Commit Graph

15443 Commits

Author SHA1 Message Date
Christian Hitz
8c2d9c6862 nand: Add more NAND types from Linux nand driver
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe]

This patch merges the additional NAND flash types from the 3.0 Linux
kernel.

Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26 16:09:02 -06:00
Christian Hitz
4c6de8560c nand: Merge BCH code from Linux nand driver
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe]

This patch merges the BCH ECC algorithm from the 3.0 Linux kernel.
This enables U-Boot to support modern NAND flash chips that
require more than 1-bit of ECC in software.

Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26 16:09:02 -06:00
Scott Wood
4d2aee2b36 NAND: Remove additional (CONFIG_SYS)_NAND_MAX_CHIPS
NAND_MAX_CHIPS has been replaced by CONFIG_SYS_NAND_MAX_CHIPS,
and the latter defaults to 1.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26 16:09:01 -06:00
Vladimir Zapolskiy
6bbb3e93a5 NAND: remove NAND_MAX_CHIPS definitions
This change follows the change by Wolfgang Grandegger (commit 6c869637fe),
which allows to remove useless NAND_MAX_CHIPS definitions in board config
files.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26 16:08:55 -06:00
Stefano Babic
d3022c5f5c nand_spl_simple: store ecc data on the stack
Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM
which is likely to contain already loaded data.
The patch saves the oob data and the ecc on the stack replacing
the fixed address in RAM.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Ilya Yanok <yanok@emcraft.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Simon Schwarz <simonschwarzcor@googlemail.com>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26 16:06:21 -06:00
Andreas Müller
137703b811 overo: add SPL support
* implementation based on ti beagleboard/omap3evm
* timing data and i2c workaround for revision 0 boards taken from x-loader
* run-tested with overo revision 0 and 1 / boot from NAND and SDcard
* run-tested with x-loader

Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:13 +01:00
Andreas Müller
761ca31e47 omap_rev_string: output to stdout
* avoid potential buffer overflows
* allow SPL-build not to output "Texas Instruments Revision detection unimplemented"

Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:13 +01:00
Andreas Müller
8775471bb3 OMAP SPL: call timer_init in s_init to make udelay work earlier
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
2012-01-16 08:40:12 +01:00
Andreas Müller
0b620ec97e drivers/i2c/omap24xx_i2c.c: move all local variables to SRAM
At old overo boards TWL4030 RTC irq is connected to gpio112. Unfortunately
this pin is also used for revision detection. Therefore we need to send
shut-up to TWL4030 to avoid reading wrong revision. In SPL this must
be done before SDRAM is set up because the type of SDRAM is revision dependent.
By this patch it is ensured that all variables used by omap24xx_i2c.c are
located in SRAM.

Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:12 +01:00
Andreas Müller
0f8d3eb902 include/configs/omap3_overo.h: several cleanups
* remove unused macros
* remove unused macro values
* align tabs
* remove Free Software Foundation address

Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
2012-01-16 08:40:12 +01:00
Andreas Müller
bae485db12 board/overo/overo.c: replace printf with one argument by puts
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
2012-01-16 08:40:12 +01:00
Andreas Müller
49e9b4bd9b drivers/i2c/omap24xx_i2c.c: replace printf with one argument by puts
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2012-01-16 08:40:12 +01:00
Chandan Nath
8a8f084e4f ARM:AM33XX: Add SPL support for AM335X EVM
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:12 +01:00
Chandan Nath
876bdd6d46 ARM:AM33XX: Add mmc/sd support
This patch add supports for mmc/sd driver on AM335X platform.
PLL and pinmux configurations for mmc/sd are configured in this
patch.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:12 +01:00
Chandan Nath
750b4bfe10 ARM:AM33XX: Fixing AM335X config parameters
This patch is added to correct some of the AM335X config
parameters which were incorrect along with some cleanup
like removing unused code.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:12 +01:00
Chandan Nath
fb072a3ead ARM:AM33XX: Fix ddr and timer register offset
This patch is added to update incorrect ddr and timer
register offset.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2012-01-16 08:40:11 +01:00
Chandan Nath
f16da7466f ARM:AM33XX: Replace CONFIG_AM335X with CONFIG_AM33XX
This patch is added to replace CONFIG_AM335X symbol
with CONFIG_AM333XX for AM33XX platforms.

Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Thomas Weber <weber@corscience.de>
2012-01-16 08:40:11 +01:00
Nikita Kiryanov
e4e2bf5e4c cm-t35: use the new EEPROM module to read the MAC address
Switch to the new EEPROM module and fix the problem of MAC address
being read from the wrong offset due to lack of distinction between
EEPROM layouts.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:11 +01:00
Nikita Kiryanov
7d3c97d71f cm-t35: pass correct revision information to Linux
Read revision from EEPROM and pass it to Linux.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:11 +01:00
Nikita Kiryanov
715462dd7e omap3: make get_board_rev() function weak
Current get_board_rev() function returns a hard coded value which is
obviously incorrect for the majority of boards.
Allow boards to provide a correct implementation by making this function
weak.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:11 +01:00
Nikita Kiryanov
8230925049 cm-t35: add EEPROM module and pass Linux a serial number
Add board specific EEPROM handling module,
read the serial number from the EEPROM and pass it to Linux.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:11 +01:00
Nikita Kiryanov
ce15ec9f69 cm-t35: various cleanups
Move #ifdef CONFIG_SMC911X out of board_eth_init() function,
simplify the board_mmc_init() function, and enclose handle_mac_address()
in the CONFIG_SMC911X.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:11 +01:00
Nikita Kiryanov
9fc376be28 cm-t35: cleanup the config file
Remove values from boolean defines, fix indentation, etc..
No functional changes.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:11 +01:00
Aneesh V
fe7104b307 omap4: fix boot issue on ES2.0 Panda
Fix boot issue on ES2.0 Panda by tuning some
IO settings. The CONTROL_EFUSE_2 register has
to be over-ridden in software for 4430 boards.

Commit 23e9f0723e
wrongly did this for CONTROL_EFUSE_1. Reverting
this and doing it for CONTROL_EFUSE_2.

Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Raúl Porcel <armin76@gentoo.org>
2012-01-16 08:40:11 +01:00
Peter Meerwald
6cce55047c beagle: add eeprom expansion board info for bct brettl3
this is for a prototyping board

vendor/product ids have been added to
http://elinux.org/BeagleBoardPinMux#List_of_Vendor_and_Device_IDs
2012-01-16 08:40:10 +01:00
Peter Barada
86887f8ea1 ARMV7: Add support For Logic OMAP35x/DM37x modules
This patch adds basic support for OMAP35x/DM37x SOM LV/Torpedo
reference boards. It assumes U-boot is loaded to SDRAM with the
help of another small bootloader (x-load) running from SRAM.

Signed-off-by: Peter Barada <peter.barada@logicpd.com>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2012-01-16 08:40:10 +01:00
Christian Riesch
a601bed065 arm, davinci: Change byte order of RTC kick register values
Now the values in the defines agree with those in the manuals.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
2012-01-16 08:40:10 +01:00
Thomas Weber
1378cac669 OMAP3: Remove unused define CONFIG_OMAP3_*_DDR
This patch removes the unused definitions:
CONFIG_OMAP3_MICRON_DDR
CONFIG_OMAP3_NUMONYX_DDR
CONFIG_OMAP3_INFINEON_DDR

Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
2012-01-16 08:40:10 +01:00
Christian Riesch
9452582601 da850evm: Remove CONFIG_SYS_xxCACHE_OFF defines
This patch removes the defines CONFIG_SYS_ICACHE_OFF,
CONFIG_SYS_DCACHE_OFF, and CONFIG_SYS_L2CACHE_OFF from the board
configuration. These defines are useless since cache is
anyway disabled for the entire architecture since commit
cba4b1809f.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Tom Rini <trini@ti.com>
2012-01-16 08:40:10 +01:00
Christian Riesch
441ea7c67b arm, davinci: Use a common configuration file for da850evm and da850_am18xxevm
In commit 06194b6b65 a separate header
file was introduced for the AM1808 EVM, include/configs/da850_am18xxevm.h.
Before this commit, the da850evm.h configuration file was used for both
the AM1808 and the OMAP-L138 EVMs. The only substantial difference
between the da850evm and the da850_am18xxevm configuration is a single
bit in the hardware revision that is passed to the Linux kernel.

This patch removes include/configs/da850_am18xxevm.h. Instead the
include/configs/da850evm.h configuration is used for AM18xx EVMs and
CONFIG_DA850_AM18X_EVM is defined in boards.cfg.

Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Tom Rini <trini@ti.com>
2012-01-16 08:40:10 +01:00
Jason Liu
bc5833c49a i.mx: i.mx6q: add the initial support for i.mx6q Sabre Lite board
Add the initial support for Freescale i.MX6Q Sabre Lite board

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
2012-01-16 08:40:10 +01:00
Jason Liu
f2f7745825 imx: mx6q: add aipstz init for off platform periph
Init peripheral access control register of AIPSTZ OPACRx:

Buffer Writes(BW):      0 -> not bufferable,
Supervisor Protect(SP): 0 -> not require supervisor privilege level for accesses.
Write Protect(WP):      0 -> allows write accesses.
Trusted Protect(TP):    0 -> allows unstrusted master

Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:10 +01:00
Zach Sadecki
8db9eff6c5 mx28: fix clearing of IRQs in power init
There are 2 locations in the power init code for the mx28 where IRQs are not being cleared because incorrect methods to clear those bits were being used.  This was causing my board to get stuck waiting for POWER_CTRL_VDD5V_DROOP_IRQ to clear.  Using the correct method to clear the IRQs fixes it.

Signed-off-by: Zach Sadecki <zach@itwatchdogs.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-01-16 08:40:10 +01:00
Marek Vasut
c660a54182 M28EVK: Fix build if CONFIG_CMD_NAND not selected
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:10 +01:00
Fabio Estevam
b0216fd62a m28evk: Remove 'all' target from Makefile
Remove 'all' target from Makefile, as this is unused code.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-01-16 08:40:09 +01:00
Fabio Estevam
1084606c97 m28evk: Use GENERATED_GBL_DATA_SIZE
Use GENERATED_GBL_DATA_SIZE for calculating CONFIG_SYS_INIT_SP_OFFSET.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-01-16 08:40:09 +01:00
Fabio Estevam
d109ed946c mx28evk: Remove 'all' target from Makefile
Remove 'all' target from Makefile, as this is unused code.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-01-16 08:40:09 +01:00
Marek Vasut
e364daf925 MX28: Fix MXSBOOT segfault if no params specified
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:09 +01:00
Jason Liu
bd2e27c043 i.mx6:imx6q: allign MAC address with burned-in ordering
For the i.mx6q, the burned-in MAC address will be the following odering,

fuse: 0x620[7:0]   MAC_ADDR[7:0]     ---> mac[5]
fuse: 0x620[15:8]  MAC_ADDR[15:8]    ---> mac[4]
fuse: 0x620[23:16] MAC_ADDR[23:16]   ---> mac[3]
fuse: 0x620[31:24] MAC_ADDR[31:24]   ---> mac[2]
fuse: 0x630[7:0]   MAC_ADDR[39:32]   ---> mac[1]
fuse: 0x630[15:8]  MAC_ADDR[47:40]   ---> mac[0]

This patch also fix the error caculation for the fuse bank[0] address

Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:09 +01:00
Fabio Estevam
29f75a5ce5 mx28evk: Add initial support for MX28EVK board
Add initial support for Freescale MX28EVK board.

Tested boot via SD card and by loading a kernel via TFTP through
the FEC interface.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:09 +01:00
Fabio Estevam
5bcc6a8901 mx28: Let dram_init be common for mx28
Let dram_init function be a common function, so that other mx28 boards
can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
2012-01-16 08:40:09 +01:00
Fabio Estevam
5cb525f3d2 mx28: Let imx_get_mac_from_fuse be common for mx28
Let imx_get_mac_from_fuse function be a common function, so that other
mx28 boards can reuse it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:09 +01:00
Fabio Estevam
be252b654a net: imx: Add multi-FEC support for imx_get_mac_from_fuse
Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter.

This feature is important on mx28 SoC for example that has two FEC ports.

Cc: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:09 +01:00
Eric Nelson
3c057897e9 i.mx6q: mx6qarm2: Enable the usboh3 clock
Bits 0 and 1 of CCM_CCGR7 are the usboh3 clock enable bits. Enabling this
clock is necessary for the USB download.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
CC: Jason Hui <jason.hui@linaro.org>
Acked-by: Jason Hui <jason.hui@linaro.org>
2012-01-16 08:40:08 +01:00
Veli-Pekka Peltola
00699f847d mx28: remove omap specific config options
Config options for OMAP are not used with i.MX28 so remove dead code.

Signed-off-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:08 +01:00
Jason Liu
473c63592e i.mx6q: arm2: Add the enet function support
This enable the network function on the i.mx6q armadillo2
board(arm2), thus we can use tftp to load image from network.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
2012-01-16 08:40:08 +01:00
Jason Liu
2ef2b95095 fec: add the i.mx6q enet driver support
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:08 +01:00
Jason Liu
ff167df51c i.mx: i.mx6q: Add the enet clock function
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:08 +01:00
Stefan Kristiansson
f1f441afc4 openrisc: Add MAINTAINERS entry
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
2012-01-13 21:17:08 +01:00
Stefan Kristiansson
deddf5d2e3 openrisc: Add architecture to MAKEALL
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
2012-01-13 21:17:04 +01:00