The BCM5482 PHY supports both copper and fiber as an ethernet medium.
By enabling its copper/fiber mode auto-detection feature it can
dynamically determine if it should be configured for copper or fiber.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This is generally good practice and saves ~150 bytes.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
- Remove unnecessary printing "Enet starting in <speed>/<duplex>"
This same information is already printed during normal ethernet
operation in the form "Speed: 1000, full duplex".
- Add a check for link before determining link speed and duplex
If there is no link, speed/duplex don't matter. This also removes
the annoying and unneeded "Auto-neg error, defaulting to 10BT/HD"
message that occurs when no link is detected.
- Whitespace and line > 80 characters cleanup
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
In SGMII mode the link between a processor's internal TBI PHY and an
external PHY should always be 1000Mbps, full duplex. Also, the SGMII
interface between an internal TBI PHY and external PHY does not
support in-band auto-negotation.
Previously, when configured for SGMII mode a TBI PHY would attempt to
restart auto-negotation during initializtion. This auto-negotation
between a TBI PHY and external PHY would fail and result in unusable
ethernet operation.
Forcing the TBI PHY and and external PHY to link at 1000Mbps full duplex
in SGMII mode resolves this issue of auto-negotation failing.
Note that 10Mbps and 100Mbps operation is still possible on the external
side of the external PHY even when SGMII is operating at 1000Mbps.
The SGMII interface still operates at 1000Mbps, but each byte of data
is repeated 100 or 10 times for 10/100Mbps and the external PHY handles
converting this data stream into proper 10/100Mbps signalling.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch turns off MAC address mismatch warning when
optional eeprom programmed with MAC address is not available.
In that case, smc911x's MAC address register has its default
value ff:ff:ff:ff:ff:ff and it's not a valid address. This
makes eth_initialize() show the warning which has no
meaningful information while environment variable ethaddr
overrides the address read from the register. If there's no
eeprom and the value of MAC address register is not valid
after initialization, dev->enetaddr had better not be updated
and maintain its initial value 00:00:00:00:00:00, which I
think is what eth_initialize() expects. This is not a bug fix.
Even without this patch, the driver works fine. It's just for
enhancing the way of displaying messages.
Signed-off-by: Seunghyeon Rhee <seunghyeon@lpmtec.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Building for a bf533-stamp ends up with this error:
smc91111_eeprom.o: In function `smc91111_eeprom':
examples/standalone/smc91111_eeprom.c:58: undefined reference to `memset'
make[2]: *** [smc91111_eeprom] Error 1
The new eth_struct definition means gcc has to zero out the structure on
the stack, and some gcc versions optimize this with an implicit call to
memset. So tweak the structure style to avoid that gcc feature.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
imximage.c: In function 'imximage_parse_cfg_file':
imximage.c:142: warning: implicit declaration of function 'getline'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a disable sub-command to the cpu command that allows for disabling
cores in multicore processors. This can be useful for systems that are
using multicore chips but aren't utilizing all the cores as a way to
reduce power and possibly improve performance.
Also updated an added missing copyright.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
imxtract currently can not handle compressed images. This patch adds
handling for bzip2 and zip compression. In both cases, a destination
address has to be specified for extraction.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
r14 is no longer used as non volatile GOT ptr. Instead
the volatile r12 is used so be sure to do GET_GOT in
asm code when you need to access global data.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
r14 is not supposed to be clobbered by functions. Switch
to r12 and call GET_GOT when needed. This will allow u-boot
to loose the -ffixed-r14 gcc option.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Using the GOT in IRQ handlers requires r14 to be -ffixed-r14.
Avoid this by relocatate transfer_to_handler too.
This will allow to free up r14 later on.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Since 1.0 and 2.0 use different snum table,
we fixup the snum value according to SPRN_SVR.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The real clock divider is 4 times of the bits LCRR[CLKDIV],
according the latest RevF RM.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix typo in SYSCTL_CLOCK_MASK, which caused residual in high bits of SDCLKFS.
Signed-off-by: Jin Qing <B24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit bc20f9a952.
The original code was correct. I clearly need glasses or a brown
paper bag.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The masks for MEM_PLL_RAT and SYS_PLL_RAT should have been 5-bits
instead of 4.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit b5b004ad8a caused the sector_size to
be calculated incorrectly when the part size was not hardcoded. This is
because the new code relied on part->size but tried to do the calculation
before it was initialized properly, and it did not take into consideration
the magic SIZE_REMAINING define.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
At least on OS X 10.5 and older, getline does not exist. So split out the
function from the mingw code so that we can pull it in for Darwin systems.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current libfdt object rules hard depend implicitly on the .depend file
being correct. If it isn't, then it is unable to properly compile the
objects. Give it a full path like all the other implicit rules here so it
will always work in face of .depend issues.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If you really want to slim down U-Boot and you would rather use a higher
compression scheme (like LZMA), it'd be nice to disable gzip/zlib since
these code bases take up a significant amount of space.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds support for "imximage" (MX Boot Image)
to the mkimage utility. The imximage is used on the Freescales's
MX.25, MX.35 and MX.51 processors.
Further details under doc/README.imximage.
This patch was tested on a Freescale mx51evk board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Content of the RSR is put into gd early so we can output it together
with the CPU info. The clearing of gd in board_init_f is redundant for
this architecture as it is done in cpu_init_f so we remove it.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Normally the processor clock has a divisor of 2.
In some cases this this needs to be set to 4.
Check the user has set environment mdiv to 4 to change the divisor.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
SPEAr320 SoC support contains basic spear320 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
- emi driver(cfi support)
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr310 SoC support contains basic spear310 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
- emi driver(cfi support)
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr310 and SPEAr320 SoCs contain an EMI controller to interface
Paraller NOR flashes. This patch adds the support for this IP
The standard CFI driver is used to interface with NOR flashes
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr300 SoC support contains basic spear300 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
Signed-off-by: Vipin <vipin.kumar@st.com>
This patch adds the support to read and write mac id from i2c
memory.
For reading:
if (env contains ethaddr)
pick env ethaddr
else
pick ethaddr from i2c memory
For writing:
chip_config ethaddr XX:XX:XX:XX:XX:XX writes the mac id
in i2c memory
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr600 SoC support contains basic spear600 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr SoCs contain a synopsys usb device controller.
USB Device IP can work in 2 modes
- DMA mode
- Slave mode
The driver adds support only for slave mode operation of usb
device IP. This driver is used along with standard USBTTY
driver to obtain a tty interface over USB on the host
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr SoCs contain an FSMC controller which can be used to interface
with a range of memories eg. NAND, SRAM, NOR.
Currently, this driver supports interfacing FSMC with NAND memories
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr SoCs contain a serial memory interface controller. This
controller is used to interface with spi based memories.
This patch adds the driver for this IP.
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr Architecture support added. It contains the support for
following SPEAr blocks
- Timer
- System controller
- Misc registers
Signed-off-by: Vipin <vipin.kumar@st.com>
