The AMCC Luan now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.
This patch also enables the cache in FLASH for the startup
phase of U-Boot (while running from FLASH). After relocating to
SDRAM the cache is disabled again. This will speed up the boot
process, especially the SDRAM setup, since there are some loops
for memory testing (auto calibration).
Signed-off-by: Stefan Roese <sr@denx.de>
The AMCC Yucca now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.
Signed-off-by: Stefan Roese <sr@denx.de>
Define CONFIG_PROG_SDRAM_TLB so that the TLB entries for the
DDR memory are dynamically programmed matching the total size
of the equipped memory (DIMM modules).
Signed-off-by: Stefan Roese <sr@denx.de>
The config value for:
* CFG_ACR_PIPE_DEP
* CFG_ACR_RPTCNT
* CFG_SPCR_TSEC1EP
* CFG_SPCR_TSEC2EP
* CFG_SCCR_TSEC1CM
* CFG_SCCR_TSEC2CM
Were not being used when setting the appropriate register
Added:
* CFG_SCCR_USBMPHCM
* CFG_SCCR_USBDRCM
* CFG_SCCR_PCICM
* CFG_SCCR_ENCCM
To allow full config of the SCCR.
Also removed random CFG_SCCR settings in MPC8349EMDS, TQM834x, and sbc8349
that were just bogus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8360E rev2.0 have new spridr,and PVR value,
The MDS board for MPC8360E rev2.0 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
MPC8349E rev3.1 have new spridr,and PVR value,
The MDS board for MPC8349E rev3.1 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo<X.Xie@freescale.com>
Add support for the MPC8349E-mITX-GP, a stripped-down version of the
MPC8349E-mITX. Bonus features include support for low-boot (BMS bit in
HRCW is 0) for the ITX and a README for the ITX and the ITX-GP.
Signed-off-by: Timur Tabi <timur@freescale.com>
The patch solves the alignment problem of the local bus access windows to
render accessible the memory bank and PHY registers of UPC 1 (starting at
0xf801 0000). What we actually did was to adjust the sizes of the bus
access windows so that the base address alignment requirement would be met.
Signed-off-by: Chereji Marian <marian.chereji@freescale.com>
Signed-off-by: Gridish Shlomi <gridish@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
I've redone the SBC8349 support to match git-current, which
incorporates all the MPC834x updates from Freescale since the 1.1.6
release, including the DDR changes.
I've kept all the SBC8349 files as parallel as possible to the
MPC8349EMDS ones for ease of maintenance and to allow for easy
inspection of what was changed to support this board. Hence the SBC8349
U-Boot has FDT support and everything else that the MPC8349EMDS has.
Fortunately the Freescale updates added support for boards using CS0,
but I had to change spd_sdram.c to allow for board specific settings for
the sdram_clk_cntl (it is/was hard coded to zero, and that remains the
default if the board doesn't specify a value.)
Hopefully this should be mergeable as-is and require no whitespace
cleanups or similar, but if something doesn't measure up then let me
know and I'll fix it.
Thanks,
Paul.
This patch updates the recently added Katmai board support. The biggest
change is the support of ECC DIMM modules in the 440SP(e) SPD DDR2
driver.
Please note, that still some problems are left with some memory
configurations. See the driver for more details.
Signed-off-by: Stefan Roese <sr@denx.de>
Some boards that can have more than 768MBytes of SDRAM need to
set "initrd_high", so that the initrd can be accessed by the
Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
When PCI PNP is enabled the pci pnp configuration routine is called
which sets the PCI_CACHE_SIZE_LINE to 8. This seems to generate some
problems with some PCI cards. For now disable the PCI PNP configuration.
Signed-off-by: Stefan Roese <sr@denx.de>
The config file now handles the 2nd target, the Rainier (440GRx)
evaluation board better. Additionally the PPC input clock was
adjusted to match the correct value of 33.0 MHz.
Signed-off-by: Stefan Roese <sr@denx.de>
Now the AMCC eval boards Yosemite (440EP) and Yellowstone (440GR)
share one config file and all board specific files. This way we
don't have to maintain two different sets of files for nearly
identical boards.
Signed-off-by: Stefan Roese <sr@denx.de>
"mii device" results in "Unexpected exception"). Fixing this properly
requires some clean-up in the FEC drivers infrastructure for ColdFire, so
this commit disables MII commads for now.
The patch by Heiko Schocher <hs@pollux.denx.de> on Jan, 19, 2007
fixes cfi_driver bug for mpc7448hpc2 board. The default cfi_driver can support
mpc7448hpc2 board.
Conflicts:
drivers/cfi_flash.c
The patch by Heiko Schocher <hs@pollux.denx.de> on Jan, 19, 2007
fixes cfi_driver bug for mpc7448hpc2 board. The default cfi_driver can support
mpc7448hpc2 board.
Now the board revision and the current PCI bus speed are printed after
the board message.
Also the EBC initialising is now done via defines in the board config
file.
Signed-off-by: Stefan Roese <sr@denx.de>
Now the board revision and the current PCI bus speed are printed after
the board message.
Also the EBC initialising is now done via defines in the board config
file.
Signed-off-by: Stefan Roese <sr@denx.de>
This update brings the ALPR board support to the newest version.
It also fixes a problem with the NAND driver.
Signed-off-by: Stefan Roese <sr@denx.de>
This code will optimize the DDR2 controller setup on a board specific
basis.
Note: This code doesn't work right now on the NAND booting image for the
Sequoia board, since it doesn't fit into the 4kBytes for the SPL image.
Signed-off-by: Stefan Roese <sr@denx.de>
- fix a typo in V38B config file
- move watchdog initialisation earlier in the boot process
- add "wdt=off" to default kernel command line (disables kernel watchdog)
