board: atmel: add sama5d2_ptc_ek board

Add the SAMA5D2 PTC EK board and remove the SAMA5D2 PTC ENGI board
which was a prototype.

Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
This commit is contained in:
Ludovic Desroches 2017-11-17 14:57:12 +08:00 committed by Tom Rini
parent 48e4851f49
commit aaa4ba930c
17 changed files with 554 additions and 488 deletions

View File

@ -427,6 +427,9 @@ dtb-$(CONFIG_TARGET_OMAP3_LOGIC) += \
logicpd-torpedo-37xx-devkit.dtb \
logicpd-som-lv-37xx-devkit.dtb
dtb-$(CONFIG_TARGET_SAMA5D2_PTC_EK) += \
at91-sama5d2_ptc_ek.dtb
dtb-$(CONFIG_TARGET_SAMA5D2_XPLAINED) += \
at91-sama5d2_xplained.dtb

View File

@ -0,0 +1,215 @@
/*
* at91-sama5d2_ptc_ek.dts - Device Tree file for SAMA5D2 PTC EK board
*
* Copyright (C) 2017 Microchip Technology Inc,
* Ludovic Desroches <ludovic.desroches@microchip.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "sama5d2.dtsi"
#include "sama5d2-pinfunc.h"
/ {
model = "Atmel SAMA5D2 PTC EK";
compatible = "atmel,sama5d2-ptc_ek", "atmel,sama5d2", "atmel,sama5";
chosen {
u-boot,dm-pre-reloc;
stdout-path = &uart0;
};
ahb {
usb0: gadget@00300000 {
atmel,vbus-gpio = <&pioA PIN_PA27 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usba_vbus>;
status = "okay";
};
usb1: ohci@00400000 {
num-ports = <3>;
atmel,vbus-gpio = <0
&pioA PIN_PB12 GPIO_ACTIVE_HIGH
0
>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb_default>;
status = "okay";
};
usb2: ehci@00500000 {
status = "okay";
};
sdmmc0: sdio-host@a0000000 {
bus-width = <8>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc0_cmd_dat_default &pinctrl_sdmmc0_ck_cd_default>;
status = "okay";
u-boot,dm-pre-reloc;
};
sdmmc1: sdio-host@b0000000 {
bus-width = <4>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdmmc1_cmd_dat_default &pinctrl_sdmmc1_ck_cd_default>;
status = "disabled"; /* conflicts with nand and qspi0*/
u-boot,dm-pre-reloc;
};
apb {
macb0: ethernet@f8008000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_macb0_rmii &pinctrl_macb0_phy_irq>;
phy-mode = "rmii";
status = "okay";
ethernet-phy@1 {
reg = <0x1>;
};
};
uart0: serial@f801c000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0_default>;
status = "okay";
u-boot,dm-pre-reloc;
};
i2c1: i2c@fc028000 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1_default>;
status = "okay";
i2c_eeprom: i2c_eeprom@50 {
compatible = "atmel,24mac402";
reg = <0x50>;
};
};
pioA: gpio@fc038000 {
pinctrl {
pinctrl_i2c1_default: i2c1_default {
pinmux = <PIN_PC6__TWD1>,
<PIN_PC7__TWCK1>;
bias-disable;
};
pinctrl_macb0_phy_irq: macb0_phy_irq {
pinmux = <PIN_PB24__GPIO>;
bias-disable;
};
pinctrl_macb0_rmii: macb0_rmii {
pinmux = <PIN_PB14__GTXCK>,
<PIN_PB15__GTXEN>,
<PIN_PB16__GRXDV>,
<PIN_PB17__GRXER>,
<PIN_PB18__GRX0>,
<PIN_PB19__GRX1>,
<PIN_PB20__GTX0>,
<PIN_PB21__GTX1>,
<PIN_PB22__GMDC>,
<PIN_PB23__GMDIO>;
bias-disable;
};
pinctrl_sdmmc0_cmd_dat_default: sdmmc0_cmd_dat_default {
pinmux = <PIN_PA1__SDMMC0_CMD>,
<PIN_PA2__SDMMC0_DAT0>,
<PIN_PA3__SDMMC0_DAT1>,
<PIN_PA4__SDMMC0_DAT2>,
<PIN_PA5__SDMMC0_DAT3>,
<PIN_PA6__SDMMC0_DAT4>,
<PIN_PA7__SDMMC0_DAT5>,
<PIN_PA8__SDMMC0_DAT6>,
<PIN_PA9__SDMMC0_DAT7>;
bias-pull-up;
u-boot,dm-pre-reloc;
};
pinctrl_sdmmc0_ck_cd_default: sdmmc0_ck_cd_default {
pinmux = <PIN_PA0__SDMMC0_CK>,
<PIN_PA10__SDMMC0_RSTN>,
<PIN_PA11__SDMMC0_VDDSEL>,
<PIN_PA13__SDMMC0_CD>;
bias-disable;
u-boot,dm-pre-reloc;
};
pinctrl_sdmmc1_cmd_dat_default: sdmmc1_cmd_dat_default {
pinmux = <PIN_PA28__SDMMC1_CMD>,
<PIN_PA18__SDMMC1_DAT0>,
<PIN_PA19__SDMMC1_DAT1>,
<PIN_PA20__SDMMC1_DAT2>,
<PIN_PA21__SDMMC1_DAT3>;
bias-pull-up;
u-boot,dm-pre-reloc;
};
pinctrl_sdmmc1_ck_cd_default: sdmmc1_ck_cd_default {
pinmux = <PIN_PA22__SDMMC1_CK>,
<PIN_PA30__SDMMC1_CD>;
bias-disable;
u-boot,dm-pre-reloc;
};
pinctrl_uart0_default: uart0_default {
pinmux = <PIN_PB26__URXD0>,
<PIN_PB27__UTXD0>;
bias-disable;
u-boot,dm-pre-reloc;
};
pinctrl_usb_default: usb_default {
pinmux = <PIN_PB12__GPIO>;
bias-disable;
};
pinctrl_usba_vbus: usba_vbus {
pinmux = <PIN_PB11__GPIO>;
bias-disable;
};
};
};
};
};
};

View File

@ -302,6 +302,7 @@
#clock-cells = <0>;
reg = <24>;
atmel,clk-output-range = <0 83000000>;
u-boot,dm-pre-reloc;
};
uart1_clk: uart1_clk@25 {
@ -315,6 +316,7 @@
#clock-cells = <0>;
reg = <26>;
atmel,clk-output-range = <0 83000000>;
u-boot,dm-pre-reloc;
};
uart3_clk: uart3_clk@27 {
@ -635,6 +637,14 @@
status = "disabled";
};
uart0: serial@f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x100>;
clocks = <&uart0_clk>;
clock-names = "usart";
status = "disabled";
};
uart1: serial@f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x100>;
@ -643,6 +653,14 @@
status = "disabled";
};
uart2: serial@f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x100>;
clocks = <&uart2_clk>;
clock-names = "usart";
status = "disabled";
};
i2c0: i2c@f8028000 {
compatible = "atmel,sama5d2-i2c";
reg = <0xf8028000 0x100>;

View File

@ -143,10 +143,9 @@ config TARGET_AT91SAM9X5EK
select BOARD_EARLY_INIT_F
select BOARD_LATE_INIT
config TARGET_SAMA5D2_PTC
bool "SAMA5D2 PTC board"
config TARGET_SAMA5D2_PTC_EK
bool "SAMA5D2 PTC EK board"
select SAMA5D2
select SUPPORT_SPL
select BOARD_EARLY_INIT_F
config TARGET_SAMA5D2_XPLAINED
@ -251,7 +250,7 @@ source "board/atmel/at91sam9m10g45ek/Kconfig"
source "board/atmel/at91sam9n12ek/Kconfig"
source "board/atmel/at91sam9rlek/Kconfig"
source "board/atmel/at91sam9x5ek/Kconfig"
source "board/atmel/sama5d2_ptc/Kconfig"
source "board/atmel/sama5d2_ptc_ek/Kconfig"
source "board/atmel/sama5d2_xplained/Kconfig"
source "board/atmel/sama5d27_som1_ek/Kconfig"
source "board/atmel/sama5d3_xplained/Kconfig"

View File

@ -1,7 +0,0 @@
SAMA5D2 PTC Engineering BOARD
M: Wenyou Yang <wenyou.yang@atmel.com>
S: Maintained
F: board/atmel/sama5d2_ptc/
F: include/configs/sama5d2_ptc.h
F: configs/sama5d2_ptc_spiflash_defconfig
F: configs/sama5d2_ptc_nandflash_defconfig

View File

@ -1,8 +0,0 @@
#
# Copyright (C) 2016 Atmel
# Wenyou Yang <wenyou.yang@atmel.com>
#
# SPDX-License-Identifier: GPL-2.0+
#
obj-y += sama5d2_ptc.o

View File

@ -1,285 +0,0 @@
/*
* Copyright (C) 2016 Atmel
* Wenyou.Yang <wenyou.yang@atmel.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <atmel_hlcdc.h>
#include <lcd.h>
#include <mmc.h>
#include <net.h>
#include <netdev.h>
#include <spi.h>
#include <version.h>
#include <asm/io.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/atmel_pio4.h>
#include <asm/arch/atmel_mpddrc.h>
#include <asm/arch/atmel_usba_udc.h>
#include <asm/arch/atmel_sdhci.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
#include <asm/arch/sama5_sfr.h>
#include <asm/arch/sama5d2.h>
#include <asm/arch/sama5d3_smc.h>
DECLARE_GLOBAL_DATA_PTR;
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
return bus == 0 && cs == 0;
}
void spi_cs_activate(struct spi_slave *slave)
{
atmel_pio4_set_pio_output(AT91_PIO_PORTA, 17, 0);
}
void spi_cs_deactivate(struct spi_slave *slave)
{
atmel_pio4_set_pio_output(AT91_PIO_PORTA, 17, 1);
}
static void board_spi0_hw_init(void)
{
atmel_pio4_set_a_periph(AT91_PIO_PORTA, 14, 0);
atmel_pio4_set_a_periph(AT91_PIO_PORTA, 15, 0);
atmel_pio4_set_a_periph(AT91_PIO_PORTA, 16, 0);
atmel_pio4_set_pio_output(AT91_PIO_PORTA, 17, 1);
at91_periph_clk_enable(ATMEL_ID_SPI0);
}
static void board_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct atmel_sfr *sfr = (struct atmel_sfr *)ATMEL_BASE_SFR;
at91_periph_clk_enable(ATMEL_ID_HSMC);
writel(AT91_SFR_EBICFG_DRIVE0_HIGH |
AT91_SFR_EBICFG_PULL0_NONE |
AT91_SFR_EBICFG_DRIVE1_HIGH |
AT91_SFR_EBICFG_PULL1_NONE, &sfr->ebicfg);
/* Configure SMC CS3 for NAND */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(1),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(2) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
&smc->cs[3].cycle);
writel(AT91_SMC_TIMINGS_TCLR(2) | AT91_SMC_TIMINGS_TADL(7) |
AT91_SMC_TIMINGS_TAR(2) | AT91_SMC_TIMINGS_TRR(3) |
AT91_SMC_TIMINGS_TWB(7) | AT91_SMC_TIMINGS_RBNSEL(3) |
AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_8 |
AT91_SMC_MODE_TDF_CYCLE(3),
&smc->cs[3].mode);
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 0, 0); /* D0 */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 1, 0); /* D1 */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 2, 0); /* D2 */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 3, 0); /* D3 */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 4, 0); /* D4 */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 5, 0); /* D5 */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 6, 0); /* D6 */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 7, 0); /* D7 */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 12, 0); /* RE */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 8, 0); /* WE */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 9, 1); /* NCS */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 21, 1); /* RDY */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 10, 1); /* ALE */
atmel_pio4_set_f_periph(AT91_PIO_PORTA, 11, 1); /* CLE */
}
static void board_usb_hw_init(void)
{
atmel_pio4_set_pio_output(AT91_PIO_PORTA, 28, 1);
}
static void board_gmac_hw_init(void)
{
atmel_pio4_set_f_periph(AT91_PIO_PORTB, 14, 0); /* GTXCK */
atmel_pio4_set_f_periph(AT91_PIO_PORTB, 15, 0); /* GTXEN */
atmel_pio4_set_f_periph(AT91_PIO_PORTB, 16, 0); /* GRXDV */
atmel_pio4_set_f_periph(AT91_PIO_PORTB, 17, 0); /* GRXER */
atmel_pio4_set_f_periph(AT91_PIO_PORTB, 18, 0); /* GRX0 */
atmel_pio4_set_f_periph(AT91_PIO_PORTB, 19, 0); /* GRX1 */
atmel_pio4_set_f_periph(AT91_PIO_PORTB, 20, 0); /* GTX0 */
atmel_pio4_set_f_periph(AT91_PIO_PORTB, 21, 0); /* GTX1 */
atmel_pio4_set_f_periph(AT91_PIO_PORTB, 22, 0); /* GMDC */
atmel_pio4_set_f_periph(AT91_PIO_PORTB, 23, 0); /* GMDIO */
at91_periph_clk_enable(ATMEL_ID_GMAC);
}
static void board_uart0_hw_init(void)
{
atmel_pio4_set_c_periph(AT91_PIO_PORTB, 26, 1); /* URXD0 */
atmel_pio4_set_c_periph(AT91_PIO_PORTB, 27, 0); /* UTXD0 */
at91_periph_clk_enable(CONFIG_USART_ID);
}
int board_early_init_f(void)
{
at91_periph_clk_enable(ATMEL_ID_PIOA);
at91_periph_clk_enable(ATMEL_ID_PIOB);
at91_periph_clk_enable(ATMEL_ID_PIOC);
at91_periph_clk_enable(ATMEL_ID_PIOD);
board_uart0_hw_init();
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_ATMEL_SPI
board_spi0_hw_init();
#endif
#ifdef CONFIG_NAND_ATMEL
board_nand_hw_init();
#endif
#ifdef CONFIG_MACB
board_gmac_hw_init();
#endif
#ifdef CONFIG_CMD_USB
board_usb_hw_init();
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
at91_udp_hw_init();
#endif
return 0;
}
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_MACB
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC, 0x00);
if (rc)
printf("GMAC register failed\n");
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
usba_udc_probe(&pdata);
#ifdef CONFIG_USB_ETH_RNDIS
usb_eth_initialize(bis);
#endif
#endif
return rc;
}
/* SPL */
#ifdef CONFIG_SPL_BUILD
void spl_board_init(void)
{
#ifdef CONFIG_SPI_BOOT
board_spi0_hw_init();
#endif
#ifdef CONFIG_NAND_BOOT
board_nand_hw_init();
#endif
}
static void ddrc_conf(struct atmel_mpddrc_config *ddrc)
{
ddrc->md = (ATMEL_MPDDRC_MD_DBW_32_BITS | ATMEL_MPDDRC_MD_DDR3_SDRAM);
ddrc->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
ATMEL_MPDDRC_CR_NR_ROW_14 |
ATMEL_MPDDRC_CR_CAS_DDR_CAS5 |
ATMEL_MPDDRC_CR_DIC_DS |
ATMEL_MPDDRC_CR_DIS_DLL |
ATMEL_MPDDRC_CR_NB_8BANKS |
ATMEL_MPDDRC_CR_DECOD_INTERLEAVED |
ATMEL_MPDDRC_CR_UNAL_SUPPORTED);
ddrc->rtr = 0x511;
ddrc->tpr0 = ((6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET) |
(3 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET) |
(4 << ATMEL_MPDDRC_TPR0_TWR_OFFSET) |
(9 << ATMEL_MPDDRC_TPR0_TRC_OFFSET) |
(3 << ATMEL_MPDDRC_TPR0_TRP_OFFSET) |
(4 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET) |
(4 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET) |
(4 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET));
ddrc->tpr1 = ((27 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET) |
(29 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET) |
(0 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET) |
(3 << ATMEL_MPDDRC_TPR1_TXP_OFFSET));
ddrc->tpr2 = ((0 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET) |
(0 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET) |
(0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET) |
(4 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET) |
(7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET));
}
void mem_init(void)
{
struct atmel_mpddr *mpddrc = (struct atmel_mpddr *)ATMEL_BASE_MPDDRC;
struct atmel_mpddrc_config ddrc_config;
u32 reg;
ddrc_conf(&ddrc_config);
at91_periph_clk_enable(ATMEL_ID_MPDDRC);
at91_system_clk_enable(AT91_PMC_DDR);
reg = readl(&mpddrc->io_calibr);
reg &= ~ATMEL_MPDDRC_IO_CALIBR_RDIV;
reg |= ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_55;
reg &= ~ATMEL_MPDDRC_IO_CALIBR_TZQIO;
reg |= ATMEL_MPDDRC_IO_CALIBR_TZQIO_(100);
writel(reg, &mpddrc->io_calibr);
writel(ATMEL_MPDDRC_RD_DATA_PATH_SHIFT_TWO_CYCLE,
&mpddrc->rd_data_path);
ddr3_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddrc_config);
writel(0x3, &mpddrc->cal_mr4);
writel(64, &mpddrc->tim_cal);
}
void at91_pmc_init(void)
{
at91_plla_init(AT91_PMC_PLLAR_29 |
AT91_PMC_PLLXR_PLLCOUNT(0x3f) |
AT91_PMC_PLLXR_MUL(82) |
AT91_PMC_PLLXR_DIV(1));
at91_pllicpr_init(0);
at91_mck_init(AT91_PMC_MCKR_H32MXDIV |
AT91_PMC_MCKR_PLLADIV_2 |
AT91_PMC_MCKR_MDIV_3 |
AT91_PMC_MCKR_CSS_PLLA);
}
#endif

View File

@ -1,7 +1,7 @@
if TARGET_SAMA5D2_PTC
if TARGET_SAMA5D2_PTC_EK
config SYS_BOARD
default "sama5d2_ptc"
default "sama5d2_ptc_ek"
config SYS_VENDOR
default "atmel"
@ -10,6 +10,6 @@ config SYS_SOC
default "at91"
config SYS_CONFIG_NAME
default "sama5d2_ptc"
default "sama5d2_ptc_ek"
endif

View File

@ -0,0 +1,8 @@
SAMA5D2 PTC EK BOARD
M: Wenyou Yang <wenyou.yang@microchip.com>
M: Ludovic Desroches <ludovic.desroches@microchip.com>
S: Maintained
F: board/atmel/sama5d2_ptc_ek/
F: include/configs/sama5d2_ptc_ek.h
F: configs/sama5d2_ptc_ek_mmc_defconfig
F: configs/sama5d2_ptc_ek_nandflash_defconfig

View File

@ -0,0 +1,8 @@
#
# Copyright (C) 2017 Microchip Corporation
# Wenyou Yang <wenyou.yang@microchip.com>
#
# SPDX-License-Identifier: GPL-2.0+
#
obj-y += sama5d2_ptc_ek.o

View File

@ -0,0 +1,130 @@
/*
* Copyright (C) 2017 Microchip Corporation
* Wenyou Yang <wenyou.yang@microchip.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <debug_uart.h>
#include <dm.h>
#include <i2c.h>
#include <nand.h>
#include <version.h>
#include <asm/io.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/atmel_pio4.h>
#include <asm/arch/atmel_mpddrc.h>
#include <asm/arch/atmel_sdhci.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
#include <asm/arch/sama5d2.h>
#include <asm/arch/sama5d2_smc.h>
DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_NAND_ATMEL
static void board_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
at91_periph_clk_enable(ATMEL_ID_HSMC);
/* Configure SMC CS3 for NAND */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(1) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(1),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(2) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(2) | AT91_SMC_PULSE_NCS_RD(3),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
&smc->cs[3].cycle);
writel(AT91_SMC_TIMINGS_TCLR(2) | AT91_SMC_TIMINGS_TADL(7) |
AT91_SMC_TIMINGS_TAR(2) | AT91_SMC_TIMINGS_TRR(3) |
AT91_SMC_TIMINGS_TWB(7) | AT91_SMC_TIMINGS_RBNSEL(3) |
AT91_SMC_TIMINGS_NFSEL(1), &smc->cs[3].timings);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
AT91_SMC_MODE_DBW_8 |
AT91_SMC_MODE_TDF_CYCLE(3),
&smc->cs[3].mode);
atmel_pio4_set_b_periph(AT91_PIO_PORTA, 22, 0); /* D0 */
atmel_pio4_set_b_periph(AT91_PIO_PORTA, 23, 0); /* D1 */
atmel_pio4_set_b_periph(AT91_PIO_PORTA, 24, 0); /* D2 */
atmel_pio4_set_b_periph(AT91_PIO_PORTA, 25, 0); /* D3 */
atmel_pio4_set_b_periph(AT91_PIO_PORTA, 26, 0); /* D4 */
atmel_pio4_set_b_periph(AT91_PIO_PORTA, 27, 0); /* D5 */
atmel_pio4_set_b_periph(AT91_PIO_PORTA, 28, 0); /* D6 */
atmel_pio4_set_b_periph(AT91_PIO_PORTA, 29, 0); /* D7 */
atmel_pio4_set_b_periph(AT91_PIO_PORTB, 2, 0); /* RE */
atmel_pio4_set_b_periph(AT91_PIO_PORTA, 30, 0); /* WE */
atmel_pio4_set_b_periph(AT91_PIO_PORTA, 31, 1); /* NCS */
atmel_pio4_set_b_periph(AT91_PIO_PORTC, 8, 1); /* RDY */
atmel_pio4_set_b_periph(AT91_PIO_PORTB, 0, 1); /* ALE */
atmel_pio4_set_b_periph(AT91_PIO_PORTB, 1, 1); /* CLE */
}
#endif
static void board_usb_hw_init(void)
{
atmel_pio4_set_pio_output(AT91_PIO_PORTB, 12, 1);
}
#ifdef CONFIG_DEBUG_UART_BOARD_INIT
static void board_uart0_hw_init(void)
{
atmel_pio4_set_c_periph(AT91_PIO_PORTB, 26, 1); /* URXD0 */
atmel_pio4_set_c_periph(AT91_PIO_PORTB, 27, 0); /* UTXD0 */
at91_periph_clk_enable(ATMEL_ID_UART0);
}
void board_debug_uart_init(void)
{
board_uart0_hw_init();
}
#endif
#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
#ifdef CONFIG_DEBUG_UART
debug_uart_init();
#endif
return 0;
}
#endif
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_NAND_ATMEL
board_nand_hw_init();
#endif
#ifdef CONFIG_CMD_USB
board_usb_hw_init();
#endif
return 0;
}
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
#define AT24MAC_MAC_OFFSET 0xfa
#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
#ifdef CONFIG_I2C_EEPROM
at91_set_ethaddr(AT24MAC_MAC_OFFSET);
#endif
return 0;
}
#endif

View File

@ -0,0 +1,60 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_SAMA5D2_PTC_EK=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d2_ptc_ek"
CONFIG_DEBUG_UART=y
CONFIG_FIT=y
CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_MMC"
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_CONSOLE_MUX=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMI is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_CMD_I2C=y
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND=y
CONFIG_CMD_USB=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_DM=y
CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_AT91_UTMI=y
CONFIG_AT91_H32MX=y
CONFIG_AT91_GENERIC_CLK=y
CONFIG_DM_GPIO=y
CONFIG_ATMEL_PIO4=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_AT91=y
CONFIG_I2C_EEPROM=y
CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ATMEL=y
CONFIG_DM_ETH=y
CONFIG_MACB=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_AT91PIO4=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART_ATMEL=y
CONFIG_DEBUG_UART_BASE=0xf801c000
CONFIG_DEBUG_UART_CLOCK=82000000
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
CONFIG_TIMER=y
CONFIG_ATMEL_PIT_TIMER=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y

View File

@ -0,0 +1,60 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_SAMA5D2_PTC_EK=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d2_ptc_ek"
CONFIG_DEBUG_UART=y
CONFIG_FIT=y
CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_NANDFLASH"
CONFIG_NAND_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_CONSOLE_MUX=y
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMI is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_CMD_I2C=y
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND=y
CONFIG_CMD_USB=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_DM=y
CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_AT91_UTMI=y
CONFIG_AT91_H32MX=y
CONFIG_AT91_GENERIC_CLK=y
CONFIG_DM_GPIO=y
CONFIG_ATMEL_PIO4=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_AT91=y
CONFIG_I2C_EEPROM=y
CONFIG_DM_MMC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ATMEL=y
CONFIG_DM_ETH=y
CONFIG_MACB=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_AT91PIO4=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART_ATMEL=y
CONFIG_DEBUG_UART_BASE=0xf801c000
CONFIG_DEBUG_UART_CLOCK=82000000
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
CONFIG_TIMER=y
CONFIG_ATMEL_PIT_TIMER=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y

View File

@ -1,33 +0,0 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_SAMA5D2_PTC=y
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_NAND_SUPPORT=y
CONFIG_NAND_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,57600 earlyprintk mtdparts=atmel_nand:6M(bootstrap)ro, 6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=2 root=ubi0:rootfs"
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SPL=y
# CONFIG_CMD_IMI is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_NAND=y
CONFIG_CMD_NAND_TRIMFFS=y
CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
CONFIG_CMD_FAT=y
CONFIG_ENV_IS_IN_NAND=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_MANUFACTURER="Atmel SAMA5D2_PTC"
CONFIG_USB_GADGET_ATMEL_USBA=y
CONFIG_USB_ETHER=y

View File

@ -1,34 +0,0 @@
CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_TARGET_SAMA5D2_PTC=y
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
CONFIG_SPI_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,57600 earlyprintk mtdparts=atmel_nand:6M(bootstrap)ro, 6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=2 root=ubi0:rootfs"
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SPL=y
# CONFIG_CMD_IMI is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_NAND=y
CONFIG_CMD_NAND_TRIMFFS=y
CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
CONFIG_CMD_FAT=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_MANUFACTURER="Atmel SAMA5D2_PTC"
CONFIG_USB_GADGET_ATMEL_USBA=y
CONFIG_USB_ETHER=y

View File

@ -1,114 +0,0 @@
/*
* Configuration settings for the SAMA5D2 PTC Engineering board.
*
* Copyright (C) 2016 Atmel
* Wenyou Yang <wenyou.yang@atmel.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include "at91-sama5_common.h"
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE 0xf801c000
#define CONFIG_USART_ID 24
#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_SYS_SDRAM_SIZE 0x20000000
#define CONFIG_SYS_TIMER_COUNTER 0xf804803c
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_INIT_SP_ADDR 0x210000
#else
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#undef CONFIG_AT91_GPIO
#define CONFIG_ATMEL_PIO4
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
/* SerialFlash */
#ifdef CONFIG_CMD_SF
#define CONFIG_ATMEL_SPI
#define CONFIG_SPI_FLASH_ATMEL
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 30000000
#endif
/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE 0x80000000
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* PMECC & PMERRLOC */
#define CONFIG_ATMEL_NAND_HWECC
#define CONFIG_ATMEL_NAND_HW_PMECC
#endif
/* USB device */
/* Ethernet Hardware */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_MACB_SEARCH_PHY
#ifdef CONFIG_NAND_BOOT
#undef CONFIG_ENV_OFFSET
#undef CONFIG_ENV_OFFSET_REDUND
#undef CONFIG_BOOTCOMMAND
/* u-boot env in nand flash */
#define CONFIG_ENV_OFFSET 0x200000
#define CONFIG_ENV_OFFSET_REDUND 0x400000
#define CONFIG_BOOTCOMMAND "nand read 0x21000000 0xb80000 0x80000;" \
"nand read 0x22000000 0x600000 0x600000;" \
"bootz 0x22000000 - 0x21000000"
#endif
/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x200000
#define CONFIG_SPL_MAX_SIZE 0x10000
#define CONFIG_SPL_BSS_START_ADDR 0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
#define CONFIG_SYS_MONITOR_LEN (512 << 10)
#ifdef CONFIG_SPI_BOOT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
#elif CONFIG_NAND_BOOT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
#endif
#define CONFIG_PMECC_CAP 8
#define CONFIG_PMECC_SECTOR_SIZE 512
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE 0x1000
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_OOBSIZE 224
#define CONFIG_SYS_NAND_BLOCK_SIZE 0x40000
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
#endif

View File

@ -0,0 +1,46 @@
/*
* Configuration file for the SAMA5D2 PTC EK Board.
*
* Copyright (C) 2017 Microchip Technology Inc.
* Wenyou Yang <wenyou.yang@microchip.com>
* Ludovic Desroches <ludovic.desroches@microchip.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include "at91-sama5_common.h"
#undef CONFIG_SYS_AT91_MAIN_CLOCK
#define CONFIG_SYS_AT91_MAIN_CLOCK 24000000 /* from 24 MHz crystal */
#define CONFIG_MISC_INIT_R
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE 0x20000000
#define CONFIG_SYS_SDRAM_SIZE 0x20000000
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
/* NAND Flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE BIT(21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE BIT(22)
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* PMECC & PMERRLOC */
#define CONFIG_ATMEL_NAND_HWECC
#define CONFIG_ATMEL_NAND_HW_PMECC
#endif
#endif /* __CONFIG_H */