Commit Graph

3026 Commits

Author SHA1 Message Date
Tom Rini
6c7010b779 Merge git://git.denx.de/u-boot-fsl-qoriq 2017-12-07 17:56:51 -05:00
Simon Glass
e189a0bda8 log: sandbox: Enable logging
Enable all logging features on sandbox so that the tests can be run.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-12-07 15:17:00 -05:00
Simon Glass
e341434a7f sandbox: Adjust pre-console address to avoid conflict
We cannot use sandbox memory at 0 since other things use memory at that
address. Move it up out of the way.

Note that the pre-console buffer is currently disabled with sandbox, but
this change will avoid confusion if it is manually enabled.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-12-07 15:17:00 -05:00
Udit Agarwal
003c99de10 armv8: LS2080A_SECURE_BOOT: Enable CONFIG_FSL_LS_PPA.
Adds config CONFIG_FSL_LS_PPA and CONFIG_FSL_CAAM in
LS2080AQDS and LS2080ARDB secure boot defconfig.

Removes CONFIG_FIT, as with CONFIG_FSL_LS_PPA enabled,
CONFIG_FIT is selected.

Removes CONFIG_SPL_RSA as in NOR boot SPL boot is not done.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-06 14:55:17 -08:00
Udit Agarwal
2d2219e6b9 armv8: LS1088A_QSPI: Add secure boot defconfigs for QSPI boot.
Add the secure boot defconfigs for QSPI boot on LS1088ARDB
and LS1088AQDS platforms.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-06 14:55:17 -08:00
Ashish Kumar
ba34890420 armv8: ls1088a: Unset USE_BOOTCOMMAND in defconfig
Unset USE_BOOTCOMMAND for all ls1088 defconfig files to fix
redefinition error. USE_BOOTCOMMAND was introduced in commit
b6251db8c3 ("Kconfig: Introduce USE_BOOTCOMMAND and migrate
BOOTCOMMAND").

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-12-06 14:55:17 -08:00
Derald D. Woods
8a3556edba omap3: evm: Explicitly use DISTRO_DEFAULTS features at startup
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot
[fallback 1] Check MMC 0:1 zImage and run mmcbootz
[fallback 2] Check MMC 0:1 uImage and run mmcboot
[fallback 3] Check NAND partitions and run nandboot

If 'extlinux.conf' is not found on MMC 0, the previous boot behavior is
followed.

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2017-12-04 10:23:53 -05:00
Neil Armstrong
c7be3e5a79 ARM: arch-meson: build memory banks using reported memory from registers
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.

But mainline U-Boot and Linux has the old address and size fixed.

These SoCs have a register interface to get the two firmware reserved
memory start and sizes.

This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.

Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].

[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html

Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()

Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception

Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-12-04 10:17:29 -05:00
Neil Armstrong
5ff2ee44ee arm: Add Khadas VIM support based on Meson GXL family
This adds platform code for the Khadas VIM board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.

This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.

The meson-gxl-s905x-khadas-vim.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-12-04 09:59:03 -05:00
Neil Armstrong
96e7b5a174 arm: Add LibreTech CC support based on Meson GXL family
This adds platform code for the Libre Computer CC "Le Potato" board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.

This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.

The meson-gxl-s905x-libretech-cc.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-12-04 09:59:03 -05:00
Dmitry Korunov
8993056fb3 add support for Raspberry Pi Zero W
Signed-off-by: Dmitry Korunov <dessel.k@gmail.com>
2017-12-04 09:59:02 -05:00
Kever Yang
ed7e64e5e8 rockchip: rk3128: add defconfig for evb-rk3128
Enable board config for evb-rk3128.
Serial output and eMMC works in this version.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-11-30 22:55:27 +01:00
Tom Rini
9804d88630 Merge branch 'rmobile-mx' of git://git.denx.de/u-boot-sh 2017-11-30 10:39:04 -05:00
Tom Rini
6ea51d2860 Merge git://git.denx.de/u-boot-x86 2017-11-30 10:37:43 -05:00
Marek Vasut
ab61e17571 ARM: rmobile: Rework the ULCB CPLD driver
Rework the ULCB CPLD driver and make it into a sysreset driver,
since that is what the ULCB CPLD driver is mostly for.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 08:54:18 +01:00
Anatolij Gustschin
a2c0eed4e0 x86: conga-qeval20-qa3-e3845: Adjust VGA rom address
Adjust VGA rom address to 0xfffb0000 so that u-boot.rom image
can be built again.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
2017-11-30 13:50:17 +08:00
Ben Whitten
b2e01ff543 board: laird: add WB50N CPU module
This board is based on the Atmel sama5d3 eval boards.
Supporting the following features:
 - Boot from NAND Flash
 - Ethernet
 - FIT
 - SPL

Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
2017-11-29 22:36:59 -05:00
Ben Whitten
5aaef60077 board: laird: add WB45N CPU module
This board is based on the Atmel 9x5 eval board.
Supporting the following features:
 - Boot from NAND Flash
 - Ethernet
 - FIT
 - SPL

Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
2017-11-29 22:36:59 -05:00
Ludovic Desroches
aaa4ba930c board: atmel: add sama5d2_ptc_ek board
Add the SAMA5D2 PTC EK board and remove the SAMA5D2 PTC ENGI board
which was a prototype.

Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-11-29 22:30:50 -05:00
Patrice Chotard
fe8d4780ff configs: stm32f746-disco: enable MISC/DM_RESET/STM32_RESET and STM32_RCC
This allows to add rcc MFD support to stm32f746-disco board
This rcc MFD driver manages clock and reset for STM32 SoCs family

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
2017-11-29 22:30:50 -05:00
Rick Chen
c39b79df43 nds32: board: Support ftsdc010 DM.
AG101P/AE3XX enable ftsdc010 dm flow.

Signed-off-by: Rick Chen <rick@andestech.com>
2017-11-30 10:04:25 +08:00
Rick Chen
41bbb8b333 spi: nds_ae3xx: Rename nds_ae3xx_spi as atcspi200_spi
atcspi200 is Andestech spi ip which is embedded in
AE3XX and AE250 platforms. So rename as atcspi200
will be more reasonable to be used in different
platforms.

Signed-off-by: Rick Chen <rick@andestech.com>
2017-11-30 09:44:09 +08:00
Rick Chen
fa3e354b2b ae3xx: timer: Rename AE3XX to ATCPIT100
ATCPIT100 is Andestech timer IP which is embeded
in AE3XX and AE250 boards. So rename AE3XX to
ATCPIT100 will be more make sence.

Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-30 09:38:54 +08:00
Marek Vasut
02e80f0c11 ARM: rmobile: Migrate boards to RCar IIC drivers
Stop using the old ad-hoc SH I2C driver and use the new RCar IIC
driver instead. The SH I2C driver should be deprecated and removed
eventually.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:21 +01:00
Marek Vasut
d7f0b85269 ARM: rmobile: Use PRR driver on all Gen3 boards
Mark the PRR as u-boot,dm-pre-reloc in all Gen3 board DTs as it is
needed very early and turn on the CONFIG_SYSCON to allow the PRR
driver to bind as a syscon uclass.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:21 +01:00
Marek Vasut
796411b08a ARM: rmobile: Enable xHCI on RCar Gen3 boards
Enable the XHCI support on all boards.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Marek Vasut
8e8ebd3269 ARM: rmobile: Remove CONFIG_CMD_SDRAM from Salvator-X
This command is useless on Salvator-X as it is reading DRAM info from
SPD. We have no SPD on Salvator-X.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Marek Vasut
fade9f2f16 ARM: rmobile: Enable Micrel KSZ90x1 PHY driver on ULCB
Enable the Micrel KSZ90x1 driver on ULCB, since the board is populated
with KSZ9031 and without this driver, the PHY cannot be operated.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2017-11-30 02:34:20 +01:00
Tom Rini
b06c46de63 Xilinx changes for v2018.1
Zynq:
 - Add support for Syzygy and cc108 boards
 - Add support for mini u-boot configurations (cse)
 - dts updates
 - config/defconfig updates in connection to Kconfig changes
 - Fix psu_init handling
 
 ZynqMP:
 - SPL fixes
 - Remove slcr.c
 - Fixing r5 startup sequence
 - Add support for external pmufw
 - Add support for new ZynqMP chips
 - dts updates
 - Add support for zcu102 rev1.0 board
 
 Drivers:
 - nand: Support external timing setting and board init
 - ahci: Fix wording
 - axi_emac: Wait for bit, non processor mode, readl/write conversion
 - zynq_gem: Fix SGMII/PCS support
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iEYEABECAAYFAloeqWoACgkQykllyylKDCHO1wCggsSgQqOPdCo207FqI3yj2p0E
 MYkAoI1wKvQcjGJJY19YEC1r70Op8RNo
 =BqNN
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2018.01' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.1

Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling

ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board

Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
2017-11-29 08:26:07 -05:00
Michal Simek
2665fb0336 arm: zynq: Enable debug uart on zc706
Enable debug uart by default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-29 08:02:38 +01:00
Masahiro Yamada
53c149c3a5 ARM: uniphier: set CONFIG_LOGLEVEL to 6
Print out KERN_NOTICE or higher level log messages.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:59 +09:00
Masahiro Yamada
ab5502bf56 ARM: openrd: set CONFIG_LOGLEVEL to 2
These boards are on the boundary of "u-boot-nodtb.bin exceeds file
size limit" error.

Reduce the log-level to save memory footprint.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:57 +09:00
Michal Simek
70c42b4ca4 arm64: zynqmp: Add revision to identification string
It is good to see revision in boot log.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:23 +01:00
Michal Simek
ae9775f822 arm64: zynqmp: Add support for zcu102 1.0 rev
1.0 rev is the latest rev. Describe information in eeprom.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:11 +01:00
Michal Simek
96894d3a9e arm64: zynqmp: Enable debug uart for zc1751 dc5
Showing uart earlier.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:09:01 +01:00
Michal Simek
dea4d2f01d arm: zynq: Add mini u-boot configuration for zynq
Add configuration files/dtses for mini u-boot configurations which runs
out of OCM.

ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE
0xfffc0000
+#define CONFIG_SYS_SDRAM_SIZE  0x40000
was hardcoded.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:47 +01:00
Michal Simek
809704eb4f arm: zynq: Move ZYNQ_SERIAL to Kconfig
Move cadence/zynq serial driver via Kconfig

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:45 +01:00
Michal Simek
7fad6125e4 arm: zynq: Enable FPGA/FPGA_XILINX via Kconfig
Enabling fpga via Kconfig.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 16:08:45 +01:00
Michal Simek
bc133e80ae arm: zynq: Add board support for cc108
cc108 board is wiring uart via PL which is good platform for SPL fpga
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-28 16:08:40 +01:00
Michal Simek
7111d6ed86 arm: zynq: Enable qspi for zc770_xm013
Enable qspi driver and flashes for this board.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Michal Simek
b2ff7fb673 arm: zynq: Enable MACRONIX flash for zc702/zc706/zc770 xm010
Enable MACRONIX flash for boards with QSPI enabled.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Michal Simek
4c82ab9d29 arm: zynq: Enable debug console on zc770 xm010 by default
Enable debug console.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Michal Simek
20dff6f153 arm: zynq: Enable bootz command for Xilinx platforms
bootz command is valid way how to boot Linux kernel. Enable it by
default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:08 +01:00
Tom McLeod
413ab5b0e1 arm: zynq: Add support for SYZYGY Hub board
Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board
contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports
booting from SD.

Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Michal Simek <monstr@monstr.eu>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-28 15:53:07 +01:00
Tom Rini
7fef459096 spl: TI: Do not default to SPL_FIT_IMAGE_TINY being enabled
This option prevents booting on am335x_evm at least along with most
likely other platforms.

Fixes: 337bbb6297 ("spl: fit: add SPL_FIT_IMAGE_TINY config to reduce code-size")
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 23:05:11 -05:00
Tom Rini
6e6cf015e7 Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-27 07:22:11 -05:00
Jagan Teki
5451ca4da9 configs: icore-rqs: Enable falcon mode
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
52aaddd6f4 i.MX6: engicam: Add imx6q/imx6ul boards for existing boards
Add new board names for existing board support
imx6q - icore and icore_rqs boards
imx6ul - geam6ul and isiot boards

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
152038ea18 i.MX6UL: icore: Add SPL_OF_CONTROL support
Add OF_CONTROL support for SPL code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00
Jagan Teki
1f6e9bd2a7 i.MX6Q: icore: Add SPL_OF_CONTROL support
Add OF_CONTROL support for SPL code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-11-27 10:36:40 +01:00