This change follows the change by Wolfgang Grandegger (commit 6c869637fe),
which allows to remove useless NAND_MAX_CHIPS definitions in board config
files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM
which is likely to contain already loaded data.
The patch saves the oob data and the ecc on the stack replacing
the fixed address in RAM.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Ilya Yanok <yanok@emcraft.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Simon Schwarz <simonschwarzcor@googlemail.com>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
* implementation based on ti beagleboard/omap3evm
* timing data and i2c workaround for revision 0 boards taken from x-loader
* run-tested with overo revision 0 and 1 / boot from NAND and SDcard
* run-tested with x-loader
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Signed-off-by: Tom Rini <trini@ti.com>
At old overo boards TWL4030 RTC irq is connected to gpio112. Unfortunately
this pin is also used for revision detection. Therefore we need to send
shut-up to TWL4030 to avoid reading wrong revision. In SPL this must
be done before SDRAM is set up because the type of SDRAM is revision dependent.
By this patch it is ensured that all variables used by omap24xx_i2c.c are
located in SRAM.
Signed-off-by: Andreas Müller <schnitzeltony@gmx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This patch add supports for mmc/sd driver on AM335X platform.
PLL and pinmux configurations for mmc/sd are configured in this
patch.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch is added to correct some of the AM335X config
parameters which were incorrect along with some cleanup
like removing unused code.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch is added to update incorrect ddr and timer
register offset.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch is added to replace CONFIG_AM335X symbol
with CONFIG_AM333XX for AM33XX platforms.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Thomas Weber <weber@corscience.de>
Switch to the new EEPROM module and fix the problem of MAC address
being read from the wrong offset due to lack of distinction between
EEPROM layouts.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Read revision from EEPROM and pass it to Linux.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Current get_board_rev() function returns a hard coded value which is
obviously incorrect for the majority of boards.
Allow boards to provide a correct implementation by making this function
weak.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Add board specific EEPROM handling module,
read the serial number from the EEPROM and pass it to Linux.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Move #ifdef CONFIG_SMC911X out of board_eth_init() function,
simplify the board_mmc_init() function, and enclose handle_mac_address()
in the CONFIG_SMC911X.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Fix boot issue on ES2.0 Panda by tuning some
IO settings. The CONTROL_EFUSE_2 register has
to be over-ridden in software for 4430 boards.
Commit 23e9f0723e
wrongly did this for CONTROL_EFUSE_1. Reverting
this and doing it for CONTROL_EFUSE_2.
Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Raúl Porcel <armin76@gentoo.org>
This patch adds basic support for OMAP35x/DM37x SOM LV/Torpedo
reference boards. It assumes U-boot is loaded to SDRAM with the
help of another small bootloader (x-load) running from SRAM.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Now the values in the defines agree with those in the manuals.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
This patch removes the defines CONFIG_SYS_ICACHE_OFF,
CONFIG_SYS_DCACHE_OFF, and CONFIG_SYS_L2CACHE_OFF from the board
configuration. These defines are useless since cache is
anyway disabled for the entire architecture since commit
cba4b1809f.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Tom Rini <trini@ti.com>
In commit 06194b6b65 a separate header
file was introduced for the AM1808 EVM, include/configs/da850_am18xxevm.h.
Before this commit, the da850evm.h configuration file was used for both
the AM1808 and the OMAP-L138 EVMs. The only substantial difference
between the da850evm and the da850_am18xxevm configuration is a single
bit in the hardware revision that is passed to the Linux kernel.
This patch removes include/configs/da850_am18xxevm.h. Instead the
include/configs/da850evm.h configuration is used for AM18xx EVMs and
CONFIG_DA850_AM18X_EVM is defined in boards.cfg.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Tom Rini <trini@ti.com>
Add the initial support for Freescale i.MX6Q Sabre Lite board
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
CC: Eric Nelson <eric.nelson@boundarydevices.com>
There are 2 locations in the power init code for the mx28 where IRQs are not being cleared because incorrect methods to clear those bits were being used. This was causing my board to get stuck waiting for POWER_CTRL_VDD5V_DROOP_IRQ to clear. Using the correct method to clear the IRQs fixes it.
Signed-off-by: Zach Sadecki <zach@itwatchdogs.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Remove 'all' target from Makefile, as this is unused code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Remove 'all' target from Makefile, as this is unused code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
For the i.mx6q, the burned-in MAC address will be the following odering,
fuse: 0x620[7:0] MAC_ADDR[7:0] ---> mac[5]
fuse: 0x620[15:8] MAC_ADDR[15:8] ---> mac[4]
fuse: 0x620[23:16] MAC_ADDR[23:16] ---> mac[3]
fuse: 0x620[31:24] MAC_ADDR[31:24] ---> mac[2]
fuse: 0x630[7:0] MAC_ADDR[39:32] ---> mac[1]
fuse: 0x630[15:8] MAC_ADDR[47:40] ---> mac[0]
This patch also fix the error caculation for the fuse bank[0] address
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Add initial support for Freescale MX28EVK board.
Tested boot via SD card and by loading a kernel via TFTP through
the FEC interface.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Let dram_init function be a common function, so that other mx28 boards
can reuse it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Let imx_get_mac_from_fuse function be a common function, so that other
mx28 boards can reuse it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter.
This feature is important on mx28 SoC for example that has two FEC ports.
Cc: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Bits 0 and 1 of CCM_CCGR7 are the usboh3 clock enable bits. Enabling this
clock is necessary for the USB download.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
CC: Jason Hui <jason.hui@linaro.org>
Acked-by: Jason Hui <jason.hui@linaro.org>
Config options for OMAP are not used with i.MX28 so remove dead code.
Signed-off-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This enable the network function on the i.mx6q armadillo2
board(arm2), thus we can use tftp to load image from network.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
