Add kernel doc to the phy_read/write utility functions in phy.h
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
There are devices accesible through mdio clause-45, such as
retimers, that do not have PMA or PCS blocks.
This patch adds MDIO_MMD_VEND1 on the list of device addresses
where phyid is searched. Previous order of devices was kept.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
This is a WAR for DHCP failure after rebooting from the L4T kernel. The
r8169.c kernel driver is setting bit 19 of the rt816x HW register 0xF0,
which goes by FuncEvent and MISC in various driver source/datasheets.
That bit is called RxDv_Gated_En in the r8169.c kernel driver. Clear it
here at the end of probe to ensure that U-Boot can get an IP assigned
via DHCP.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Linux commit 232ba3a51cc2 ('net: phy: Micrel KSZ8061: link failure after
cable connect') implements a fix for the above errata.
This patch replicates that errata fix in an ksz8061 specific init routine.
Signed-off-by: Bryan O'Donoghue <bod@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Drop the example, for two reasons. First, it is tapping directly into
the IO accessors of the SMC911x, while it should instead go through
the net device API. Second, this makes conversion of the SMC911x driver
to DM real hard.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If 'CONFIG_CMD_TFTPBOOT' or 'CONFIG_CMD_BOOTP' are disabled, the usage must be disabled, too!
Signed-off-by: Olaf Krebs <olaf.krebs@emh-metering.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
This documents the u-boot installation procedure and the
hardware in order to get started.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
[trini: Add MAINTAINERS entry for doc file per Soeren's request]
This keeps the compatibility with the old bootcmd.
The fdtfile environment variable also needed to be set to
imx6q-tbs2910.dtb to enable booting mainline kernels
otherwise with extlinux.conf it tries to load
mx6-tbs2910.dtb instead.
With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola
GNU/Linux distribution, we have the following size
differences:
- text: +2041 bytes
- data: 0 bytes
- bss: 0 bytes
- total: +2041 bytes
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
This is needed to enable distro_boot support later on.
Adding the necessary configuration to enable booting general
purpose distributions is typically done by enabling
CONFIG_DISTRO_DEFAULTS.
However the resulting image size is is already very close to
the size limit and PXE isn't strictly needed, so instead we
made sure that all the configuration selected by
CONFIG_DISTRO_DEFAULTS were selected, with the exception of
PXE related configuration (CONFIG_BOOTP_PXE and
CONFIG_CMD_PXE) that are both disabled.
With arm-linux-gnueabi-gcc 9.3.0-1 from the Parabola
GNU/Linux distribution, we have the following size
differences:
- text: +7526 bytes
- data: +28 bytes
- bss: -12 bytes
- total: +7542 bytes
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
This doesn't affect the size of the image: with
arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola GNU/Linux
distribution, the text, data, bss and total sizes remain
unchanged.
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Reviewed-by: Soeren Moch <smoch@web.de>
As that the resulting image is already very close to the
size limit, and that CONFIG_GZIP is not strictly required,
removing it shouldn't hurt.
With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola
GNU/Linux distribution we have the following size
reduction:
- text: 9752
- data: 0
- bss: 16
- total: 9768
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Acked-by: Soeren Moch <smoch@web.de>
The loadb and loads commands are not needed for booting.
There are also more reliable and faster alternatives to
loadb and loads that can be used with the current configuration.
As that the resulting image is already very close to the
size limit, removing the loadb and loads commands shouldn't
hurt.
With arm-linux-gnueabi-gcc 9.2.0-1 from the Parabola
GNU/Linux distribution we have the following size
reduction:
- text: 6733 bytes
- data: 116 bytes
- bss: 1172 bytes
- total: 8021 bytes
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org>
Acked-by: Soeren Moch <smoch@web.de>
The current recommendation for best security practice from the US government
is to use SHA384 for TOP SECRET [1].
This patch adds support for SHA384 and SHA512 in the hash command, and also
allows FIT images to be hashed with these algorithms, and signed with
sha384,rsaXXXX and sha512,rsaXXXX
The SHA implementation is adapted from the linux kernel implementation.
[1] Commercial National Security Algorithm Suite
http://www.iad.gov/iad/programs/iad-initiatives/cnsa-suite.cfm
Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
This displays incorrect data at present due to a missing header file
in display_options. Fix it.
Fixes: 0914011310 ("command: Remove the cmd_tbl_t typedef")
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable CONFIG_PCI and CONFIG_NVME and related configs for the
Pinebook Pro.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With recently added changes we get support for usb3 including handling
of the phys (type-c and inno-usb2), so enable the necessary config
options on puma.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the current usb stack in u-boot, all host ports on puma work
flawlessly without any additional special handling, so drop that
usb hub hacking from the puma board.
Tested with mass-storage and usb-ethernet on both usb3 and usb2 ports.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The introduction of the puma-specific generator was mainly a way
to split the pmu firmware from the ATF binary and not having to
distribute that 4GB (sparse) image that was created before moving
to the bl31.elf as base.
Looking at the publically available repository for that separate
pmu firmware
https://git.theobroma-systems.com/rk3399-cortex-m0.git/
there is also no activity for 3 years and apart from some build
customizations no other changes were done.
And even then, if changes need to be made, this can very well also
happen in the atf context itself, so there is no real need to
diverge from the established build procedure and we can just go
back to using the main make_fit_atf.py script.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
So far the puma dts files only just included the main puma dtsi without
handling the actual baseboard and rk3399-puma.dtsi was very much
detached from the variant in the mainline Linux kernel.
Recent changes resulted in a strange situation with nonworking puma boards.
Commit ab800e5a6f ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi")
moved the sdram include from rk3399-puma-ddrX.dts to new files
rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though.
Commit 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
replaced the rk3399-puma.dtsi nearly completely, but in the kernel
it definitly depends on a baseboard dts to actually enable peripherals
like sd-slot, uarts, etc.
So to untagle this and bring the whole thing more in line with mainline
Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate
DDR-option devicetrees and instead replace them with a puma Kconfig option
to select and include the needed DDR variant.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit moving puma to the generic cpuid/macaddr helpers used 7 spaces
as indentation, so correct that by moving to the required tabs.
Fixes: fa177ff020 ("board: puma: Use rockchip_* helpers to setup cpuid and macaddr")
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tabs not spaces, so transform it to the common styling.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The regulator enable-gpio uses opposite values for the declaration
vs. the enable_active_low property, breaking the regulator enablement.
Make the usbhost-supply work again by bringing them in sync again.
This mimics the upstream Linux change found on:
http://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The gmac reset has opposite values for the gpio declaration
and the separate reset-active, bring this in line to make
u-boot also find the ethernet-phy.
This mimics the upstream Linux commit found on
https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Board has flash chip on board so let store U-Boot environment there.
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Document SPI flash program steps for rockchip platforms.
Suggested-by: Hugh Cole-Baker <sigmaris@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Mark the default U-Boot environment as SPI flash since
this is an on board flash device.
Updated env offset, size in contrast with default since
the U-Boot proper has to start from 384K.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On rockchip platforms, SPI boot image creation is not
straightforward like MMC boot image creation where former
requires to specify tpl, spl in multimage format in mkimage,
and later simply do a concatenate mkimaged-tpl with spl.
On this note, let drop rkspi image type creation via kbuild
and let inform via rockchip.rst
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The 'stdout-path' is missing after dts sync.
Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.
Net - Dual ethernet port, 1 X Gbe, 1 X 100M
USB - USB 3.0
DC - USB-Type C, 5V 2A
Storage - TF card, eMMC
Just build idbloader.img and u-boot.itb for Rockpi E board and
follow the blow steps to replace the relevant partition.
dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc
Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
Enable CONFIG_PCI and CONFIG_NVME and related configs for the
ROCKPro64 board.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable CONFIG_PCI and CONFIG_NVME and related configs for the
Firefly RK3399 board.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The following problems are resolved:
* When booting via UEFI an SMBIOS table is presented to the operating
system. If U-Boot tries to add an empty string, this results in corrupted
SMBIOS information. We will now use "Unknown" as property value.
* The EFI_RNG_PROTOCOL uses the DM_RNG drivers. For the virtio RNG driver
the missing DM_RNG Kconfig dependency is added.
* Missing function descriptions for the EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL are
added.
-----BEGIN PGP SIGNATURE-----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=tmqF
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc4-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc4 (2)
The following problems are resolved:
* When booting via UEFI an SMBIOS table is presented to the operating
system. If U-Boot tries to add an empty string, this results in corrupted
SMBIOS information. We will now use "Unknown" as property value.
* The EFI_RNG_PROTOCOL uses the DM_RNG drivers. For the virtio RNG driver
the missing DM_RNG Kconfig dependency is added.
* Missing function descriptions for the EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL are
added.
Add the missing Kconfig dependency and let VIRTIO_RNG default to yes.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
smbios_add_string() cannot deal with empty strings. This leads to incorrect
property values and invalid tables. E.g. for the pine64-lts_defconfig
CONFIG_SMBIOS_MANUFACTURER="". Linux command dmidecode shows:
Table 1:
Manufacturer: sunxi
Product Name: sunxi
Table 3:
Invalid entry length (2). DMI table is broken! Stop.
Replace empty strings by "Unknown".
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Resync checkpatch.pl (largely) with v5.7 and introduce U-Boot specific
checks in a localized area, so they aren't lost in the future.
- Complete / re-migrate some options from config headers to defconfigs
- Add dependencies to the various debug uart drivers
All of our cmds have a Kconfig entry. Making enabling a CMD via the
config file an error to checkpatch.pl.
Signed-off-by: Tom Rini <trini@konsulko.com>
There is a lot of use of #ifdefs in U-Boot. In an effort reduce this,
suggest using the compile-time construct.
Signed-off-by: Simon Glass <sjg@chromium.org>
A common problem when submitting a new uclass is to forget to add sandbox
tests. Add a warning for this.
Of course tests should always be added for new code, but this one seems to
be missed by nearly every new contributor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an option to indicate that U-Boot-specific checks should be enabled.
Add a function to house the code that will be added.
Signed-off-by: Simon Glass <sjg@chromium.org>
