Common code should be valid for more than one architecture,
therefore the km82xx specific code was removed from common.c.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
These defines and the header keymile_hdlc_enet.h are obsolete
due to the removed hdlc code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
The debug environment which is stored in textfiles in the
scripts directory was reworked. Two usecase are now present
which can be executed simply from the default environment:
run develop: this configures the environment to setup the
rootfs via nfs
run ramfs: this configures the environment to setup the
rootfs in ram
Each architecture now has a "arch" variable which is used
to load the architecture specific debug scripts and to set
the rootpath for NFS.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
The test SW is started when the test_bank variable is set.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
This is the second step to simplify and decrease the default
environment for the keymile boards. The release usecase formaly
used to set the production environment was removed and the default
configuration is now the production environment. So the formar
environment variable "release" which has done a lot of things
in the past, simply erase the current environment and do a reset
which forces u-boot to setup the default environment again.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
Add detection and initialisation for graphic extension board
and support splash screen when booting. Enable "bmp" command
in the board configuration and provide "disp" command to
be able to switch the display on/off.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
gen10g_startup() had 2 bugs:
1) It had a boolean logic error in checking the MMD mask, and
always checked all of them.
2) It checked devices which don't actually report link state, which
meant that it would never believe the link was fully up.
Fix the boolean logic, and then mask the MMD mask so only link-reporting
devices are checked.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Reported-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Since panic() never returns, we should add an appropriate attribute to
let gcc improve optimization around it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This adds a simple flash test to automatically verify erasing,
writing, and reading of sectors. The code is based on existing
Blackfin tests but generalized for everyone to use.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current arch/driver specific UART posts basically boil down to setting
the UART to loop back mode, then reading and writing data. If we ignore
the loop back part, the rest can be built upon the existing common serial
API. So let's do just that.
First add a call back for serial drivers to implement loop back control.
Then write a post test that walks all of the serial drivers, puts them
into loop back mode, and verifies that reading/writing at all the diff
baud rates is OK.
If a serial driver doesn't support loop back mode (either it can't or
it hasn't done so yet), then skip it. This should allow for people to
easily migrate to the new post test with existing serial drivers.
I haven't touched the few already existing uart post tests as I don't
the hardware or knowledge of converting them over. So I've marked the
new test as weak which will allow the existing tests to override the
default until they are converted.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The multi serial support has a "ctlr" field which almost no one uses,
but everyone is forced to set to useless strings. So punt it.
Funny enough, the only code that actually reads this field (the mpc8xx
driver) has a typo where it meant to look for the SCC driver. Fix it
while converting the check to use the name field.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
For people who want to manually extract the embedded environment so that
it can be manually packed into the final u-boot image, add a config opt
to force building of the envcrc tool.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Once we add a new page_size field for write lengths, we can unify the
write methods for most of the spi flash drivers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If we don't want to build support for any partition types we can now
add #undef CONFIG_PARTITIONS in a board config file to keep this from
being compiled in. Otherwise boards assume this is compiled in by
default
Signed-off-by: Matthew McClintock <msm@freescale.com>
This include is needed, if this memory test is used "outside"
from post code, for example booting with nand_spl, and using
this memory test before copying u-boot code to RAM and jumping
to it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Rather than having a bunch of random commands handle autostart behavior,
unify the logic in a single place. This also fixes building of these
different commands when bootm is disabled.
Acked-by: Matthew McClintock <msm@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We need a TLB entry to call get_ram_size(); the common code doesn't create
one until *after* fixed_sdram() has determined the size. So we set up tlbs
for the max possible size and tear them down once we're done with
get_ram_size(); the common 85xx code will then set up a final set of tlb
entries for the *actual* detected size of ddr.
This prevents us from having TLB entries that are larger than DDR sitting
around for very long, which is not a recommended scenario.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Fman device tree node binding allows for the entire Fman firmware binary
data to be embedded in the device tree. This eliminates the need to have
NOR flash mapped to Linux just so that the Fman driver can see the firmware.
The location of the Fman firmware is taken from the 'fman_ucode' environment
variable.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-mmc:
mmc: rescan fails on empty slot
AT91:mmc:fix multiple read/write error
mmc: Access mode validation for eMMC cards > 2 GiB
mmc: sh_mmcif: add support for Renesas MMCIF
mmc: fix the condition for MMC version 4
MMC: add marvell sdhci driver
MMC: add sdhci generic framework
MMC: add erase function to both mmc and sd
MMC: unify mmc read and write operation
mmc: Tegra2: Enable SD/MMC driver for Seaboard and Harmony
mmc: Tegra2: SD/MMC driver for Seaboard - eMMC on SDMMC4, SDIO on SDMMC3
* 'master' of git://git.denx.de/u-boot-arm:
ARM: MX5: Fix broken leftover TO-2 errata workaround
MX31: Cleanup clock function
scb9328: Add ARM relocation support
am3517evm: change console device from ttyS2 to ttyO2
Remove volatile qualifier in get_ram_size() calls
TI: TNETV107X Fix Build Error
ARM: add missing CONFIG_SKIP_LOWLEVEL_INIT for armv7
arm: add CONFIG_MACH_TYPE setting and documentation
arm: add __ilog2 function
Timer: Fix misuse of ARM *timer_masked() functions outside arch/arm
EfikaMX: Enable EXT2 booting
EfikaMX: Add missing CONFIG_SYS_TEXT_BASE
EfikaMX: Use correct imximage.cfg
MX27: Update to autogenerated asm-offsets.h
MX5: Update to autogenerated asm-offsets.h
imx: Add support for zmx25 board
imx: Make imx25 compatible to mxc_gpio driver and fix in tx25
imx: Add auto generation of asm-offsets.h for imx25
imx: Add support for USB EHCI on imx25
imx: Use correct imx25 reset.c
imx: Add get_tbclk() function for imx25
ARM: Update maintainer of board scb9328
mx27: Make the UART port number explicit
build: Add targets for auto gen of asm-offsets.h and use it in imx35
mx31pdk: cosmetic: Fix line over 80 characters
This patch fixes compiler errors due to missing definitions of
CONFIG_SYS_SDRAM_BASE and CONFIG_SYS_INIT_SP_ADDR.
It also does some cleanup: CONFIG_SYS_TEXT_BASE was moved to scb9328.h,
obsolete config.mk was removed. The scb9328 board has 1 DRAM bank, so don't
ask for more banks. CONFIG_NR_DRAM_BANKS will ever be 1.
Signed-off-by: Torsten Koschorrek <koschorrek@synertronixx.de>
the serial device names have been changed from ttySx to ttyOx, so the
console device name should be also changed to support the latest kernel
versions.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Vaibhav Hiremath<hvaibhav@ti.com>
P2041RDB Specification:
-----------------------
Memory subsystem:
* 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 256 Kbit M24256 I2C EEPROM
* 16 Mbyte SPI memory
* SD connector to interface with the SD memory card
Ethernet:
* dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
* dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
PCIe:
* Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
* Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
I2C:
* I2C1: Real time clock, Temperature sensor, Memory module
* I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch provides handling of the two way handshake when SEND_OP_COND
(CMD1) is send to mmc card. It is necessary to inform eMMC card if the
host can work with high capacity cards (Jedec JESD84-A441, point 7.4.3).
The extra flag MMC_MODE_HC (high capacity) is added to indicate if the
host is capable of handling the high capacity eMMC cards.
Since this change is added to the generic mmc framework, then it requires
other boards to indicate if their mmc controllers can handle high capacity
cards. As it is now - the old behaviour of the framework is preserved.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Nowdays, there are plenty of mmc driver in uboot adopt the sd standard
host design, aka as sdhci. It is better to centralize the common logic
together to better maintenance.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Erase is a very basic function since the begin of sd specification is
announced. Although we could write a bulk of full 0xff memory to the
range to take place of erase, it is more convenient and safe to
implement the erase function itself.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The ePAPR specification says that phandle properties should be called
"phandle", and not "linux,phandle". To facilitate the migration from
"linux,phandle" to "phandle", introduce function fdt_create_phandle(),
which creates a phandle in a given node. For now, we create both the
"phandle" and "linux,phandle" properties. A later version of this
function will remove support for "linux,phandle".
Signed-off-by: Timur Tabi <timur@freescale.com>
Introduce two functions, fdt_verify_alias_address() and
fdt_get_base_address(), which can be used to verify the physical address
of a device in a device tree.
fdt_get_base_address() returns the base address of an SOC or PCI node.
fdt_verify_alias_address() prints a message if the address of a node
specified by an alias does not match the given physical address.
Signed-off-by: Timur Tabi <timur@freescale.com>
For ages, we've been talking about adding functions to libfdt to allow
iteration through properties. So, finally, here are some.
I got bogged down on this for a long time because I didn't want to
expose offsets directly to properties to the callers. But without
that, attempting to make reasonable iteration functions just became
horrible. So eventually, I settled on an interface which does now
expose property offsets. fdt_first_property_offset() and
fdt_next_property_offset() are used to step through the offsets of the
properties starting from a particularly node offset. The details of
the property at each offset can then be retrieved with either
fdt_get_property_by_offset() or fdt_getprop_by_offset() which have
interfaces similar to fdt_get_property() and fdt_getprop()
respectively.
No explicit testcases are included, but we do use the new functions to
reimplement the existing fdt_get_property() function.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This was extracted from the DTC commit:
73dca9ae0b9abe6924ba640164ecce9f8df69c5a Mon Sep 17 00:00:00 2001
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
zmx25 is a board based on imx25 SoC, 64 Megs of LPDDR, 32 Megs of NOR flash, an
optional NAND flash.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
This erratum doesn't exist on this processor, and the workaround
spins on a non-existent register, causing boot to hang.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For only ~150 bytes increase in size, we can get a nice flash progress
indicator rather than just the boring dots (which don't tell too much
about overall progress). So enable it for all ADI boards.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These boards have an mmc/sd slot on them connected over SPI, so
enable the driver.
Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These boards can have an addon card plugged onto them, so enable
support for it.
Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Set the default post word location to an L1 data location for all
Blackfin parts so things "just work" for most people.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This brings CONFIG_SERIAL_MULTI support to the Blackfin on-chip UARTs.
Ends up adding only ~512bytes per additional UART.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Move to use hwconfig for usb mode & phy type instead of magic
'usb_phy_type' environment variable on the following platforms:
MPC8536DS, P1020RDB, P1020RDB-PC, P1010RDB, P2020RDB, P2020RDB-PC,
P2020RDB, P3041DS, P4080DS, & P5020DS.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable buffer write for better performance. This platform uses a NOR flash
chip which supports write buffer programming. CFI driver can query the
buffer size and use it to program the flash for best performance.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023RDS board is the reference board for the P1023 SoC.
Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe,
UART, I2C, etc.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When booting from NAND we get the environment and FMan ucode from NAND.
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove an empty board_early_init_f() from the MPC8323ERD and MPC360ERDK boards.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Includes board config file, documentation, maintainer and boards.cfg
entries, and board specific files in vendor dir.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch add support for the Network Space v2 board and parents, based
on the Marvell Kirkwood 6281 SoC. This include Network Space (Max) v2
and Internet Space v2.
Additional information is available at:
http://lacie-nas.org/doku.php?id=network_space_v2
Signed-off-by: Simon Guinot <sguinot@lacie.com>
This adds support for the keymile Kirkwood BEC portl2 board. This board
relies on the km_arm (km_kirkwood) BEC.
The egiga driver is configured for a 100M full-duplex, A/N off connnection
to the backplane. This board has always ethernet present, because it is
connected to the marvell switch similar to mgcoge3un. The reset_phy
functionality is also the same to mgcoge3un.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
suen3 and suen8 were in first HW version quite different, but
now they are from a u-boot point of view similar. So these
two boards can use the same header file. Other keymile boards
differ only in the usage of the PCI interface. Therefore
a target km_kirkwood_pci was introduced. All targets use
the same header file.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
This is defined for all km_kirkwood boards and was not used up to now.
This value was the same for all boards but it could be changed for some
boards (and thus needs to be defined for every board).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
CONFIG_ENV_SIZE for NAND was later in this file overwritten
because we have the environment in i2c eeprom, so remove
this define.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
commit 010a958b
(arm/km: remove CONFIG_SYS_KWD_CONFIG from keymile-common.h)
breaks building keymile arm targets, when u-boot.kwb tries to
generate the binary with mkimage. A simple make <board> or MAKEALL
succeeded because it don't try to build the kirwood binary at the end.
Due this commit we use the CONFIG_SYS_KWD_CONFIG from the
arch-kirkwood/config.h and it was removed from the board config.
But it was forgotten to include the header. Now the header is included
in km_arm.h. Some other defines were obsolete due to this include,
these are also removed in this commit.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
This patch removes the board implemenatation for flash driver which can now
safely switched to the common cfi driver.
Compile tested for all atstk100x boards, runtime tested on atstk1002.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
This patch enables the new clock features from arm920t/at91/clock.c. This
is an required step to get at91rm9200_usart replaced by atmel_usart driver.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Jens Scharsig <js_at_ng@scharsoft.de>
Cc: Eric Bénard <eric@eukrea.com>
Enable dcache and arch memset/memcpy for speed reasons
Remove of config.mk and some environment overwrites
Some generic cleanup
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Define CONFIG_SYS_SDRAM_BASE to physical SDRAM address
and CONFIG_SYS_INIT_SP_ADDR to physical SRAM address
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Replace the cache related CONFIG flags with more meaningful
names. Following are the changes:
CONFIG_L2_OFF -> CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_NO_ICACHE -> CONFIG_SYS_ICACHE_OFF
CONFIG_SYS_NO_DCACHE -> CONFIG_SYS_DCACHE_OFF
Signed-off-by: Aneesh V <aneesh@ti.com>
V2:
* Changed CONFIG_L2_OFF -> CONFIG_SYS_NO_L2CACHE
V4:
* Changed all three flags to the final names suggested as above
and accordingly changed the commit message
- Add a framework for layered cache maintenance
- separate out SOC specific outer cache maintenance from
maintenance of caches known to CPU
- Add generic ARMv7 cache maintenance operations that affect all
caches known to ARMv7 CPUs. For instance in Cortex-A8 these
opertions will affect both L1 and L2 caches. In Cortex-A9
these will affect only L1 cache
- D-cache operations supported:
- Invalidate entire D-cache
- Invalidate D-cache range
- Flush(clean & invalidate) entire D-cache
- Flush D-cache range
- I-cache operations supported:
- Invalidate entire I-cache
- Add maintenance functions for TLB, branch predictor array etc.
- Enable -march=armv7-a so that armv7 assembly instructions can be
used
Signed-off-by: Aneesh V <aneesh@ti.com>
Add a flag to nand_read_skip_bad() such that if true, any trailing
pages in an eraseblock whose contents are entirely 0xff will be
dropped.
The implementation is via a new drop_ffs() function which is
based on the function of the same name from the ubiformat
utility by Artem Bityutskiy.
This is as-per the reccomendations of the UBI FAQ [1]
[1] http://www.linux-mtd.infradead.org/doc/ubi.html#L_flasher_algo
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Artem Bityutskiy <dedekind1@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When specified in the flags argument of nand_write, WITH_YAFFS_OOB causes an
operation which is mutually exclusive with the 'usual' way of writing.
Add a check that client code does not specify WITH_YAFFS_OOB along with any
other flags and add a comment indicating that the WITH_YAFFS_OOB flag should
not be mixed with other flags.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
In a future commit the behaviour of nand_write_skip_bad()
will be further extended.
Convert the only flag currently passed to the nand_write_
skip_bad() function to a bitfield of only one allocated
member. This should avoid an explosion of int's at the
end of the parameter list or the ambiguous calls like
nand_write_skip_bad(info, offset, len, buf, 0, 1, 1);
nand_write_skip_bad(info, offset, len, buf, 0, 1, 0);
Instead there will be:
nand_write_skip_bad(info, offset, len, buf, WITH_YAFFS_OOB |
WITH_OTHER);
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
* 'master' of git://git.denx.de/u-boot-arm:
run arm_pci_init after relocation
IXP42x PCI rewrite
update/fix PDNB3 board
update/fix IXDP425 / IXDPG425 boards
add dvlhost (dLAN 200 AV Wireless G) board
IXP NPE: add support for fixed-speed MII ports
update/fix AcTux4 board
update/fix AcTux3 board
update/fix AcTux2 board
update/fix AcTux1 board
use -ffunction-sections / --gc-sections on IXP42x
support CONFIG_SYS_LDSCRIPT on ARM
fix "depend" target in npe directory
Fix IXP code to work after relocation was added
trigger hardware watchdog in IXP42x serial driver
add support for IXP42x Rev. B1 and newer
add XScale sub architecture (IXP/PXA) to maintainer list
Conflicts:
arch/arm/lib/board.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it. Drop it.
This includes support for VFD displays which have always been used by
this board only.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add support for Bluewater Systems AT91 based Snapper 9260 and 9G20
single board computer modules. Includes NAND flash and Ethernet
support.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
* convert at91rm9200ek and eb_cpux9k2 board to ATMEL_xxx name scheme
* Fix: timer.c compile error io.h not found with arm/at91rm9200
* update arm920t/at91 to ATMEL_xxx name scheme
* update arm920t/at91 soc lib
* update at91_emac driver
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Tested-by: Andreas Bießmann <andreas.devel@gmail.com>
* 'master' of git://git.denx.de/u-boot-arm:
SMDK6400: fix the compiler error
imx27lite: Remove local config.mk
mx31ads: Fix environment location on flash
imx31_litekit: Remove local config.mk
mx31litekit: Fix boot with the new relocation scheme.
mx31ads: Use the new relocation scheme
Local board config.mk should be avoided.
Place CONFIG_SYS_TEXT_BASE definition into the board config file instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
At the moment u-boot and u-boot environment on flash
have overlapping addresses, so each u-boot update erases
the environment. Fix this by placing evironment right
after u-boot. Also, remove confusing comment about environment
location.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Local board config.mk should be avoided.
Place CONFIG_SYS_TEXT_BASE definition into the board config file instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
imx31_litekit has been converted to the new relocation scheme, but it does not boot.
Make the boot functional by using board_early_init_f .
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
This fixes the MX31ADS build by using the new relocation scheme.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Felix Radensky <felix@embedded-sol.com>
The recent commit ea882baf9c broke embedding environments in the middle
of a sector, so relocate it to the start of the 2nd sector.
Signed-off-by: Harald Krapfenbauer <harald.krapfenbauer@bluetechnix.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Relocate the env to one of the small end sectors to avoid issues with
embedding it, such as support being broken (by recent commit ea882baf9c),
and for taking a while to save updates.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Minimal platform support to boot linux from SD.
Supported devices/hw limited to external MMC/SD slot,
GPIO, I2C and minimal PRCMU.
Signed-off-by: John Rigby <john.rigby@linaro.org>
CC: Albert Aribaud <albert.aribaud@free.fr>
We change default settings for egiga on mgcoge3un.
The reason we need this is that we have the gig port on mgcoge3un
connected using a back-to-back pair of PHYs. There are no magnetics and
because of that the port has to be run with a fixd configuration and
auto-negotiation must be disabled. In the default mode the egiga driver
uses autoneg to determine port speed - which defaults to 1G (we need
100M full duplex).
Add wait for the GPIO line connected to mgcoge3ne before
starting mgcoge3un. A board specific ethernet present function
was added, because on this board ethernet is always present.
The BOCO FPGA access was enhanced and changed to use register
definitions.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The mgcoge2un target was only an intermediate step to mgcoge3un.
For this reason the mgcoge2un support was moved to mgcoge3un,
because it isn't needed to support both targets.
We add the BootROM init file for the mgcoge3un memphis RAM.
We also move the suen3 and suen8 boards into the correct category
in the MAINTAINERS file.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This is not supported on our km-arm boards since we have defined
CONFIG_SYS_NO_FLASH for our NAND Flash chip.
With CONFIG_CMD_JFFS2, the ls command is present and works very badly
on our km-arm boards.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
This environment variable is used to set the bootcount address
for the kernel.
last_stage_init is not available for arm platforms. So the
calls to set_km_var and set_bootcount_addr are done in
misc_init_r.
Additionally some unneeded printouts were removed.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Since all the boards define the same env settings, this simplifies
the board files.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This define is marvell specific, so it should be present in km_arm.
It is however not needed there either, since we set it to the default
value that is already set in include/asm/arch-kirkwood/config.h
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much
similar to S5PC210.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
commit ed59e58 (Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZ) made the
definition of CONFIG_SYS_BOOTMAPSZ unnecessary.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <jason.hui@linaro.org>
config.mk should not be used in board directory and should be removed.
Use the same approach for building the image as other MX51/MX53 boards.
After this change vision2 board can be built again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch add initial support for freescale MX53LOCO board.
Network(FEC),SD/MMC,UART have been supported by this patch
Signed-off-by: Jason Liu <jason.hui@linaro.org>
With the following commit, CONFIG_OF_LIBFDT is redefined.
2fa8ca98c3
Add CONFIG_OF_LIBFDT to more boards.
Remove the duplicated definition to fix CONFIG_OF_LIBFDT redefined
warning.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since the following commit, definition CONFIG_SYS_BOOTMAPSZ is not
needed any more.
ed59e58786
Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZ
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/85xx: add support for env in MMC/SPI on corenet ds boards
powerpc/85xx: Enable eSPI support on corenet ds boards
The pnvram size was used later from start scripts in linux. Therefore
it was added to the default environment.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
This is a first step to simplify the default environment. Move all
the environment variables which are only needed for debugging
purpose to textfiles in the scripts directory. In case of debugging
these files can be loaded via tftp into RAM and set via the env import
command. Other variables are identified as obsolete and were removed.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
BoardId and HWKey are used to identify the HW class of a given board.
The correct values are stored in the inventory eeprom. During creation
time of a boot package the boardId and HWkey for the SW is stored in
the default environment and burned into the flash. During boottime
the values in the inventory and in the environment are compared to
avoid starting of a SW which is not authorized for this board.
Some bootpackages are allowed to run on a set of different boardId
hwKey. In this case the environment variable boardIdListHex was added
to the default environment. In this case the command iterates over the
pair values and compares them with the values read from the inventory
eeprom.
The syntax of such a boardIdListHex value is e.g.: 158_1 159_1 159_2
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
For emmc, it may have up to 7 partitions: two boot partitions, one
user partition, one RPMB partition and four general purpose partitions.
(Refer to JESD84-A44.pdf/page 154)
As bootloader may need to read out or reflashing images on those
different partitions, it is better to enable the partition switch with
console command support.
Also for partition would be restore to user partition(part 0) when CMD0
is used, so change mmc_init routine to perform normal initialization
only once for each slot, unless use the rescan command to force init
again.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
A "send status" command is added with the commit "mmc: checking
status after commands with R1b response". But the status register
returned from send status command of SPI protocol is different from
that of MMC/SD protocol. We do a simple test and generate a response
in stead of full bit-by-bit translation.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
The otc570 board support was broken. Within this opportunity, I completely
reworked the board files.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
ftahbc020s.h provides basic definitions of this controller
to help a SoC which use this AHB Controller could
do scalable software settings in lowlevel_init.S.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
as checkpatch proposes to use strict_strtoul instead of
simple_strtoul, introduce it.
Ported this function from Linux 2.6.38 commit ID:
521cb40b0c44418a4fd36dc633f575813d59a43d
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This is needed for the upcoming TFTP server implementation.
This also simplifies PingHandler() and fixes rxhand_f documentation.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
APM errata CHIP_21 for the 405EX/EXr (from the rev 1.09 document dated
4/27/11) states that rev D processors may wake up with the wrong feature
set. This patch implements the APM-proposed workaround.
To enable this patch for your board, add the appropriate define for your
CPU to your board header file. See kilauea.h for more information. The
following variants are supported:
#define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY
Please note that if you select the wrong define, your board will not
boot, and JTAG will be required to recover.
Tested on custom boards using:
CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY <sfalco@harris.com>
CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY <eibach@gdsys.de>
Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Though the OpenRD-Base only has one gigabit Ethernet port,
both the OpenRD-Client and OpenRD-Ultimate each have two.
On the Ultimate, the PHY addresses are consecutive, but
on the Client they are not.
(based on
<62a0952ce368acc725063a00a5ec680a639d6c27.1301040318.git.julian.pidancet@citrix.com>
<ad0a2dc1e422698b005d6f0ceb6dd6f75a87e00a.1301040318.git.julian.pidancet@citrix.com>
)
Signed-off-by: Clint Adams <clint@debian.org>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Julian Pidancet <julian.pidancet@citrix.com>
The asm/arch/config.h header define CONFIG_NR_DRAM_BANKS_MAX, which is
needed to configure DRAM banks.
This patch move the asm/arch/config.h header inclusion above the DRAM
banks configuration.
Additionally this patch fix a typo.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
The initial_boot_bank can be set when more than one application is
used in a bootpackage. But a value n <> 0 never led to booting from
bank n. Instead, bank 0 was booted. This patch fixes this.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
commit 91a3c14c (ppc, mgcoge: add DIP switch detection)
introduces an compile error due to an missing define in the
mgcoge2ne.h. DIP switch detection is valid for both boards.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Heiko Schocher <hs@denx.de>
On mgcoge3ne a new environment variable bobcatreset is used.
So this patch adds a possibility to add board specific
environment variables in general and this specific variable
for mgcoge3ne.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reserved bit was changed according to the processors manual.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch adds support for the MPC8247 based board mgcoge3ne.
Additionaly mgcoge2ne board supprot was removed, because due
to the mgcoge3ne, this board is obsolete and not longer
maintained.
The board is similar to mgcoge. The difference is that
a NUMONYX flash is used and a different SDRAM (256MB).
Also introduce CONFIG_KM_82XX to collect ppc82xx common
settings and remove staticness from the common set_pin function.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
Introduce a struct for the BFTICU FPGA to increase the readability of
the code. And the define CONFIG_SYS_BFTICU_BASE was removed because
the CONFIG_SYS_FPGA_BASE is already the base value for BFTICU registers.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
The changes introduced by commit 0abddf8 ``cmd_ide: enhance new
feature "CONFIG_IDE_AHB"'' caused compiler warnings like
cmd_ide.c: In function 'ide_init':
cmd_ide.c:716: warning: assignment from incompatible pointer type
Constify the respective function arguments to fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Although most IDE controller is designed to be connected to PCI bridge,
there are still some IDE controller support AHB interface for SoC design.
The driver implementation of these IDE-AHB controllers differ from other
IDE-PCI controller, some additional registers and commands access is required
during CMD/DATA I/O. Hence a configuration "CONFIG_IDE_AHB" in cmd_ide.c is
required to be defined to support these kinds of SoC controllers. Such as
Faraday's FTIDE020 series and Global Unichip's UINF-0301.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
