Enable CONFIG_OF_SYSTEM_SETUP to let U-Boot could disable
device tree nodes that could not be used by Linux.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When resource is not assigned to non-secure Linux, if linux continue
to use the node, linux may crash or hang. So need to set the node
status to disabled for not owned resources.
The resource id is in the power-domains property in device tree,
so parse the power-domains property to get the resource id and
use scfw api to check whether it is owned by current partition.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since SCU MU driver has been bound in dm_init, so we don't need to
bind it again. Just replace by using uclass function to probe it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because FIT could not be used for AHAB secure boot on i.MX8,
so switch to use container image that could let SPL verify
ATF and U-Boot with AHAB.
Enable HUSH_PARSER in defconfig to make run netboot could work.
Note: The AHAB related code has not been added.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because FIT could not be used for AHAB secure boot on i.MX8,
so switch to use container image that could let SPL verify
ATF and U-Boot with AHAB.
Note: The AHAB related code has not been added.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8 only support AHAB secure boot with Container format image,
we could not use FIT to support secure boot, so introduce container
support to let SPL could load container images.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add parsing i.MX8 Container file support, this is to let
SPL could load images in a container file to destination address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The first stage of flash.bin is larger than 584 * 512, so when
writting u-boot.itb, some data will be override. Enlarge the
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to fix boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The changes were added by following patch:
commit <9002e735e717> ("imx: mx6sabresd: fix boot hang with video")
commit <f45ec8fcfb86> ("imx6: dts: add 'u-boot, dm-pre-reloc' to soc and ipu nodes")
Let's move the U-Boot specific change to imx6qdl-u-boot.dtsi
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since commit 6e1f4d2652 ("arm: imx-common: add SECURE_BOOT option
to Kconfig") the SECURE_BOOT option is selected through Kconfig.
Cleanup comments in code to align with this change.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
In case CONFIG_SECURE_BOOT is enabled we need to limit the SPL size to
avoid a possible HAB failure event:
--------- HAB Event 1 -----------------
event data:
0xdb 0x00 0x14 0x42 0x33 0x22 0x33 0x00
0x00 0x00 0x00 0x0f 0x00 0x90 0x70 0x00
0x00 0x01 0x10 0x00
STS = HAB_FAILURE (0x33)
RSN = HAB_INV_ADDRESS (0x22)
CTX = HAB_CTX_TARGET (0x33)
ENG = HAB_ENG_ANY (0x00)
As explained in Commit 23612534fe ("spl: imx6: Provide a SPL_SIZE_LIMIT
default") the i.MX6 SPL size limit is 68KB.
The ROM code is copying the image size defined in boot data to its
respective load address, in case we exceed the OCRAM free region a
HAB invalid address failure event is generated.
The maximum CSF size is defined in CONFIG_CSF_SIZE, reduce SPL size
limit based on this configuration.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000.
mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig
file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently the SPL binary is 67 kB, which leaves only 1 kB of free
internal RAM space.
The following options can be safely removed to save some precious
SPL space:
- CONFIG_SPL_FS_EXT4: u-boot-dtb.img is stored in raw sector via dd
command (at offset 69 kB)
- CONFIG_SPL_I2C_SUPPORT: I2C is not used during SPL
- CONFIG_SPL_OS_BOOT: no need to make Falcon mode supported
by default
After this change the SPL binary size gets down to 51 kB.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
On i.MX7ULP B0, there is change in NIC clock dividers architecture.
On A0, the NIC1 BUS and EXT dividers were in a chain with NIC1 DIV, but
on B0 they are parallel with NIC1 DIV. So now the dividers are independent.
This patch modifies the scg_nic_get_rate function according to this change.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The normal target frequency for ULP A7 core is 500Mhz, but now ROM
set the core frequency to 413Mhz. So change it to 500Mhz in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider
set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU
is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28)
to workaround the problem. The correct fix should let GPU handle the
clock rate in kernel.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The num/denom is a float value, but in the calculation it is convert
to integer 0, and cause the result wrong.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wrong I2c driver configuration name is used in codes, so I2c driver is
not built. Correct it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since many drivers need this CONFIG_MX7ULP to distiguish the settings
for i.MX7ULP only. Add this entry to cpu's kconfig.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The offset for FRAC and the mask for PCD are not correct.
If we set FRAC, we can't get the right frequency. Fix them
to correct value.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX7ULP, value zero is reserved in SCG1 RCCR register,
so the val should be decreased by 1 to get the correct clock
source index.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board will reboot if A7 core enter mem mode by rtc, then M4 core
enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode
to fix this issue.
Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access
it. So check the CPU rev and not apply the settings for B0.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since the SD3.0 kernel driver needs M4 image support, this causes
problem for usb boot booting into kernel. To decouple the relationship,
we modify the FDT file in u-boot to disable SD3.0.
So the kernel won't depend on M4 image.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add CONFIG_DM_GPIO to all defconfigs whose board is
nitrogen6x.
mx6qsabrelite_defconfig
nitrogen6dl2g_defconfig
nitrogen6dl_defconfig
nitrogen6q2g_defconfig
nitrogen6q_defconfig
nitrogen6s1g_defconfig
This is in preparation for adding CONFIG_DM_SPI.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This prevents messages like
gpio@20a0000: get_value: error: gpio GPIO2_2 not reserved
when CONFIG_DM_GPIO is enabled.
Also, when CONFIG_DM_GPIO is enabled, checkboard is too
early to use gpio_get_value, so read it directly on failure.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Add DM_MMC to all defconfigs whose board is
nitrogen6x.
mx6qsabrelite_defconfig
nitrogen6dl2g_defconfig
nitrogen6dl_defconfig
nitrogen6q2g_defconfig
nitrogen6q_defconfig
nitrogen6s1g_defconfig
This commit is adding multiple configs, but
seems to be the minimum change to not lose features
and still compile fine.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
There is no need to use HAB for FIT signature validation when
SPL_FIT_SIGNATURE is also enabled, as that will be validated via the
normal U-Boot signed FIT image flow.
This allows having SPL validated by HAB and the payloads to follow
being validated with FIT signatures only.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q
variants, which are quite similar and already managed via only one
dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in
order to automatically enable the HAS_CAAM and MX6_SMP features.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Commit e37ac717d7 ("Convert to use fsl_esdhc_imx for i.MX platforms")
converted FSL_ESDHC to FSL_ESDHC_IMX, but the config check for
apalis_imx6 wasn't updated accordantly.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Only one dtb is currently supported, so match with imx6-apalis.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Pass spl_image and bootdev to board_return_bootrom.
i.MX8MN needs the args to let ROM to load images
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
i.MX7 and i.MX8M use mxc uart driver, so let's make the SoC could
use MXC_UART kconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Add missed break for HDMI entry.
And moving FIT parsing earlier, because it does not have parameter,
it will not runs into CFG_REG_SIZE.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
fdtdec_get_addr_size could not parse addr/size correctly is
using address-cells 2 and size-cells 2 on an ARM32 SoC.
So switch to use devfdt_get_addr_size_index.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
