This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Through adding CONFIG_QIXIS_I2C_ACCESS macro,
QIXIS_READ(reg)/QIXIS_WRITE(reg, value) can be used
for both i2c and ifc access to QIXIS FPGA. This is
more convenient for coding.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When resuming from deep sleep, the I2C channel may not be
in the default channel. So, switch to the default channel
before accessing DDR SPD.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alt board has been connected to eMMC of 8GB to MMC port.
This enables MMC port and MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lager board has been connected to eMMC of 8GB to MMC1 port.
This enables MMC1 port and MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
stv0991 architecture support added. It contains the support for
following blocks
- Timer
- uart
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Add arch/arm/cpu/armv7/Makefile hunk]
Signed-off-by: Tom Rini <trini@ti.com>
This board sprinkles #ifdef(CONFIG_HERMES) over various global files
such as include/common.h, common/board_r.c, common/cmd_bdinfo.c.
Let's zap such an ill-behaved board.
It has not been converted to generic board yet and mpc8xx is old
enough.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
The U-Boot port runs on a variety of RPi models, not just the B. So,
rename the port to something slightly more generic.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Detect the board revision early during boot, and print the decoded
model name.
Eventually, this information can be used for tasks such as:
- Allowing/preventing USB device mode; some models have a USB device on-
board so only host mode makes sense. Others connect the SoC directly
to the USB connector, so device-mode might make sense.
- The on-board USB hub/Ethernet requires different GPIOs to enable it,
although luckily the default appears to be fine so far.
- The compute module contains an on-board eMMC device, so we could store
the environment there. Other models use an SD card and so don't support
saving the environment (unless we store it in a file on the FAT boot
partition...)
Set $fdtfile based on this information. At present, the mainline Linux
kernel doesn't contain a separate DTB for most models, but I hope that
will change soon.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Set the PHY skew settings for the ethernet phy on the SOCFPGA Cyclone5
hardware.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
BRDCFG1_EMI1_SEL_MASK has been changed to 0x78, which contains
selection bits and connected status bit. So the Corresponding mux
value of RGMII is changed to BRDCFG1_EMI1_SEL_RGMII | BRDCFG1_EMI1_EN.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The new device trees use a more generic interface for
supporting muxing mdio buses. The mux property is thus
specified in "reg", rather than "fsl,hydra-mdio-muxval".
In order to support using old device trees, we keep the
old fixup in there. Linux will therefore see the both
properties, but will ignore fsl,hydra-mdio-muxval.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increase IO drive strength to fix FCS error on RGMII ports
on T1024QDS.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add multiplexing support among SPI flash, TDM riser card and SDXC.
it routes SPI pins to SPI flash by default.
Route SPI pins to SD slot if "adaptor=sdxc" is set in hwconfig.
Route SPI pins to TDM riser card and do fixup for dts if "pin_mux=tdm"
is set in hwconfig.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 v1.1 requires different MEM_PLL_RAT from previous v1.0,
and also update core frequency to 1.8GHz for v1.1.
We reserve the support for T2080 v1.0 and enable v1.1 by default.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card
slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This
Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified
string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp
respectively in hwconfig.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.
A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes2 lanes EFGH either go to SFP or AMC riser card slot2.
By default AMC will be configured even if no hwconfig is specified.
To enable XFI via SFP use the below hwconfig:
fsl_b4860_serdes2:sfp_amc=sfp
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@ffeescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since xfi has no phy, we delete the property "phy-handle" and use
a "fixed-link" property for a xfi port.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We need following changes to make xfi work on B4:
1. set cross-point switch VSC3308 to use sfp config when running xfi;
2. add 10G interface check for xfi;
3. set phy address for xfi so the 10G ports can be registered by mdio;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add the support of newly added LC VCO SerDes protocols
for configuration of IDT and VSC crossbar
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4860, B4440, B4420 and B4220 have MAPLE, so enable law creation
for them only. Remove static LAW creation for MAPLE.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
cppcheck reports:
[board/muas3001/muas3001.c:270]: (error) Uninitialized variable: psize
remove the CONFIG_SYS_RAMBOOT define to prevent this error report.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
This define is never set in our setup, so we can remove it safely. The
former code causes cppcheck to complain about:
[board/keymile/km82xx/km82xx.c:311]: (error) Uninitialized variable:
psize
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Workaround of Errata A-008044 was implemented without errata number and it is
enabled by default. Errata A-008044 is only valid for T1040 Rev 1.0.
So put errata number and make it conditional.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.
Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Adjust timing for dual-rank UDIMM, verified on M3CQ-8GHS3C0E for speed of
1066, 1333, 1600, 1866MT/s. The 1866 timing is copied to 2133 timing in
case such DIMM comes available.
Also update single-rank 1866 timing. Enable interactive debugging as well.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
add FIT support and set "boardid" from factoryset records
"DEV/id" and "COMP/ver". "boardid" is used for selecting
which fit configuration gets booted on the board.
Signed-off-by: Heiko Schocher <hs@denx.de>
a record could contain other records, so after an ">" (begin mark)
there not always come an end mark "<", instead a ">" is possible.
Take care of this.
Signed-off-by: Heiko Schocher <hs@denx.de>
The comments on the QSPI pad assignments erronously swapped
the qspi1_d0 and qspi1_d1 functionality and could cause
confusion. QSPI1_D[0] is in fact muxed on pad U1 (gpmc_a16),
and QSPI1_D[1] - on pad P3 (gpmc_a17). Fixing comments.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Boards using the TWL4030 regulator may not all use the LDOs the same way
(e.g. MMC2 power can be controlled by another LDO than VMMC2).
This delegates TWL4030 MMC power initializations to board-specific functions,
that may still call twl4030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Fix omap3_evm warning, add twl4030.h]
Signed-off-by: Tom Rini <trini@ti.com>
The arch_preboot_os function used in boards using R-Car ARM SoC (r8a7790,
r8a7791, r8a7793 and r8a7794) is common.
This makes rcar-gen2-common/common.c file providing common function for
R-Car ARM SoC, and moves this function to this file.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Control macro of mstp is common in R-Car ARM SoC (r8a7790, r8a7791,
r8a7793 and r8a7794). This moves these to arch-rmobile/rcar-mstp.h
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Module control registers of R-Car ARM SoC (r8a7790, r8a7791, r8a7793 and
r8a7794) are same address. This moves these to header file of SoC.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
BeagleBoard-X15 is the next generation Open Source
Hardware BeagleBoard based on TI's AM5728 SoC
featuring dual core 1.5GHZ A15 processor. The
platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60),
separate LCD port, video In port, 4GB eMMC, uSD,
Analog audio in/out, dual 1G Ethernet.
For more information, refer to:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Out of all OMAP5-like boards, only one of them
needs CONFIG_MISC_INIT_R, so it's best to enable
that for that particular board only, instead of
enabling for all boards unconditionally.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
As checkpatch complaines about these camel-case defines, lets change
them to only use upper-case characters.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
This function is not needed. Remove it to improve the generic init sequence
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Old kernels cannot handle booting in non-secure (hyp) mode, so when
OLD_SUNXI_KERNEL_COMPAT is set, also set ARMV7_BOOT_SEC_DEFAULT.
Note that whether to booting secure or non-secure can always be overriden
using the bootm_boot_mode environment variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
If the target power is connected through a gpio, then give the target some
time to power up before continuing with ahci / sata probing, this avoids
link timeouts, without penalizing other boards where there is no target
power gpio.
Why 500 ms ? I started with 200, that was not enough, then I went to 500 which
worked, lowering it to 350 broke things again, so 500 seems the minimum my
vertex2 needs to be ready to get probed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add simplefb support, note this depends on the kernel having support for
the clocks property which has recently been added to the simplefb devicetree
binding.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as
disussed on the devicetree list]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>.
This adds a fixed mode hdmi driver for the sunxi platform. The fixed
mode is a relatively safe 1024x768, more complete EDID handling is
currently not provided. Only HDMI is supported today.
This code is enabled when HPD detects an attached monitor.
Current config is such that 8MB is shaved off at the top of the RAM.
This avoids several memory handling issues, most significant is the fact
that on linux on ARM you are not allowed to remap known RAM as IO. A
clued in display driver will be able to recycle this reserved RAM in
future though.
cfbconsole was chosen as it provides the most important functionality: a
working u-boot console, allowing for the debugging of certain issues
without the need for a UART.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Major cleanups and some small bugfixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
EC1 pins in RCW can be selected as RGMII1, GPIO3, CAN1/2, FTM1 or
SAI1/2. There is a bug that EC3 RGMII could not work when selecting EC1
as other functionality except RGMII. The workaround is to select
ge2_clk125 for eTSEC clock muxing in register SCFG_ETSECCMCR.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SystemID information could be read through I2C1 from EEPROM
on LS1021ATWR board.
As LS1 is a little-endian processor, getting the version ID by
be32_to_cpu() is wrong. Fix it by using e.version directly.
This change will be compatible for both ARM and PowerPC.
As there is an errata that I2C1 could not work in SD boot,
reading EEPROM through I2C1 is disabled too in SD boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SCFG_SCFGREVCR is SCFG bit reverse register. This register
must be written with 0xFFFFFFFF before writing to any other
SCFG register. Then other SCFG register could be written in
big-endian mode.
Address: 157_0000h base + 200h offset = 157_0200h
Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
W/R SCFGREV
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0-31
SCFGREV SCFG Bit Reverse Control Filed
32'h 0000_0000 - No bit reverse is applied
32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as
0:31
This patch removes the bit reversing for SCFG registers in
u-boot. It will be implemented through PBI commands in RCW
.pbi
write 0x570200, 0xffffffff
.end
So other SCFG register could be written in big-endian mode
in u-boot or kernel directly.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Disable the snoop for slave interface 0, 1 and 2
to avoid the interleaving on the CCI400 BUS.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Eric Benard <eric@eukrea.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Provide board specific implementation for sata stop command for
cm_fx6.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
gw_ventana can boot from SPI or NAND and both of these interfaces boot from
the same 0x400 offset.
This means that we could simplify the code and replace the custom gw_ventana.cfg
with the generic spl_sd.cfg, as it provides the same boot offset of 0x400.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add arch/arm/cpu/armv7/Kconfig with non-secure and virt options, this is a
preparation patch for adding an env variable to choose between secure /
non-secure boot on non-secure boot capable systems, specifically this
prepares for adding CONFIG_ARMV7_BOOT_SEC_DEFAULT as a proper Kconfig option.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
To indicate that U-Boot is active, turn on the blue LED.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The USB host code was missing gpio_request() calls before using the gpio
functions, causing errors to be printed out.
As a side note calls to max77686_set_buck_mode(OPMODE_OFF/OPMODE_ON) have
been removed, as they did not have any effect. This is as per Przemyslaw:
I looked into the documentation and there is a "ENB8" pin in PMIC package.
This pin allows steering BUCK8 ON/OFF by the hardware. If ENB8 is set to low
then you can do on/off. If high, then you cannot change its state by I2C
write, which seems to be the case with the Odroids.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The sandbox/ext4/fat/generic fs commands do not gracefully deal with files
greater than 2GB. Negative values are returned in such cases.
To handle this, the fs functions have been modified to take an additional
parameter of type "* loff_t" which is then populated. The return value
of the fs functions are used only for error conditions.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update board/gdsys/p1022/controlcenterd-id.c,
drivers/fpga/zynqpl.c for changes]
Signed-off-by: Tom Rini <trini@ti.com>
Change the internal FAT functions to use loff_t for offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Fix fs/fat/fat.c for min3 updates]
Signed-off-by: Tom Rini <trini@ti.com>
Some CPUs of some architectures have SOC directories.
At present, the build system directly descends into SOC directories
from the top Makefile, but it should generally descend into each
directory from its parent directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
bcm911360_entphn
bcm911360_entphn-ns
bcm911360k
bcm958300k-ns
bcm958305k
- updates to support Cygnus and NSP board families better
- add functions so CONFIG_ARMV7_NONSEC can be enabled on Cygnus boards
Signed-off-by: Steve Rae <srae@broadcom.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Based on similar patches by Fabio Estevam for mx6sabresd, mx53loco, wandboard
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Add platform data for the GPIO driver. It doesn't need to contain anything
since the GPIO driver will actually use information from the CONFIGs for
now. This merely serves to ensure that the GPIO driver is bound.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert this at91sam9260-based board to use driver model. This should serve
as an example for other similar boards. Serial and GPIO are supported so
far.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Rename this vendor since it is intended to be used on any platform where
coreboot runs at reset and then loads U-Boot.
So far it is only tested on link. When other boards are supported it is
likely that we will need to move to multiple board names, all under the
'coreboot' vendor. So while it would be possible to remove the vendor for
now, that would be short-sighted.
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for CAR so that we have memory to use prior to DRAM init.
On link there is a total of 128KB of CAR available, although some is
used for the memory reference code.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 it is common to use 'post codes' which are 8-bit hex values emitted
from the code and visible to the user. Traditionally two 7-segment displays
were made available on the motherboard to show the last post code that was
emitted. This allows diagnosis of a boot problem since it is possible to
see where the code got to before it died.
On modern hardware these codes are not normally visible. On Chromebooks
they are displayed by the Embedded Controller (EC), so it is useful to emit
them. We must enable this feature for the EC to see the codes, so add an
option for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This board is a 'bare' version of the existing 'link 'board. It does not
require coreboot to run, but is intended to start directly from the reset
vector.
This initial commit has place holders for a wide range of features. These
will be added in follow-on patches and series. So far it cannot be booted
as there is no ROM image produced, but it does build without errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use these new functions where possible. They default to a value of 2 so we
cannot use them in some places where we need a default value of 1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.
Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.
Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Modify the pfuze init for mx6sxsabresd to use the shared
"pfuze_common_init" function. And move this initialization to
power_init_board.
Signed-off-by: Ye.Li <B37916@freescale.com>
Modify the pfuze init for mx6sabresd to use the shared
"pfuze_common_init" function. And move this initialization to
power_init_board.
Signed-off-by: Ye.Li <B37916@freescale.com>
Since the Pfuze initializations are similar on various mx6 SABRE
boards. Factorize the initialization to a common function in file
board/freescale/common/pfuze.c. So that all SABRE boards BSP can
share the function.
Signed-off-by: Ye.Li <B37916@freescale.com>
Add full support for USDHC2, USDHC3, USDHC4 on mx6sx sabresd board.
The default boot socket is USDHC4, so the MMC environment device and
mmcdev variable are set to this device.
Signed-off-by: Ye.Li <B37916@freescale.com>
In U-boot it is preferred to access the register via structure pointer, so
convert it such style.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Let's add mx6sabresd_spl_defconfig entry into MAINTAINERS, so that we avoid
getting a warning that the mx6sabresd_spl is not maintained.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We can simply the return the value from enable_fec_anatop_clock() to make the
code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
We can simply the return the value from enable_fec_anatop_clock() to make the
code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6sabreauto boards come with 32 MiB of parallel NOR flash.
Add support for it:
U-Boot 2015.01-rc1-18107-g1543636-dirty (Nov 14 2014 - 11:11:04)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
Flash: 32 MiB
NAND: 0 MiB
Due to pin conflict with I2C3, only define configure I2C3 IOMUX when flash is
not used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Many boards use a minimal .cfg file in the SPL case.
Introduce spl_sd.cfg so that we can reuse it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR.
Move the configuration to the spl code.
CCM_CCOSR setting is no longer required to get audio functionality in the
kernel, so remove such setting.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR.
Move the configuration to the spl code.
CCM_CCOSR setting is no longer required to get audio functionality in the
kernel, so remove such setting.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6sabresd_spl.cfg configures CCM registers, GPR registers and CCM_CCOSR.
Move the configuration to the spl code.
CCM_CCOSR setting is no longer required to get audio functionality in the
kernel, so remove such setting.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The PFUZ probe failed with the following msg:
" wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=0
wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=1
wait_for_sr_state: failed sr=81 cr=a0 state=2020
i2c_init_transfer: failed for chip 0x8 retry=2
i2c_init_transfer: give up i2c_regs=021a0000
Can't find PMIC:PFUZE100 "
board_early_init_f is too early to call i2c related setting, because
init_func_i2c is called after board_early_init_f being invoked. Thus
move setup_i2c into board_init.
Also PFUZ is connected to I2C bus 0, so change "1" -> "0".
Using this patch PFUZ can be correctly probed:
"PMIC: PFUZE100 ID=0x11"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
1000BASE-KX(1G-KX) uses SGMII protocol but the serdes lane runs in 1G-KX
mode. By default, the lane runs in SGMII mode, when a MAC uses a lane
in 1G-KX mode, corresponding bit in PCCR1 for the lane needs to be set,
and needs to fixup dtb accordingly for kernel to do proper initialization.
Hwconfig "fsl_1gkx" is used to indicate a MAC runs in 1G-KX mode, FM1 MAC
1/2/5/6/9/10 are available for 1G-KX, MAC 3/4 run in RGMII mode. To set a
MAC runs in 1G-KX mode, set its' corresponding env in "fsl_1gkx",
'fm1_1g1' stands for FM1-MAC1, 'fm1_1g2' stands for FM1-MAC2, etc.
If all MAC 1/2/5/6/9/10 run in 1G-KX mode, the hwconfig should has below
setting:
fsl_1gkx:fm1_1g1,fm1_1g2,fm1_1g5,fm1_1g6,fm1_1g9,fm1_1g10
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: Fix compiling warning]
Reviewed-by: York Sun <yorksun@freescale.com>
XFI ports on t2080qds can work with fiber cable and direct attach
cable(copper). We use hwconfig to define cable type for XFI, and fixup
dtb based on the cable type.
For copper cable, set below env in hwconfig:
fsl_10gkr_copper:<10g_mac_name>
the <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4.
fm1_10g1 stands for FM1-MAC9, fm1_10g2 stands for FM1-MAC10, fm1_10g3
stands for FM1-MAC1, fm1_10g4 stands for FM1-MAC2. The four
<10g_mac_name>s do not have to be coexist in hwconfig. For XFI ports, if
a given 10G port will use the copper cable for 10GBASE-KR, set the
<10g_mac_name> of the port in hwconfig, otherwise, fiber cable will be
assumed to be used for the port.
For ex. if four XFI ports will both use copper cable, the hwconfig
should contain:
fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The gdsys hrcon board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x GbE (optional)
- Lattice ECP3 FPGA connected via eLBC and PCIe
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk found this issue using cppcheck:
(error) Uninitialized variable: fpga_features
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display (optional, disabled by default)
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The code for this board supports following features:
- Boot media support: NAND flash/SD card/SPI flash
- Support LCD display
- Support ethernet
- Support USB mass storage
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
replaces the at91bootstrap code with SPL code.
make the spl image with:
./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin
this writes the length of the spl image into the 6th
execption vector. This is needed from the ROM bootloader.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This change adds support for enabling the USB host features of the board.
This includes the USB3503A hub and the SMC LAN9730 ethernet controller
as well.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This adds following things :
- New config and defconfig for Peach-Pi board.
- Alterations in Kconfig and MAINTAINERS.
- Addition of CONFIG_EXYNOS5800.
- ADdition of exynos5800-peach-pi in dts list.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Gose board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lager board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Koesch board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Alt board is defined CONFIG_SYS_SDRAM_BASE, and this can use a basic function of
dram_init_banksize instead.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode
There are two usb port on mx6sxsabresd board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to make host port work in HOST mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
Add pinmux settings, implement board_ehci_hcd_init, board_usb_phy_mode
There are two usb port on mx6slevk board:
1. otg port
2. host port
The following are the connection between usb controller and board usb
interface, host port has not ID pin set:
otg1 core <---> board otg port
otg2 core <---> board host port
In order to make host port work, board_usb_phy_mode return USB_INIT_HOST
to let host port work in host mode.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
* fdt_fixup_mtdparts is called from ft_board_setup
* Run "mtdparts default" to create NAND partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
* fdt_fixup_mtdparts is called from ft_board_setup
* run "mtdparts default" to create NAND, NOR partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
-A_007662 states that for x1 link width, PCIe2 controller trains in
Gen1 speed while configured for Gen2 speed.
Workaround:Set the width to x1 and speed to Gen2 by writing to
CCSR registers in PBI phase
-A_008007 states that PVR register may show random value.
Workaround: Reset PVR register using DCSR space in PBI phase
Add PBI based software workaround for A_007662 and A_008007
in t104x_pbi.cfg. This is required for SPL-based bootloaders
like NAND-boot, SD-boot, SPI-boot
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This support of CPLD includes
- Files and register definitions
- Command to switch alternate bank
- Command to switch default bank
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add initial support for TBS2910 Matrix ARM miniPC.
Support includes MMC, Ethernet, UARTs, HDMI, USB, SATA, PCI, I2C, RTC.
Signed-off-by: Soeren Moch <smoch@web.de>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch will enable the support for SPL on iMX6 SabreSD.
It tested on SD2 and SD3 mmc port (Switch 1 or 2 of SW6)
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The i.MX6Q/DL sabreauto board has one NAND socket, set the
CONFIG_NAND_MXS and relevant NAND configurations to enable the
MXS NAND flash driver.
Add board level codes to set IOMUX and clock for GPMI-NAND and
BCH module.
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Today I got the final board and found out that a different
connector is used as the one on my development board. The
new connector has swaped pins for cd and wp.
This change is tested on a production ready board.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Since kernel 3.15 there are two dtb's for the imx53-qsb board:
imx53-qsb.dtb - For the boards with DA9053 PMIC
imx53-qsrb.dtb - For the boards with MC34708 PMIC
Change the 'fdt_file' dynamically, so that the correct dtb can be used depending
on the board variant.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
The magic bit toucher needs to be updated to reflect the new board Kconfig structure
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for the 2 ehci controllers found on the sun6i (A31) soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Marek Vasut <marex@denx.de>
Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to
Kconfig being the right thing to do, an added advantage of this is that it
allows for boards without Vbus gpio-s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Enable the SPL now that we've all the necessary bits in place.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31 uses the AXP221 pmic for various voltages.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
--
Changes in v2:
-Rebase
Changes in v3:
-Add support for all dldo and aldo-s
-Add Kconfig option to select building AXP221 and to select voltage of
dldo and aldo-s
Changes in v4:
-Add axp221_setbits helper function
-Use symbolic names for enabled bits in CTRL1 - CTRL3 registers
This commit adds "select CPU_V7" for some new boards that were not
covered by commit 2e07c249a6
(kconfig: arm: introduce symbol for ARM CPUs).
Redundant "SYS_CPU" defines and "string" directives should be removed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Georges Savoundararadj <savoundg@gmail.com>
Now each board selects one of CONFIG_CPU_SH2, CONFIG_CPU_SH3,
CONFIG_CPU_SH4, so let's move CONFIG_SYS_CPU definition to
arch/sh/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
mcc200 and prs200 are old and have no maintainer. Remove the boards.
This also removes the mcc200 specific 1bpp BMP support from
common/lcd.c
Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
The latest Xilinx tools generate ps7_init files that are explicitly
available under GPL. Change the makefile to allow drop in of those files
for building the SPL.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-and-tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
cppcheck reports:
[board/esd/common/auto_update.c:458]: (error) Uninitialized variable: cnt
The variable is not really used anywhere, so remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
The i2c_init function is no longer necessary.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Alt board was connected Power IC to channel 1 of sh-i2c. Source code that
controls this is already included, but channel 1 of sh-i2c is not enabled.
This enables channel 1 of sh-i2c, and can use.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Alt board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lager board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Koelsch board does not use board_late_init function.
This removes this function and define of BOARD_LATE_INIT from config.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Gose board has one ether port, this works using sh-ether driver.
This adds GPIO settings and driver settings in order to use the sh-ether.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix error detected by cppcheck:
[board/renesas/ecovec/ecovec.c:66]: (error) Buffer is accessed out of
bounds.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix error detected by cppcheck:
[board/matrix_vision/mvblx/sys_eeprom.c:353]: (error) Buffer is
accessed out of bounds.
Signed-off-by: Wolfgang Denk <wd@denx.de>
cc: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Michael Jones <michael.jones@matrix-vision.de>
Fix error detected by cppcheck:
[board/cogent/lcd.c:237]: (error) Invalid number of character (()
when these macros are defined:
'CONFIG_SHOW_ACTIVITY;CONFIG_STATUS_LED'.
Signed-off-by: Wolfgang Denk <wd@denx.de>
There are a number of places where U-Boot intentionally and legally
accesses physical address 0x0000, for example when installing
exception vectors on systems where these are located in low memory.
Add "cppcheck-suppress nullPointer" comments to silence cppcheck
where this is intentional and legal.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add example of an USB UDC configuration with DFU and UMS.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Add both host and mUSB support.
Currently, the selection between host USB and mUSB is done through the
config file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
CompuLab cm-t3517 is Computer on Module (CoM) based on AM3517 SoC.
Features: up to 256MB DDR2, up to 512MB NAND, USB hub, mUSB, WiFi, BT,
Analog audio codec, touch screen controller, LED.
Add basic support including:
LED, Serial console, NAND, MMC, GPIO, I2C, 256MB DRAM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Switch the default CD GPIO polarity to active low.
The current hsmmc driver assumption that the CD GPIO is active high, but
in the real hardware, usually the opposite holds.
The usual SD card socket has a mechanical switch which is grounded as
soon as a card is inserted.
Of course there might be some board logic which inverts the signal, but
as far as current users are concerned, there is no such logic.
Current U-Boot users either not using the CD functionality, or have a
different way (e.g. external to SoC GPIO controller) for checking the
card presence.
This patch also brings the polarity assumption in line with the Linux
kernel and adds appropriate comments.
This patch also might spare issues once the TWL GPIO driver will be
converted to the DM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
The fallback is used for cases when CONFIG_SERIAL_TAG defined, but the
eeprom is not used.
The fallback is useful for more than one CompuLab board, so move it to a
common location.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
