There two iomuxc for i.MX6ULL. one iomuxc is compatible is i.MX6UL,
the other iomuxc is for SVNS usage, similar with the one in mx7.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
i.MX6ULL has two 128 bits fuse banks, bank 7 and bank 8,
while other banks use 256 bits. So we have to adjust the
word and bank index when accessing the bank 8.
When in command line `fuse read 8 0 1`, you can image
`fuse read 7 4 1` in the ocotp driver implementation for 6ULL.
When programming, we use word index, so need to fix bank7/8 programming
for i.mx6ull.
For example: fuse prog 8 3 1; The word index is (8 << 3 | 3) --> 67.
But actully it should be (7 << 3 | 7) ---> 63.
So fix it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Currently the driver asserts WDOG_B by clearing WCR_WDA bit when
enabling the watchdog. Do not clear WCR_WDA.
Signed-off-by: Ross Parker <rossjparker@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
add driver support for pwm regulator.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
when using tftp on the smartweb board, it prints a lot of
CACHE: Misaligned operation at range [23b2e000, 23b2e100]
warnings ... fixed them.
Signed-off-by: Heiko Schocher <hs@denx.de>
Creating multiple entries of "config FOO" often gives us bad
experiences. In this case, we should specify "default X86"
as platforms that want this keyboard by default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently the controller by default enables the Receive Detect feature in P3
mode in USB 3.0 PHY. However, USB 3.0 PHY does not reliably support receive
detection in P3 mode.
Enabling the USB3 controller to configure USB in P2 mode whenever the Receive
Detect feature is required.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
The functions fdt_fixup_erratum and fdt_fixup_usb_erratum are
fsl/nxp specific. So, make them explicit by renaming them
fsl_fdt_fixup_erratum and fsl_fdt_fixup_usb_erratum
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
The function fdt_fixup_dr_usb is specific to fsl/nxp. So,
make the function name explicit and rename fdt_fixup_dr_usb
into fsl_fdt_fixup_dr_usb.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
This is required for better performance, and performs below tuning:
1. Enable burst length set, and define it as 4/8/16.
2. Set burst request limit to 16 requests.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Commit 147271209a ("net: asix: fix operation without eeprom")
added a special handling for ASIX 88772B that enable another
type of header. This break the driver in DM mode as the extra handling
needed in the receive path is missing.
However this new header mode is not required and only seems to
increase the code complexity, so this patch revert this part of
commit 147271209a.
This also reverts commit 41d1258ace
("net: asix: Fix AX88772B when used with DriverModel") of late.
Fixes: 147271209a ("net: asix: fix operation without eeprom")
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
USB ULPI PHY reset signals are typically active low. Consequently, they
should be marked as GPIO_ACTIVE_LOW in device tree, and indeed they are in
the Linux kernel DTs, and in DT properties that U-Boot doesn't yet use.
However, in DT properties that U-Boot does use, the value has been set to
0 (== GPIO_ACTIVE_HIGH) to work around a bug in U-Boot.
This change fixes the DT to correctly represent the HW, and fixes the
Tegra USB driver to cope with the fact that dm_gpio_set_value() internally
handles any inversions implied by the DT value GPIO_ACTIVE_LOW.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now that the standard clock/reset APIs are available for all Tegra SoCs,
convert the I2C driver to use them exclusively, and remove any references
to the custom Tegra-specific APIs.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now that the standard clock/reset APIs are available for all Tegra SoCs,
convert the MMC driver to use them exclusively, and remove any references
to the custom Tegra-specific APIs.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Implement a clock uclass driver for the Tegra CAR. This allows clients to
use standard clock APIs on Tegra. This device is intended to be
instantiated by the core Tegra CAR driver, rather than being instantiated
directly from DT. The implementation uses the existing custom Tegra-
specific clock APIs to avoid coupling the series with significant
refactoring of the existing Tegra clock/clock code. The driver currently
only supports peripheral clocks, and avoids support for other clocks such
as PLLs and external clocks. This should be sufficient to convert over all
Tegra peripheral drivers, and avoids a complex implementation which calls
different Tegra-specific clock APIs based on the type of clock being
manipulated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Implement a reset uclass driver for the Tegra CAR. This allows clients to
use standard reset APIs on Tegra. This device is intended to be
instantiated by the core Tegra CAR driver, rather than being instantiated
directly from DT. The implementation uses the existing custom Tegra-
specific reset APIs to avoid coupling the series with significant
refactoring of the existing Tegra clock/reset code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra CAR (Clock And Reset) module provides control of most clocks
and reset signals within the Tegra SoC. This change implements a driver
for this module. However, since the module implements multiple kinds of
services (clocks, resets, perhaps more), all this driver does is bind
various sub-devices, which in turn provide the real services. This driver
is essentially an "MFD" (Multi-Function Device) in Linux kernel speak.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Convert the Tegra MMC driver to DM_MMC. Support for non-DM is removed
to avoid ifdefs in the code. DM_MMC is now enabled for all Tegra builds.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
(swarren, fixed some NULL pointer dereferences, removed extraneous
changes, rebased on various other changes, removed non-DM support etc.)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
struct mmc_host is a Tegra-specific structure, but the name implies it's
something defined by core MMC code, which is confusing. Rename it to
struct tegra_mmc_priv to make its purpose more obvious. The new name is
also more appropriate for a DM driver private data structure, which will
be relevant later in this series.
Nothing needs access to this type except the MMC driver itself. Move the
definition into the driver C file.
Make sure all Tegra MMC functions are named tegra_mmc_*. Even though
they're all static, it's useful to have good naming so that symbol tables
are easy to interpret. A few functions aren't renamed by this patch since
they'll be deleted by a subsequent patch in this series.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The MMC driver will soon be converted to use standard clock/reset APIs,
and so the periph_id field in the MMC device priv struct will disappear.
Rework the implementation of pad_init_mmc() to rely on this; using the
device register address is a much more direct test anyway.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
pad_init_mmc() is performing an SoC-specific operation, using registers
within the MMC controller. There's no reason to implement this code
outside the MMC driver, so move it inside the driver.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra MMC driver currently honors "sdhci" entries in /aliases. The
MMC core however uses "mmc" entries in /aliases. This difference will be
relevant once the Tegra MMC driver is converted to DM, and the MMC core
handles alias lookups. To avoid issues during that conversion, fix the
Tegra MMC driver and all Tegra DTs to use the same alias name as the MMC
core does.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
To allow a board- / platform-specific ahci_port_base() function, this
patch removes "static inline" and adds __weak to this function. This
will be used by the upcoming Armada 7K/8K SATA / AHCI support, which
unfortunately needs a different port base address calculation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
To enable this driver on Armada 7K/8K this patch adds the compatibility
property to the list.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This version is based on the Marvell U-Boot version with this patch
applied as latest patch:
Git ID 7f408573: "fix: comphy: cp110: add comphy initialization for usb
device mode" from 2016-07-05.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This version is based on the Marvell U-Boot version with this patch
applied as latest patch:
Git ID 7f408573: "fix: comphy: cp110: add comphy initialization for usb
device mode" from 2016-07-05.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds DM based support for the Armada 3700 EHCI controller.
The address windows don't need to get configured in this case. The
difference here is detected via DT compatible property at runtime.
With this support and the DM xHCI driver, both XHCI and eHCI can be
used simultaniously on the MVEBU boards now.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch adds DM based support for the xHCI USB 3.0 controller
integrated in the Armada 3700 SoC. It may be extended to be used
by other MVEBU SoCs as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch adds support for the Armada 3700 SoC to the Marvell mvneta
network driver.
Not like A380, in Armada3700, there are two layers of decode windows for GBE:
First layer is: GbE Address window that resides inside the GBE unit,
Second layer is: Fabric address window which is located in the NIC400
(South Fabric).
To simplify the address decode configuration for Armada3700, we bypass the
first layer of GBE decode window by setting the first window to 4GB.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The mvneta driver is also used on the ARMv8 64bit Armada 3700 SoC. This
patch fixes the compilation warnings seen on this 64bit platform.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The SPI IP core in the Marvell Armada 3700 is similar to the one in the
other Armada SoCs. But the differences are big enough that it makes
sense to introduce a new driver instead of cluttering the old
kirkwood driver with #ifdef's.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The Armada 3700's UART is a simple serial port. It has a 32 bytes
Tx FIFO and a 64 bytes Rx FIFO integrated. This patch adds support
for this UART including the DEBUG UART functions for very early
debug output.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the warnings:
CACHE: Misaligned operation at range ...
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Introduce a hidden USB_FUNCTION_DFU Kconfig option and select it for
CMD_DFU (as we must have the DFU command enabled to do anything DFU).
Make all of the entries in drivers/dfu/Kconfig depend on CMD_DFU and add
options for all of the back end choices that DFU can make use of.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Previously, DFU was not built in for SPL and often disabled via the board
config.h file, in the SPL build. By moving DFU to Kconfig we now need to
move this logic to the Makefile to continue to allow boards to fit within
their SPL size limit (until gcc 6 is more widespread and unused strings will
be discarded).
Signed-off-by: Tom Rini <trini@konsulko.com>
move the UBI config options into Kconfig.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Reviewed by: Evgeni Dobrev <evgeni at studio-punkt.com>
Instead of using multiple macros, a data structure is used to pass
board-specific parameters to MMDC DDR driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this option to Kconfig and clean up existing uses.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
By adding the "marvell,mv78230-i2c" compatible property, we can enable
this I2C driver to support these new ARM64 chips as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
The I2C bus will get stuck when reading 0 byte. So we add validation of
the read length in i2c_read(). This issue only occurs on read operation.
Signed-off-by: jinghua <jinghua@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
This patch adds runtime speed configuration to the mv_i2c driver.
Currently standard (max 100kHz) and fast mode (max 400kHz) are
supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
To prepare for the DM conversion, we add a layer of compatibility
functions to be used by both the legacy and the DM functions.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
This driver is designed in a generic manner, so resets should be
handled generically as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
We are supposed to use #include <...> to include headers in the
public include paths. We should use #include "..." only for headers
in local directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The remove callbacks of EHCI drivers are often just a wrapper of
ehci_deregister.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
For vidconsole_post_probe(), it is common coding style to let a
probe method return the value of a register function.
The others will become simple wrapper functions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
These functions can be much simpler by squashing lines for immediate
return.
For *_bind() callbacks, they will be a simple wrapper function of an
upper-level bind API.
For mmc_set_{boot_bus_width,part_conf}, they will be a wrapper of
mmc_switch().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
To sync the DT binding with Linux, the register base must be taken
from the parent syscon node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move U_BOOT_DRIVER() entry from the data file (clk-uniphier-mio.c)
to the core support file (clk-uniphier-core.c) because I do not want
to repeat the driver boilerplate when I add more clock data.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
pmucru is a module like cru which is a clock controller manage some PLL
and module clocks.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch add support for rockchip dwc3 controller, which corresponding
to the two type-C port on rk3399 evb.
Only support usb2.0 currently for we have not enable the usb3.0 phy
driver and PD(fusb302) driver.
Signed-off-by: MengDongyang <daniel.meng@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
We consider the grf setting for pwm controller select as the system
operation instead of driver operation, move it to soc init, let's
remove it from pwm driver first.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch use clock API instead of hardcode for get pwm clock.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fix printf() to debug() nit:
Signed-off-by: Simon Glass <sjg@chromium.org>
Since FSL_QSPI driver still supporting non-dm code
better to move the Kconfig from DM undefined place.
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Add PL bitstream dowload support for ZynqMP
Bitstream will be validated by uboot and loaded
to PL by invoking an smc instruction to ATF which route this request to
PMU FW which will take care of loading it to PL
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Current code generates warning when it is compiled for arm64:
Warnings:
In file included from drivers/spi/zynq_spi.c:14:0:
drivers/spi/zynq_spi.c: In function ‘zynq_spi_init_hw’:
drivers/spi/zynq_spi.c:95:9: warning: large integer implicitly truncated
to unsigned type [-Woverflow]
writel(~ZYNQ_SPI_ENR_SPI_EN_MASK, ®s->enr);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro
‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v;
})
^
drivers/spi/zynq_spi.c: In function ‘zynq_spi_release_bus’:
drivers/spi/zynq_spi.c:177:9: warning: large integer implicitly
truncated to unsigned type [-Woverflow]
writel(~ZYNQ_SPI_ENR_SPI_EN_MASK, ®s->enr);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro
‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v;
})
^
This patch is using one variable to do conversion via u32 variable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This patch moves flags macro's to respective member position on
spi_flash_params{}, for better readabilty and finding the
respective member macro's easily.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Add CONFIG_SPI_FLASH_USE_4K_SECTORS in spi_flash code from header file.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
SECT_32K never used anywhere in the code.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Make rx mode flags as generic to spi, earlier mode_rx is
maintained separately because of some flash specific code.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
e_rd_cmd is maintained separately for fastest read command code,
since the read commands are computed normally this e_rd_cmd
is not required in spi_flash_params table.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Fastest read command code look for fastest read command
taking inputs from spi->mode_rx and flags from param table
and controller mode_rx is always been a priority.
Since mode_rx is always set from controller side this optimized
code doesn't require much and this code required exctra overhead like
1) Maintain e_rx_cmd in param table
2) Maintain mode_rx in spi_slave {}
Hence removed this code, and look for read command from normal
spi->mode from spi_slave{} and params->flags
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This udelay() was added as an HACK and is no longer required. All
read/write/erase operations work fine even without this delay. Hence,
remove the udelay() call.
Tested read/write/erase operation on AM437x SK. Also tested QSPI Boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
TI QSPI has four 32 bit data registers which can be used to transfer 16
bytes of data at once. The register group QSPI_SPI_DATA_REG_3,
QSPI_SPI_DATA_REG_2, QSPI_SPI_DATA_REG_1 and QSPI_SPI_DATA_REG is
treated as a single 128-bit word for shifting data in and out. The bit
at QSPI_SPI_DATA_REG_3[31] position is the first bit to be shifted out
in case of 128 bit transfer mode. Therefore the first byte to be written
to flash should be at QSPI_SPI_DATA_REG_3[31-25] position.
Instead of writing 1 byte at a time when interacting with SPI NOR flash,
make use of all the four registers so that 16 bytes can be transferred
in one go.
With this patch, the flash write speed increases from ~250KBs/ to
~650KB/s on DRA74 EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
During spi transfer, for example:
sspi 1:1.0 8 ff
the rx_len values will be:
rx_len = 0
rx_len = 4294967295
This caused a busy looping during xfer, this patch fixes it
by adding a check while reading the rx fifo
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add a simple driver for the clocks provided by the MIPS Boston
development board. The system provides information about 2 clocks whose
rates are fixed by the bitfile flashed in the boards FPGA, and this
driver simply reads the rates of these 2 clocks.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a trivial syscon driver matching the generic "syscon" compatible
string, allowing for simple system controllers to be used without a
custom driver just as in Linux.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Device model drivers have previously been matched to FDT nodes by virtue
of being the first driver in the driver list to be compatible with the
node. This ignores the fact that compatible strings in the device tree
are listed in order of priority - that is, if we have a node with 2
compatible strings & a driver that matches each then we should always
probe the driver that matches the first compatible string.
Fix this by looping through the compatible strings for a node when
attempting to bind it in lists_bind_fdt and checking each driver for
a match of the first string, then each driver for a match of the second
string etc. Effectively this inverts the loops over compatible strings &
drivers.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The regmap_read & regmap_write functions were previously declared in
regmap.h but not implemented anywhere. The regmap implementation &
commit message of 6f98b7504f ("dm: Add support for register maps
(regmap)") indicate that only memory mapped accesses are supported for
now, so providing simple implementations of regmap_read & regmap_write
is trivial. The access size is presumed to be 4 bytes & endianness is
presumed native, which are the defaults for the regmap code in Linux.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pch_gbe driver previously casted pointers to & from unsigned 32 bit
integers in many locations. This breaks the driver on 64 bit systems,
producing streams of compiler warnings about mismatched pointer &
integer sizes and then failing to keep track of addresses correctly at
runtime.
Fix the driver for 64 bit systems by using unsigned longs in place of
the previously used 32 bit integers.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reading the PCI BAR & converting the result to a physical address is not
safe across all architectures. For example on MIPS the virtual:physical
mapping is not 1:1, so we cannot directly make use of the physical
address.
Use the more generic BAR-mapping function dm_pci_map_bar to discover the
MMIO base address, which should work across architectures.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In pci_uclass_pre_probe an attempt is made to detect whether the parent
of a device is a PCI device and that the device is thus a bridge. This
was being done by checking whether the parent of the device is of the
UCLASS_ROOT class. This causes problems if the PCI controller is a child
of some other non-PCI node, for example a simple-bus node.
For example, if the device tree contains something like the following
then pci_uclass_pre_probe would incorrectly believe that the PCI
controller is a bridge, with a PCI parent:
/ {
some_child {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <>;
pci_controller: pci@10000000 {
compatible = "my-pci-controller";
device_type = "pci";
reg = <0x10000000 0x2000000>;
};
};
};
Avoid this incorrect detection of bridges by instead checking whether
the parent devices class is UCLASS_PCI and treating a device as a bridge
when this is true, making use of device_is_on_pci_bus to perform this
test.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a driver for the Xilinx AXI bridge for PCI express, an
IP block which can be used on some generations of Xilinx FPGAs. This is
mostly a case of implementing PCIe ECAM specification, but with some
quirks about what devices are valid to access.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Previously ns16550 compatible UARTs probed via device tree have needed
their device tree nodes to contain a clock-frequency property. An
alternative to this commonly used with Linux is to reference a clock via
a phandle. This patch allows U-Boot to support that, retrieving the
clock frequency by probing the appropriate clock device.
For example, a system might choose to provide the UART base clock as a
reference to a clock common to multiple devices:
sys_clk: clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <10000000>;
};
uart0: uart@10000000 {
compatible = "ns16550a";
reg = <0x10000000 0x1000>;
clocks = <&sys_clk>;
};
uart1: uart@10000000 {
compatible = "ns16550a";
reg = <0x10001000 0x1000>;
clocks = <&sys_clk>;
};
This removes the need for the frequency information to be duplicated in
multiple nodes and allows the device tree to be more descriptive of the
system.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
out_be32 and in_be32 are actually #defined to little endian
writel/readl in arch/microblaze.
Just use __raw_writel/readl instead. That is also what is used
in the Linux kernel driver for this IP block
Tested on MIPSfpga. Can tftp a kernel.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Virtual to physical mapping isn't necessarily 1:1 for all architectures
Using ioremap_nocache allows for the arch code to translate the
physical address to a virtual address.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When DTO interrupt occurred, there are any remaining data still in FIFO
due to RX FIFO threshold is larger than remaining data. It also
causes that dwmmc didn't trigger RXDR interrupt, so is TX.
It's responsibility of driver to read remaining bytes on seeing DTO
interrupt.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
To SD, there is no erase group, then the value erase_grp_size
will be default 1. When erasing SD blocks, the blocks will be
erased one by one, which is time consuming.
We use AU_SIZE as a group to speed up the erasing.
Erasing 4MB with a SD2.0 Card with AU_SIZE 4MB.
`time mmc erase 0x100000 0x2000`
time: 44.856 seconds (before optimization)
time: 0.335 seconds (after optimization)
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stephen Warren <swarren@nvidia.com>
Add function to read SD_STATUS information.
According to the information, get erase_timeout/erase_size/erase_offset.
Add a structure sd_ssr to include the erase related information.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Stephen Warren <swarren@nvidia.com>
No need for per-SoC adjustment for this parameter. It should be
determined by the slowest hardware. Currently, no board overrides
this CONFIG, so 3.2 sec is large enough. (If not, we can make it
even larger.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This CONFIG is not configurable since it is not guarded by #ifndef.
Nobody has complained about that, so there is no need to keep it as
a CONFIG option.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called. Move this
quirk handling to sdhci_setup_cfg(), which is now the central place
for hardware capability checks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called. Move this
quirk handling to sdhci_setup_cfg(), which is now the central place
for hardware capability checks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
"Hardware doesn't specify base clock frequency" may not be only the
error case of sdhci_setup_cfg(). It is better to print this where
the corresponding error is triggered.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_BLK is enabled, add_sdhci() is never called.
So, sdhci_reset() is not called, either. This is a problem for
my board as it needs the reset to start from a sane state.
Move the add_sdhci() call to sdhci_init(), which is visited
by both of the with/without CONFIG_BLK cases.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On LD4 SoC or later, the pin-mux registers are 8bit wide, while 4bit
wide on sLD3 SoC. Support it for the sLD3 pinctrl driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With sunxi-musb musb_lowlevel_init() can fail when a charger; or no cable
is plugged into the otg port.
To avoid leaking the struct musb allocated by musb_init_controller()
on repeated musb_usb_probe() calls, we were caching its result.
But musb_init_controller() does more, such as calling sunxi_musb_init()
which enables the clocks.
Not calling sunxi_musb_init() causes the musb controller to stop working
after a "usb reset" since that calls musb_usb_remove() which disables the
clocks.
This commit fixes this by removing the caching of the struct returned
from musb_init_controller(), it replaces this by free-ing the allocated
memory in musb_usb_remove() and calling musb_usb_remove() on
musb_usb_probe() errors to ensure proper cleanup.
While at it also make musb_usb_probe() and musb_usb_remove() static.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The Linux kernel musb driver expects VBUS to be off while initializing
musb. Having it on results in a repeating string of warnings, followed
by an unusable peripheral. The peripheral is only usable after
physically removing the OTG adapter, letting musb reset its state.
This partially reverts commit c9f8947e66 ("sunxi: usb-phy: Never
power off the usb ports")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When cold-booting the ldoio0/1 regulators are always off / the
gpios are always at tristate. But when re-booting from android these
are sometimes on. Disable them at axp_init time (iow as early as possible)
to remove this difference between a cold boot and a reboot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
At present TPL uses the same options as SPL support. In a few cases the board
config enables or disables the SPL options depending on whether
CONFIG_TPL_BUILD is defined.
With the move to Kconfig, options are determined for the whole build and
(without a hack like an #undef in a header file) cannot be controlled in this
way.
Create new TPL options for these and update users. This will allow Kconfig
conversion to proceed for these boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
When CONFIG_SYS_FSL_ERRATUM_A009801 is defined but
CONFIG_SYS_FSL_ERRATUM_A008511 not defined, there is compile error
that temp32 undeclared, this patch fixes it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This general MMDC driver adds basic support for Freescale MMDC
(Multi Mode DDR Controller). Currently MMDC is integrated on ARMv8
LS1012A SoC for DDR3L, there will be a update to this driver to
support more flexible configuration if new features (DDR4, multiple
controllers/chip selections, etc) are implimented in future.
Meantime, reuse common MMDC driver for LS1012ARDB/LS1012AQDS/
LS1012AFRDM.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
DDR controller 5.2.1 has this erratum A008511 partially fixed.
The workaround needs to be adjusted to take advantage of Vref
training. This patch enables the training and force output
enable to be off.
Erratum A009803 requires the controller to be idel before enabling
address parity. It was combined with workaround for A008511. With
new A008511 flow, this flow needs to be changed to enabling
data init (D_INIT) after the address parity is enabled.
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
32 more debug registers are added for newer DDR controllers.
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
The current code would always use the speed and mode set by
CONFIG_ENV_SPI_MAX_HZ and CONFIG_ENV_SPI_MODE. But if using
SPI driver model it should get the values from DT.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
These macros are only referenced in pinctrl-uniphier-core.c, so
they need not reside in a header file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is the state-of-the-art MMC driver implementation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver has not been converted to Driver Model, and it is an
obstacle to migrate other block device drivers. Remove it for now.
The UniPhier SoCs already use a DM-based EHCI driver, so now
ARCH_UNIPHIER can select DM_USB.
These two changes must be done atomically because removing the
legacy driver causes a build error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Since the 'clk_client.h' doesn't exist, it should be 'clk.h'.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The special handling of the chip address and register address must only
happen before we send the data buffer, otherwise we will end up
inserting both of these every 32 bytes.
Signed-off-by: John Keeping <john@metanate.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no point in writing intermediate values to the txdata
registers.
Also add padding to the debug logging to make it easier to read when
there are leading zeroes.
Signed-off-by: John Keeping <john@metanate.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make it clear that we are using the same value in two adjacent lines.
Signed-off-by: John Keeping <john@metanate.com>
Acked-by: Simon Glass <sjg@chromium.org>
A previous patch (net: asix: fix operation without eeprom) added a
two-byte shift to the packet buffer when receiving a packet on the
AX88772B.
This shift was not included when the driver was updated to work with
DriverModel. Testing on a Marvell DB-88F6820-ACM showed that the adapter
was not functioning correctly (EHCI timeouts).
This patch brings the two-byte shift to the DriverModel implementation
of ops->recv (asix_eth_recv).
Testing on the same board, we were able to TFTP a file over and confirm
that the crc32 was correct.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When enabling a fixed regulator, it may take some time to rise to the
correct voltage. If we do not delay here then subsequent operations
will fail.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove the device definition from board file, update the driver with
the new compatible property and update config with necessary options.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a pin controller driver for Meson GXBB adapted from Linux kernel.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In cases where the pins and groups definitions are in a sub-node, as:
uart_a {
mux {
groups = "uart_tx_a", "uart_rx_a";
function = "uart_a";
};
};
pinctrl_generic_set_state_subnode() returns an error for the top-level
node and pinctrl_generic_set_state() fails. Instead, return success so
that the child nodes are tried.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
On the raspberry pi, you can disable the serial port to gain dynamic frequency
scaling which can get handy at times.
However, in such a configuration the serial controller gets its rx queue filled
up with zero bytes which then happily get transmitted on to whoever calls
getc() today.
This patch adds detection logic for that case by checking whether the RX pin is
mapped to GPIO15 and disables the mini uart if it is not mapped properly.
That way we can leave the driver enabled in the tree and can determine during
runtime whether serial is usable or not, having a single binary that allows for
uart and non-uart operation.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far we could only tell the gpio framework that a GPIO was mapped as input or
output, not as alternative function.
This patch adds support for determining whether a function is mapped as
alternative.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Currently the command buffer gets allocated with a size of 32 bytes.
This causes warning messages on systems with cache lines bigger than
32 bytes:
CACHE: Misaligned operation at range [9df17a00, 9df17a20]
Define command buffer to be at least 32 bytes, but more if cache
line is bigger.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Now that nand_info[] is an array of pointers we need to test the
pointer itself rather than using name as a proxy for NULLness.
Fixes: b616d9b0a7 ("nand: Embed mtd_info in struct nand_chip")
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
In commit 17cb4b8f32 ("mtd: nand: Add+use mtd_to/from_nand and
nand_get/set_controller_data") the assignment of mtd->priv was removed
but was not replaced. This adds the required nand_set_controller_data()
call.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This is very likely to be necessary for normal use cases.
Set its default to 'y' for shorter defconfig files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With the CONFIG_DM_MMC_OPS migration, the .set_ios callback can
return an integer now. Return an appropriate error value rather
than sudden death by BUG().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
No more reason to define this function above the ops structure.
Move it near the caller. Also, change its return type to void
because it never fails.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Catch up with the DM migration.
As struct dm_mmc_ops does not have .init callback, call the init
function directly from the probe function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When the backlight's pwm input is connected to a pwm output of the SoC,
actually use pwm to drive the backlight.
The mean reason for doing this is to fix the backlight turning off
for aprox. 1 second while the kernel is booting. This is caused by
the kernel actually using pwm to drive the backlight, so that it
can dim the backlight. First the pwm driver loads and switches the
pinmux for the pin driving the backlight's pwm input to the pwm
controller. Then about 1s later the actual backlight driver loads
and tells the pwm driver to actually update the pwm settings, which
have a power-on-reset value of "off".
An additional advantage is that this allows us to initatiate the
backlight at 80%, which is the kernel default, avoiding a brightness
change while the kernel loads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed by: Peter Korsgaard <peter@korsgaard.com>
Patch f8a10ed1 [i2c: mvtwsi: Make address length variable] accidentally
inverted the sequence of address bytes sent to the I2C device. This
patch corrects this by sending the highest byte first and the lowest
byte last again.
Tested on theadorable Armada-XP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Heiko Schocher <hs@denx.de>
In tegra20_slink.c, the set_mode() function may be executed before the
SPI bus is claimed the first time, and hence the clocks to the SPI
controller may not be running. If so, any register read/write at this
time will hang the CPU. Fix this by ensuring the clock is running as soon
as the driver is probed. This is observed on the Tegra30 Beaver board.
Apply the same clock initialization fix to all other Tegra SPI drivers so
that if set_mode() is ever implemented there, the same bug will not appear.
Note that tegra114_spi.c already operates in this fashion.
The clock manipulation code is copied from claim_bus() to probe() rather
than moved. This ensures that any calls to set_speed() take effect; the
clock can't be set once during probe and left unchanged.
Fixes: 5cb1b7b395 ("spi: tegra20: Add support for mode selection")
Cc: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The nvidia,bpmp property is left over from an old BPMP I2C binding, and
shouldn't be present. Remove it from the SoC DT file, and update the
I2C driver not to parse it; the value wasn't used for anything any more
anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra SDHCI binding dictates that the reseet name for the Tegra SDHCI
clock be "sdhci" not "sdmmc", and that the clock is accessed by index
rather than by name. Fix the Tegra186 DT and MMC driver to honor this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra I2C binding dictates that the clock name for the Tegra I2C clock
be "div-clk" not "i2c". Fix the Tegra186 DT and I2C driver to honor this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The spatch series converting legacy drivers from miiphy_register to
mdio_register changed the return convention of the davinci_emac internal
MDIO accessors, making the internal code relying on it misbehaving:
no mdiodev get registered and U-Boot crashes when using net cmds in the
context of the old legacy net API.
ATM davinci_emac_initialize and cpu_eth_init don't return a proper value
in that case but fixing them would not avoid the crash.
This change is just a follow-up to the spatch pass, the MDIO accessors
of the mdiodev introduced by the spatch pass retain their proper values.
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The QMan is not used in FMan IM mode, so no QMI enqueue or QMI
dequeue are performed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ATM when receiving a packet the whole buffer is invalidated, this change
optimizes this behaviour.
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.
This gets rid of the remaining warnings:
CACHE: Misaligned operation at range
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
ATM the rx and tx descriptors are handled as cached memory while they
lie in a dedicated RAM of the SoCs, which is an uncached area.
Removing the said dcache ops, while optimizing the logic and clarifying
the code, also gets rid of most of the check_cache_range() incurred
warnings:
CACHE: Misaligned operation at range
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
BLANCHE is development board based on R-Car V2H SoC (R8A7792)
This commit supports the following periherals:
- SCIF, Ethernet, QSPI, MMC
Signed-off-by: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Building w/ GCC v5.2, the SD card access is broken due to invalid data
in the response command reconstructed at the end of
sh_sdhci_get_response().
Add a memory barrier between the two main steps of this function to
ensure the resp[] table content is consistent before bits reordering.
This fix has been tested Ok on Porter board rev1.0 using v2016.03
release.
Signed-off-by: Yannick Gicquel <yannick.gicquel@iot.bzh>
This can be used in the same way as other R-CAR serial setting.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds support for the SMBus block read/write functionality.
Other protocols like the SMBus quick command need to get added
if this is needed.
This patch also removed the SMBus related defines from the Ivybridge
pch.h header. As they are integrated in this driver and should be
used from here. This change is added in this patch to avoid compile
breakage to keep the source git bisectable.
Tested on a congatec BayTrail board to configure the SMSC2513 USB
hub.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This simple driver provides some functions to control some of the
integrated devices. The watchdog is enabled per default. This driver
adds a function to disable the watchdog. Also the internal legacy
UART (io address 0x3f8/0x2f8) is enabled per default.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
To prevent the compiler error, split the checking condition whether
cfg->ops is NULL or not.
It's more clearly, because it's not included in mmc_config structure
when CONFIG_DM_MMC_OPS is disabled.
drivers/mmc/mmc_legacy.c: In function ‘mmc_create’:
drivers/mmc/mmc_legacy.c:118:31: error: ‘const struct mmc_config’ has no member named ‘ops’
drivers/mmc/mmc_legacy.c:118:58: error: ‘const struct mmc_config’ has no member named ‘ops’
make[1]: *** [drivers/mmc/mmc_legacy.o] Error 1
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the MMC framework was added in u-boot, the mmc_go_idle was
added before mmc_send_op_cond_iter in function mmc_send_op_cond
annotating that some cards seemed to need this. Actually, we still
need to do this in function mmc_complete_op_cond for those cards.
This has been verified on Micron MTFC4GACAECN eMMC chip.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
structure member 'cd_inverted' of omap_hsmmc_data
is available only when OMAP_HSMMC_USE_GPIO is
defined.
When CONFIG_DM_MMC is defined, but not
CONFIG_OMAP_GPIO, this will cause build breakage
in omap_hsmmc driver of the sort:
CC drivers/mmc/omap_hsmmc.o
../drivers/mmc/omap_hsmmc.c: In function 'omap_hsmmc_ofdata_to_platdata':
../drivers/mmc/omap_hsmmc.c:1763:6: error: 'struct omap_hsmmc_data' has no member named 'cd_inverted'
priv->cd_inverted = fdtdec_get_bool(fdt, node, "cd-inverted");
^
Fix this by accessing cd_inverted only when
OMAP_HSMMC_USE_GPIO is defined.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The 'xtfpga' board is actually a set of FPGA evaluation boards that
can be configured to run an Xtensa processor.
- Avnet Xilinx LX60
- Avnet Xilinx LX110
- Avnet Xilinx LX200
- Xilinx ML605
- Xilinx KC705
These boards share the same components (open-ethernet, ns16550 serial,
lcd display, flash, etc.).
Signed-off-by: Chris Zankel <chris@zankel.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Convert the driver to the driver model while retaining the existing
legacy code. This allows the driver to support boards that have
converted to driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add driver model support while retaining the existing legacy code.
This allows the driver to support boards that have converted to
driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Simon Glass <sjg@chromium.org>
AT91 PIO4 controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.
The pin configuration is performed on specific registers which
are shared along with the gpio controller. So regard the pinctrl
device as a child of atmel_pio4 device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Rework the driver to support driver model and device tree, and
support to regard the pio4 pinctrl device as a child of
atmel_pio4 device.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to make these PIO4 definitions shared with AT91 PIO4
pinctrl driver, move them from the existing gpio driver to the
head file, and rephrase them.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the functions passed to the registration function are not in the same
C file (extern) then spatch will not handle the dependent changes.
Make those changes manually.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
For the 4xx related files:
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Run scripts/coccinelle/net/mdio_register.cocci on the U-Boot code base.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The patch is referred to at91 clock driver of Linux, to make
the clock node descriptions in DT aligned with the Linux's.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 302c5db ("dm: tpm: Add Driver Model support for tpm_atmel_twi
driver") converted the Atmel TWI TPM driver itself to driver model, but
kept the legacy-style i2c_write/i2c_read calls.
Commit 3e7d940 ("dm: tpm: Every TPM drivers should depends on DM_TPM")
then made DM_I2C a dependency of the driver, effectively forcing users
to turn on CONFIG_DM_I2C_COMPAT to get it to work.
This patch adds the necessary dm_i2c_write/dm_i2c_read calls to make the
driver compatible with DM, but also keeps the legacy calls in ifdefs, so
that the driver is now compatible with both DM and non-DM setups.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Implement MDIO bus read/write functions, initialize the bus and scan for
the PHY when phylib is enabled. Limit PHY speeds to 10/100 Mbps.
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The ethoc device can be configured to have a private memory region
instead of having access to the main memory. In that case egress packets
must be copied into that memory for transmission and pointers to that
memory need to be passed to net_process_received_packet or returned from
the recv callback.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Addresses used in buffer descriptors and passed in platform data or
device tree are physical. Addresses used by CPU to access packet data
and registers are virtual. Don't mix these addresses and use virt_to_phys
for translation.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add .of_match table and .ofdata_to_platdata callback to allow for ethoc
device configuration from the device tree.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extract reusable parts from ethoc_init, ethoc_set_mac_address,
ethoc_send and ethoc_receive, move the rest under #ifdef CONFIG_DM_ETH.
Add U_BOOT_DRIVER, eth_ops structure and implement required methods.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Don't use physical base address of registers directly, ioremap it first.
Save pointer in private struct ethoc and use that struct in all internal
functions.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add Kconfig entry for the driver, remove #define CONFIG_ETHOC from the
only board configuration that uses it and put it into that board's
defconfig.
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When adding support for the driver model the SPI EEPROM feature had
been ignored. Fix the build with both CONFIG_DM_ETH and
CONFIG_E1000_SPI enabled.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>