When the Zynq Boot ROM code loads the payload from QSPI it uses the
LQSPI feature of the QSPI device, however it does not clean up its
configuration before handing over to the payload which leaves the device
confgured to by-pass the standard non-linear operating mode.
This ensures the Linear QSPI mode is disabled before re-enabling the
device.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We don't disable unused FM1-DTSEC1 MAC node in FMAN v2 since it is
used by MDIO. For FMAN v3, MDIO uses dedicated controller, so we
can disable unused FM1-DTSEC1 MAC node to avoid being probed in
Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: revised commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
Remove verbose message for FMan port.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
[York Sun: Added commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
The MC version numbers provide no meaningful information
about binary interface compatibility, so remove the
check which refuses to start the MC unless a specific
version is found.
Version checking is supposed to be done at the individual
object level, and individual drivers are responsible
for their own version checking.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For Setting and clearing the bits in SEC Block registers
sec_clrbits32() and sec_setbits32() are used which work as
per endianness of CAAM block.
So these must be used with SEC register address as argument.
If the value is read in a local variable, then the functions
will not behave correctly where endianness of CAAM and core is
different.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
CC: Alex Porosanu <alexandru.porosanu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When reading a large blob. e.g. a linux kernel (several MiBs) a watchdog
timeout might occur meanwhile. So pet the watchdog while operating on
the flash.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As the errata A008336 and A008514 do not apply to all LS series SoCs
(such as LS1021A, LS1043A) we move them to an soc specific file
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
With gcc-5.x we get a warning about the ambiguity of BUG_ON(!a != b) and
becomes BUG_ON((!a) != b). In this case reading of the function leads to
us wanting to rewrite this as BUG_ON(a != b).
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Cc: Haiying Wang <Haiying.Wang@freescale.com>
Cc: Roy Pledge <Roy.Pledge@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0,
T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on
LS102x Rev2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.
Signed-off-by: York Sun <yorksun@freescale.com>
The workaround requires different setting for range 1 vs 2.
Also adjust timeout value for waiting for controller to be idle.
Signed-off-by: York Sun <yorksun@freescale.com>
There is no sprintf implementation in tiny-printf, so don't try to use
it when tiny-printf if used.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Add xlnx,xps-spi-2.00.a/b which is compatible string
listed in the Linux kernel.
Remove origin one which has no real background.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Since all spi-flash core operations are moved into
sf_ops.c then it's better to renamed as spi-flash.c
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Used static for file-scope functions in sf_probe.c
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since spi_slave is a spi pointer in spi_flash{} then assign
spi_slave{} pointer to flash->spi and remove spi_slave
pointer argument to
- spi_flash_probe_slave
- spi_flash_scan
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
For assigning read_bar commands in spansion case, break
is missing this patch add that break.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
SST parts added on sf_params.c supports both SST_WR which consits
of both BP and WP and there is a spi controller ich which supports
only BP so the relevent _write hook set based on "slave->op_mode_tx"
hence there is no respective change required from flash side hance
removed these.
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Removed unneeded header includes in sf_ops and sf_probe
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Using macro's for flash power up read-only access code
leads wrong behaviour hence use idcode0 for runtime
detection, hence the flash which require this functionality
gets detected at runtime.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Most of the register access function are static,
so used simple name to represent each.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This patch removes unneeded ifdef and fixed accordingly.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Use static for file-scope functions and removed
them from header files.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
- Move bar read code below the bar write hance both
at once place, hence it easy for #ifdef macro only
once and readable.
- Move read_cmd_array at top
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
read_id code is related to spi_flash stuff
hence moved to sf_ops.
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Intension is that sf_ops should deals all spi_flash
related stuff and sf_probe (which should renamed future)
should be an interface layer for spi_flash versus spi drivers.
sf_ops => spi_flash interface
sf_probe => interface layer vs spi_flash(sf_probe) to spi drivers
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Rename spi_flash_validate_params to spi_flash_scan
as this code not only deals with params setup but
also configure all spi_flash attributes.
And also moved all flash related code into
spi_flash_scan for future functionality addition.
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Extend compatible list table for cdns,spi-r1p6 compatible string.
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPI_3WIRE is spi mode not spi flags, so this patch fixed
the spi-3wire checking throgh mode instead of flags.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
spi-3wire is used when SI/SO signals shared so get
the same from dts node and assign to mode on slave
plat->mode.
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Fix incorrect comment alignments.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a remark about SPL to this Kconfig option. Otherwise its identitcal
to the non-SPL version, which is confusing.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
AXP818 is rsb based PMIC and used on Allwinner A83T H8 Homlet dev board.
It's registers are different and calculating reg config is different than
that of earlier axp power ICs.
DCDC1, DCDC2, DCDC3 and DCDC5 is implemented at the moment.
all other voltages can be added subsequently.
AXP datasheet is uploaded to wiki:
http://linux-sunxi.org/File:AXP818_datasheet_Revision1.0.pdf
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These are currently dead codes. Until we have complete ACPI support,
we don't know if it works or not. Remove to avoid confusion.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Right now i8254_init() is called from timer_init() in the tsc timer
driver. But actually i8254 and tsc are completely different things.
Since tsc timer has been converted to driver model, we should find
a new place that is appropriate for U-Boot to call i8254_init(),
which is now x86_cpu_init_f().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This option is needed for all SoCs which have nodes on bus. Without
enabling this drivers are not found and probed.
Issue was found on Zynq MMC probe.
Enable this option by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
