pulldown configuration).
This patch has been tested on a RK3399-Q7 SoM (Puma).
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
pinctrl_decode_pin_config_dm() is basically a feature-equivalent
implementation of pinctrl_decode_pin_config(), which operates
on struct udevice devices and uses the dev_read_*() API.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch enables the PWM regulator driver in the defconfig
for the RK3399-Q7.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch allows to enable the PWM regulator driver
independent for U-Boot and SPL.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch eliminates the non-standard entries "rockchip,pwm_id"
and "rockchip,pwm_voltage". They are neither documented nor
read out by any driver.
Additionally it introduces the entry regulator-init-microvolt
and sets it to 900 mV, which is the default target value
for VDD_LOG.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip may use this sdram copy of source code for both open source
and internal project, update the license to use both GPL2.0+ and
BSD-3 Clause.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
All the source code of sdram_rk3036.c are from Rockchip, update the
copyright to owned by Rockchip.
Because rockchip may use this copy of code both for open source
project and internal project, update the license to use both
GPL2.0+ and BSD-3 Clause.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is workaround for issue we can't get correct size for 4GB ram
in 32bit system and available before we really need ram space
out of 4GB, eg.enable ARM LAPE(rk3288 supports 8GB ram).
The size of 4GB is '0x1 00000000', and this value will be truncated
to 0 in 32bit system, and system can not get correct ram size.
Rockchip SoCs reserve a blob of space for peripheral near 4GB,
and we are now setting SDRAM_MAX_SIZE as max available space for
ram in 4GB, so we can use this directly to workaround the issue.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
- v2019.04 for no dm conversion drivers
- v2019.07 for partially converted drivers.
Note: there were many updates on this deadline, so better
not update this again.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This patch adds Hynix H27UBG8T2BTR id table as part of raw nand,
these chips were available in some A20-olinuxino-micro boards.
Signed-off-by: Nikolai Zhubr <n-a-zhubr@yandex.ru>
[jagan: add proper commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Current driver doesn't check if the destination pointer is NULL.
This cause the data from the FIFO to be stored inside the internal
SDRAM ( address 0 ).
The patch add simple check if the destination pointer is NULL.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[jagan: fix commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot binary has grown in such a way that it goes beyond the reserved
area for the environment variables.
Running "saveenv" causes U-Boot to hang because of this overlap.
Fix this problem by increasing the CONFIG_ENV_OFFSET size.
Also, in order to prevent this same problem in the future, use
CONFIG_BOARD_SIZE_LIMIT, which will detect the overlap in build-time.
CONFIG_BOARD_SIZE_LIMIT does not accept math expressions, so declare
CONFIG_ENV_OFFSET with its direct value instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
