Command calls update_tftp() analogous to automatic update described
in doc/README.update.
Usage:
fitupd [addr]
- run update from FIT image at addr
or from tftp 'updatefile'
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
P2041RDB Specification:
-----------------------
Memory subsystem:
* 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 256 Kbit M24256 I2C EEPROM
* 16 Mbyte SPI memory
* SD connector to interface with the SD memory card
Ethernet:
* dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
* dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
PCIe:
* Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
* Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
I2C:
* I2C1: Real time clock, Temperature sensor, Memory module
* I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Specify hwconfig usage for USB mode and phy change
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023RDS board is the reference board for the P1023 SoC.
Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe,
UART, I2C, etc.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Includes board config file, documentation, maintainer and boards.cfg
entries, and board specific files in vendor dir.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add another nand write. variant, trimffs. This command will request of
nand_write_skip_bad() that all trailing all-0xff pages will be
dropped from eraseblocks when they are written to flash as-per the
reccommended behaviour of the UBI FAQ [1].
The function that implements this timming is the drop_ffs() function
by Artem Bityutskiy, ported from the mtd-utils tree.
[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_flasher_algo
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Artem Bityutskiy <dedekind1@gmail.com>
CC: Detlev Zundel <dzu@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it. Drop it.
This includes support for VFD displays which have always been used by
this board only.
Signed-off-by: Wolfgang Denk <wd@denx.de>
When your emulator is connected at reset (or is used to load u-boot)
it is possible to get the relocation address from the gd->relocaddr
since gd is always in r8 (on ARM) it is addressable before the
gdb has remapped symbols.
Document this alternate method in-line with the original method
written by Heiko Schocher.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Heiko Schocher <hs@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
The bdinfo command prints the relocaddr on ARM as it does
on PPC.
Update the debugging instructions for arm relocation to
reflect this fact rather than requiring that the user
rebuild the u-boot image using -DDEBUG.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Wolfgang Denk <wd@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Add function video_get_video_mode(), which parses the "video-mode" environment
variable and returns each of its components. The format matches the video=
command-line option used for Linux:
video-mode=<driver>:<xres>x<yres>-<depth>@<freq><,option=string>
<driver> The video driver, ignored by U-Boot
<xres> The X resolution (in pixels) to use.
<yres> The Y resolution (in pixels) to use.
<depth> The color depth (in bits) to use.
<freq> The frequency (in Hz) to use.
<options> A comma-separated list of device-specific options
Signed-off-by: Timur Tabi <timur@freescale.com>
For soc which have pin multiplex relation, some of them can't enable
simultaneously. This patch add environment var 'hwconfig' content
defination for them. you can enable some one function by setting
environment var 'hwconfig' content and reset board. Detail setting
please refer doc/README.p1022ds
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add documentation for the "serdes" hwconfig option, which is used to
specify the status of SerDes banks two and three for the SERDES8 erratum
work-around.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Info about the hardware can be found here:
http://www.dilnetpc.com/dnp0086.htm
Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Purple SoC and eval board are not actively maintained since years.
This patch removes the support completely as aggreed with Wolfgang Denk.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
This adds support for using USB Ethernet dongles in host mode. This is just
the framework - drivers will come later. A new config option called
CONFIG_USB_HOST_ETHER can be defined in board config files to switch this
on.
The was originally written by NVIDIA and was cleaned up for release by the
Chromium authors.
Signed-off-by: Simon Glass <sjg@chromium.org>
The R0P7757LC0030RL board has SH7757, 256MB DDR3-SDRAM, SPI ROM,
Ethernet, and more.
This patch supports the following functions:
- 256MB DDR3-SDRAM
- SPI ROM
- Ethernet
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The patch adds suupport for the Freescale's mx35pdk board
(known as well as mx35_3stack).
The board boots from the NOR flash. Following devices
are supported:
- two ethernet devices (FEC and SMC911x on debug board)
- I2C
- PMIC (MC13892) via I2C interface
- UART
- NOR flash (64MB)
- NAND flash (2GB)
- basic access to mc9sdz60 registers via I2C interface
Signed-off-by: Stefano Babic <sbabic@denx.de>
This patch add the MX53 boot image support.
This patch has been tested on Freescale MX53EVK board
and MX51EVK board.
Signed-off-by: Jason Liu <r64343@freescale.com>
Added fsl_ddr_get_version() function to for DDR3 to poll DDRC IP version
(major, minor, errata) to determine if unique mode registers are available.
If true, always use unique mode registers. Dynamic ODT is enabled if needed.
The table is documented in doc/README.fsl-ddr. This function may also need
to be extend for future other platforms if such a feature exists.
Enable address parity and RCW by default for RDIMMs.
Change default output driver impedance from 34 ohm to 40ohm. Make it 34ohm for
quad-rank RDIMMs.
Use a formula to calculate rodt_on for timing_cfg_5.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add fsl_ddr:ecc=on in hwconfig. If ECC is enabled in board configuration file,
ECC can be turned on/off by this switch. If this switch is omitted, it is ON by
default.
Updated hwconfig calls to use local buffer.
Syntax is
hwconfig=fsl_ddr:ecc=on
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By default, "-" chars are interpreted as hyphens (U+2010) by groff, not
as minus signs (U+002D). Since options to programs use minus signs
(U+002D), this means for example in UTF-8 locales that you cannot cut
and paste options, nor search for them easily.
(Reported by lintian.)
Signed-off-by: Loc Minier <loic.minier@linaro.org>
difference to previous board version:
- M29W128GH flash from Numonyx
- SDRAM ISSI IS45S16800 (Option A2 105°C)
- rev5 uses RTC RV-3029-C2
- update cs0 and cs1 baseaddr and length
depending on the detected flash size.
- added Werner Pfister <Pfister_Werner@intercontrol.de>
as maintainer for the digsy board variants
- As the M29W128GH needs a special flash_cmd_reset()
document that in the new file doc/README.cfi.
- move "#endif /* CONFIG_CMD_IDE */" to the right place
- remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5
boards
- change doc/README.cfi as Stefan Roese suggested
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Wolfgang Denk <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Werner Pfister <Pfister_Werner@intercontrol.de>
cc: Detlev Zundel <dzu@denx.de>
This config option is for an erratum workaround; rename it to be more
clear. Also, drop it from config files don't need it and were
undefining it.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.
The following bootup procedure is used.
At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.
Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
u-boot.bin image to the RAM from u-boot, and flash to the nand flash
at address 0xe0000.
* hawkboard_nand_config - Used to generate the secondary
bootloader(nand_spl) image. This creates an elf file u-boot-spl
under nand_spl/. Create an AIS signed image using this file, and
flash it to the nand flash at address 0x20000. The ais file should
fit in one block.
* hawkboard_uart_config - This is same as the first image, but with
the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The barco board appears to be unmaintained since it was added about 5
years ago. The environment location has probably never been correct.
Drop it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Marc Leeman <marc.leeman@barco.com>
Acked-by: Stefan Roese <sr@denx.de>
The ERIC board appears to be unmaintained for more than 9 years. The
environment location has probably never been correct, and has been
definitely broken since for at least a year. Drop it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Swen Anderson <sand@peppercon.de>
Acked-by: Stefan Roese <sr@denx.de>
The TI DA850/OMAP-L138/AM18x EVM can be populated with devices
having different maximum allowed CPU clock rating.
The maximum clock the chip can support can only be determined from
the label on the package (not software readable).
Introduce a method to pass the maximum allowed clock rate information
to kernel using ATAG_REVISION. The kernel uses this information to
determine the maximum cpu clock rate reachable using cpufreq.
Note that U-Boot itself does not set the CPU clock rate. The CPU
clock is setup by a primary bootloader ("UBL"). The rate setup by
UBL could be different from the maximum clock rate supported by the
device.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The README.davinci in documentation folder is missing information
regarding DA850 which is a supported DaVinci device.
Add this information.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support. However, other recent changes led to a different
implementation (ELF relocation), where this no longer works. By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.
So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Add the ability to not report an I2C POST error for a set of given I2C
addresses on bootup. This is useful for cases when a device may or may
not be present, and neither case is considered an error. For example:
- Some form factors such as XMC and Compact PCI Express have an I2C
EEPROM whose address changes based on geographical address. Eg
installed in one slot its EEPROM address is, 0x50, in another its
0x51, etc. This allows multiple devices to have their EEPROMs present
on the same I2C bus. Thus the I2C devices present for an XMC or
CPCIe card depend on if and where other cards are installed in the
same system.
- Some cards have optional I2C devices. Eg one hardware build
configuration has different I2C devices than another and software
can't determine if the optional device should be present or not.
- Some cards have optional daughtercards with I2C devices on them.
- I2C EEPROMs address range depends on their size. Its possible to
support differently size EEPROMs by only probing the EEPROM's base
address and ignoring the other addresses that are impacted by its
size.
A new CONFIG_SYS_POST_I2C_IGNORES define has been added which specifies
a list of I2C addresses for the I2C POST to ignore.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The memory test is performed after DDR initialization when U-boot stills runs
in flash and cache. On recent mpc85xx platforms, the total memory can be more
than 2GB. To cover whole memory, it needs be mapped 2GB at a time using a
sliding TLB window. After the testing, DDR is remapped with up to 2GB memory
from the lowest address as normal.
If memory test fails, DDR DIMM SPD and DDR controller registers are dumped for
further debugging.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a document to maintain a list of boards removed from the current
source tree, so archeologists can check more easily if here is
something they might want to dig for...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Conflicts:
arch/arm/include/asm/config.h
board/LaCie/edminiv2/config.mk
board/karo/tx25/config.mk
board/logicpd/imx27lite/config.mk
doc/README.arm-relocation
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 14d0a02a "Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE" missed a
few places, especially for boards that were added inbetween. Fix the
remaining issues.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Clean up Makefile, and drop a lot of the config.mk files on the way.
We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
ELF relocation tables generated with linker option -pie can
be used to fixup code and data in a single loop at relocation,
removing the need for manual fixups anywhere else in the code.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Split the display command into generic interface and hardware-specific
realization for PDSP188x LED display found on hmi1001 and manroland
boards. Simple interface for LED displays is defined in
include/led-display.h and described in doc/README.LED_display.
Driver-specific implementation was moved into drivers/misc/pdsp188x.c
file (enabled with CONFIG_PDSP188x set).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
The Freescale P1022DS can use either a 12.288MHz or a 11.2896MHz reference
clock for the audio codec, but by default both are disabled. Add a 'audclk'
hwconfig option that allows the user to choose which clock he wants.
The 12.288MHz clock allows the codec to use sampling rates of 16, 24, 32, 48,
64, and 96KHz. The 11.2896 clock allows 14700, 22050, 29400, 44100, 58800, and
88200Hz.
Also configure a pin muxing to select some SSI signals, which will disable
I2C1.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Change the implementation for arm926 to relocate the code to
an arbitrary address in RAM.
Adapt the TX25 (i.MX25), magnesium board to test the changes.
On the tx25 board TEXT_BASE is set to the final relocation
address to prevent one more copying of u-boot code
when relocating. More info see:
doc/README.arm-relocation
da850 board:
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
!! This breaks support for all arm boards !!
To compile in old style, you must define
CONFIG_SYS_ARM_WITHOUT_RELOC or you can compile
with "CONFIG_SYS_ARM_WITHOUT_RELOC=1 ./MAKEALL board"
!! This define will be removed soon, so convert your
board to use relocation support
Portions of this work were supported by funding from
the CE Linux Forum.
Signed-off-by: Heiko Schocher <hs@denx.de>
Fix boot from NAND for non-ARM systems
Signed-off-by: Wolfgang Denk <wd@denx.de>
continuation of commit 2ecc2262d66a286e3aac79005bcb5f461312dea8
"net ppc: fix ethernet device names with spaces" (currently in
u-boot-net.git) for QE based parts.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
since commit 1384f3bb8a ethernet names
with spaces drop a
Warning: eth device name has a space!
message. This patch fix it for:
- "FEC ETHERNET" devices found on
mpc512x, mpc5xxx, mpc8xx and mpc8220 boards.
renamed to "FEC".
- "SCC ETHERNET" devices found on
mpc8xx, mpc82xx based boards. Renamed to "SCC".
- "HDLC ETHERNET" devices found on mpc8xx boards
Renamed to "HDLC"
- "FCC ETHERNET" devices found on mpc8260 and mpc85xx based
boards. Renamed to "FCC"
Tested on the kup4k board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Some Linux distributions include the "mkimage" as a package.
This commit provides a manual page for mkimage.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Added documentation for FIT images and examples.
Moved to doc/ directory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
CONFIG_IDE_SWAP_IO
This configuration option replaces a complex conditional
in cmd_ide.c with an explicit define to be added to SoC or
board configs.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Verified on MPC8641HPCN with four DDR2 dimms. Each dimm has dual
rank with 512MB each rank.
Also check dimm size and rank size for memory controller interleaving
Signed-off-by: York Sun <yorksun@freescale.com>
Replace environmental variables memctl_intlv_ctl and ba_intlv_ctl with
hwconfig parameters. The syntax is
setenv hwconfig "fsl_ddr:ctlr_intlv=<mode>,bank_intlv=<mode>"
The mode values for memory controller interleaving are
cacheline
page
bank
superbank
The mode values for bank interleaving are
cs0_cs1
cs2_cs3
cs0_cs1_and_cs2_cs3
cs0_cs1_cs2_cs3
Signed-off-by: York Sun <yorksun@freescale.com>
Designware network driver support added.
This is a Synopsys ethernet controller
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The "-ffixed-r15" option doesn't work well for gcc4. Since we
don't use gp for small data with option "-G0", we can use gp
as global data pointer. This allows compiler to use r15. It
is necessary for gcc4 to work properly.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Add a new function to the eth_device struct for programming a network
controller's hardware address.
After all network devices have been initialized and the proper MAC address
for each has been determined, make a device driver call to program the
address into the device. Only device instances with valid unicast addresses
will be programmed.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Tested-by: Prafulla Wadaskar <prafulla@marvell.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.
Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk
This change is intended to clean up the top-level directory structure
and more closely mimic Linux's directory organization.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The CPUDIR variable points to the location of a target's CPU directory.
Currently, it is set to cpu/$CPU. However, using $CPUDIR will allow for
more flexibility in the future. It lays the groundwork for reorganizing
U-Boot's directory structure to support a layout such as:
arch/$ARCH/cpu/$CPU/* (architecture with multiple CPU types)
arch/$ARCH/cpu/* (architecture with one CPU type)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
As this seems unclear, document how the flow of setting up
the MAC address is correct.
Signed-off-by: Heiko Schocher <hs@denx.de>
Text changed slightly, adding input from Mike Frysinger.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The ramdisk sections in doc/uImage.FIT/multi.its lack
load address and entry point properties. Using examples
from this file will result in unbootable image, u-boot
will issue the following error messages:
Can't get ramdisk subimage load address!
Ramdisk image is corrupt or invalid
This patch adds missing properties to ramdisk sections.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
The ml300 board has a number of issues, but nobody cares about this
long-orphaned board any more. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
This patch corrects small mistake in the register list in
doc/README.mpc8536ds. These registers are 32 bits and this one starts
at ....c not ....e
When using the ...c address I can boot from sd, when using the ...e
address I cannot.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Acked-by: Hu Mingkai <B21284@freescale.com>
* prepare joining at91 and at91rm9200
* add modified copy of soc files to cpu/arm920t/at91 to make
possible to compile at91rm9200 boards in at91 tree instead
of at91rm9200
* add header files with c structure defs for AT91 MC, ST and TC
* the new cpu files are using at91 c structure soc access
* please read README.soc-at91 for details
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
* add's the new temporary CONFIG_AT91_LEGACY to all board configs
This will need for backward compatiblity, while change the SoC access
to c structures. If CONFIG_AT91_LEGACY is defined, the deprecated
SoC is used.
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
This patch adds support for "imximage" (MX Boot Image)
to the mkimage utility. The imximage is used on the Freescales's
MX.25, MX.35 and MX.51 processors.
Further details under doc/README.imximage.
This patch was tested on a Freescale mx51evk board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The core support for NAND booting is there already, so this patch
is pretty straightforward.
There is one trick though: top level Makefile expects nand_spl to
be in nand_spl/board/$(BOARDDIR), but we can fully reuse the code
from mpc8313erdb boards, and so to not duplicate the code we just
symlink nand_spl/board/freescale/mpc8315erdb to mpc8313erdb.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
o silence make during ln echo
o update documentation
o and avoid:
$ ./MAKEALL MPC8315ERDB_NAND
Configuring for MPC8315ERDB board...
sdram.o: In function `fixed_sdram':
/home/r1aaha/git/u-boot/nand_spl/board/freescale/mpc8313erdb/sdram.c:72: undefined reference to `udelay'
by renaming udelay -> __udelay in the spirit of commit
3eb90bad65 "Generic udelay() with watchdog
support".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The example FIT image source files do not compile with the latest dtc and
mkimage. The following error message is produced:
DTC: dts->dtb on file "kernel.its"
Error: kernel.its 7:0 - 1:0 syntax error
FATAL ERROR: Unable to parse input tree
./mkimage: Can't read kernel.itb.tmp: Invalid argument
The FIT image source files are missing the "/dts-v1/;" directive at the
beginning of the file. Add the directive to the examples.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
The dev->halt() func can be called at any time, and the dev->recv() func
does not need to use NetRxPackets[] when calling NetReceive().
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Adds new board SMDKC100 that uses s5pc100 SoC
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
This feature is useful when your board uses different mii buses for different
phys and all (or a part) of these buses are implemented via bit-banging mode.
The driver requires that the following macros should be defined into the board
configuration file:
CONFIG_BITBANGMII - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support
If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs
to define at least the following macros:
MII_INIT - Generic code to enable the MII bus (optional)
MDIO_DECLARE - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ - Read the MDIO pin
MDIO(v) - Write v on the MDIO pin
MDC_DECLARE - Declaration needed to access to the MDC pin (optional)
MDC(v) - Write v on the MDC pin
The previous macros make the driver compatible with the previous version
(that didn't support the multi-bus).
When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill
the bb_miiphy_buses[] array with a record for each required bus and declare
the bb_miiphy_buses_num variable with the number of mii buses.
The record (struct bb_miiphy_bus) has the following fields/callbacks (see
miiphy.h for details):
char name[] - The symbolic name that must be equal to the MII bus
registered name
int (*init)() - Initialization function called at startup time (just
before the Ethernet initialization)
int (*mdio_active)() - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
int (*set_mdio)() - Write the MDIO pin
int (*get_mdio)() - Read the MDIO pin
int (*set_mdc)() - Write the MDC pin
int (*delay)() - Delay function
void *priv - Private data used by board specific code
The board code will look like:
struct bb_miiphy_bus bb_miiphy_buses[] = {
{ .name = miibus#1, .init = b1_init, .mdio_active = b1_mdio_active, ... },
{ .name = miibus#2, .init = b2_init, .mdio_active = b2_mdio_active, ... },
...
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
sizeof(bb_miiphy_buses[0]);
Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
As discussed on mailing list, <0 indicates failure, >=0 indicates number
of interfaces found.
Also added blurb about private data
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
By nature of being based off the MPC8548CDS board, this
board inherited an ENV_SIZE setting of 256k. But since
it has a smaller flash device (8MB soldered on), it has
a native sector size of 128k, and hence the ENV_SIZE was
causing 2 sectors to be used for the environment.
By removing the unused sector, we can push TEXT_BASE up
closer to the end of address space and reclaim that
sector for any other application. This also fixes the
mismatch between TEXT_BASE and MONITOR_LEN reported by
Kumar earlier.
Since this board also supports the ability to boot off
the 64MB SODIMM flash, this change is forward looking
with that in mind; i.e. the settings for MONITOR_LEN
and ENV_SIZE will work when the 512k sectors of the
SODIMM flash are used for alternate boot in the future.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The previous README.sbc8548 was pretty much content-free. Replace
it with something that actually gives the end user some relevant
hardware details, and also lists the u-boot configuration choices.
Also in the cosmetic department, fix the bogus line in the Makefile
that was carried over from the SBC8560 Makefile, and the typo in
the sbc8548.c copyright.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The more standard 'source' command provides identical functionality to
the autoscr command.
Environment variable names/values on the MVBC_P, MVBML7, kmeter1,
mgcoge, and km8xx boards are updated to no longer refernce 'autoscr'.
The 'autoscript' and 'autoscript_uname' environment variables are
also removed.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Heiko Schocher <hs@denx.de>
The standard netcat, while ubiquitous, doesn't handle broadcast udp packets
properly. The local ncb util does however. So if ncb can be located in
the standard locations, automatically use that instead.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds support for "kwbimage" (Kirkwood Boot Image)
image types to the mkimage code.
For details refer to docs/README.kwbimage
This patch is tested with Sheevaplug board
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Ron Lee <ron@debian.org>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Since the Blackfin ABI favors higher scratch registers by default, use the
last scratch register (P3) for global data rather than the first (P5).
This allows the compiler's register allocator to use higher number scratch
P registers, which in turn better matches the Blackfin instruction set,
which reduces the size of U-Boot by more than 1024 bytes...
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.
Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, which isn't really user friendly.
This adds the typical PCI make targets to the toplevel Makefile
in accordance with what is being done with other boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Up to this point in time, the sbc8349 board was storing the u-boot
image in flash 2x. One for the HRCW value at the beginning of
flash (0xff80_0000), and once close to the end of flash (0xfff8_0000)
for the actual image that got executed.
This moves the TEXT_BASE to be the beginning of flash, which makes
the second copy of the image redundant, and frees up the flash
from the end of the environment storage to the end of the flash
device itself.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds a new video driver
* adds common bus_vcxk framebuffer driver
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
[agust@denx.de: fixed lots of style issues before applying]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
On 04 Oct 2008 Pieter posted a dns implementation for U-Boot.
http://www.mail-archive.com/u-boot-users@lists.sourceforge.net/msg10216.html
>
> DNS can be enabled by setting CFG_CMD_DNS. After performing a query,
> the serverip environment var is updated.
>
> Probably there are some cosmetic issues with the patch. Unfortunatly I
> do not have the time to correct these. So if anybody else likes DNS
> support in U-Boot and has the time, feel free to patch it in the main tree.
Here it is again - slightly modified & smaller:
- update to 2009-06 (Pieter's patch was for U-Boot 1.2.0)
- README.dns is added
- syntax is changed (now takes a third option, the env var to store
the result in)
- add a random port() function in net.c
- sort Makefile in ./net/Makefile
- dns just returns unless a env var is given
- run through checkpatch, and clean up style issues
- remove packet from stack
- cleaned up some comments
- failure returns much faster (if server responds, don't wait for
timeout)
- use built in functions (memcpy) rather than byte copy.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Pieter Voorthuijsen <pieter.voorthuijsen@prodrive.nl>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Legacy NAND had been scheduled for removal. Any boards that use this
were already not building in the previous release due to an #error.
The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed. There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.
Signed-off-by: Scott Wood <scottwood@freescale.com>
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Remove CONFIG_SYS_DAVINCI_BROKEN_ECC option. It's not just nasty;
it's also unused by any current boards, and doesn't even match the
main U-Boot distributions from TI (which use soft ECC, or 4-bit ECC
on newer chips that support it).
DaVinci GIT kernels since 2.6.24, and mainline Linux since 2.6.30,
match non-BROKEN code paths for 1-bit HW ECC. The BROKEN code paths
do seem to partially match what MontaVista/TI kernels (4.0/2.6.10,
and 5.0/2.6.18) do ... but only for small pages. Large page support
is really broken (and it's unclear just what software it was trying
to match!), and the ECC layout was making three more bytes available
for use by filesystem (or whatever) code.
Since this option itself seems broken, remove it. Add a comment
about the MV/TI compat issue, and the most straightforward way to
address it (should someone really need to solve it).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
this will allow you to store use it for the env and to boot directly U-Boot from
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Using the example for reading a gpio, shows the problem.
NULL should be the gpio number.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Port version 2.6.27 of the linux kernel's omap gpio interface to u-boot.
The orignal source is in linux/arch/arm/plat-omap/gpio.c
See doc/README.omap3 for instructions on use.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This document describes the u-boot status LED API.
This allows common u-boot commands to use a board's leds to
provide status for activities like booting and downloading files.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop,
and isdram are no longer available so all references to them have been
updated to the new form of "i2c <cmd>".
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.
The functionality of the individual commands is still available via
the 'i2c' command.
This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This will make CONFIG_NET_MULTI the only net driver configuration and
we'll be able to remove this option.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Mflash is fusion memory device mainly targeted consumer eletronic and
mobile phone.
Internally, it have nand flash and other hardware logics and supports
some different operation (ATA, IO, XIP) modes.
IO mode is custom mode for the host that doesn't have IDE interface.
(Many mobile targeted SoC doesn't have IDE bus)
This driver support mflash IO mode.
Followings are brief descriptions about IO mode.
1. IO mode based on ATA protocol and uses some custom command. (read
confirm, write confirm)
2. IO mode uses SRAM bus interface.
Signed-off-by: unsik Kim <donari75@gmail.com>
Legacy NAND is marked for feature removal after April 2009 (i.e. this
upcoming release). There are still several boards that reference it
(though many do so only for disk-on-chip support which has been silently
disabled for a while now). These boards will now fail to build
with #error, though the code is still there if the user removes #error.
The plan is to remove the code outright in the next release, along with
any board code that refers to it (such as board/esd/common/auto_update.c).
Also, remove the legacy NAND API description from README.nand.
Signed-off-by: Scott Wood <scottwood@freescale.com>
According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.
This patch prepares this change and starts a 6 month transition
period as follows:
- The new "source" command has been added, which implements exactly
the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
have *not* been adapted yet; these will be renamed resp. removed in
a separate patch when the support for the "autoscr" command get's
finally dropped.
Signed-off-by: Wolfgang Denk <wd@denx.de>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
We can built 'make sh7785lcr_32bit_config'. And add new command "pmb"
for this mode. This command changes PMB for using 512MB system memory.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The new environment variable "korat_usbcf" selects the USB
port used by the Korat board's CompactFlash controller.
Signed-off-by: Larry Johnson <lrj@acm.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Add BeagleBoard support, common power code and README.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
The NMDK8815 board is distributed by ST Microelectornics.
Other (proprietary) code must be run to unlock the CPU before
U-Boot runs. doc/README.nmdk8815 outlines the boot sequence.
This is the initial port, with basic infrastructure and
a working serial port.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.
- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch will create a new board, SIMPC8313, from Sheldon Instruments. This
board boots from NAND devices and is configureable for either large or small
page devices. The board supports non-soldered DDR2, one ethernet port, a
Marvell 88E1118 PHY, and PCI host support. The board also has a FPGA connected
to the eLBC providing glue logic to a TMS320C67xx DSP.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define
#define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE
but that's bogus and did not work anyhow.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
At91sam9xe is basically an at91sam9260 with embedded flash. We can manage
it as another entry for at91sam9260 in the Makefile.
Check documentation at :
http://www.atmel.com/dyn/products/product_card.asp?part_id=4263
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
While the doc/README.NetConsole does have a snippet for people to
create their own netcat script, it's a lot easier to make a simple
dedicated script and tell people to use it.
Also spruce it up a bit to make it user friendly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Modifications to support console multiplexing. This is controlled using
CONFIG_SYS_CONSOLE_MUX in the board configuration file.
This allows a user to specify multiple console devices in the environment
with a command like this: setenv stdin serial,nc. As a result, the user can
enter text on both the serial and netconsole interfaces.
All devices - stdin, stdout and stderr - can be set in this manner.
1) common/iomux.c and include/iomux.h contain the environment setting
implementation.
2) doc/README.iomux contains a somewhat more detailed description.
3) The implementation in (1) is called from common/cmd_nvedit.c to
handle setenv and from common/console.c to handle initialization of
input/output devices at boot time.
4) common/console.c also contains the code needed to poll multiple console
devices for input and send output to all devices registered for output.
5) include/common.h includes iomux.h and common/Makefile generates iomux.o
when CONFIG_SYS_CONSOLE_MUX is set.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
This patch adds the possiblity to choose the media where the environment will
be located. This allow to choose this fundamental configuration without editing
config files.
Documentation file added.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Stelian Pop <stelian@popies.net>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds support for the kmeter1 board from Keymile,
based on a Freescale MPC8360 CPU.
- serial console on UART 1
- 256 MB DDR2 RAM
- 64 MB NOR Flash
- Ethernet RMII Mode over UCC4
- PHY SMSC LAN8700
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch creates a memory map with all the devices
in 36-bit physical space, in addition to the 32-bit map.
The CCSR relocation is moved (again, sorry) to
allow for the physical address to be 36 bits - this
requires translation to be enabled. With 36-bit physical
addressing enabled, we are no longer running with VA=PA
translations. This means we have to distinguish between
the two in the config file. The existing region name is
used to indicate the virtual address, and a _PHYS variety
is created to represent the physical address.
Large physical addressing is not enabled by default.
Set CONFIG_PHYS_64BIT in the config file to turn this on.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
The memory map on the 8641hpcn is modified to look more like
the 85xx boards; this is a step towards a more standardized
layout going forward. As part of this change, we now relocate
the flash.
The regions for some of the mappings were far larger than they
needed to be. I have reduced the mappings to match the
actual sizes supported by the hardware.
In addition I have removed the comments at the head
of the BAT blocks in the config file, rather than updating
them. These get horribly out of date, and it's a simple
matter to look at the defines to see what they are set to
since everything is right here in the same file.
Documentation has been changed to reflect the new map, as this
change is user visible, and affects the OS which runs post-uboot.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
* Check DDR interleaving mode from environment by reading memctl_intlv_ctl and
ba_intlv_ctl.
* Print DDR interleaving mode information
* Add doc/README.fsl-ddr to describe the interleaving setting
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
The auto-update feature allows to automatically download software updates
from a TFTP server and store them in Flash memory during boot. Updates are
contained in a FIT file and protected with SHA-1 checksum.
More detailed description can be found in doc/README.update.
Signed-off-by: Rafal Czubak <rcz@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
The i.MX31 has three SPI buses and each bus has several chip selects
and the MC13783 chip can be connected to any of these. The current
RTC driver for MC13783 is hardcoded for CSPI2/SS2.
This patch makes make MC13783 SPI bus and chip select configurable
via CONFIG_MC13783_SPI_BUS and CONFIG_MC13783_SPI_CS.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Based on original patch by Bernard Blackham <bernard@largestprime.net>
U-boot's HW ECC support for large page NAND on Davinci is completely
broken. Some kernels, such as the 2.6.10 one supported by
MontaVista for DaVinci, rely upon this broken behaviour as they
share the same code for ECCs. In the existing scheme, error
detection *might* work on large page, but error correction
definitely does not. Small page ECC correction works, but the
format is not compatible with the mainline git kernel.
This patch adds ECC code that matches what is currently in the
Davinci git repository (since NAND support was added in 2.6.24).
This makes the ECC and OOB layout written by u-boot compatible with
Linux for both small page and large page devices and fixes ECC
correction for large page devices.
The old behaviour can be restored by defining the macro
CFG_DAVINCI_BROKEN_ECC, which is undefined by default.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Pantelis Antoniou stated:
AFAIK, it is still used but the products using PPC are long gone.
Nuke it plz (from orbit).
So remove it since it cleans up a usage of env_get_char outside of
the environment code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Separate the portmux configuration functionality from the GPIO pin
control API.
- Separate the controller-specific code from the chip-specific code.
- Allow "ganged" port configuration (multiple pins at once).
- Add more flexibility to the "canned" peripheral select functions:
- Allow using more than 23 address bits, more chip selects, as
well as NAND- and CF-specific pins.
- Make the MACB SPEED pin optional, and choose between MII/RMII
using a parameter instead of an #ifdef.
- Make it possible to use other MMC slots than slot 0, and support
different MMC/SDCard data bus widths.
- Use more reasonable pull-up defaults; floating pins may consume a
lot of power.
- Get rid of some custom portmux code from the mimc200 board code. The
old gpio/portmux API couldn't really handle its requirements, but
the new one can.
- Add documentation.
The end result is slightly smaller code for all boards. Which isn't
really the point, but at least it isn't any larger.
This has been verified on ATSTK1002 and ATNGW100. I'd appreciate if
the board maintainers could help me test this on their boards. In
particular, the mimc200 port has lost a lot of code, so I'm hoping Mark
can help me out.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Mark Jackson <mpfj@mimc.co.uk>
Cc: Alex Raimondi <alex.raimondi@miromico.ch>
Cc: Julien May <julien.may@miromico.ch>
Changes since v1:
* Enable pullup on NWAIT
* Add missing include to portmux-pio.h
* Rename CONFIG_PIO2 -> CONFIG_PORTMUX_PIO to match docs
Remove some outdated and/or unnecessary information, and add updated
information about the toolchain and buildroot.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This board has SH7785, 512MB DDR2-SDRAM, NOR Flash,
Graphic, Ethernet, USB, SD, RTC, and I2C controller.
This patch supports the following functions:
- 128MB DDR2-SDRAM (29-bit address mode only)
- NOR Flash
- USB host
- Ethernet
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use of the non-skipping versions was almost always (if not always)
an error, and no valid use case has been identified.
Signed-off-by: Scott Wood <scottwood@freescale.com>
U-Boot allows for configurable prompt strings using the
CONFIG_AUTOBOOT_PROMPT resp. CONFIG_MENUPROMPT definitions. So far,
the assumption was that any such user defined problts would contain
exactly one "%d" format specifier. But some boards did not.
To allow for flexible boot prompts without adding too complex code we
now allow to specify the whole list of printf() arguments in the user
definition. This is powerful, but requires a responsible user who
really understands what he is doing, as he needs to know for exanple
which variables are available in the respective context.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The MVBC_P is a MPC5200B based camera system with Intel Gigabit ethernet
controller (using e1000) and custom Altera Cyclone-II FPGA on PCI.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add MPC8343 based board mvBlueLYNX-M7.
It's a single board stereo camera system.
Please read doc/README.mvblm7 for details.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
In case of several PCI USB controllers on a board this variable
specifys which controller to use.
See doc/README.generic_usb_ohci for details.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch fixes three typos.
The first is a repetition of CONFIG_CMD_BSP.
The second makes the #endif comment match its #if.
The third is a spelling error.
Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>
according to gvb's suggestion, polishing for the doc.
Signed-off-by: Jerry Van Baren <gerald.vanbaren@ge.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Renesas Solutions R7780MP is a reference board on SH7780.
This board has serial, 10/100 base Ethernet deivice, CF slot
and VGA devices. This board can set extension board.
Extension board has 10/100/1000 base Ethernet device, PCI slot,
S-ATA, iDVR slot.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch contains updates for changes for the Korat PPC440EPx board.
These changes include:
(1) Support for "permanent" and "upgradable" copies of U-Boot, as
described in the new "doc/README.korat" file;
(2) a new memory map for the registers in the board's CPLD;
(3) a revised format for manufacturer's data in serial EEPROM; and
(4) changes to track updates to U-Boot for the Sequoia board.
Signed-off-by: Larry Johnson <lrj@acm.org>
R29 was an unlucky choice as with recent toolchains (gcc-4.2.x) gcc
will refuse to use load/store multiple insns; instead, it issues a
list of simple load/store instructions upon function entry and exit,
resulting in bigger code size, which in turn makes the build for a
few boards fail.
Use r2 instead.
Signed-off-by: Wolfgang Denk <wd@denx.de>
MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
* TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
* load)
Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Marubun pcmcia is a chip for PCMCIA used with SuperH.
Of course, this can be used even by other architectures.
When use this driver, came to be able to use CompactFlash
and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Add support for Wind River's SBC8641D reference board.
Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Jon Loeliger <jdl@freescale.com>
Update the README for DDR ECC, change the name
to README.mpc83xx.ddrecc.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC8323E based board with 64MB fixed SDRAM, 16MB flash,
five 10/100 ethernet ports connected via an ICPlus IP175C
switch, one PCI slot, and serial. Features not supported
in this patch are SD card interface, 2 USB ports, and the
two phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When the rev2.x silicon mount on the MPC8360EMDS baord,
and if you are using the u-boot version after the commit
3fc0bd1591.
to make the ethernet interface usable, we have to setup
the jumpers correctly.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- now the Flash ST M29W040B is supported (not tested)
- fix the "led" command
- fix compile error, if BUILD_DIR is used
Signed-off-by: Heiko Schocher <hs@denx.de>
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This patch removes the CFG_PCI_PRE_INIT option completely, since
it's not needed anymore with the patch from Matthias Fuchs with
the "weak" pci_pre_init() implementation.
Signed-off-by: Stefan Roese <sr@denx.de>
e600 does not have a bootpg restriction.
Move the version string to beginning of image at fff00000.
Resetvec.S is not needed.
Update flash copy instructions.
Add tftpflash env variable
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Move the 8641HPCN's PIXIS code to the new directory
board/freescale/common/ as it will be shared by
future boards not in the same processor family.
Write a "pixis_reset" command that utilizes the FPGA
reset sequencer to support alternate soft-reset options
such as using the "alternate" flash bank, enabling
the watch dog, or choosing different CPU frequencies.
Add documentation for the pixis_reset to README.mpc8641hpcn.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Added information about usage of NetConsole on systems where the -l and -p
switches are mutually exclusive.
Signed-off-by: Igor Marnat <marny@rambler.ru>
Signed-off-by: Ben Warren <bwarren@qstreams.com>
Add support for the MPC8349E-mITX-GP, a stripped-down version of the
MPC8349E-mITX. Bonus features include support for low-boot (BMS bit in
HRCW is 0) for the ITX and a README for the ITX and the ITX-GP.
Signed-off-by: Timur Tabi <timur@freescale.com>
I've redone the SBC8349 support to match git-current, which
incorporates all the MPC834x updates from Freescale since the 1.1.6
release, including the DDR changes.
I've kept all the SBC8349 files as parallel as possible to the
MPC8349EMDS ones for ease of maintenance and to allow for easy
inspection of what was changed to support this board. Hence the SBC8349
U-Boot has FDT support and everything else that the MPC8349EMDS has.
Fortunately the Freescale updates added support for boards using CS0,
but I had to change spd_sdram.c to allow for board specific settings for
the sdram_clk_cntl (it is/was hard coded to zero, and that remains the
default if the board doesn't specify a value.)
Hopefully this should be mergeable as-is and require no whitespace
cleanups or similar, but if something doesn't measure up then let me
know and I'll fix it.
Thanks,
Paul.
The conflicts due to a new mpc7448 p3m7448 board is in the main tree.
Merge branch 'master' into hpc2
Conflicts:
MAKEALL
cpu/74xx_7xx/cpu.c
cpu/74xx_7xx/cpu_init.c
cpu/74xx_7xx/speed.c
(1) remove some C++ comments.
(2) remove trailing white space.
(3) remove trailing empty line.
(4) Indentation by table.
(5) remove {} in one line condition.
(6) add space before '(' in function call.
Remove some weird printf () output.
Add necessary comments.
Modified Makefile to support building in a separate directory.
chpart, nboot and NAND subsystem related commands now accept also partition
name to specify offset.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Patch by Haavard Skinnemoen, 6 Sep 2006 16:23:02 +0200
This patch adds common infrastructure code for the Atmel AVR32
architecture. See doc/README.AVR32 for details.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
- JFFS2 related commands implemented in mtd-utils style
- Support for bad blocks
- Bad block testing commands
- NAND lock commands
Please take a look at doc/README.nand for more details
Patch by Guido Classen, 10 Oct 2006
- Add support for PPC440EPx & PPC440GRx
- Add support for PPC440EP(x)/GR(x) NAND controller
in cpu/ppc4xx directory
- Add NAND boot functionality for Sequoia board,
please see doc/README.nand-boot-ppc440 for details
- This Sequoia NAND image doesn't support environment
in NAND for now. This will be added in a short while.
Patch by Stefan Roese, 07 Sep 2006
* Added comments and a printf to warn that PCI-X won't
work at 33MHz
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
AMCC suggested to set the PMU bit to 0 for best performace on
the PPC440 DDR controller.
Please see doc/README.440-DDR-performance for details.
Patch by Stefan Roese, 28 Jul 2006
Patch by Martin Krause, 8 Jun 2006
This patch supports two serial consoles on boards with
a MPC5xxx CPU. The console can be switched at runtime
by setting stdin, stdout and stderr to the desired serial
interface (serial0 or serial1). The PSCs to be used as
console port are definded by CONFIG_PSC_CONSOLE
and CONFIG_PSC_CONSOLE2.
See README.serial_multi for details.
relocate ichache_State to ram
u-boot can run from internal flash
Add EB+MCF-EV123 board support.
Add m68k Boards to MAKEALL
Patch from Jens Scharsig, 08 Aug 2005
Correct addessing errors in platform files.
Split off common core module data from Integrator header files to
include/armcoremodule.h.
Patch by Peter Pearse, 04 Oct 2005
Implemented support for MPC8548CDS board.
Added DDR II support based on SPD values for MPC85xx boards.
This roll-up patch also includes bugfies for the previously
published patches:
DDRII CPO, pre eTSEC, 8548 LBIU, Andy's TSEC, eTSEC 3&4 I/O
- Convert the CPM2 based functionality to use new CONFIG_CPM2
option rather than a myriad of CONFIG_MPC8560-like variants.
Applies to MPC85xx and MPC8260 boards, includes stxgp3 and sbc8560.
Eliminates the CONFIG_MPC8560 option entirely. Distributes the
new CONFIG_CPM2 option to each 8260 board.
Updates for OCOTEA board:
- Changed U-Boot size from 512kByte to 256kByte
- Fixed flash driver to support boot from soldered user flash
- Added README for switch from PIBS firmware to U-Boot
Add call to eth_halt() in net/net.c when called functions fail
after eth_init() has been called.
* Patch by Sam Song, 3 April 2005:
- Update README.Netconsole
- Update README
add SNTP support and expand time server and time offset fields of
DHCP support. See doc/README.SNTP
* Patch by Steven Scholz, 13 Dec 2004:
Fix bug in at91rm920 ethernet driver
add support for the TI OMAP2420 processor and its H4 reference
board
* Patch by Christian Pellegrin, 24 Sep 2004:
Added support for NE2000 compatible (DP8390, DP83902) NICs.
- Add support to revA version of PQ27 and PQ27E.
- Reverted MPC8260ADS baudrate back to original 115200
* Patch by Hojin, 17 Sep 2004:
Fix typo in cfi_flash.c
* Patch by Mark Jonas, 09 September 2004:
mtest's data line test (with CFG_ALT_MEMTEST set) returned a wrong
error message
* Patch by Mark Jonas, 31 August 2004:
Added option CFG_XLB_PIPELINING to enable XLB pipelining. This
improves FTP performance for MPC5200 systems. Enabled for IceCube
by default.
- Improve platform.S code for omap1510inn that detects whether code
is running from SDRAM or not. Patch allows SDRAM to be configured
if code is running out of SRAM at 0x20000000.
* Patch by Frederick Klatt, 30 Aug 2004:
Add support for the Wind River SBC8540/SBC8560 boards
- Introducing the concept of SoCs "./cpu/$(CPU)/$(SOC)"
- creating subdirs for SoCs ./cpu/arm920t/imx and ./cpu/arm920t/s3c24x0
- moving SoC specific code out of cpu/arm920t/ into cpu/arm920t/$(SOC)/
- moving drivers/s3c24x0_i2c.c and drivers/serial_imx.c out of drivers/
into cpu/arm920t/$(SOC)/
Allow clock setting on MPC866/MPC885 series chips according to
environment variable `cpuclk'
* Patch by Yuli Barcohen, 20 Apr 2004:
Remove unnecessary redefine of CPM_DATAONLY_SIZE for MPC826x
Update etags build target
* Improve NetConsole support: add support for broadcast destination
address and buffered input.
* Cleanup compiler warnings for GCC 3.3.x and later
* Fix problem in cmd_jffs2.c introduced by CFG_JFFS_SINGLE_PART patch
- support larger DDR memories up to 2G on the PC8540/8560ADS and
STXGP3 boards
- Made MPC8540/8560ADS be 33Mhz PCI by default.
- Removed moldy CONFIG_RAM_AS_FLASH, CFG_FLASH_PORT_WIDTH_16
and CONFIG_L2_INIT_RAM options.
- Refactor Local Bus initialization out of SDRAM setup.
- Re-implement new version of LBC11/DDR11 errata workarounds.
- Moved board specific PCI init parts out of CPU directory.
- Added TLB entry for PCI-1 IO Memory
- Updated README.mpc85xxads
* Patch by Sascha Hauer, 28 Jun:
- add generic support for Motorola i.MX architecture
- add support for mx1ads, mx1fs2 and scb9328 boards
* Patches by Marc Leeman, 23 Jul 2004:
- Add define for the PCI/Memory Buffer Configuration Register
- corrected comments in cpu/mpc824x/cpu_init.c
* Add support for multiple serial interfaces
(for example to allow modem dial-in / dial-out)
Add support for WindRiver's SBC8560 board
* Patch by Nicolas Lacressonniere, 24 Jun 2004
Small Bugs fixes for "at91rm9200dk" board:
- Timing modifications for SPI DataFlash access
- Fix NAND flash detection bug
* Patch by Nicolas Lacressonniere, 24 Jun 2004:
Add Support for Flash AT49BV6416 for AT91RM9200DK board
Completion of the 8540ADS/8560ADS updates:
Fix some PCI and Rapid I/O memory maps,
Initialize both TSEC 1 and 2,
Initialize SDRAM
Update MAINTAINER for 85xx boards and README.mpc85xxads
- Add support for the Logic Zoom LH7A40x based SDK board(s),
specifically the LPD7A400.
* Patches by Robert Schwebel, 15 May 2004:
- call MAC address reading code also for SMSC91C111;
- make SMSC91C111 timeout configurable, remove duplicate code
- fix get_timer() for PXA
- update doc/README.JFFS2
- use "bootfile" env variable also for jffs2
Add support for OMAP730 Perseus2 Development board
* Patch by Alan J. Luse, 29 Apr 2004:
Fix flash chip-select (OR0) option register setting on FADS boards.
* Patch by Alan J. Luse, 29 Apr 2004:
Report MII network speed and duplex setting properly when
auto-negotiate is not enabled.
* Patch by Jarrett Redd, 29 Apr 2004:
Fix hang on reset on Ocotea board due to flash in wrong mode.
- Add support for the SSV ADNP/ESC1 (Nios Softcore)
* Patch by George G. Davis, 9 Mar 2004:
fix recent build failure for SA1100 target
* Patch by Travis Sawyer, 09 Mar 2004:
Support native interrupt mode for the IBM440GX.
Previously it was running in 440GP compatibility mode.
Fix problems with GCC 3.3.x which changed handling of global
variables explicitly initialized to zero (now in .bss instead of
.data as before).
* Patch by Leon Kukovec, 02 Mar 2004:
add strswab() to fix IDE LBA capacity, firmware and model numbers
on little endian machines
* Patch by Masami Komiya, 02 Mar 2004:
- Remove get_ticks() from NFS code
- Add verification of RPC transaction ID
* Patch by Pierre Aubert, 02 Mar 2004:
cleanup for IDE and USB drivers for MPC5200
NS9750 DevBoard added
* Patch by Pierre AUBERT, 24 Feb 2004
add USB support for MPC5200
* Patch by Steven Scholz, 24 Feb 2004:
- fix MII commands to use values from last command
* Patch by Torsten Demke, 24 Feb 2004:
Add support for the eXalion platform (SPSW-8240, F-30, F-300)
Add support for the Xilinx ML300 platform
* Patch by Stephan Linz, 17 Feb 2004:
Fix watchdog support for NIOS
* Patch by Josh Fryman, 16 Feb 2004:
Fix byte-swapping for cfi_flash.c for different bus widths
* Patch by Jon Diekema, 14 Jeb 2004:
Remove duplicate "FPGA Support" notes from the README file
- update board/emk tree; use common flash driver
- Corrected tested bits in machine check exception in cpu/mpc5xxx/traps.c
[adapted for other PPC CPUs -- wd]
- Added support for the M48T08 on the EVAL5200 board in rtc/mk48t59.c
* Patch by Jon Diekema, 13 Feb 2004:
Call show_boot_progress() whenever POST "FAILED" is printed.
* Patch by Nishant Kamat, 13 Feb 2004:
Add support for TI OMAP1610 H2 Board
Fixes for cpu/arm926ejs/interrupt.c
(based on Richard Woodruff's patch for arm925, 16 Oct 03)
Fix for a timer bug in OMAP1610 Innovator
Add support for CS0 (ROM)/CS3 (Flash) boot in OMAP1610 Innovator and H2
* Patches by Stephan Linz, 12 Feb 2004:
- add support for NIOS timer with variable period preload counter value
- prepare POST framework support for NIOS targets
* Patch by Denis Peter, 11 Feb 2004:
add POST support for the MIP405 board
Add support for NET+50 CPU and ModNET50 board
* Patch by Sam Song, 10 Feb 2004:
Fix typos in cfi_flash.c
* Patch by Leon Kukovec, 10 Feb 2004
Fixed long dir entry slot id calculation in get_vfatname
* Patch by Robin Gilks, 10 Feb 2004:
add "itest" command (operators: -eq, -ne, -lt, -gt, -le, -ge, ==,
!=, <>, <, >, <=, >=)