This patch fixes 2 problems with FDT EBC mappings on Canyonlands.
First, NAND EBC mapping was missing, making Linux NAND driver
unusable on this board. Second, NOR remapping code assumed that
NOR is always on CS0, however when booting from NAND NOR is on CS3.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently, when booting from NAND using nand_spl, in the beginning the default
environment is used until later in boot process the dynamic environment is read
out. This way environment variables that must be interpreted early, like the
baudrate or "silent", cannot be modified dynamically and remain at their
default values. Fix this problem by reading out main and redundand (if used)
copies of the environment in the nand_spl code.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
nand_util currently uses size_t which is arch dependent and not always a
unsigned long. Now use loff_t, as does the linux mtd layer.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The BF537-STAMP Blackfin board had a driver for working with NAND devices
that are simply memory mapped. Since there is nothing Blackfin specific
about this, generalize the driver a bit so that everyone can leverage it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Update chipselect handling in davinci_nand.c so that it can
handle 2 GByte chips the same way Linux does: as one device,
even though it has two halves with independent chip selects.
For such chips the "nand info" command reports:
Device 0: 2x nand0, sector size 128 KiB
Switch to use the default chipselect function unless the board
really needs its own. The logic for the Sonata board moves out
of the driver into board-specific code. (Which doesn't affect
current build breakage if its NAND support is enabled...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
All DaVinci SOC's use a CLE mask of 0x10 and an ALE mask of 0x8
except the DM646x. This was decided by the design team driving the design.
This patch updates the CLE and ALE values for DM646x.
Updated patches for DM646x will be sent shortly.
This applies to u-boot-nand-flash git
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The ALE mask used by DaVinci SOCs is wrong. The patch changes the mask value
from '0xa' to '0x8'. This is the mask we use for all TI releases.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Remove CONFIG_SYS_DAVINCI_BROKEN_ECC option. It's not just nasty;
it's also unused by any current boards, and doesn't even match the
main U-Boot distributions from TI (which use soft ECC, or 4-bit ECC
on newer chips that support it).
DaVinci GIT kernels since 2.6.24, and mainline Linux since 2.6.30,
match non-BROKEN code paths for 1-bit HW ECC. The BROKEN code paths
do seem to partially match what MontaVista/TI kernels (4.0/2.6.10,
and 5.0/2.6.18) do ... but only for small pages. Large page support
is really broken (and it's unclear just what software it was trying
to match!), and the ECC layout was making three more bytes available
for use by filesystem (or whatever) code.
Since this option itself seems broken, remove it. Add a comment
about the MV/TI compat issue, and the most straightforward way to
address it (should someone really need to solve it).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Minor cleanup for DaVinci NAND code:
- Use I/O addresses from nand_chip; CONFIG_SYS_NAND_BASE won't
be defined when there are multiple chipselect lines in use
(as with common 2 GByte chips).
- Cleanup handling of EMIF control registers
* Only need one pointer pointing to them
* Remove incorrect and unused struct supersetting them
- Use the standard waitfunc; we don't need a custom version
- Partial legacy cleanup:
* Don't initialize every board like it's a DM6446 EVM
* #ifdef a bit more code for BROKEN_ECC
Sanity checked with small page NAND on dm355 and dm6446 EVMs;
and large page on dm355 EVM (packaged as two devices, not one).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
To enable CAN init, CONFIG_CAN has to be defined in the board config file
and at91_can_hw_init() has to be called in the board specific code.
CAN is available on AT91SAM9263 and AT91CAP9 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Defining the next two configs allows to switch the serial port from the
console using the setenv stdin and stdout
1. #define CONFIG_SERIAL_MULTI 1 /* Enable both serial ports */
2. #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DMA support is now enabled via the CONFIG_FSL_DMA define instead of the
previous CONFIG_DDR_ECC
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We want the outbound PCI memory map to end at the 4G boundary so we
can maximize the amount of space available for inbound mappings if
we have large amounts of memory.
This matches the device tree setup in the kernel for the 36-bit physical
configs for the platforms that have one (MPC8641 HPCN & MPC8572 DS).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Unify with 83xx and 85xx and use CPU_TYPE_ENTRY. We are going to use
this to convey the # of cores and DDR width in the near future so its
good to keep in sync.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
This patch adds the NAND SPL framework needed to boot i.MX31 boards
from NAND.
It has been tested on a i.MX31 PDK board with large page NAND. Small
page NANDs should work as well, but this has not been tested.
Note: The i.MX31 NFC uses a non-standard layout for large page NANDs,
whether this is compatible with a particular setup depends on how
the NAND device is programmed by the flash programmer (e.g. JTAG
debugger).
The patch is based on the work by Maxim Artamonov.
Signed-off-by: Maxim Artamonov <scn1874@yandex.ru>
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
this will allow you to store use it for the env and to boot directly U-Boot from
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The PM9261 board is based on the AT91SAM9261-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
move PSRAM init to pm9263.c
this will allow us after to make the nor lowlevel_init generic
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The SPI flash define is named CONFIG_SF_DEFAULT_SPEED, not
CONFIG_SF_DEFAULT_HZ, so fix the typos in the Blackfin boards.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The latest version of U-Boot got a bit fatter in the BSS section which
caused overflows in the RAM region, so increase the monitor size.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SPI flash layer is much stricter about sector usage than the eeprom
layer we used to use, so update the env settings to better match the
sector alignment of the flashes we use.
Signed-off-by: Vivi Li <vivi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
All drivers need to be converted to CONFIG_NET_MULTI.
This patch converts the dm9000 driver.
Signed-off-by: Thomas Smits <ts.smits@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds a egiga driver for the Marvell Kirkwood SoC's.
Contributors:
Yotam Admon <yotam@marvell.com>
Michael Blostein <michaelbl@marvell.com
Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
Acked-by: Stefan Rose <sr@denx.de>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Different flavours of DaVinci SOC's have differences in their EMAC IP
This patch does the following
1) Updates base addresses for DM365
2) Updates MDIO frequencies for DM365 and DM646x
3) Update EMAC wrapper registers for DM365 and DM646x
Patch applies to u-boot-net git. the EMAC driver itself
will be updated shortly to add support for DM365 and DM646x
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Added CONFIG_NET_MULTI to all Davinci boards
Removed all calls to Davinci network driver from board code
Added cpu_eth_init() to cpu/arm926ejs/cpu.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
All the Blackfin linker scripts were duplicated across the board dirs with
no difference save from the semi-often used ENV_IS_EMBEDDED option. So
unify all of them in the lib_blackfin/ dir and for the few boards that
need to embedded the environment directly, add a LDS_BOARD_TEXT define for
them to customize via their board config file. This is much simpler than
forcing them to duplicate the rest of the linker script.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF51xF parts have an internal SST SPI flash, so make sure the driver is
enabled by default so we can access it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin port was using asm/blackfin-config-{pre,post}.h to setup
common Blackfin board defines. The common method now is to use config.h,
so convert blackfin-config-post.h to that. Rename the still Blackfin
specific blackfin-config-pre.h to config-pre.h so the naming conventions
at least line up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Allow boards to easily override the root= and default bootcmd, allow
people to tweak the file used in default bootcmds at runtime via one env
var, and add a stock nandboot command.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Newer Blackfin parts can an on-chip ROM that can boot LDRs over SPI flashes,
so add a new 'spibootldr' command to take advantage of it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add defines similar to those already used for the the 86xx architecture.
This will ease sharing of PCI code between the 85xx and 86xx
architectures.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following changes were made to sync up the DMA code between the 85xx
and 86xx architectures which will make it easier to break out common
8xxx DMA code:
85xx:
- Don't set STRANSINT and SPCIORDER fields in SATR register. These bits
only have an affect when the SBPATMU bit is set.
- Write 0xffffffff instead of 0xfffffff to clear errors in the DMA
status register. We may as well clear all 32 bits of the register...
86xx:
- Add CONFIG_SYS_MPC86xx_DMA_ADDR define to address DMA registers
- Add clearing of errors in the DMA status register when initializing
the controller
- Clear the channel start bit in the DMA mode register after a transfer
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Break out DMA structures for the Freescale MPC85xx and MPC86xx cpus to
reduce a large amount of code duplication
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On MPC8569MDS board, UCC6 and UCC8 can be configured to work at SGMII mode via
UEM on PB board. Since MPC8569 supports up to 4 Gigabit Ethernet ports, we
disable UEC6 and UEC8 by default.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch supports UCC working at RMII mode on PIB board, fixup fdt blob to
support rmii in kernel. It also changes the name of enable_mpc8569mds_qe_mdio to
enalbe_mpc8569mds_qe_uec which is more accurate.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some QE chips like 8569 need more SNUM numbers for supporting 4 UECs in RGMII-
1000 mode.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also define the QE_RISC_ALLOCATION_RISCs to MACROs instead of using enum, and
define MAX_QE_RISC for QE based silicons.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Acked-by: Timur Tabi <Timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds NAND support to the MPC5121ADS board. Please
note that the image size increased since NAND support didn't
fit in the current image size (256k).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The CPCI750 can be built as CPCI host or adapter/target board. This patch
adds support for runtime detection of those variants.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
This patch adds CONFIGs for enabling USB in mpc8536ds and also
adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its
Copyright.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch adds CONFIGs for enabling USB in mpc8315erdb and also
adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its
Copyright.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The following patch adds 85xx-specific USB support and also
revamps Copyright in immap_85xx.h
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The following patch reorganizes/reworks the USB support for mpc83xx
as under:-
* Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to
cpu/mpx83xx/cpu_init.c
* Board specific usb_phy_type is read from the environment
* Adds USB EHCI specific structure in include/usb/ehci-fsl.h
* Copyrights revamped in most of the following files
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The following patch moves 8xxx-specifc USB #defines from
drivers/usb/host/ehci-fsl.h to include/usb.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Move needed definitions (register descriptions etc.) from
include/mpc512x.h into include/asm-ppc/immap_512x.h.
Instead of using a #define'd register offset, use a function that
provides the PATA controller's base address.
All the rest of include/mpc512x.h are register offset definitions
which can be eliminated by proper use of C structures.
There are only a few register offsets remaining that are needed in
cpu/mpc512x/start.S; for these we provide cpu/mpc512x/asm-offsets.h
which is intended as a temporary workaround only. In a later patch
this file will be removed, too, and then auto-generated from the
respective C structs.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
We rename the board so we use a consistent name in U-Boot and in
Linux. Also, we use this opportunity to move the board into the
Freecale vendor directory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
In case of incorrect command invocations U-Boot used to print pretty
useless "usage" messages, for example:
=> nand markbad
Usage:
nand - NAND sub-system
In the result, the user would have to run the "help" command to get
the (available) information about correct command usage. Change this,
so that this information gets always printed.
Note that this changes the user interface of all commands, but
hopefully to the better.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The kernel stores address<->symbol names in it so things can be decoded at
runtime. Do it in U-Boot, and we get nice symbol decoding when crashing.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
By changing the cmd_mtdparts to only use the MTD infrastructure and
not the direct interface to the CFI NOR FLASH driver we now need
to add the MTD infrastructure to all boards using those mtdparts
commands. This patch adds those components:
CONFIG_MTD_DEVICE (for all FLASH types)
plus
CONFIG_FLASH_CFI_MTD (for NOR FLASH)
To all board maintainers: Please test this on your platforms and
report any problems/issues found. Thanks.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ron Madrid <info@sheldoninst.com>
Cc: Georg Schardt <schardt@team-ctech.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Martin Krause <martin.krause@tqs.de>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Ricardo Ribalda <ricardo.ribalda@uam.es>
This patch brings the U-Boot MTD infrastructure in sync with the current
Linux MTD version (2.6.30-rc3). Biggest change is the 64bit device size
support and a resync of the mtdpart.c file which has seen multiple fixes
meanwhile.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kyungmin Park <kmpark@infradead.org>
This patch adds concatenation support to the U-Boot MTD infrastructure.
By enabling CONFIG_MTD_CONCAT this MTD CFI wrapper will concatenate
all found NOR devices into one single MTD device. This can be used by
e.g by UBI to access a partition that spans over multiple NOR chips.
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the function and interface clocks for banks 2,3,5 and 6.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
This patch assigns the u-boot system timer interrupt to
interrupt level 3, priority 6. Without this patch the interrupt
will be a level 0, priority 0, which disables it and cause
u-boot functions that relies on the timer (e.g. sleep command)
to never return.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
With other OMAP3 boards we recently switched to CPU and Board
info API. From parallel merge, this is missing for Zoom2.
Enable it for Zoom2, too.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board.
The default serial is from the USB connector on left side of the debug board.
The USB connector will produce 2 of the 4 UARTS. On your host pick the first
enumeration.
The details of the setting of the serial gpmc setup are not available.
The values were provided by another party.
The serial port set up is the same with Zoom1.
Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow.
The kernel bootargs are
console=ttyS3,115200n8
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
all arm init the IRQ stack the same way
so unify it in lib_arm/interrupts.c and then call arch specific interrupt init
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Also enable display of 'E'mpty sectors in "flinfo" output.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Also reserve more space for U-Boot as it will probably grow soon.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Initial U-Boot support for the DaVinci DM355 EVM. This is a board
from Spectrum Digital. Board docs include schematic and firmware
for its microcontroller:
http://c6000.spectrumdigital.com/evmdm355/revd/
Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:
http://focus.ti.com/docs/prod/folders/print/tms320dm355.html
This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART). In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The current configuration doesn't define default
bootfile; leading to this warning at execution:
OMAP3_EVM # dhcp
...
...
DHCP client bound to address 192.168.1.11
*** Warning: no boot file name; using 'AC18BE16.img'
TFTP from server 0.0.0.0; our IP address is 192.168.1.11;
sending through gateway 192.168.1.1
Filename 'AC18BE16.img'.
Load address: 0x82000000
Loading: *
TFTP error: 'File not found' (1)
Signed-off-by: Sanjeev Premi <premi@ti.com>
Port version 2.6.27 of the linux kernel's omap gpio interface to u-boot.
The orignal source is in linux/arch/arm/plat-omap/gpio.c
See doc/README.omap3 for instructions on use.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This updates the optional (non-default!) NAND support for the
DaVinci DM6446 EVM:
- include MTD partitioning, defaulting to what Linux uses
- use a flash-based BBT, which among other things speeds bootup
This matches code that's now queued for mainline Linux, and might
even merge in an upcoming 2.6.30-rc; and the MTIDS are set up so
that the U-Boot $mtdparts environment variable can be passed as-is
on the kernel command line as a cmdlinepart override.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move the clock-rate dumping code into the cpu/.../davinci area
where it should have been, enabled by CONFIG_DISPLAY_CPUINFO,
updating the format and showing the DSP clock (where relevant).
Switch boards to use the cpuinfo() hook for this stuff.
Remove a few now-obsolete PLL #defines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
actually the timer init use the interrupt_init as init callback
which make the interrupt and timer implementation difficult to follow
so now rename it as int timer_init(void) and use interrupt_init for interrupt
btw also remane the corresponding file to the functionnality implemented
as ixp arch implement two timer - one based on interrupt - so all the timer
related code is moved to timer.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Add some basic declarations for DaVinci DM355/DM350/DM335 support,
keyed on CONFIG_SOC_DM355. (DM35X isn't quite right because the
DM357 is very different; while the DM355 is like a DM355 without
the MPEG/JPEG coprocessor).
These have different peripherals than the DM6446, and some of
the peripherals are at different addresses. Notably for U-Boot,
there's no EMAC, and the NAND controller address is different
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Split out DaVinci DM6446-specific bits from more generic bits:
- Add a CONFIG_SOC_DM644X. All current boards use DM6446 chips;
DM6443 and DM6441 chips differ in available peripherals.
- Move most DM644X-specific bits from psc.c to a new dm644x.c file,
which is conditionally built. It provides device-specific setup.
Plus minor coding style and comment updates with respect to the PSC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move DaVinci PSC support from board/* to cpu/* where it belongs.
The PSC module manages clocks and resets for all DaVinci-family
SoCs, and isn't at all board-specific.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch adds another build target for the AMCC Sequoia PPC440EPx
eval board. This RAM-booting version is targeted for boards without
NOR FLASH (NAND booting) which need a possibility to initially
program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000)
configured to setup the SDRAM, this debugger can load this RAM-
booting image to the target address in SDRAM (in this case 0x1000000)
and start it there. Then U-Boot's standard NAND commands can be
used to program the NAND FLASH (e.g. "nand write ...").
Here the commands to load and start this image from the BDI2000:
440EPX>reset halt
440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin
440EPX>go 0x1000000
Please note that this image automatically scans for an already
initialized SDRAM TLB (detected by EPN=0). This TLB will not be
cleared. This TLB doesn't need to be TLB #0, this RAM-booting
version will detect it and preserve it. So booting via BDI2000
will work and booting with a complete different TLB init via
U-Boot works as well.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on DP405 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit. Some unused featues have been
removed therefore.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on VOM405 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on PMC405 boards.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on CMS700 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit. Some unused featues have been
removed therefore.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop,
and isdram are no longer available so all references to them have been
updated to the new form of "i2c <cmd>".
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.
The functionality of the individual commands is still available via
the 'i2c' command.
This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Add standard CONFIG_SYS_I2C_SPEED define for the mpc7448hpc2 so that
it can use the common 'i2c speed' command. Note that the I2C controller
utilized by the mpc7448hpc2 has a fixed speed and cannot be changed
dynamically.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Many boards/controllers/drivers don't support an I2C slave interface,
however CONFIG_SYS_I2C_SLAVE is used in common code so provide a
default
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Yu Liu <Yu.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Increase the size of malloc to 512KB because MPC8569MDS needs more memory for
malloc to support up to eight Ethernet interfaces.
- Move Environment address out of uboot thus the saved environment variables
will not be erased after u-boot is re-programmed.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove "saveenv" from "update" definition: the environment is outside
the U-Boot image on TQM85xx and therefor not affected by updates.
Also "beautify" code a bit (vertical alignment).
Signed-off-by: Wolfgang Denk <wd@denx.de>
Old TQM85xx boards had 'M' type Spansion Flashes from the S29GLxxxM
series while new boards have 'N' type Flashes from the S29GLxxxN
series, which have bigger sectors: 2 x 128 instead of 2 x 64 KB.
We now change the configuration to the new flash types for all
boards; this also works on old boards - we just waste two flash
sectors for the environment which could be smaller there.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The SYS_CLK_IN of MPC8569MDS is 66.66MHz,
The DDR_CLK_IN is same with SYS_CLK_IN in 8569 processor.
so, change the SYS_CLK_IN from 66MHz to 66.66MHz.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Some boards do not have SROM support for the DM9000 network adapter.
Instead of listing these board names in the driver code, make this
option configurable from the board config file.
It also removes a build warning for the at91sam9261ek board:
'dm9000x.c:545: warning: 'read_srom_word' defined but not used'
And it repaires the trizepsiv board build which was broken around the
same routines
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
In GMII mode (which operates at 3.3V) both SICRH TSEC1/2 output buffer
impedance bits should be clear, i.e., SICRH[TSIOB1] = 0 and SICRH[TSIOB2] = 0.
SICRH[TSIOB1] was erroneously being set high.
U-Boot always operated this PHY interface in GMII mode. It is assumed this
was missed in the clean up by the original board porters, and copied along
to the TQM and sbc boards.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Ira Snyder <iws@ovro.caltech.edu>
Reviewed-by: David Hawkins <dwh@ovro.caltech.edu>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Dave Liu <DaveLiu@freescale.com>
The mmc code defines the response as an array of chars. However, it
access the response bytes both as (i) an array of four uints (with
casts) and (ii) as individual chars. The former case is used more
often, including by the driver when it assigns the response.
The char-wise accesses are broken on little endian systems because they
assume that the bytes in the uints are in big endian byte order.
This patch fixes this by changing the response to be an array of four
uints and replacing the char-wise accesses with equivalent uint-wise
accesses.
Signed-off-by: Rabin Vincent <rabin@rab.in>
A missing set of parenthesis caused the silicon revision to apply only to
the BF533 and not the BF531/BF532 variants.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The pins for async memory where parallel flash lives are not enabled by
default, so make sure we mux them as needed.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch moves the definition for the PPC4xx NAND FLASH controller
(NDFC) CONFIG_NAND_NDFC into include/ppc4xx.h. This is needed for the
upcoming fix for the ECC byte ordering of the NDFC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
All these functions are expected to be static inline-ed.
This patch also fixes the following build warnings on MIPS targets:
include/asm/bitops.h: In function 'ext2_find_next_zero_bit':
include/asm/bitops.h:862: warning: '__fswab32' is static but used in inline function 'ext2_find_next_zero_bit' which is not static
include/asm/bitops.h:885: warning: '__fswab32' is static but used in inline function 'ext2_find_next_zero_bit' which is not static
include/asm/bitops.h:887: warning: '__fswab32' is static but used in inline function 'ext2_find_next_zero_bit' which is not static
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
U-Boot does not currently build for PXA platforms with USB support
enabled:
usb.c:46: error: 'UP2OCR' undeclared (first use in this function)
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Markus Klotzbuecher <mk@denx.de>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add CONFIG_SYS_MONITOR_LEN macro to apollon board config.
CONFIG_SYS_MONITOR_LEN defines the U-Boot image size.
and is used by OneNAND ipl when reading U-Boot image.
Signed-off-by: Rohit Hagargundgi <h.rohit at samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
The pin which was used in preliminary versions of the board for ide
reset is really connected to the rtc clock.
Signed-off-by: Detlev Zundel <dzu@denx.de>
The BF527-EZKIT settings for storing the environment in SPI flash wasn't
using the correct sector settings for the SPI flash part that is actually
on the board.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When dropping jump block support, the assumption was that all bootroms
supported entry point redirection via the EVT1 register. Unfortunately,
this turned out to be incorrect for the oldest Blackfin parts (BF533-0.2
and older and BF561). No one really noticed earlier because these parts
usually are booted by bypassing the bootrom entirely, and older BF533
parts are not supported at all (too many anomalies).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Let CONFIG_SYS_HZ to have value of 1000 effectively fixing all users of
get_timer.
Changes since original version:
* Set PTV=2 (divisor 8) for boards using 12MHz timer clock source to
improve timer resolution.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
The function display_board_info() displays incorrect
silicon revision - based on the return value from
function get_cpu_rev().
This patch fixes the problem.
Signed-off-by: Sanjeev Premi <premi@ti.com>
The board-types defined in struct omap3_sysinfo seem to be
unused. The function display_board_info() is passed
board type as an argument; which is ignored.
This patch removes all uses of board-type, related definitions
and functions.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Use the functions print_cpuinfo() and checkboard() to
display the cpu and board specific information.
These functions reuse content from the existing function
display_board_info() - which has been removed.
Also, updated the existig OMAP3 configurations to
define:
- CONFIG_DISPLAY_CPUINFO
- CONFIG_DISPLAY_BOARDINFO
Signed-off-by: Sanjeev Premi <premi@ti.com>
because legacy NAND support is deprecated converting to current
NAND interface. !This just compile, because I have no more the
hardware to test it.
Signed-off-by: Heiko Schocher <hs@denx.de>
As the common code also handles baudrate switching, which the board
specific vct.c driver did not support, this is one of the rare
occassions where deleting code actually adds a feature :)
Signed-off-by: Detlev Zundel <dzu@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
__attribute__ follows gcc's documented syntax and is generally more
common than __attribute. This change is only asthetic and should not
affect functionality.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Minor cleanup to clock-related defines for DaVinci DM6446 boards:
- CONFIG_SYS_CLK_FREQ is unused; remove it.
- CONFIG_SYS_NS16550_CLK must be the same as CONFIG_SYS_HZ_CLOCK
On DM6446 both of those peripheral clocks actually come from the
same source, the primary oscillator. Having them use the same
symbol avoids bugs in the clone'n'modify development cycle.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The size of U-Boot binary for MPC8360ERDK increased
(> 2 flash sectors now), so 'saveenv' will partially
overwrite U-Boot in flash and will brick the board.
This patch moves environment offset to fourth flash
sector and also fixes CONFIG_SYS_MONITOR_LEN.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Change netdev.h to use CONFIG_ULI526X instead of CONFIG_ULI526. CONFIG_ULI526X
is used everywhere else, so that's the correct macro name. Without this fix,
Ethernet will not work on the Freescale MPC8610 HPCD.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Update the DaVinci DM6446 boards to use the new convention
for CONFIG_SYS_NS16550_REG_SIZE ... the size hasn't changed
from the original 4 bytes, but these chips are little-endian.
(Resolves a regression added recently by the include/ns16550.h
patch to "Unify structure declaration for registers". The code
previously worked just fine because the registers were accessed
as host-endian words, not as bytes.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The timer has been rewrote with a precision at ~0,18%
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Tested-by: Eric BENARD <ebenard@free.fr>
The PM9263 board is based on the AT91SAM9263-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Don't run the memory POST on the NAND-booting version. It will
overwrite part of the U-Boot image which is already loaded from NAND
to SDRAM. We were just lucky that it booted at all with this SDRAM
test enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Don't run the memory POST on the NAND-booting version. It will
overwrite part of the U-Boot image which is already loaded from NAND
to SDRAM. We were just lucky that it booted at all with this SDRAM
test enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
This Patch adds Support for PXA27X UDC.
(Rebased to drivers/usb reorganisation)
Signed-off-by: Vivek Kutal <vivek.kutal@azingo.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
move to linux usb driver organisation
as following
drivers/usb/gadget
drivers/usb/host
drivers/usb/musb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Move machine specific code to smdk6400.
Some board use OneNAND instead of NAND.
Some register MP0_CS_CFG[5:0] are controled by both h/w and s/w.
So it's better to use macro instead of hard-coded value.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
On platforms with multiple NOR chips, currently only the first one
can be selected using the "ubi part" command. This patch fixes this
problem by using different names for the NOR "mtd devices".
It also changes the name of the NOR MTD device from "cfi-mtd" to
"norX" (X indexing the device numer) to better match the mtdparts
defaults.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
introduce serial_exit for this purpose. Use it only when the rm9200
serial driver is active
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507
with
- NOR (cfi driver)
- DataFlash
- USB OHCI
- Net
- I2C (hard)
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Rename the pci header for FSL HW so we can move some prototypes
in there and stop doing explicit externs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some systems have zlib.h installed in /usr/include/. This isn't the
desired file for u-boot code - we want the one in include/zlib.h.
This rename will avoid the conflict.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Instead of special casing the different access patterns, use common
code with light macros sprinkled in to accomodate for the different
layouts of the register structure.
Note that this also changes the types of the registers for the
"positively packed (>1)" cases. As the registers truly are unsigned
chars, this is surely the Right Thing, but it is a semantic change.
Note that for this case depending on the endianness on the bus, we may
see a change of behaviour.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Add support for compiling the host tools in the tools directory using
the MinGW toolchain. This produces executables which can be used on
standard Windows computers without requiring cygwin.
One must specify the MinGW compiler and strip utilities as if they
were the host toolchain in order to build win32 executables, eg:
make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The original code provided an incomplete set of typedefs for WIN32
compiles and replicated the standard typedefs that are already
provided by stdint.h
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Mflash is fusion memory device mainly targeted consumer eletronic and
mobile phone.
Internally, it have nand flash and other hardware logics and supports
some different operation (ATA, IO, XIP) modes.
IO mode is custom mode for the host that doesn't have IDE interface.
(Many mobile targeted SoC doesn't have IDE bus)
This driver support mflash IO mode.
Followings are brief descriptions about IO mode.
1. IO mode based on ATA protocol and uses some custom command. (read
confirm, write confirm)
2. IO mode uses SRAM bus interface.
Signed-off-by: unsik Kim <donari75@gmail.com>
