As the timer 2 is on APB1 bus, the maximum of clock frequency of APB1 timer
clock is half of SYSCLK. Then to calculate the timer prescaler for timer 2
which need to be divided by 2.
Signed-off-by: Bo Shen <voice.shen@gmail.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Check malloc() return values and properly unwind on errors so
memory allocated for fat_itr structures get freed properly.
Also fixes a leak of fsdata.fatbuf in fat_size().
Fixes: 2460098cff ("fs/fat: Reduce stack usage")
Reported-by: Coverity (CID: 167225, 167233, 167234)
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
The 'block' field of fat_itr needs to be properly aligned for DMA and
while it does have '__aligned(ARCH_DMA_MINALIGN)', the fat_itr structure
itself needs to be properly aligned as well.
While at it use malloc_cache_aligned() for the other aligned allocations
in the file as well.
Fixes: 2460098cff ("fs/fat: Reduce stack usage")
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
In the Linux Kernel on ARM64, the Image.COMPRESSION file is not
self-extracting in the way that x86 and ARM images are. So when
CMD_BOOTI is enabled we should also default to enabling CMD_UNZIP and
CONFIG_LZMA in order for the user to be able to decompress many of the
common compressions that will be done to an Image file.
Signed-off-by: Tom Rini <trini@konsulko.com>
On case-insensitive file systems we have collision between
scripts/kconfig/ directory and scripts/Kconfig file. This patch moves
scripts/Kcofnig contents to cmd/Kconfig to fix that.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This driver is currently used by STM32F7 and STM32H7 SoCs.
As CONFIG_CLK and OF_CONTROL flags are set by default for these
2 SoCs, this flag becomes useless in this driver, so remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
stm32f4 doesn't support FIFO and OVERRUN feature.
The enable bit is not at the same location in CR1
register than for STM32F7 and STM32H7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add fifo mode support for rx and tx.
As only STM32H7 supports this feature, add has_fifo flag
to uart configuration to use fifo only when possible.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
STM32F4 serial IP is similar to F7 and H7, but registers
are not located at the same offset and some feature are
only supported by F7 and H7 version.
Registers offset must be added for each version and also
some flags indicated the supported feature.
Update registers name to match with datasheet (sr to isr,
rx_dr to rdr and tx_dr to tdr) and remove unused regs
(cr2, gtpr, rtor, and rqr).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch remove the extra compatibility string "st,stm32h7-usart"
and "st,stm32f7-usart" to avoid confusion, save some time & space.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
macro branch_if_master checks master CPU via (Aff3 & (Aff2:Aff1:Aff0))
it is simple but a little obscure.
fix by checking Affx fields within MPIDR_EL1 directly.
Signed-off-by: zijun_hu <zijun_hu@htc.com>
relocate_code() allocates 32 bytes stack frame but only 16 bytes are
freed before return. it will cause errors to possible previous frames
and doesn't make relocate_code() look like a function.
fix by freeing 32 bytes stack space
Signed-off-by: zijun_hu <zijun_hu@htc.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
the new GD address is calculated via board data BD currently
it require the new GD area locates below BD tightly, so a strict
constraint is imposed on memory layout which maybe make special
platform unpleasant.
fix it by getting new GD address from gd->new_gd directly.
Signed-off-by: zijun_hu <zijun_hu@htc.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Given how we handle the ARM toolchain we can't easily combine these two
jobs, so don't. Give xilinx/ARM a separate build.
Signed-off-by: Tom Rini <trini@konsulko.com>
The recent changes to these files did not completely fix the previous
issues, or introduced different (minor) issues. In cmd/gpt.c we need to
dereference str_disk_guid to be sure that malloc worked. In
cmd/nvedit.c we need to be careful that we can also fit in that leading
space when adding to the string. And in tools/fit_image.c we need to
re-work the error handling slightly in fit_import_data() so that we only
call munmap() once. We have two error paths here, one where we have an
fd to close and one where we do not. Adjust labels to match this.
Reported-by: Coverity (CID: 167366, 167367, 167370)
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is based on Intel Tangier SoC (Intel Merrifield platform)
and may utilize ACPI powerfulness.
Bring minimum support by appending initial DSDT table for it.
Note, the addresses for generated tables are carefully chosen to avoid
any conflicts with existing shadowed BIOS data. The user have somewhat
like ~31 kB available for compiled ACPI tables that ought to be enough.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Intel Tangier SoC is a part of Intel Merrifield platform which doesn't
utilize ACPI by default. Here is an attempt to unleash ACPI flexibility
power on Intel Merrifield based platforms.
The change brings minimum support of the devices that found on
Intel Merrifield based end user device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The setexpr command is useful for scripting, lets enable it for all
x86 based theadorable platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This enables the easier usage of "-custom" kernel versions as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is needed for the PCIe hotplug to work correctly on some boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Move SoCFPGA and K2 boards to their own job
- Expand the microblaze job to cover ARM boards from Xilinx as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
As reported by Coverity, we did not free dirnode in the case of failure.
Do so now.
Reported-by: Coverity (CID: 131221)
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Coverity has found some problems with the return paths in parts of this
code. We have a case where we were going to the wrong part of the
unwind (open() failed so we cannot close the fd), a case where we were
only free()ing our buf on the error path and finally a case where we did
not munmap in the failure path.
Reported-by: Coverity (CID: 138492, 138495, 143064)
Signed-off-by: Tom Rini <trini@konsulko.com>
For the initrd portion of handling our bootm arguments we do not have a
sufficiently long enough buffer for some improbable 64bit cases. Expand
this buffer to allow for a 64bit address and almost 256MB initrd to be
used. Make use of strncpy/strncat when constructing the values here
since we know what the worst case valid values are, length wise.
Similarly for bootargs themselves, we need to make use of strlen/sizeof
and strncpy/strncat to ensure that we don't overflow bootargs itself.
Cc: Simon Glass <sjg@chromium.org>
Cc: Alexander Graf <agraf@suse.de>
Reported-by: Coverity (CID: 131256)
Signed-off-by: Tom Rini <trini@konsulko.com>
When we have multiple messages provided, we need to be sure that we do
not exceed the length of our 'message' buffer. In the for loop, make
sure that pos is not larger than message. Only copy in at most however
much of the message buffer remains. Finally, if we have not reached the
end of the message buffer, put in a space and NULL, and if we have,
ensure the buffer is now NULL termined.
Reported-by: Coverity (CID: 165116)
Signed-off-by: Tom Rini <trini@konsulko.com>
Coverity scan has identified potential buffer overruns in these tests.
Correct this by zeroing our buffer and using strncpy not strcpy.
Reported-by: Coverity (CID: 155462, 155463)
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
With the overlay tests now being built in sandbox Coverity has found a
number of issues in the tests. In short, if malloc ever failed we would
leak the previous mallocs, so we need to do the usual goto pattern to
free each in turn. Finally, we always looked at the free()d location to
see how many tests had failed for the return code.
Reported-by: Coverity (CID: 167224, 167227, 167230, 167236)
Signed-off-by: Tom Rini <trini@konsulko.com>
Create a common exit for most of the error handling code in
do_rename_gpt_parts. Delete the list elements in disk_partitions
before calling INIT_LIST_HEAD from get_gpt_info() a second time.
The SIZEOF_MISMATCH error is not addressed, since that problem was
already fixed by "GPT: incomplete initialization in
allocate_disk_part".
Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
Reported-by: Coverity (CID: 167222, 167235, 167237)
Reviewed-by: Tom Rini <trini@konsulko.com>
The previous commit fixed a problem in FAT code where going back to the
root directory using '..' wouldn't work correctly on FAT12 or FAT16.
Add a test to exercise this case (which was once fixed in commit
18a10d46f2 "fat: handle paths that include ../" but reintroduced due to
the directory iterator refactoring).
This test only very barely catches the problem - without the fix the
size command still gives valid output but the additional spurious
"Invalid FAT entry" error message makes it not get caught in the
'egrep -A3 ' output. I tried to make a proper test that grows the root
directory to two clusters lots of with dummy files but that causes the
write tests to crash the sandbox totally...
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
If we end up back in the root directory via a '..' directory entry, set
itr->is_root accordingly. Failing to do that gives spews like
"Invalid FAT entry" and being unable to access directory entries located
past the first cluster of the root directory.
Fixes: 8eafae209c ("fat/fs: convert to directory iterators")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Currently we can only test FAT32 which is the default FAT version that
mkfs.vfat creates by default. Instead make it explicitly create either a
FAT16 or a FAT32 volume. This allows us to exercise more code, for
instance the root directory handling is done differently in FAT32 than
the older FATs.
Adding FAT12 support is a much bigger job since the test creates a 2.5GB
file and the FAT12 maximum partition size is way smaller than that.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
The current code doesn't compute the group descriptor checksum correctly
for the filesystems that e2fsprogs 1.43.4 creates (they have
'Group descriptor size: 64' as reported by tune2fs). Extend the checksum
calculation to be done as ext4_group_desc_csum() does in Linux.
This fixes these errors in dmesg from running fs-test.sh and makes it
succeed again:
[1671902.620699] EXT4-fs (loop1): ext4_check_descriptors: Checksum for group 0 failed (35782!=10965)
[1671902.620706] EXT4-fs (loop1): group descriptors corrupted!
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The regulator bindings state that regulator prefixes are allowd to be
in upper or lower case. However pmic_bind_children from pmic_uclass uses
strncmp to compare DT node name against prefix. This comparison is case
sensitive hence the regulator driver prefix case matters.
Signed-off-by: Felix Brack <fb@ltec.ch>
When eMMC was formattaed for Linux partition table, "userdata" partition
is missing. In this case, part_get_info_by_name() iterates over all
registered drivers (which are PART_TYPE_EFI, PART_TYPE_DOS and
PART_TYPE_ISO). And when it comes to PART_TYPE_ISO (which has empty
partition table), we can see next warning in U-Boot output:
** First descriptor is NOT a primary desc on 1:1 **
This patch switches to part_get_info_by_name_type() API in order to
check only EFI partitions for "userdata" partitions. This eliminates
mentioned warning.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is already existing function part_get_info_by_name().
But sometimes user is particularly interested in looking for only
specific partition type. This patch implements such an API that
provides partition searching by name for specified partition type.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using regular $partitions variable (for Linux boot), we can see
some unwanted messages:
> ERROR: cannot find partition: 'userdata'
> at arch/arm/mach-omap2/utils.c:96/omap_mmc_get_part_size()
> Warning: fastboot.userdata_size: unable to calc
Let's remove those, as missing 'userdata' partition is correct behavior
for Linux partition, and we don't want to see some Android-related
messages in this case.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
This board builds an U-Boot binary that is bootable with QEMU's 'virt'
machine on ARM. The minimal QEMU command line is:
qemu-system-arm -machine virt,highmem=off -bios u-boot.bin
(Note that the 'highmem=off' parameter to the 'virt' machine is required for
PCI to work in U-Boot.) This command line enables the following:
- u-boot.bin loaded and executing in the emulated flash at address 0x0
- A generated device tree blob placed at the start of RAM
- A freely configurable amount of RAM, described by the DTB
- A PL011 serial port, discoverable via the DTB
- An ARMv7 architected timer
- PSCI for rebooting the system
- A generic ECAM-based PCI host controller, discoverable via the DTB
Additionally, QEMU allows plugging a bunch of useful peripherals to the PCI bus.
The following ones are supported by both U-Boot and Linux:
- To add a Serial ATA disk via an Intel ICH9 AHCI controller, pass e.g.:
-drive if=none,file=disk.img,id=mydisk -device ich9-ahci,id=ahci -device ide-drive,drive=mydisk,bus=ahci.0
- To add an Intel E1000 network adapter, pass e.g.:
-net nic,model=e1000 -net user
- To add an EHCI-compliant USB host controller, pass e.g.:
-device usb-ehci,id=ehci
- To add a NVMe disk, pass e.g.:
-drive if=none,file=disk.img,id=mydisk -device nvme,drive=mydisk,serial=foo
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
QEMU emulates such a device with '-machine virt,highmem=off' on ARM.
The 'highmem=off' part is required for things to work as the PCI code
in U-Boot doesn't seem to support 64-bit BARs.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the new helpers to avoid boilerplate in the driver.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the new helper function to avoid boilerplate in the driver.
Note that this changes __raw_writel et al. to writel. AFAICT this is
no problem because:
- The Linux driver for the same hardware uses the non-__raw variants as
well (via pci_generic_config_write()).
- This driver seems to be used only on MIPS so far, where the __raw and
non-__raw accessors are the same.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This sort of pattern for implementing memory-mapped PCI config space
accesses appears in U-Boot twice already, and a third user is coming up.
So add helper functions to avoid code duplication, similar to how Linux
has pci_generic_config_write and pci_generic_config_read.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>