Let's enable CONFIG_SYS_GENERIC_BOARD in order to get rid of warnings related
to generic board not being supported.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We should not hardcode CONFIG_NETMASK in the config file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
commit d6d07a9b... arm: vf610: add NAND support for vf610twr
generates the following warnings:
WARNING: no status info for 'vf610twr_nand'
WARNING: no maintainers for 'vf610twr_nand'WARNING: no status info for
'vf610twr_nand'
This is due to the fact that vf610twr_nand_defconfig has no Maintainer.
This patch proposed Alison as Maintainer and fix it.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Alison Wang <b18965@freescale.com>
CC: Stefan Agner <stefan@agner.ch>
i2c_pad_info1 is only used locally, so it can be made static.
Fix the following sparse warning:
board/freescale/mx6sxsabresd/mx6sxsabresd.c:160:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Define CONFIG_SYS_FSL_ESDHC_ADDR using USDHC4_BASE_ADDR.
USDHC3 and USDHC4 are both initialized in board_mmc_init. There is
no restriction on USDHC3 addr or USDHC4 addr should be assigned to
CONFIG_SYS_FSL_ESDHC_ADDR. So, just choose USDHC4_BASE_ADDR to avoid
errors when fsl_esdhc_mmc_init is invoked.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Define CONFIG_SYS_FSL_ESDHC_ADDR using USDHC4_BASE_ADDR which is used
in board_mmc_init.
If board_mmc_init failed, cpu_mmc_init->fsl_esdhc_mmc_init will use
CONFIG_SYS_FSL_ESDHC_ADDR to initialize sdhc. So set this macro to
correct value.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
This adds NAND support for the Vybrid tower system (TWR-VF65GS10)
provided by the vf610_nfc driver. Full 16-Bit bus width is
supported. Also an aditional config vf610twr_nand is introduced
which gets the environment from NAND. However, booting U-Boot from
NAND is not yet possible due to missing boot configuration block
(BCB).
Signed-off-by: Stefan Agner <stefan@agner.ch>
This adds initial support for Freescale NFC (NAND Flash Controller)
found in ARM Vybrid SoC's, Power Architecture MPC5125 and others.
The driver is called vf610_nfc since this is the first supported
and tested hardware platform supported by the driver.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
This patch moves mx35 to the common timer functions added in commit
8dfafdd - Introduce common timer functions <Rob Herring>
The (removed) mx35 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks(). get_ticks() returned a 32-bit value
cast up to a 64-bit value. If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor. Rather than patch the specific mx35 issues, simply
move everything over to the common code.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This patch moves mx31 to the common timer functions added in commit
8dfafdd - Introduce common timer functions <Rob Herring>
The (removed) mx31 timer code (specifically __udelay()) could deadlock at
the 32-bit boundary of get_ticks(). get_ticks() returned a 32-bit value
cast up to a 64-bit value. If get_ticks() + tmo in __udelay() crossed
the 32-bit boundary, the while condition became unconditionally true and
locks the processor. Rather than patch the specific mx31 issues, simply
move everything over to the common code.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Helmut Raiger <helmut.raiger@hale.at>
The boards using CONFIG_SYS_DV_NOR_BOOT_CFG (i.e. calimain,
da850evm_direct_nor and enbw_cmc) had the _start symbol defined after
the CONFIG_SYS_DV_NOR_BOOT_CFG word rather than before it in
arch/arm/lib/vectors.S. Because of that, if by lack of luck
'gd->mon_len = (ulong)&__bss_end - (ulong)_start' (see setup_mon_len())
was a multiple of 4 kiB (see reserve_uboot()), then the last BSS word
overlapped the first word of the following reserved RAM area (or went
beyond the top of RAM without such an area) after relocation because
__image_copy_start did not match _start (see relocate_code()).
This was broken by commit 41623c9 'arm: move exception handling out of
start.S files', which defined _start twice (before and after the
CONFIG_SYS_DV_NOR_BOOT_CFG word), then by commit 0a26e1d 'arm: fix a
double-definition error of _start symbol', which kept the definition of
the _start symbol after the CONFIG_SYS_DV_NOR_BOOT_CFG word. This new
commit fixes this issue by restoring the original behavior, i.e. by
defining the _start symbol before the CONFIG_SYS_DV_NOR_BOOT_CFG word.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Some boards, like mx31pdk and tx25, require the beginning of the SPL
code to be position-independent. For these two boards, this is because
they use the i.MX external NAND boot, which starts by executing the
first NAND Flash page from the NFC page buffer. The SPL then needs to
copy itself to its actual link address in order to free the NFC page
buffer and use it to load the non-SPL image from Flash before running
it. This means that the SPL runtime address differs from its link
address between the reset and the initial copy performed by
board_init_f(), so this part of the SPL binary must be
position-independent.
This requirement was broken by commit 41623c9 'arm: move exception
handling out of start.S files', which used an absolute address to branch
to the reset routine. This new commit restores the original behavior,
which just performed a relative branch. This fixes the boot of mx31pdk
and tx25.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reported-by: Helmut Raiger <helmut.raiger@hale.at>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: John Rigby <jcrigby@gmail.com>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
In commit 021e79c853 ("tools: imximage: Fix the maximum DCD size for
mx53/mx6") we have fixed the maximum DCD size for mx53/mx53.
Do the same on the README document for consistency.
Reported-by: Jonas Karlsson <jonas.d.karlsson@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Commit 224beb833e add clock
enabling function for FEC, but the masks are not available
for SX processor and the mx6sxsabresd cannot be built clean.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
Since the host compiler might not be gcc but e.g. clang
default to cc/c++ to invoke it.
cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
cc: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Commit fa9c021632 ("mx6: add example DTB for mx6qsabreauto") introduced
'imx6q-sabreauto.dts' but it adds no real value as the dts file only contains
the 'model' and 'compatible' strings.
After this commit the final binary is also changed from 'u-boot.imx' to
'u-boot-dtb.imx', which may confuse users.
So revert it until a more complete and useful device tree could be provided.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
nitrogen6x.h file defines CONFIG_CMD_FS_GENERIC, so we are able to use generic
'load' command instead of 'fatload'. It allows to use ext filesystem and keep
compatibilty with fat filesystem.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Stefano Babic <sbabic@denx.de>
Acked-By: Eric Nelson <eric.nelson@boundarydevices.com>
Currently mx6dlsabresd shares the same DCD settings with the nitrogen board.
Provide a DCD configuration file specific to mx6dlsabresd with the settings
recommended by the Freescale hardware team.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
UART does not use the UART FIFO, but we should also not rely that
the UART FIFO is diabled by default. For instance, when loading
U-Boot using the boot ROMs serial downloader protocol over UART,
FIFO is enabled at U-Boot start time.
This patch disables the RX and TX FIFO, sets back their thresholds
and flushes them.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The status register 1 (S1) is not writeable, hence we should not
write it. In order to clear the RDRF flag we only need to read
the data register.
Also, when stressing U-Boot a lot with serial input, an overflow can
occur which asserts the S1_OR flag (while not asserting the S1_RDRF
flag). To clear this flag we again just need to read the data
register, hence add this flag to the abort conditions for the while
loop.
Insert a compiler barrier to make sure reading the data register
gets executed after reading the status register.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The load region size of EIM-NOR are defined to 0. For this case,
the parameter "imximage_init_loadsize" must be calculated.
The imximage tool implements the calculation in the "imximage_generate"
function, but the following function "imximage_set_header" resets the value
and not calculate. This bug cause some fields of IVT head are not
correct, for example the boot_data and DCD overlay the application area.
Signed-off-by: Ye.Li <B37916@freescale.com>
The Latency parameters of PL310 Tag RAM latency control register and
Data RAM Latency control register are set in L2 cache enable. And
setting these registers must have PL310 NOT enabled.
But when using Plugin mode boot, the PL310 is enabled by bootrom.
The patch disables the PL310 before applying this setting.
Signed-off-by: Ye.Li <Ye.Li@freescale.com>
The leds array within struct ventana has space for 3 elements, but the
setup_board_gpio() function tries to set up 4 GPIOs for LEDs. Recent
versions of GCC complain about that:
board/gateworks/gw_ventana/gw_ventana.c: In function 'setup_board_gpio':
board/gateworks/gw_ventana/gw_ventana.c:987:27: warning: iteration 3u invokes undefined behavior [-Waggressive-loop-optimizations]
if (gpio_cfg[board].leds[i])
^
board/gateworks/gw_ventana/gw_ventana.c:986:2: note: containing loop
for (i = 0; i < 4; i++) {
^
Fix this by making the upper bound of the loop match the array size.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
According to mx53 and mx6 reference manuals:
"The maximum size of the DCD limited to 1768 bytes."
As each DCD entry consists of 8 bytes, we have a total of 1768 / 8 = 221, and
excluding the first entry, which is the header leads to 220 as the maximum
number for DCD size.
Reported-by: Jonas Karlsson <jonas.d.karlsson@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nitin Garg <nitin.garg@freescale.com>
Acked-by: Nitin Garg <nitin.garg@freescale.com>
Most Gateworks Ventana boards use a PLX PEX860x PCIe switch for PCIe expansion.
These boards use GPIO on the PLX device as PERST# for the downstream ports
thus we assert this when the PLX is enumerated.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for SATA.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Use Compulab eeprom module to obtain revision number, serial number, and
mac address from the EEPROM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add support for all 3 I2C busses on Compulab CM-FX6 CoM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add USB and USB OTG host support for Compulab CM-FX6 CoM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add ethernet support for Compulab CM-FX6 CoM
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add initial support for Compulab CM-FX6 CoM.
Support includes MMC, SPI flash, and SPL with dynamic DRAM detection.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Current way of calculation CS0_END field for MMDCx_MDASP register
is problematic because in most cases the user is forced to define
cs_density in an unnatural way: as value - 2, instead of value.
This breaks the abstraction provided by struct mx6_ddr_sysinfo
because the user is forced to be aware of the way the calculation
is performed.
Refactor the calculation.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
According to MX6 TRM, both MMDC and DRAM should be configured to
the same powerdown precharge. Currently, mx6_dram_cfg()
configures MMDC for fast pd (MDPDC[7] = 0), and the DRAM for
'slow exit (DLL off)' (MR0[12] = 0).
Configure MMDC for slow pd.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Bit 16 in mapsr register is in a reserved field. Don't write to it.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add macro which defines i2c_pads_info structs for multiple SoC types,
and a macro which selects the appropriate struct based on CPU type,
thus eliminating the need to manage multiple i2c pad configurations
manually when supporting multiple SoC types.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
