Add USB OTG ID pin mux and switch the USB OTG port
from peripheral to OTG mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The DH DRC02 board has an on-board microSD slot,
add DT properties to enable the slot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
threshold configuration (Joshua)
To simplify setup, configuration and compilation of u-boot, define emmc
node for all Espressobin boards. Espressobin boards without populated emmc
works correctly, just detection and initialization of emmc obviously fails.
Code for emmc is extracted from commit f1a43c84a9 ("arm64: dts: a3720:
add support for espressobin with populated emmc").
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Hardware testing of a board using the Armada 385 has shown that an
impedance threshold setting of 0x7 performs better in an eye-diagram
test than with Marvell's recommended value 0x6.
As other boards may still perform better with Marvell's reccomended value,
a configuration option is added with a default value of 0x6.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Introduce weak function board_mem_get_layout() which allows overriding
the memory layout from board code in runtime, useful for handling
different SKU versions.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Introduce initial hierarchy of device trees for Apalis iMX8X
System on Module.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
the mem_map structure containing the size of SDRAM is used in various
cache functions in cache_v8.c thus we need to update it with the
sdram size the board is configured with as well. Without this
the cache functions do not get setup properly and can hang
in the case where a board reports more SDRAM than defined in
PHYS_SDRAM_SIZE.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The used PMIC has been changed from RHOM BD71837 to NXP PCA9450A.
Adjust the device tree accordingly.
Remove the old ADC node as the ADC has been changed and has no longer
a separate power rail.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reduce vital product data size to match the latest specification.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following warning:
arch/arm/mach-imx/imx8/ahab.c:105:3: warning: implicit declaration of function ‘flush_dcache_range’ [-Wimplicit-function-declaration]
flush_dcache_range(s, e);
^~~~~~~~~~~~~~~~~~
Include cpu_func.h header which declares the flush_dcache_range()
function.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c: In function ‘authenticate_os_container’:
arch/arm/mach-imx/imx8/ahab.c:96:9: warning: format ‘%x’ expects argument of type
‘unsigned int’, but argument 9 has type ‘ulong {aka long unsigned int}’ [-Wformat=]
debug("img %d, dst 0x%x, src 0x%x, size 0x%x\n",
Fix those by using "%lu" specified.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c:110:63: warning: format ‘%x’ expects
argument of type ‘unsigned int’, but argument 2 has type ‘u64 {aka long
long unsigned int}’ [-Wformat=]
Fix those by using %llx
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
Activate ARCH_SUPPORT_PSCI as other TEGRA124 target and remove
CONFIG_ARMV7_PSCI and CONFIG_ARMV7_PSCI_NR_CPUS in configs file as they
are migrated in Kconfig.
Select CONFIG_ARMV7_PSCI_0_1 (the first PSCI version),
because CONFIG_ARMV7_PSCI_0_2 and CONFIG_ARMV7_PSCI_1_0
are not activated in this product.
Hi,
This patch depend on the previous serie [1].
I don't test this patch on real hardware but
after this patch the size of the binary don't change.
In .config we have:
CONFIG_ARCH_SUPPORT_PSCI=y
CONFIG_ARMV7_PSCI=y
# CONFIG_ARMV7_PSCI_1_0 is not set
# CONFIG_ARMV7_PSCI_0_2 is not set
CONFIG_ARMV7_PSCI_0_1=y
CONFIG_ARMV7_PSCI_NR_CPUS=4
In u-boot.cfg, this patch only add the 2 lines
#define CONFIG_ARCH_SUPPORT_PSCI 1
#define CONFIG_ARMV7_PSCI_0_1 1
[1] "Convert CONFIG_ARMV7_PSCI_1_0 and CONFIG_ARMV7_PSCI_0_2 to Kconfig"
http://patchwork.ozlabs.org/project/uboot/list/?series=184029
Regards
Patrick
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a tool to update or insert an Octeon specific header into the U-Boot
image. This is needed e.g. for booting via SPI NOR, eMMC and NAND.
While working on this, move enum cvmx_board_types_enum and
cvmx_board_type_to_string() to cvmx-bootloader.h and remove the
unreferenced (unsupported) board definition.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Using ram_get_info() is complicated and does not work after relocation.
Now that gd->ram_size holds the full RAM size, let's use it instead and
remove the ram_get_size logic completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With this patch, gd->ram_size now holds to full RAM size detected by the
DDR init code. It introduces the get_effective_memsize() function to
report the maximum usable RAM size in U-Boot to the system instead.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Octeon has a specific boot header, when booted via SPI NOR, NAND or MMC.
Here the only 2 instructions are allowed in the first few bytes of the
image. And these instructions need to be one branch and a nop. This
patch adds the necessary nop after the nop, to that the common MIPS
image is compatible with this Octeon header.
The tool to patch the Octeon boot header into the image will be send in
a follow-up patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The AT91 architecture now has two possible timer blocks, the old PIT timer
and the new PIT64B.
The timer.c file has an old non DM driver that works for platforms
that do not use the ATMEL_PIT_TIMER DM-based driver.
Update the Makefile to select this old driver in case neither of the
ATMEL_PIT_TIMER and the MCHP_PIT64B_TIMER are selected.
Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA7G5 uses CCF driver under drivers/clk/at91/ and not the custom older
at91 clock.c driver. Remove it from the compilation list and adapt cpu.c
arch_cpu_init() to avoid calling at91_clock_init() which is wrong
anyway.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Align the pin setup for sdhci0 with linux kernel.
This means to have slew rate enable and high drive strength.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Use the reset function to handle the hold boot bit in RCC
with device tree handle with MCU_HOLD_BOOT identifier.
This generic reset allows to remove the two specific properties:
- st,syscfg-holdboot
- st,syscfg-tz
This patch prepares alignment with kernel device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
spl_mmc_boot_partition is only defined when
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION is defined.
Signed-off-by: Richard Genoud <richard.genoud@posteo.net>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The QSPI CS2 is not used on DHCOM, remove the pinmux and flash@1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The uSD slot card-detect GPIO is connected to PG1, fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Correct the ALIGN macro usage in mmu_set_region_dcache_behaviour
call: the address must use ALIGN_DOWN and size can use ALIGN macro.
With STM32_SYSRAM_BASE=0x2FFC0000 and MMU_SECTION_SIZE=0x100000 for
STM32MP15x the computed address was 30000000 instead of 2ff00000.
Fixes: 43fe9d2fda ("stm32mp1: mmu_set_region_dcache_behaviour")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Commit 4b2be78ab6 ("time: Fix get_ticks being non-monotonic")
puts in evidence that get_ticks is called before timer initialization.
Fix it by initializing timer before relocation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Device tree alignment with kernel v5.10-rc1.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Since kernel v4.8-rc1, commit 05b23ebc2bd9 ("ARM: dts: armv7-m: remove skeleton.dtsi include"),
skeleton.dtsi file is no more included.
This synchronization is needed to avoid to get 2 memory node
in DTB file if, in DTS file, memory node is declared with the correct
syntax as following:
memory@90000000 {
device_type = "memory";
reg = <0x90000000 0x800000>;
};
Then in DTB, we will have the 2 memory nodes, which is incorrect and
cause misbehavior during DT parsing by U-boot:
memory {
device_type = "memory";
reg = <0x00 0x00>;
};
memory@90000000 {
device_type = "memory";
reg = <0x90000000 0x800000>;
};
Issue found when synchronizing MCU's STM32 DT from kernel v5.10-rc1.
When using fdtdec_setup_mem_size_base() or fdtdec_setup_memory_banksize()
API, first above memory node is found (with reg = <0x00 0x00>), so
gd->ram_size, gd->ram_base, gd->bd->bi_dram[bank].start and
gd->bd->bi_dram[bank].size are all set to 0 which avoid boards to boot.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Renesas RZ/G2H (r8a774e1) is pin compatible with R-Car H3 (r8a77951),
however it doesn't have several automotive specific peripherals. Add
a r8a77951 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77951 and r8a774e1 SoC.
PFC changes are synced from mainline linux-5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Renesas RZ/G2N (r8a774b1) is pin compatible with R-Car M3-N (r8a77965),
however it doesn't have several automotive specific peripherals. Add
a r8a77965 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77965 and r8a774b1 SoC.
PFC changes are synced from mainline linux-5.9 commit
bbf5c979011a ("Linux 5.9").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
There is no reason to have these macros. But record offsets of missing
register in the structure for future use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
GCC's garbage collector works for Microblaze for quite a long time but none
has enabled it.
The same change has be done for example by commit fac4790491 ("arc:
Eliminate unused code and data with GCC's garbage collector").
Before:
text data bss dec hex filename
588760 33592 39192 661544 a1828 u-boot
After:
text data bss dec hex filename
504504 32164 38608 575276 8c72c u-boot
Which saves almost 15% of memory footprint.
Also group symbols/functions to proper section.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit imports device tree files that are related to Allwinner V3
series from Linux commit 3650b228f83a ("Linux 5.10-rc1").
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The reference design of Allwinner V3 series uses an
AXP203 or AXP209 PMIC attached to the I2C0 bus of the SoC, although the
first community-available V3s board, Lichee Pi Zero, omitted it.
Allow to introduce support for the PMIC on boards with it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner V3/Sochip S3 uses the same die with Allwinner V3s/S3L, but V3 comes
with no co-packaged DDR (DDR3 is usually used externally), and S3L comes
with co-packaged DDR3.
Add support for Allwinner V3/S3 chips by add SoC names to original V3s
choice, and allow to select DDR3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Import updated device trees from Linux tag v5.9. This picks up new
hardware (PinePhone, PineTab); and it drops the U-Boot specific DTSI
files for the Pinebook and the Teres-I, since the ANX6345 bridge is
now supported upstream.
A couple of headers needed updates for recently-added hardware support.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
There are two different publicly-released revisions of the PinePhone
hardware, versions 1.1 and 1.2; and they need different device trees.
Since some GPIO pins were rerouted, we can use that to distinguish
between them.
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Rockchip has many 32bit SoCs and some of them are support SPL_OPTEE now,
only boards with SPL_OPTEE support can fit BINMAN well, other boards
will fail at initr_binman() in U-Boot proper after below patch,
eg. rv1108 board.
83187546ae binman: Support multiple images in the library
Fixes: 79030a4861 ("rockchip: Add Single boot image (with binman, pad_cat)")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Commit c4cea2bbf9 ("rockchip: Enable building a SPI ROM image on bob")
added an alias spi1 referring to spi@ff1d0000, however there was already
an alias spi0 referring to the same node in rockpro64's u-boot.dtsi, and
having both aliases present broke booting from SPI flash for this board.
Remove the spi0 alias, set the default bus for SPI flash to 1, and
enable support for numbered aliases in SPL so that it uses the same bus
numbering as U-Boot proper. This fixes booting from U-Boot in SPI flash
on the rockpro64 board.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bbf9 ("rockchip: Enable building a SPI ROM image on bob")
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
In order to enable the Amlogic SM1 MMC controller fix, we need to add a u-boot specific
MMC controller compatible.
This adds a new meson-sm1-u-boot.dtsi and reworks the other -u-boot.dtsi
to use this for SM1 based boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move the asm/arch-meson/sd_emmc.h to a local meson_gx_mmc.h,
remove the useless if/then and fix the meson_gx_mmc.c include.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The accepted binding uses multiple nodes, one for each table type. Update
coral accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since commit 29d2d64ed5 ("x86: Add support for more than 8 MTRRs"),
the maximum number of variable range MTRRs was increased from 8 to 10.
On the BayTrail platform there are only 8 variable range MTRRs. In
mtrr_commit() it still uses MTRR_MAX_COUNT which caused a #GP during
VESA video driver probe. It should have been updated to use dynamically
probed number.
This fixes the boot failure seen on Intel Minnow Max board.
Fixes: 29d2d64ed5 ("x86: Add support for more than 8 MTRRs")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
patman showing email replies from Patchwork
sandbox poweroff command
minor fixes in binman, tests
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl+kJL8RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaDpAf+MajyuxlmGmFTjpyiB026aWiYE4rAn4AE
bXEDxHpOTIH4hDX7kYVWPmuKivHJo2hF0WUpIFBEAgtc2dOfjOP+mrDjBzG1Pikl
z5yuilG7eHwC1kTIkPv/tPHwDWRBI5VNwTYq0VTtffMKr8LCBo96wEYEbeYK0xdQ
kpNa9d4G+tpx20BCRgPLeOMk2pg5SVszkCCkmmPd12rO2zJ9+wWa8fwA759E93Rw
RshoRCtLNo2nEA3uJVG2aN9n3eAdM/iupDVdBLg50SFKabUxt7OcvGOC8NzGdAmT
9UbB8scvQJyI/kylGT+ghH3o2RqQGvuIRXmDyETckdkpiqK0SQvysg==
=eOGz
-----END PGP SIGNATURE-----
Merge tag 'dm-pull5nov20' of git://git.denx.de/u-boot-dm
patman status subcommand to collect tags from Patchwork
patman showing email replies from Patchwork
sandbox poweroff command
minor fixes in binman, tests
- Add a new SMBIOS parser and enable it when booting from coreboot
- Fix up various driver names to avoid dtoc warnings
- Fully enable ACPI support on Google Chromebook Coral
- Add a way to set SMBIOS properties using the devicetree
- Update existing boards to use devicetree for SMBIOS using a new
default sysinfo driver
Add a file containing defaults for these, using the existing CONFIG
options. This file must be included with #include since it needs to
be passed through the C preprocessor.
Enable the driver for all x86 boards that generate SMBIOS tables.
Disable it for coral since it has its own driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: reword the commit message a little bit]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This uclass is intended to provide a way to obtain information about a
U-Boot board. But the concept of a U-Boot 'board' is the whole system,
not just one circuit board, meaning that 'board' is something of a
misnomer for this uclass.
In addition, the name 'board' is a bit overused in U-Boot and we want to
use the same uclass to provide SMBIOS information.
The obvious name is 'system' but that is so vague as to be meaningless.
Use 'sysinfo' instead, since this uclass is aimed at providing information
on the system.
Rename everything accordingly.
Note: Due to the patch delta caused by the symbol renames, this patch
shows some renamed files as being deleted in one place and created in
another.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Much of the output is not very useful. The bootm command is quite a bit
quieter. Convert some output to use log_debug().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
With Chrome OS the kernel setup block is stored in a separate place from
the kernel, so it is not possible to access the kernel version string.
At present, garbage is printed.
Add a sanity check to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add logging for each part of the boot process, using a new
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
At present the top of available DRAM is the same as the top of the range
of the low-memory MTRR.
In fact, U-Boot is allowed to use memory up until the start of the FSP
reserved memory. Use that value for low_end, since it makes more memory
available.
Keep the same calculation as before for mtrr_top, i.e. the top of
reserved memory.
A side-effect of this change is that the E820 tables have a single entry
that extends from the bottom of the memory used by U-Boot to the bottom
of the FSP reserved memory. This includes the bloblist, if ACPI tables
are placed there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is useful when using Linux's earlycon since the MMIO address must be
provided on some platforms, e.g.:
earlycon=uart8250,mmio32,0xddffc000,115200n8
However this is only for debugging, so don't show it by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This table is not needed if a v2 TPM is in use. Add a condition to avoid
adding it when not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Quite a few log_info() calls are included in the x86 code which should use
log_debug() instead. Convert them to reduce unwanted output.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use log_debug() instead of debug() in this file, to enable the extra
features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Set up a few fields necessarily to make Chrome OS boot without showing a
firmware error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present CONFIG_CHROMEOS is used to determine whether verified boot is
in use. The code to implement that is not in U-Boot mainline.
However, it is useful to be able to boot a Chromebook in developer mode
in U-Boot mainline without needing the verified boot code.
To allow this, use CONFIG_CHROMEOS_VBOOT to indicate that verified boot
should be used, and CONFIG_CHROMEOS to indicate that the board supports
Chrome OS. That allows us to define CONFIG_CHROMEOS on coral.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is not possible to boot Chrome OS properly without passing some basic
information from U-Boot. This applies even if verified boot is not being
used. Add a structure definition for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if SSDT and DSDT code is created, only the latter is retained
for examination by the 'acpi items' command. Fix this by only resetting
the list when explicitly requested.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The current implementation for DSDT tables is not correct for the case
where there is generated code, as the length ends up being incorrect.
Also, we want the generated code to go first in the table.
Rewrite this piece to correct these problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If there is nothing in the SSDT we should not include it in the tables.
Update the implementation to check this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful for this command to show the address of the interrupt table.
Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present these tables do not have the correct header, and there is an
occasional incorrect value due to uninited data. Fix these bugs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present these functions are incorrect. Fix them and add some logging
and checking to avoid future problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present all tables are placed starting at address f0000 in memory, and
can be up to 64KB in size. If the tables are very large, this may not
provide enough space.
Also if the tables point to other tables (such as console log or a ramoops
area) then we must allocate other memory anyway.
The bloblist is a nice place to put these tables since it is contiguous,
which makes it easy to reserve this memory for linux using the 820 tables.
Add an option to put some of the tables in the bloblist. For SMBIOS and
ACPI, create suitable pointers from the f0000 region to the new location
of the tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: squashed in http://patchwork.ozlabs.org/project/uboot/patch/
20201105062407.1.I8091ad931cbbb5e3b6f6ababdf3f8d5db0d17bb9@changeid/]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
---------------------
- new boards : GE (new B1x5v2), phytec phyCORE-i.MX8MM
- converted doc to reST
- fixes for verdin-imx8mm (Toradex)
- fixes for i.MX thermal driver
- mx7ulp: Align the PLL_USB frequency
- mx53: primary/secondary bmode
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/741465284
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCX6QsVQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76Z29ACfRdzFocIVEOFNm8v5yA1C/FU9q9sAn1kEAot5
vkm2yvDQ7+9vl5G7+ZRn
=rCCX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20201105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx for 2021.1
---------------------
- new boards : GE (new B1x5v2), phytec phyCORE-i.MX8MM
- converted doc to reST
- fixes for verdin-imx8mm (Toradex)
- fixes for i.MX thermal driver
- mx7ulp: Align the PLL_USB frequency
- mx53: primary/secondary bmode
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/741465284
Up to now the sandbox would shutdown upon a cold reset request. Instead it
should be reset.
In our coding we use static variables like LIST_HEAD(efi_obj_list). A reset
can occur at any time, e.g. via an UEFI binary calling the reset service.
The only safe way to return to an initial state is to relaunch the U-Boot
binary.
The reset implementation uses execv() to relaunch U-Boot.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
During a cold reset execv() is used to relaunch the U-Boot binary.
We must ensure that all files are closed in this case.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The command to shut down a device is 'poweroff'. It is a deficit of the
sandbox that it does not support resetting yet but shuts down upong seeing
the 'reset' command.
Once the sandbox properly supports reset we need the 'poweroff' command to
leave the sandbox.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the sandbox eth-raw device host_lo is removed this leads to closing
the console input.
Do not call close(0).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is required by Chrome OS so that the audio and other unibuild
features work correctly. Add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These settings are included twice. The second lot are correct, so drop the
others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The bloblist guarantees that blobs are zeroed so there is no need to do
an additional memset(). Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we create the ACPI context but then drop it after generation of
tables is complete. This is annoying because we have to then search for
tables later.
To fix this, allocate the context and store it in global_data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present write_tables() can fail but does not report this problem to its
caller. Fix this by changing the return type.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>