Since E1000 driver has been converted to driver model, enable it
on Intel Crown Bay. But the Intel Topcliff GbE driver has not been
converted to driver model yet, disable it for now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
So far we only enabled one legacy serial port on the SMSC LPC47m
superio chipset on Intel Crown Bay board. As the board also has
dual PS/2 ports routed out, enable the keyboard controller which
is i8042 compatible so that we can use PS/2 keyboard and mouse.
In order to make PS/2 keyboard work with the VGA console, remove
CONFIG_VGA_AS_SINGLE_DEVICE. To boot Linux kernel with PIC mode
using PIRQ routing table, adjust the mask in the device tree to
reserve irq12 which is used by PS/2 mouse.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It looks that x86 chipset always contains a host bridge at pci
b.d.f 0.0.0, so enable this for all boards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Move config for the E1000 Ethernet driver to Kconfig and tidy up affected
boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enable graphics support on Intel Crown Bay board With the help of
vgabios for Intel TunnelCreek IGD. Tested with an external LVDS
panel connected to X4 connector and SDVO adapter connected to X9
connector on the board.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some x86 boards set CONFIG_NR_DRAM_BANKS to 1, which causes incorrect
DRAM size printed when booting from coreboot, like this:
CPU: x86, vendor Intel, device 663h
DRAM: 636 KiB
Using default environment
Change it to 8 which should be enough for both coreboot and bare
cases, and move it to x86-common.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement Intel Queensbay platform-specific PIRQ routing support.
The chipset PIRQ routing setup is called in the arch_misc_init().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since all x86 boards use spi flash as its bootloader storage media,
it makes sense to make CONFIG_ENV_IS_IN_SPI_FLASH a common option.
So far only minnowmax board does not support it so undefine it in
its board configuration file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Crown Bay board has one ethernet port connected from Intel
Topcliff PCH. Enable it in the board configuration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Convert CONFIG_X86_RESET_VECTOR and CONFIG_SYS_X86_START16 to Kconfig
options so that we can remove them from board configuration file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are two standard SD card slots on the Crown Bay board, which
are connected to the Topcliff PCH SDIO controllers. Enable the SDHC
support so that we can use them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We don't have driver for the Intel Topcliff PCH Gigabit Ethernet
controller for now, so enable the Intle E1000 NIC support, which
can be plugged into any PCIe slot on the Crown Bay board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Crown Bay board has an SST25VF016B flash connected to the Tunnel
Creek processor SPI controller used as the BIOS media where U-Boot
is stored. Enable this flash support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>